Transcript
104 60
200
294
338
135º
Ø 32
DBL250 / DBL275
DOLPHIN COUNTER MOUNTED ELECTRONIC INFRARED TAP WITH TEMPERATURE ADJUSTMENT LEVER › WRAS Approved product › Touch Free Electronic Tap – Tap is activated when the user brings hands within the State of the art electronic infrared sensor’s range › Ultimate Hygiene - Prevents cross contamination. Ideal for counter top basins › Flow time once user's hands are removed from the tap - 1 second (adjustable by using remove control DB51) › Flow rate – 3.8 litres/minute with our standard fitted flow regulator at any pressure between 0 and 6 bar (other flow rates such as 1.89 and 1.33 LPM available to special order – please enquire) › Quality polished or brushed chrome plated brass finishes available › Tap settings may be adjusted by using remote control (DB50) › Filters, fixing bolts, installation instructions and power source supplied with each tap › WRAS approved › 2 year manufacturer's warranty › Mandatory Hygiene Flush is available - can be set to 12,24 or 48 Hour intervals optional extra & must be specified when ordering › Complies with SKA rating criteria › The two flexible connectors contain integral check (non-return) valves › Interchangeable STD M22/24 Neoperl Aerator insert › We recommend our Dolphin Blue DB61 TMV3 be used in conjunction with this Dolphin Blue tap › Our low flow taps are fully BREEAM compliant and contribute to up to five BREEAM WAT 1 credits.
HEIGHT
338
MM
44
MM
104
MM
DIAMETER PROJECTION
› Power Source: 9 Volt Battery (features low battery warning) / Plug-in 9 Volt transformers (supplied) › Water Supply: hot and cold supply - featuring temperature adjustment lever › 3/8" BSP Water supply connection › Operating pressure 0.5 - 8.0 bar (7 - 116 PSI) › Maximum water temperature 70ºC › Water Supply : Hot and Cold › Counter: Hole : diameter 34-36mm › Min-Max thickness : 2-27mm
PRODUCT CODES BATTERY POWERED › Polished Chrome Plate › Brushed (Satin) Chrome Plate
DBL250C DBL250S-2
TRANSFORMER POWERED › Polished Chrome Plate › Brushed (Satin) Chrome Plate
DBL275C DBL275S-2
TECHNIC AL HELPLINE 01424 202224 DOLPHINSOLUTIONS.CO.UK
DB225C **
Data Sheet
Correct for DB200, DB225, DB250, DB275, DBL200, DBL225, DBL250, DBL275 taps Shop Order No.:
DB225C
"O"-Ring No.:
******
Bag No. Insert No.
******
Date:
******
[bar]
0.15
0.20
0.30
0.50
1.00
1.50
2.00
3.00
4.00
5.00
6.00
[l/min]
0.85
1.04
1.40
2.56
4.54
5.63
6.50
7.96
9.21
10.33
11.37
Description Neostrahl
No. 1
[l/min]
0.83
1.00
1.41
2.15
3.83
4.76
5.46
4.98
5.20
5.18
5.01
PL-HC-LP 5.0L
No. 2
[l/min]
0.66
0.81
1.25
2.41
4.18
5.21
6.01
7.35
8.41
8.34
8.53
PL-HC-LP 8.0L
No. 3
[l/min]
0.71
0.88
1.27
2.22
3.89
4.64
4.12
4.20
4.26
4.12
3.93
[l/min]
0.53
0.63
0.77
1.03
1.37
1.42
1.44
1.57
1.69
1.77
1.82
2.0L Spray
No. 5
[l/min]
0.66
0.84
1.21
1.93
3.55
4.44
5.14
6.11
5.99
6.04
6.17
Supplied PL-HC 6.0L
No. 6
0.11
0.13
0.21
0.50
1.02
1.37
1.67
2.13
2.52
2.78
3.11
PL-HC-LP 1.0GPM No. 4
Std.-Dev .
