Transcript
GAINWISE TECHNOLOGY
MANUAL
DOOR INTERCOM SS91BV-M / SS1204A(E)V-M GSM / WCDMA INTERCOM (ACCESS CONTROL SYSTEM)
For your protection, read these instructions completely And keep them for future reference. SS91BV-M GSM Intercom
1
Revision E15 ,May 2015
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTION ...................................................................... 3 SS91BV-M GSM INTERCOM INTRODUCTION ....................................................... 4 SS91BV-M GSM INTERCOM WITH ACCESSORIES ............................................... 4 INSTALLATION............................................................................................................... 5 SS91BV-M GSM Intercom Unit ................................................................................... 6 Wiring Diagram .............................................................................................................. 6 LED Indicator ............................................................................................................... 7 SS91BV-M GSM INTERCOM OPERATION ............................................................... 8 Enter Listener Monitoring Mode .................................................................................. 10 Enter Access Control Mode .......................................................................................... 10 Enter Programming Mode ............................................................................................. 10 Programming ..................................................................................................................11 Door/ Gate Release ..................................................................................................... 12 Check GSM Signal Strength ....................................................................................... 14 Check Relay Status ..................................................................................................... 14 Administrator Number....................................................................................................14 CHECK A LOG OF DIAL IN AND DIAL OUT NUMBERS VIA E-MAIL OR SMS .... 15 USER COMMANDS ............................................................................................................. 18 HOW TO RESET THE HARDWARE WHEN YOU FORGET YOUR PASSWORD.........20
SPECIFICATIONS .......................................................................................................... 20 QUICK PROGRAMMING VIA SMS ............................................................................. 22 TROUBLESHOOTING (Q&A) ....................................................................................... 23
SS91BV-M GSM Intercom
2
Revision E15 ,May 2015
Thank you for purchasing SS91BV-M GSM Intercom. Please read this manual carefully before using. Be sure to keep this manual for future reference in case of any problem or question should arise.
IMPORTANT SAFTY INSTRUCTIONS When using this SS91BV-M GSM Intercom, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury. Please read the following before using your equipment. 1. Follow all warning and instructions on the product. 2. Unplug all the connections of product before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 3. Do not use this product near water. 4. Do not use this product near an area where there is a potential of gas leaks or near any fumes that can be explosive. 5. Do not place this equipment near or over a radiator or any other heat source. 6. Do not overload the wall outlet or power cord where the power adapter is installed. This can result in fire or electric shock 7. Avoid spilling liquid on this equipment and do not insert any objects through the ventilation slots. 8. Avoid using the equipment during an electrical storm. There is a remote risk of electrical shock from lighting.
SS91BV-M GSM Intercom
3
Revision E15 ,May 2015
SS91BV-M GSM INTERCOM INTRODUCTION The GSM Intercom SS91BV-M is an intercom system, installed at the entrance of a building. It is an ideal product replacing the traditional door phone. It allows you to speak with visitors standing at the entrance of your company or house entrance from a remote location. A visitor, by simply pressing the call button establishes a mobile call with you. During the call you will be able to activate realty. This SS91BV-M GSM Intercom gives you the opportunity not only to know who is waiting at the entrance from a remote location but also to control the access point. Use of SS91BV-M GSM Intercom at your company or house does not require any special installation and wiring. Simply install the SS91BV-M and connect the door latch and power supply.
SS91BV-M GSM INTERCOM WITH ACCESSORIES Item
Description
Q’ty
Included
1
SS91BV-M - GSM Intercom
1
◎
2
Power adapter
1
◎
3
External antenna
1
◎
4
Mounting Bracket for antenna
1
◎
5
Operational manual
1
◎
SS91BV-M GSM Intercom
4
Optional
Revision E15 ,May 2015
INSTALLATION This GSM Intercom is suitable for both flush and surface mounting.
Note: For surface mounting, you will have to remove the plastic enclosure before fitting main station into the stainless steel cabinet.
