Transcript
FSTRT Flat Screen 0 - 15 Tilt Truss Mount Direct Monitor Attachment
FSTRT VESA Mounting Plate
Determine which type of monitor attaching hardware is required for the monitor as specified by the monitor manufacturer. Various sizes of monitor attaching screws are provided for convenience (See the Hardware List below) If mounting the monitor directly to the FSTRT VESA Mounting Plate, follow the Direct Monitor Attachment instructions. If mounting the monitor using an Adaptor Plate, follow the Monitor Attachment with Adaptor Plate instructions.
Direct Monitor Attachment Phillips Head Screw
A
Use fasteners as specified by the monitor manufacturer to attach the monitor directly to the FSTRT VESA Mounting Plate. (DETAIL A)
Monitor Threaded Insert
Monitor Not Included
DETAIL A
Monitor Attachment with Adaptor Plate Secure the Adaptor Plate to the FSTRT VESA Mounting Plate with the provided hex bolts, nuts, and washers. (DETAIL B) Refer to the specific Adaptor Plate instructions to attach the adaptor plate to the monitor.
Monitor Attachment with Adaptor Plate Adaptor Plate Sold Separately Shown with FSUL Series Adaptor
Hardware List 3/8-16 x 1-5/8" U-Bolt ......................................................................... 4 3/8-16 Hex Nuts, Black ........................................................................ 16 3/8" Flat Washers, Black ..................................................................... 12 3/8" Nylock Nuts, Black ....................................................................... 4 3/8-16 x 3/4" Hex Bolt, Black .............................................................. 2 1/2-13 Nylock Nuts, Black .................................................................... 2 5/16-18 x 3/4" Hex Bolts, Black .......................................................... 4 5/16" Flat Washers, Black ................................................................... 8 5/16-18 Hex Nuts, Black ...................................................................... 4
Washer Hex Bolt
B FSTRT_Ins (9/05)
Washer Hex Nut
DETAIL B ©2005 Lucasey Manufacturing Corporation, Oakland, California
4mm x 25mm Set Screws ... 5mm x 30mm Set Screws ... 6mm x 30mm Set Screws ... 4mm x 12mm Phillips Screws ... 5mm x 12mm Phillips Screws ... 6mm x 12mm Phillips Screws ...
4 4 4 4 4 4
4mm Hex Nuts 5mm Hex Nuts 6mm Hex Nuts 5mm Flat Washers 1/4" Flat Washers
... 8 ... 8 ... 8 ... 12 ... 12
www.lucasey.com
Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1
FSTRT Flat Screen 0 - 15 Tilt Wall Mount U-Bolt Pipe Clamp Washer
U-Bolt
Hex Nuts
Attaching Truss Mounting Plate to Truss Section 1. Align the FSTRT Truss Mounting Bracket U-Bolt holes with the Truss Section. Make sure all four U-Bolts will align with an open space in the Truss. 2. Place a U-Bolt Pipe Clamp between the FSTRT Truss Mounting Bracket and the Truss tubing. 3. Place a U-Bolt through the Pipe Clamp and the FSTRT Truss Mounting Bracket. Secure with a Hex Nut on each leg of the U-Bolt. 4. Repeat steps 1 and 2 for all four U-Bolts. Loosely hand tighten the Hex Nuts and adjust the position on the FSTRT Truss Mounting Bracket. 5. After double checking to make sure the FSTRT Truss Mounting Bracket is level and in the correct position on the Truss Section, tighten the Hex Nuts and secure with a second Hex Nut on each U-Bolt leg.
Truss Section
FSTRT Truss Mounting Bracket
Attaching Monitor to Truss Mounting Bracket 1/2-13 Nylock Nuts 3/8-16 Hex Bolts
1. Raise the monitor with attached brackets to the FSTRT Wall Mounting Bracket and slip the slots of the FSTRT VESA Mounting Plate over the studs on the FSTRT Wall Mounting Bracket. Check to make sure the FSTRT VESA Mounting Plate Slots are fully engaged and seated. 2. Adjust Tilt to the desired viewing angle. 3. Secure with the provided Nylock Nuts and Hex Bolts.
FSTRT Truss Mounting Bracket FSTRT VESA Mounting Plate FSTRT_Ins (9/05)
©2005 Lucasey Manufacturing Corporation, Oakland, California
www.lucasey.com