Now supplied as standard with PL-HC 1.0GPM aerator/flow regulator - No. 4 above 12.00
11.00
10.00
9.00
8.00
7.00
6.00
5.00
4.00
3.00
2.00
1.00
0.00 0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
pressure [bar]
31.10.13
DB225C
UK-JB 31-07-2009
INSTALLATION AND MAINTENANCE GUIDE
INFRARED TAPS Electronic taps – saving water, saving power, promoting hygiene
DB100 DB125 DB150 DB175
DB200 DB225 DB250 DB275
DBL200 DBL225 DBL250 DBL275
Important: Read carefully before installing product
Revision January 2017
INDEX
3
Technical Data : battery powered taps
4
Technical Data : transformer powered taps
5
Pack Contents
6
Pre Installation Information
7-9
Tap Installation
10-11
Range Adjustment using Dolphin Blue Remote Control – DB51 Adjusting the sensor range with a remote control
12
Battery Replacement DB100, DB150, DB200, DB250, DBL200, DBL250 models
13
Maintenance Filters cleaning instructions Care and cleaning of chrome and special finishes
14
Trouble Shooting
15
Spare Parts List
17
Warranty
2 | Dolphin Blue | DB100, DB200 & DBL200 Ranges
TECHNICAL DATA Technical details for B AT T E RY powered taps Power Supply
9V (1 x 9v PP3)
Security Time
90 seconds. Can be reduced with the remote control
Recommended
0.5-8.0 bar (7-116 PSI)
Water Pressure
With water pressure of more than 8 bars use a pressure reducing valve for reduction
Preset sensor range
220mm
Minimum sensor range
80mm
Maximum sensor range
300mm
Hot water temperature
Max 70ºC
DB100, DB200 & DBL200 Ranges | Dolphin Blue | 3
TECHNICAL DATA Technical details for T R A N S F O R M E R powered taps Power Supply
9V Transformer
Security Time
90 seconds. Can be reduced with the remote control
Recommended
0.5-8.0 bar (7-116 PSI)
Water Pressure
With water pressure of more than 8 bars use a pressure reducing valve for reduction
Preset sensor range
220mm
Minimum sensor range
80mm
Maximum sensor range
300mm
Hot water temperature
Max 70ºC
4 | Dolphin Blue | DB100, DB200 & DBL200 Ranges
PACK CONTENTS Familiarise yourself with the part’s names and confirm that the parts are included. DB100 3
DB200 DBL200
1
1 1 x tap and attachment 2 1 x filter 3 1 x battery box
2
DB125 DB225 DBL225 1 1 x tap and attachment 2 1 x filter
1
3
3 1 x transformer 2
DB100, DB200 & DBL200 Ranges | Dolphin Blue | 5
PRE INSTALLATION INFORMATION Check contents • Separate all parts from the packaging and check each part with the ‘pack contents’ section. • Pay attention to the different model variations. • Make sure all parts are accounted for before discarding any packaging material. • If any parts are missing, do not attempt to install your electronic tap until you obtain the missing parts. Warnings • Do not install facing a mirror or any other elctronic system operated by an infrared sensor. • To prevent reflection problems, it is recommended to keep a minimum distance of 1.5 metres between the tap and any other objects. Preparation for installation • Flush water supply lines thoroughly before installing the tap. • Do not allow dirt, Teflon tape or metal particles to enter the tap. • Shut off the water supply. Important • All plumbing is to be installed in accordance with applicable codes and regulations. • Installations in Australia and New Zealand must comply with the requirements of AS/NZS 3500 Recommended hole size
Recommended hole size
Ø28mm min
Ø28mm min
Ø34mm max
Ø34mm max
Standard versions
6 | Dolphin Blue | DB100, DB200 & DBL200 Ranges
Tall versions
TAP INSTALLATION
Familiarise yourself with the part’s names and confirm that the parts are included. DB150
1
DB250 DBL250 3 1 1 x tap and attachments 2 2 x filters
2
3 1 x battery box
DB175 DB275
1
DBL275 3 1 1 x tap and attachments 2 2 x filters 3 1 x transformer 2
DB100, DB200 & DBL200 Ranges | Dolphin Blue | 7
TAP INSTALLATION
Step 1 – Remove all mounting hardware 1 Shut off water supply and remove the hexagonal nut, the disk
O ring Gasket Disk Hexagonal nut
Step 2 – Installing the tap 1 Place the tap with O-ring into the hole in the basin or basin/sink. Make sure the
O ring
O-ring is located between the counter or basin/sink and the bottom of the tap. O ring Gasket
2. Slide the gasket over
Disk
flexible hose(s).
Hexagonal nut 3. Secure the tap to the counter or basin/sink with the hexagonal nut and the disk.
