Doorking 6300 Swing Gate Operator Quick Start

Transcript

QUICKSTART “BASIC” GUIDELINES FOR MODEL 6300 - FOR GATES UP TO 18 FEET AND OPENING 90° Model 6300 is intended for installation only on swing gates used for vehicles. Pedestrians must be supplied with a separate access opening. 120 Glasgow Avenue Inglewood, California 90301 U.S.A. GATE OPERATOR MUST BE PROPERLY GROUNDED!! op Lo Tip: It is recommended that a surge suppressor be installed on the high voltage power lines. D t ke ac e at G t ke ac Br 37 ad .5” ow Lo 3” op Safety Cover 24 Elbow Flange ” Important: Elbow flange MUST be on the opposite side of the closed gate. Manually adjust the arms to get the correct open and closed positions BEFORE powering up the operator. Open/Close limits will be automatically set the first time operator is cycled. Operator Output Shaft B 0 #2 to 11 om to # 7 C 1. elay to # R lt 2. 4 Vo 2 3. C nk le xib Flenduit Co Post Base Conduit Left Support Leg 22” Concrete 12” 14” 1.5” Output Shaft 12” 3” 12” Output Shaft Position 23” Right Support Leg 10” Conduit Run conduit on the opposite side of the open gate for the post base. Post Base f te o m tto Bo Concrete Pad 3” 2” Post Base MUST be Level. Open Gate Open Gate 5” 43” Pad Base 0 630 h Higlt o V Pla ion nct Ju Pad MUST be Level. 30” 3/8 Secure operator to the concrete pad with six (6) 3/8” x 3” sleeve anchors (not supplied). m Cra 1 D 16.5” Chassis Ground Ar Note: 2” thick 43” gate Illustrated. OR 230 VAC/460 VAC 7 • NO AC power. • NO DC power (On select models). High Voltage Conduit k 23” 1. OFF (Opening Counter-Clockwise) 2. OFF 3. OFF 4. OFF 5. OFF (Normal Reverse Function) 6. OFF 7. OFF 8. OFF Important: The elbow assembly must be in the correct position on the arms BEFORE cycling operator the first time. an 90° 2 11 A Mount the post base into the concrete before installing the operator. Adjust 1 to 23 sec. Cr 3 Closed Gate 90° SW 2 A 20 Concrete Position Closed Gate Elbow Assembly B SW 1 3. OFF 4. ON 5. ON (Operator Type) 6. OFF 7. ON (Single Operator) 8. ON (Tamper Protect) Chassis Ground 230/460 VAC Br Using shadow loop and gate opening in direction shown. Auto Close 1. OFF Timer 2. OFF e as Sh Important: A straight line drawn from the closed gate bracket through the open gate bracket MUST intersect the operator output shaft. HIGH VOLTAGE! 230/460 VAC e at B st Po 43” Neutral DIP-Switch Settings G Open Gate se Ba Note: 2” thick gate Illustrated. 115 VAC DANGER d Pa 90° 115 VAC Gate Bracket 115 VAC Hot Closed Gate 115 VAC Neu 12” 115 VAC Neu Operator Position 34” High Voltage Connection se er ev R For safety and installation instructions, please refer to the owner’s manual. ACwer Ponduit Co ” 3/4 eeps w hS p Loo Co it ndu Po 1 we rA 2 Manual Release w Lo lt Vo DANGER xes HIGH VOLTAGE! Bo the of is h pt e De ncret by co ined s rm ition e det cond ocal l l soi and des. o c ing d l i bu Gate Bracket wit Gate Bracket Height Ground Copyright 2010 DoorKing, Inc. All rights reserved. High Voltage Conduit Loop Detectors C Not included - Refer to the Owner’s manual and Arms and Operator MUST be level. Bottom Plate of 6300 Loop Information Manual (available from www.dkaccess.com) for more information on loops and loop detectors. 30” Crank Arm 5” Flange 60” Connecting Arm Varies with base used. Use two legs of incoming 3-phase power. rm Brass Bushing Crank Power Arm Elbow Assembly Important: Adjust the locknut on the crank power arm so that it is snug against the washer, but will still allow the 30” crank arm to rotate with little force. Radio Receiver D Not included - Refer to a specific Radio Receiver Manual (available from www.dkaccess.com) for more information on radio receivers and antenna installation. 6300-066-F-4-10