SS91BV-M GSM Intercom
5
Revision E15 ,May 2015
SS91BV-M GSM Intercom Unit
Speaker
Call Button Microphone
Wiring Diagram
SS91BV-M GSM Intercom
6
Revision E15 ,May 2015
LED INDICATORS 1. LED “Intercom Status “ Indicator LED
Status
Yellow (standby)
Flashes once per 5 seconds
Yellow (using)
Solid
2. LED ‘Network “Indicator LED
Status
Green (ready)
Flashes once per 3 seconds
Green (searching) Flashes once per second Green (busy)
Solid
3. LED “ Power “ Indicator LED
Status
Red (power on)
Solid
Red (power off)
Off
1. SIM card Register your SIM card with the network, and check it works in a mobile phone You MUST remove the PIN request from the SIM before inserting it in the unit SS91BV-M. Ensure the power is OFF before inserting the SIM card. Carefully side the SIM holder in the OPEN direction, insert the SIM, and slide in the CLOSED direction to lock it in place. 2. Antenna Install the antenna as high as possible on the top of the pillar for best possible reception. 3. Door Lock Connect an electric door lock to terminals marked “door latch”. 4. Power Supply Connect a 12 volt DC power supply to terminals marked “AC, AC” The power supply should be capable of supplying a constant current of no less than 1amp. 5. After a final check of wiring , switch on the power 6. Allow 20~30 seconds for the unit to boot up and detect the network. Once successful connection has been made, the unit will sound a confirmation tone and the status LED will begin flashing. SS91BV-M GSM Intercom
7
Revision E15 ,May 2015
SS91BV-M GSM INTERCOM OPERATION When the visitor pushes the call button to activate the SS91BV-M ring tone will be heard from the GSM intercom. At the same time connection is established with the phone number that is stored in the SS91BV-M. If the first number is busy or not answered the call can be diverted to the second and the third.. The remote phone answers the call from SS91BV-M and starts conversation with the visitors. During conversation press * on your mobile for door open. The relay switches can also be temporarily or permanently switched on or off by press # and 1.
Enter system menu There are three different modes under system menu. 1.
Listener monitoring mode
2.
Access control mode
3.
Programming mode
To gain access to the system menu via dial in, follows these steps: 1.
Call the telephone number of the GSM intercom
2.
Wait for the intercom to answer and signal by one beep to enter system menu
3.
Enter the password of the mode you would like to enter
4.
Password correct one beep, password error 3 beeps.
5.
3 times failure attempt on password , hang up the call
SS91BV-M GSM Intercom
8
Revision E15 ,May 2015
SS91BV-M GSM Intercom
9
Revision E15 ,May 2015
Enter Listener Monitoring Mode 1.
Call the telephone number of the GSM intercom
2.
This device will then verify your phone number with your predefined numbers.
3.
You will hear a “Do” tone to enter listener monitoring mode by pressing【*13*1212＃】 where 1212 is the password.
4.
You are now in the” listener monitoring mode”.(you can hear the live sound of the intercom’s surrounding environment)
* Under this mode speaker is OFF.( 35＃: turn on speaker ) * You can still control the relay output when you are under listener monitoring mode but speaker must be ON status. Enter Access Control Mode 1.
Call the telephone number of the GSM intercom.
2.
This device will then verify your phone number with your predefined numbers.
3.
You will hear a “Do” tone to enter access control mode by pressing【*33*5678＃】where 5678 is the password.
4.
The door will be opened after enter the correct password
*(To open the door by password, if the number is not stored in the access control section) Enter Programming Mode 1.
Call the telephone number of the GSM intercom
2.
This device will then verify your phone number with your predefined numbers.
3.
You will hear a “Do” tone to enter into programming mode by pressing【*12* 1234＃】where 1234 is the password.
4.
You are now in the “programming mode” Note: At the end of each command there can be one of the two indications: Successful: a long “beep” tone, failed: three short “beep” tone.
5.
To make changes on settings please refer to the user commands.(P15,16)
6.
To end programming mode just hang up.
NOTE: *To be successful in programming, originate a call from a land line and enter the digits slowly or using programming by text message.
SS91BV-M GSM Intercom
10
Revision E15 ,May 2015
Programming Programming can be carried out either by dial into the GSM intercom or by text message (Certain programming feature can only be set up by text message, please refer to user commands P.15)
Programming by text message Programming by text message is the simplest way to customize the settings of the GSM intercom and add or delete telephone numbers. Simply send texts in the format to the telephone number of the SIM within the GSM intercom. Note: 1.
A Single SMS text messages is limited to 140 characters.
2.
You can program many different user command codes in one text message with SMS command format. *12*1234 # [command Code1] # [command Code 2] # [command Code3] #........
3.
Each SMS must start with the pass code , default 1234 in the following format *12*1234 # Followed immediately by a command.
4.
To program a call button numbers DO NOT enter country code, just the complete number as you would dial it.