8 | Dolphin Blue | DB100, DB200 & DBL200 Ranges
TAP INSTALLATION
Step 3 – Connecting the Water Source 1. a. DB100, DB125, DB200, DB225, DBL200, DBL225: connect the flexible pipe to the water supply b. DB150, DB175, DB250, DB275, DBL250, DBL275: connect the red flexible pipe to the hot water supply and the blue flexible pipe to the cold water supply. 2. Make sure the filter(s) are installed between the flexible pipe and the shut off valve (not supplied). 3. Turn on the central
Flex hose
Flex hose
water supply and the shut off valve. 4. Check for leaks.
Filter Filters
Step 4 Connecting the Shut off valve Shut off valves Power Source 1. a. DB100, DB150, DB200, DB250, DBL200, DBL250: connect the power source, Install the battery’s box at the wall under the sink using the two sided adhesive foam tape. The cable connection must point down. (You can use an optional extension cable in order to assemble the battery box up to ten feet from the sink. See “Spare parts list”). b. DB125, DB175, DB225, DB275, DBL225, DBL275: plug the transformer into the electrical socket and DB125, DB175, connect the connectors. DB225, DB275, DBL225, 2. Important: Wait a few DBL275 seconds before activating the tap to avoid entering into ‘adjustment mode’. 3. If range is unsatisfactory, refer to the section entitled ‘Range adjustment’.
DB100, DB150, DB200, DB250, DBL200, DBL250
DB100, DB200 & DBL200 Ranges | Dolphin Blue | 9
RANGE ADJUSTMENT
Adjusting the sensor with the remote control This tap was supplied with a Self Adjusting Sensor. The ideal detection range for the specific location will be set automatically. DETECTION RANGE: Only if necessary, use the remote control to adjust the sensor range as follows: Shut off the water supply. Hold the remote control straight in front of the sensor in a distance of about 6 - 8” (15 - 20cm). Choose the function RANGE by pressing once at the range function button. After pressing this function button, a quick flashing of the red light at the front of the sensor will occur. At this stage, you can increase or decrease the sensor range by pressing the (+) or the (-) buttons, every push will increase or decrease one level. Note: Once you have changed the detection range with the remote control, this distance will be remembered by the sensor, even if the power source is disconnected. To get back to the self adjustment mode, use the ADJ button only. Adjusting other settings with the remote control SECURITY TIME: The Security time, prevents continuous running of water due to reflections or vandalism. By default, if the sensor is covered for more than 90 seconds the water flow will shut automatically. To resume regular operation any obstruction must be removed. Press the SEC button. Wait until a quick flashing of the red light of the sensor eye is perceived. Then, press + to increase the security time and – to reduce it. DELAY IN TIME: It is recommended to change the delay in time for flush valves for urinals or toilets only. If required, the delay in time can also be modified in taps as follows: Press the IN button. Wait until a quick flashing of the red light of the sensor eye is perceived. Then, press + to increase the delay in time and – to reduce it.
10 | Dolphin Blue | DB100, DB200 & DBL200 Ranges
RANGE ADJUSTMENT
DELAY OUT TIME: This button allows modifying the water flow time after the user removes his hands from the tap. A delay out time close to 0 will save more water. An increased delay out time will make the user experience more comfortable. The factory setting for delay out time is 1 second. If required, the delay out time can be modified as follows: Press the OUT button. Wait until a quick flashing of the red light of the sensor eye is perceived. Then, press + to increase the delay out time and – to reduce it. 24 HOUR HYGIENE FLUSH: If you have a compatible model with a 24 hours hygiene flush it is possible to enable and disable it . To activate the hygiene flush, press the clock button. Wait until a quick flashing of the red light of the sensor eye is perceived. Then press + to activate the hygiene flush or – to deactivate it. TEMPORARY OFF FUNCTION: This function is ideal to perform any kind of activity in front of the sensor without operating the system (for example, cleaning). The tap will remain shut for 1 minute when this button is pressed once. To cancel this function and to return to normal operation press the On/Off button again or wait 1 minute. RESET BUTTON: This function restores all the factory settings except for the sensor range. If required, press the Reset button and without releasing it, press the + button once. Note: To enter the self adjusting mode, use the ADJ button. To change the sensor range, use the RANGE button.