Example:
Storing a call button phone number (Max 3 numbers) and delete 2&3 phone numbers.(Refer to user commands P.16) 058 57235 (landline number 1) Command to use: *12*1234#1[ Y][ phone number]# 086 5682554 (mobile number 2) 086 2235644 (mobile number 3)
Y= number 1, 2 or 3
SMS format: (storing a call button phone numbers) *12*1234#1105857235#120865682554#130862235644# SMS format: (delete 2&3 phone numbers from a call button) *12*1234#12*#13*# User command code CORRECT
SMS format: *12*1234#1105857235#120865682554#130862235644# SMS reply: 1105857235#120865682554#130862235644# OK User command code ERROR (user command 19 error)
SMS format: *12*1234#1105857235#190865682554#130862235644# SMS reply: 110587235#190865682554# Error SS91BV-M GSM Intercom
11
Revision E15 ,May 2015
Progrmming by dial in Note: programming dial in can’t be used from telephones which are already programmed to open the door when they dial the GSM intercom but you can disable Caller ID display (withhold the number) on the mobile before using. To gain access to the programming mode via dial in, follows these steps: Example: Storing a telephone number for dial in door release Enter Programming Mode by Pressing…..
*12*1234# (1234 is default password) A successful pass code will produce a single long beep. A failed attempt will produce 3 short bleeps. You may now program up to 1150 telephone numbers into memory. Use the following commands to program the unit * Insert international country code (1~3 digits): 71 [ country code] # * Add a number (up to 1150 numbers):72 [relay][telephone number] # * Delete a number: 73 [ telephone number ] # * Delete all numbers: 73*#
Door /Gate Release (ring in to open) This GSM intercom also has an extra feature to allow user to gain access from their mobile phone by two methods. 1. Caller ID recognition 2. by access control password mode 1. Caller ID recognition to open Ring in to open the door for authorized telephone number. It can support for up to 1150 users.
When GSM Intercom receives a call from user, it will check the calling number and if the number is in the list, the GSM Intercom will drop the call and then open the gate / door. The GSM Intercom doesn’t answer the call, it simply checks the caller ID, and so it won’t cost you anything to open the gate / door.
SS91BV-M GSM Intercom
12
Revision E15 ,May 2015
For Caller ID recognition to open the door or gate you need to program the mobile numbers and country code into the memory before using.
Example:
Ireland Country code: 353 (UK: 44 / USA: 1) 086 5683624 (mobile number 1) 086 5682554 (mobile number 2) 086 2235644 (mobile number 3) Command to use: *12*1234#71[country code]#72[relay] phone number] #72[relay][ phone number] #72[relay][ phone number] #....... SMS format: *12*1234#71353#7210865683624#7210865682554#7220862235644# To delete phone numbers of dialing in to open
SMS format: (to delete phone number 1 and 2) *12*1234#730865683624#730865682554# SMS format: (to delete all numbers) *12*1234#73*# After the numbers are programmed you can also send the text message to check the stored numbers by sending SMS format *21# , then the GSM intercom will reply the phone number list text message.
2. Access control password to open Dial the SIM card telephone number. The unit will answer the call and you will hear a bleep tone. *33*5678# (trigger relay 1) *34*5678# (hold relay 1) *35*5678# (release relay 1)
*36*5678# (trigger relay 2) *37*5678# (hold relay 2) *38*5678# (release relay 2)
*Above operation same as sending SMS commands *This is for door open option for telephone numbers not stored.
SS91BV-M GSM Intercom
13
Revision E15 ,May 2015
Check GSM signal strength (0~31 levels) When a request for GSM signal strength SMS is sent to the GSM intercom it will reply with a signal strength code and service provider name. The code will be between 0~31 means the signal level is from poor to best. Example: SMS format *20# SMS reply: Vodafone Signal Level = 31 【Signal is very strong】
Check Relay Status You can send SMS command code to check relay status. SMS format *22# SMS Reply Relay=ON Detect = ON【Relay=Hold , Detect=GND】 Remark: Terminal mark” Detect” (see wiring diagram) is for you to connect a door reed switch. The gates would have a reed switch wired through the” DET” input to ground. It’s used by the user to check if the gates are open or closed.