DB100, DB200 & DBL200 Ranges | Dolphin Blue | 11
BATTERY REPLACEMENT
For models DB100, DB150, DB200, DB250, DBL200, DBL250 Battery models only When the battery weakens, the red indicator light will blink at a constant rate. The battery must be replaced within two weeks. To replace the battery 1
Carefully open the battery’s box
2
Remove the old battery
3
Replace the used battery with a new 9V battery (Lithium battery is
recommended)
1
4
2
3
Close the box
12 | Dolphin Blue | DB100, DB200 & DBL200 Ranges
4
MAINTENANCE
Filter Cleaning Instruction This tap is provided with one/two stainless steel filter(s) preventing foreign particles to enter the lines. If the water flow has decreased, this may be because the filter(s) is/are clogged. The filter(s) can be changed as follows: 1
Shut off the water shut-off valve
For DB100, DB125, DB200, DB225, DBL200, DBL225 2
Disconnect the flexible pipe
For DB150, DB175, DB250, DB275, DBL250, DBL275 2
Disconnect the red and blue flexible pipes
3
Remove the filter(s) and wash it/them under running water
4
Reassemble the parts.
5
Reconnect the flexible pipe(s) and restore the incoming water supply.
6
Make sure that there is no water leakage.
Care and cleansing of chrome and special features DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or the like. Use of any prohibited cleansing or maintenance products or substances could damage the surface of the tap. For surface cleansing of the tap use only soap and water, then wipe dry with clean cloth or towel. When cleaning bathroom tiles, the tap should be protected from any splattering of harsh cleansers.
DB100, DB200 & DBL200 Ranges | Dolphin Blue | 13
TROUBLE SHOOTING
PROBLEM
INDICATOR Sensor flashes continuously when user’s hands are within the sensor’s range
No water comes out of the tap
Red light in the sensor does not flash once when user’s hands are within the sensor’s range
CAUSE
Low batteries
Replace batteries
Range is too short
Increase the range with remote
Range is too long ie tap has gone into security mode
Decrease the range with remote
Batteries are completely used up
Replace batteries
Sensor is picking up reflections ie tap has gone into security mode
Decrease the range or eliminate cause of reflection
Connectors between the electronic unit and the solonoid are disconnected Red light in the sensor flashes once when user’s hands are within the sensor’s range
Sensor flashes once when user’s hands are within the sensor’s range Water flow from spout does not stop
Water flow diminished
Red light in the sensor does not flash when user’s hands are within the sensor’s range
SOLUTION
Debris or scale in solonoid
Connect the electronic unit connectors to the solonoid Unscrew solonoid, pull out the plunger and the spring from the solonoide and clean them. Use scale remover material if needed. When replacing the plunger,please make sure that the spring is in vertical position
The central orifice in the diaphragm is plugged or the diaphragm is torn
Unscrew solonoid and clean the orifice and/or replace diaphragm
The water supply pressure is higher than 8 bars
Reduce the water supply pressure
Debris or scale in diaphragm
Unscrew solonoid, remove diaphragm and clean or replace. Use scale remover if needed.
Sensor is dirty or covered
Clean or eliminate cause of interference
Sensor is picking up reflections from the washbasin or another object
Decrease the range or eliminate case of reflection
Filter or aerator is clogged
Remove, clean and reinstall
14 | Dolphin Blue | DB100, DB200 & DBL200 Ranges
SPARE PARTS LIST DB100 Item Description
Part No.
– 20 19 25 15a 8 9
Seals and Screws Kit DB07210007 O-ring O-ring O-ring Gasket Screw Screw
– 11 25
Sensor Kit Infra-Red Sensor O-ring
DB07220183
– 13 14
Filter Adapter Kit Filter Nipple
DB07212001
– 2 20
Cover Kit Cover O-ring
DB07270004
– 7 10
Solenoid Valve Kit Solenoid valve Diaphragm
DB07230003
10
Diaphragm
DB04500001
21 21
Battery box (IP 67version) DB83F Battery box DB82F
23 23
9V Transformer (100mA) 9V Transformer (300mA)
DB70F DB85F
DB100, DB200 & DBL200 Ranges | Dolphin Blue | 15
SPARE PARTS LIST DB200 Item Description /Part No. – 20 19 15a 8 9 25 – 11 25 – 13 14 – 2 20 – 7 10
Sensor Kit DB07220009 Infra-Red Sensor O-ring Filter Adapter Kit DB07212001 Filter Nipple Cover Kit DB07270003 Cover O-ring Solenoid Valve Kit DB07230003 Solenoid valve Diaphragm
10
Diaphragm DB04500001
21
Battery box (IP 67 version) DB83F Battery box DB82F
21
23 23
16 | Dolphin Blue | DB100, DB200 & DBL200 Ranges
Seals and Screws Kit DB07210007 O-ring O-ring Gasket Screw Screw O-ring
9V Transformer (100mA) DB70F 9V Transformer (300mA) DB85F
LIMITED WARRANTY
This product is covered by a limited warranty for two years from date of purchase. During this period, Dolphin Solutions Ltd undertakes, at its option, to repair or replace any faults caused by defective materials or manufacturer defaults that may arise. The guarantee does not cover faults or damage caused by incorrect installation and/or manufacture, wear and tear, battery or water compositions. This includes but is not limited to the following: • incorrect installation, inversions or supply pipes • Pressures or temperatures exceeding recommended limits • Improper manipulations, tampering, bad or lapsed maintenance • Foreign bodies, dirt or scale introduced by the water supply
DB100, DB200 & DBL200 Ranges | Dolphin Blue | 17
18 | Dolphin Blue | DB100, DB200 & DBL200 Ranges
Tel: +44 (0)1424 20 22 24 Fax: +44 (0)1424 205 200
[email protected] www.dolphinsolutions.co.uk Southpoint, Compass Park, Bodiam, Robertsbridge, TN32 5BS Dolphin Solutions Ltd egnaR letoH elbamusnoC s
tcudorP seilimaF
smeti detaleR
noitallatsnI ediuG
178 Dolphin Dispensers page 180 DBL 400
Technical helpline page 11 WP 106
ybaB gnignahC
• Operating pressure 0.5–8.0 bar (7–116 PSI) • Maximum water temperature 70ºC • 2 year manufacturer ’s warranty • WRAS Approved Product
sliaR barG moorhsaW seirosseccA
page 178 DB 200
combat Legionella – please specify at time of orering • Mandatory Hygiene Flush feature can be specified to control (DB51 – see page 188) • Tap settings can be adjusted manually or by using remote • Neopearl Aerator please specify at time of ordering) • Flow rate – 6 litres/minute (down to 1.89 litres/minute page 183 – premixed applications. For 2 inlet hot and cold feed see TMV3 thermostatic mixing valve is recommende • Water Supply: d for Single inlet cold or pre-mixed – a TMV2 plated brass finishes or available • Quality polished chrome plated brass or lacquered nickel contamination • Touch Free Tap – for ultimate hygiene – prevents cross
page 105 WP 112R
01424 202224 page 159 BC 2006
• Powered by 9v plug in transformer • Powered by 6 DB 225S x AAA / 9v PP3 battery DB 200S (designed to match brushed stainless steel) Brushed nickel finish • Powered by 9v plug in transformer • Powered by 6 x AAA / 9v PP3 battery Polished chrome finish Product Codes
DB 225C DB 200C
page 190-191 low battery warning) – for other power source options see • Power: Plug-in 9 volt transformers or 9 volt battery (with • 3/8" BSP water supply connector • Counter hole Ø 28-34mm Min-max thickness 2-27mm • Power Connections: tap male, power source female • Projection 105mm • H 142 x Ø 45 mm Product Data
0800 0723 404 paoS sresnepsiD
source Power
Ø50 Ø45
001 135°
Counter Mounte d
241
eussiT telioT lew oT repaP noitani resnepsiD bmoC dnaH riA t resnepsiD oH stinU sreyrD
spaT
sniB
DB 200 / DB 225 Dolphin Blue Infrared Tap
page 12 WP 208R
105
Taps
Bellchem WD9 174-269 taps, bins, access.qxd :Layout
DOLPHIN
1
Request your 320 page catalogue today on
DBL250/DBL275 Tap Range - Parts Diagram
Item 6 17 5 15a 8 9
11 5
13 22
14 19
Part No. DB07210022
O-ring O-ring O-ring Gasket Screw Screw
Sensor Kit
DB07220042
Infra-Red Sensor O-ring
Filter and Back Check Adapter Kit
DB08520003
Back check and Filter adapter Filter Nipple
-
Cover Kit
2 6
Cover O-ring
-
Solenoid Valve Kit
DB07270003
DB07230003
7 10
Solenoid valve Diaphragm
10
Diaphragm
DB04500001
Mixer Handle kit
DB07260002
12 20 21
Handle Axis O-ring
22
Battery Box (IP67 version) Battery Box
DB83F
9V Transformer (100mA) 9V Transformer (300mA)
DB70F
22 18 18
T: 01424 202224
Description Seals and Screws Kit
F: 01424 205200 E:
[email protected] www.dolphindispensers.co.uk
DB82F
DB85F
Dolphin Blue Infrared Systems Important Design Tips
DOLPHIN
Dolphin Blue Infrared Systems Designing a washroom including Dolphin Blue Infrared Systems Dolphin Blue Infrared Taps, Shower Controls and Urinal Flush Valves offer significant water and energy savings. However, there are some simple DO’s and DON’Ts and TIPs which will help avoid 99% of the situations often associated with infrared systems for washrooms. It should be noted that these details are not exhaustive but will help eliminate 99% of situations. It is recommended that for larger projects especially where design restraints will result in taps being set on minimum or maximum settings, we would advise a very simple mock-up be set with materials to be used to ensure infrared device operates as desired.