Administrator Number Once the administrator number is stored, the unit will only accept programming from this number and only via SMS programming. Example:
Program a mobile number as an administrator number via SMS Mobile number: 0865682554 Command to use *12*1234#74 [Admin number]# SMS format
*12*1234#740865682554# To delete the Admin number *12*1234#74*#
SS91BV-M GSM Intercom
14
Revision E15 ,May 2015
Check A Log Of Dial In And Dial Out Numbers Via E-mail Or SMS This system allows you to save dial in numbers log and will then automatically send the record via e-mail or SMS as your request. There is a list of commands you need and examples to guide you on the settings for this feature. Please setup following required parameters and commands before you can use it. NOTE: G-mail doesn’t support this feature. o.
Function
SMS command codes *12*1234#83[N]#
1
Auto sending a log of dial in numbers
N= 0 (sending when it reaches 100 numbers)- default N=1 (sending when it reaches 200 numbers, Max)
Sending record when it reaches 200 numbers. / command code example: *12*1234#831# 2
Way of sending a log of dial in numbers via e-mail or SMS
Sending record via email 3
*12*1234#84[N]# N=0 (no saving /sending record) N=1 (via SMS, 4 numbers limited/SMS) N=2 (via E-mail)
/ command code example: *12*1234#842#
GPRS parameters setting
*40*1234#APN, auth_type,user name,password# auth_type: 0= none / 1= PAP / 2= CHAP
Command code Example: E-mail parameters setting
4
( Doesn’t support Gmail)
*41*1234#SMTP server,port,user name, password, e-mail address, e-mail sender name#
Command code Example :
5
Recipient & Carbon copy settings
*42*1234# recipient e-mail address, recipient name, carbon copy e-mail address, carbon copy name#
Commande code example:
SS91BV-M GSM Intercom
15
Revision E15 ,May 2015
No. 6
Function
SMS command codes
E-mail subject setting
*43*1234# e-mail subject#
Command code Example:
7
8
To immediately send current dial in numbers log via email or SMS
*44*1234# SMS reply: successful or failed *4[N]*1234# N=0 ( reply GPRS parameters) N=1 ( reply e-mail parameters) N=2 ( reply recipient & carbon copy)
Check parameters setting
N=3 ( reply e-mail subject) Check GPRS parameters setting /
Command code example: *40*1234#
9
Mobile number for receiving a log of dial in numbers via SMS
*12*1234#85[mobile number.]#
10
Delete mobile number for receiving a log of dial in numbers via SMS
*12*1234#85*#
11
SIM phone number used in intercom for Clock date and time correction
*12*1234#86[SIM phone number used in the intercom]#
12
To delete SIM phone number used in the intercom for Clock date and time correction
*12*1234#86*#
Remark: why you need to setup the number for system time clock date and time correction? This device has a time clock and supports automatically updating their date and time via NITZ information from network. In case some of the networks are not available for NITZ information, we strongly suggest to setup this clock date and time correction. When the device detects NITZ information is not available from the network will automatically send a command to itself via the SIM card used in the intercom for time correction which will keep your “ dial in numbers log” with correct date and time.
Log Example:
Ｉ: Dial in number / Ｏ: Dial out number SS91BV-M GSM Intercom
16
Revision E15 ,May 2015
How to program checking a log of dial in numbers via SMS There are 3 programming codes you will need to make this feature work
You can program many different user command codes in a single text message with SMS command format. *12*1234 # [command Code1] # [command Code 2] # [command Code3] #........ Example: Mobile number for receiving a log 0907967223 SIM phone number used in opener 0948778458 *12*1234#841#850907967223#860948778458# Send *44*1234# to check log
Replied log information via SMS example:
I: Dial IN numbers N: Next text massage E: End text message
SS91BV-M GSM Intercom
17
Revision E15 ,May 2015
To gain access to the different modes and control relay (by dial in) No.
Function
command
Description
Default
1
Enter Programming Mode
*12* [ password ] #
Programming by calling
1234
2
Enter Monitoring Mode
*13* [ password ] #
To hear the surroundings where
1212
the intercom installed
3
Enter Access control
*33* [ password ] #
Password mode access option
5678
*34* [ password ] #
To hold relay to keep door
5678
Mode (Trigger relay 1)
4
Hold Relay 1
opened
5
Release Relay 1
*35* [ password ] #
To release relay for door close
5678
6
Trigger relay 2
*36* [ password ] #
Password mode access option
5678
7
Hold Relay 2
*37* [ password ] #
To hold relay to keep door
5678
opened
8
Release Relay 2
*38* [ password ] #
SS91BV-M GSM Intercom
18
To release relay for door close
Revision E15 ,May 2015
5678
User commands to check system info & control relay via SMS No. 1
Function check signal strength
Command *20#
Reply Signal Level 0~31 from poor to best Service provide name, network
2
Check stored numbers
*21#
O [ number]…,I [ number]…..E (N) O：call button numbers list I：dial in to open numbers list E：End N：Next SMS
3
Check relay status
*22#
Relay [ status],Detect [ status ] Status: ON / OFF
4
Trigger relay 1
*33* [ password ] #
No reply (default password:5678) (Latch on when relay is on hold status)
5
Hold relay 1
*34* [ password ] #
No reply (default password:5678)
6
Release relay 1
*35* [ password ] #
No reply (default password:5678)
7
Trigger relay 2
*36* [ password ] #
No reply (default :5678) (Latch on when relay is on hold status)
8
Hold relay 2
*37* [ password ] #
No reply (default :5678)
9
Release relay 2
*38* [ password ] #
No reply (default :5678)
●
SMS data error
(Only 0~9、*、# are available)
SMS Data Error
●
Function code error
SS91BV-M GSM Intercom
Function Code Error
19
Revision E15 ,May 2015
User commands table You can program many different user command codes in one text message with SMS command format. *12*1234 # [command Code1] # [command Code 2] # [command Code3] #........ No. 1
Feature Change programming
Command
Description
Default
01 [ password ] #
password:4 digit codes
1234
02 [ password ] #
password:4 digit codes
5678
03 [ password] #
password:4 digit codes
1212
1 [ Y ] [ phone number ] #
Y= phone number 1,2 or 3
None
Password
2
Change access control password
3
Change monitoring mode password
4
Store a call button phone number
Max 3 phone numbers phone No.:3~15 digit codes
5
Delete a call button
1[ Y ]*#
Y= phone number 1,2 or 3
Phone number
None
phone No.:3~15 digit codes
6
Speaker Volume
3 [ speaker volume] #
speaker volume level:0 ~ 4
3
7
Microphone Volume
4 [ microphone volume] #
microphone volume level:0 ~ 4
3
8
Relay Time
51 [ relay time ] #
relay time: 1~9999 sec
1
9
Relay 2 Time
50 [ relay 2 time ] #
relay time: 1~9999 sec
1
10
Call no answer time and
52 [ no answer time ] #
No answer time :10~99 sec
20 sec
divert to next number
11
Max call Time
53 [ max call time] #
Max call time:005~999 sec
060 sec
12
Max monitoring time
55[ duration time] #
duration time:00 ~ 60 mins
10 mins
00 ( no limit)
13
Change relay1 trigger code
61 [ X ] #
X=0~9 / * /＃
*
14
Change rely 1 hold code
63 [ X ] #
X=0~9 / * /＃
#
15
Change relay 1 release code
64 [ X ] #
X=0~9 / * /＃
1
16
Change relay2 trigger code
67 [ X ] #
X=0~9 / * /＃
7
17
Change rely 2 hold code
68 [ X ] #
X=0~9 / * /＃
8
18
Change relay 2 release code
69 [ X ] #
X=0~9 / * /＃
9
71 [ country code ] #
Country code:1~3 digit codes
1
72[relay] [ phone number ] #
Relay: 1 or 2
73 [phone number ] #
Delete phone number
73*#
Delete all phone numbers
19
Ring in to open the door (Max: 1150 numbers)
SS91BV-M GSM Intercom
20
Revision E15 ,May 2015
20
Add administrator phone number
74 [ admin number ] #
admin number: 3~15 digit codes ( no number no restriction)
None
21
Del administrator phone number
74*#
delete administrator phone number
None
X=0 (disable) X=1 (enable) 894+X#
22
Disable, enable SMS reply notice
23
Dial tone volume
24
Reset
Disable , enable SMS replay
Relay 1 trigger, relay 2 trigger Relay 1 hold, relay 2 hold Relay 1 release, relay 2 release
0
898+X#
X=1~4 ( levels)
3
999#
reset default
None
How To Reset The Hardware When You Forget your Password
SS91BV-M GSM Intercom
21
Revision E15 ,May 2015
Quick programming via SMS Program a call button phone number. (Max 3 numbers) Note: To program a call button numbers DO NOT enter country code, just the complete number as you would dial it. Command to use: *12*1234#1[Y][ phone number]# Y= number 1, 2 or 3 Examples: 058 57235 (landline number 1) 086 5682554 (mobile number 2) 086 2235644 (mobile number 3) SMS format: *12*1234#1105857235#120865682554#130862235644#
Program a phone number for dial in door release (Max 100 numbers) Note: Program a phone number for dial in door release you NEED TO enter country code Command to use: *12*1234#71[country code]#72[relay] phone number] #72[relay][ phone number] #72[relay][ phone number] #....... Example: Ireland Country code: 353 (UK: 44 / USA: 1) 086 5683624 (mobile number 1) 086 5682554 (mobile number 2) 086 2235644 (mobile number 3) SMS format: *12*1234#71353#7210865683624#7210865682554#7220862235644#
Operation When intercom calling your phone and you have answered the call… Press * to trigger relay1 Press 7 to trigger relay 2 Press # to hold relay 1 Press 8 to hold relay 2 Press 1 to release relay 1
Press 9 to release relay 2
Sending SMS commands *33*5678# (trigger relay 1) *34*5678# (hold relay 1) *35*5678# (release relay 1)
*36*5678# (trigger relay 2) *37*5678# (hold relay 2) *38*5678# (release relay 2)
*20# (check reception level) *21# (check stored number) *22# (check gate / door status) SS91BV-M GSM Intercom
22
Revision E15 ,May 2015
Troubleshooting (Q &A) .Q.