DO’s Battery Back up
Pressure
DO include a battery back-up device when installing a transformer powered infrared tap in an accessible washroom.
DO ensure the static and dynamic pressure at the Dolphin Blue device is within the tolerances stated on the product literature / data sheet (please ask if you cannot find it). Most devices are tested to operate between 0.5 and 8 bar. If pressures are outside the stated tolerances please contact the Technical Helpline on 01424 20 22 24.
Security Time DO ensure security time is set at approximately 20 seconds on infrared taps especially in locations susceptible to vandalism. Also important: to be set at 20 seconds to comply with ECA/WTL scheme.
Flow Rate DO specify what flow rate is required when placing your order. Taps - 6 litre / minute is standard. 4 litre / minute is readily available.
Filters Do ensure filters supplied with the Dolphin Blue device are installed. It may not be sufficient to rely on the filters often included with thermostatic mixing valves as the gauge of the filter mesh may not be fine enough. It is also important to ensure pipes are flushed prior to connection and filters are inspected on a regular basis. Time between inspections will depend on hardness and quality of water.
Shower head - 9 litres/ minute is standard, 8 litres / minute is available. Distance from Transformer Please speak to the Dolphin Technical Helpline for other flow rates if required.
It is recommended you ensure the maximum distance between a Dolphin Blue Infrared Tap and its power source is 5 metres.
DON’Ts Mirrors
Panel Mounted Infrared Taps
It is not advisable to locate a Dolphin Blue Infrared device directly opposite a mirror where the infrared eye faces the mirror in such a way that it could reflect itself as this can cause false activations even if the mirror is 2-4 metres away from the infrared eye.
It is very important to ensure the distance between the sensor and the bottom of basin when installing a panel mounted Dolphin Blue Tap with an integral sensor is a minimum of 300mm above the bottom of the basin.
Two Infrared Taps It is not advisable to locate infrared taps directly opposite each other where the infrared eyes face each other as this can also cause false activations even when there is a fair distance between them.
TIPs
Minimum 300mm distance critical
Polished Traps and Sink Surfaces When installing a Dolphin Blue Panel Mounted Tap with an integral sensor it is recommended that you avoid a highly polished chrome trap or sink surface – it will act like a mirror to the tap sensor, potentially causing false activations and wasted water
Avoid polished/ chrome strainers
High Visibility Clothing
‘Tall’ Version Taps and Spout Lengths
It is a feature of most infrared devices in the washroom market that the reflective strips on high visibility clothing may cause the device to operate, even if someone just walks past, with no intention of using it.
Consider the position of the water outlet / aerator in relation to the basin.
The DB51 Dolphin Blue Remote Control can be used to reduce the range of a device to reduce these false activations but may not eliminate the phenomena completely.
Please feel free to discuss spout lengths with the Dolphin Technical Helpline on 01424 2022 24.
washrooms worth experiencing
0800 0723 404 Bell-Chem Products Company Haywood Way, Hastings, TN35 4PL
[email protected] www.dolphindispensers.co.uk
DOLPHIN