The unit powers up but there is a bleeping from the door station. A. This means the unit is not able to detect the network for some reason. -Check the SIM card is activated and has calling credit. -Power off the unit, remove the SIM and check it in a mobile phone to verify it can make a call. -Check the SIM does not ask for a PIN code when put in a phone. If it does, then disable the PIN code request. -Check the SIM is a standard GSM SIM, not 3G or 4G only SIM. If you are unsure, contact your SIM card provider to verify. Frequency of operation should be any one of the international quad band standards, 850 / 900 / 1800 / 1900 MHz -Check the reception is good. Poor reception is not sufficient. -Check the antenna has been mounted as high as possible, not near large metal objects, or wet green shrubs etc. -Check the antenna connection. Visually inspect that the centre pin inside the antenna is intact, and has not been pushed back inside the fitting. Q. The unit calls the first number, but there is not enough time to answer before it diverts to the next number. A. Increase the no answer time as per programming instructions. Q. The unit calls the first number but voicemail comes on before it can ring the second number. A. Decrease the no answer time as per programming instructions. Q. The caller ID part does not work. A. Be sure to program the caller ID part under 72 feature. If your number is a private or number withheld, then it will not work. Even if you have already programmed a number to receive a call from the intercom, if you also want that number to have caller ID access, it must be programmed under the 72 feature also. Ensure the number is entered as you would normally dial it from another phone. Q. There is no audio from the gate, but the person at the gate can hear ok. A. This can be due to low reception. -Check reception level by *20#. -Change SIM card if necessary to another network which may have better coverage. -Purchase a high gain antenna.
SS91BV-M GSM Intercom
23
Revision E15 ,May 2015
Q. The audio quality that can be heard on the remote telephone is poor or humming (buzzing). A. A small amount of GSM buzz can be considered normal on GSM intercoms, but not so much that causes inability to hear the person speaking. This can be caused by the GSM antenna being mounted too close to the speech panel or not mounted high enough. -Try earthling the speech panel chassis to 0V of the power supply. -This is also a symptom of poor reception. Try above steps on checking and improving reception. Q. The * or # key does not work when the intercom calls a phone. A. Check if you can hear the relay clicking at the gate when the * or # key is pressed during a call. If it can be heard, then the system is working, check wiring between the relay and the lock or gate panel. If the relays do not make a clicking sound, then check this feature on a different mobile cell phone or landline. If it works on a different phone, check the settings on the phone in question under DTMF tones. Failure of DTMF tones to operate correctly is also a symptom of low reception. Check steps above on improving reception. Try pressing the buttons longer when attempting to activate the gates or door.
SPECIFICATION: Operating Voltage
12 to 24 Volt AC/DC
Operating Current
Maximum 250 mA, Typically 55mA
GSM / WCDMA Module
Cinterion / Simcom
GSM / WCDMA Frequency
GSM 850/900/1800/1900 Mhz, WCDMA 850/1900 or 900/2100 Mhz
Physical size
Face plate: 170 x 100 mm, Stainless cabinet: 174 x 113 x 65 mm
Length of antenna
3 meters cable
Humidity
Less than 80% RH
Operating Temperature
-20℃ to 50℃
SS91BV-M GSM Intercom
24
Revision E15 ,May 2015
