Transcript
Driver Guide For use with all Vode systems. This guide includes technical information to help you quickly choose a driver. Vode uses a variety of drivers to meet the requirements of each LED product. Drivers are selected and programmed depending on rail type, power requirements, dimming protocols and LED type. If a specific driver data sheet is required, please contact Vode or your Vode agent.
Vode supplies 18 gauge multi-core wire harnesses for all driver to rail connections (except Vode ZipWave | 707). Vode does not approve the use of other wiring, doing so may void your warranty. All drivers provided are equiped with a luminaire quick disconnect on the line voltage power side.
Vode Technical Support: (707) 996-9898
Vode does not supply dimming controls. To ensure compatibility please contact driver manufacturer or consult the Vode Dimmer Compatibility guide.
Remote Driver Distance
Button board™ vs. Zipper board™
Depending on driver type, remote drivers may be installed up to 72’ (21.25 m) from the fixture. Vode supplies a 25’ wire harness for installation when necessary, (longer leads are available. IMPORTANT: Do not exceed maximum allowable distance (see following pages for details). To calculate remote distance, add arm length (A) plus distance from arm to driver (B)
Vode has two LED board types, Button and Zipper.
Remote Driver Housing Dimensions: 24.5” (622 mm) X 1.9” (48 mm) X 1.9” (48 mm) Remote Driver Housing B
Zipper board Low power LEDs with a 0.16” (4mm) pitch. A variety of optics are available for each system.
A
Tunable Output & Tunable Wattage If your lumen or power (W) requirements aren’t met by Standard Output, Vode can program the driver to adjust the lumen output and system wattage. Please contact Vode or your Vode agent for details. All drivers are universal 120v-277v with the exception of AH2: Lutron 2-wire, which is only available in 120v.
Button board High power LEDs with a 1.5” (38mm) to 2” (51mm) pitch, depending on the product. Optics are included to control the beam angle.
Copyright © 2016 Vode Lighting LLC. All rights reserved. The Vode logo and Vode, are either registered trademarks or trademarks of Vode Lighting LLC in the United States and/or other countries. All other brand or product names are trademarks or registered trademarks of their respective owners. No part of the above drawing, design, arrangements or ideas thereon shall be duplicated or used for any purpose whatsoever without the express permission of Vode Lighting LLC. Due to ongoing innovation, specifications may change without notice. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C | Page 1 of 15
LED Driver Guide Driver Compatibility : Available for either Remote or Integral power housing : Available for only Remote power housing*
Driver compatibility is determined by rail type, output and rail lengths. See the chart below for driver compatibility with your rail section lengths.
Low Output (LO) with Vode Zipper Board 107 | BoxRail 107 | RaceRail 107 | WingRail 117 | K1 BoxRail* 117 | K1 RaceRail* 117 | K1 WingRail*
12” (305mm)
24” (610mm)
36” (914mm)
48” (1219mm)
60” (1524mm)
72” (1829mm)
96” (2438mm)
2W, 6V
6W, 15V
9W, 24V
12W, 32V
15W, 41V
18W, 50V
22W, 50V
AE eldoLED 0-10v, 1.0% Dimming AT eldoLED 0-10v, 0.1% Dimming AD eldoLED DALI, 0.1% Dimming AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)2 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
AE eldoLED 0-10v, 1.0% Dimming
107 | DoubleBox 107 | DoubleRace AT eldoLED 0-10v, 0.1% Dimming 117 | K2 BoxRail* AD eldoLED DALI, 0.1% Dimming 117 | K2 RaceRail* 117 | K2 WingRail* AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1)
1 1 1
AH2 Lutron Hi-lume 1% 2-wire (LTE)2 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
707 | ZipOne 707 | ZipTwo 707 | ZipThree 707 | ZipWave* 907 | BoxRail
2W, 6V
6W, 15V
9W, 24V
12W, 32V
15W, 41V
18W, 50V
22W, 50V
4W, 9V
7W, 18V
10W, 27V
13W, 35V
16W, 44V
20W, 53V
22W, 50V
AE eldoLED 0-10v, 1.0% Dimming AT eldoLED 0-10v, 0.1% Dimming AD eldoLED DALI, 0.1% Dimming AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)2 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
* 707 | ZipWave and the 117 series are only available in integral power 1 For Integral power mounting, only one driver is supplied. The two lights can not be operated separately. 2 Only available for 120v
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C | Page 2 of 15
LED Driver Guide Driver Compatibility : Available for either Remote or Integral power housing : Available for only Remote power housing*
Driver compatibility is determined by rail type, output and rail lengths. See the chart below for driver compatibility with your rail section lengths.
Standard Output (SO) with Vode Zipper Board 107 | BoxRail 107 | RaceRail 107 | WingRail 117 | K1 BoxRail* 117 | K1 RaceRail* 117 | K1 WingRail*
12” (305mm)
24” (610mm)
36” (914mm)
48” (1219mm)
60” (1524mm)
72” (1829mm)
96” (2438mm)
4W, 6V
11W, 15V
17W, 24V
23W, 32V
29W, 41V
35W, 50V
46W, 50V
AE eldoLED 0-10v, 1.0% Dimming AT eldoLED 0-10v, 0.1% Dimming AD eldoLED DALI, 0.1% Dimming AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)2 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
AE eldoLED 0-10v, 1.0% Dimming
107 | DoubleBox 107 | DoubleRace AT eldoLED 0-10v, 0.1% Dimming 117 | K2 BoxRail* AD eldoLED DALI, 0.1% Dimming 117 | K2 RaceRail* 117 | K2 WingRail* AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1)
1 1 1
AH2 Lutron Hi-lume 1% 2-wire (LTE)2 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
707 | ZipOne 707 | ZipTwo 707 | ZipThree 707 | ZipWave* 907 | BoxRail
4W, 6V
11W, 15V
17W, 24V
23W, 32V
29W, 41V
35W, 50V
46W, 50V
6W, 9V
13W, 18V
19W, 27V
25W, 35V
31W, 44V
37W, 53V
46W, 50V
AE eldoLED 0-10v, 1.0% Dimming AT eldoLED 0-10v, 0.1% Dimming AD eldoLED DALI, 0.1% Dimming AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)2 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
* 707 | ZipWave and the 117 series are only available in integral power 1 For Integral power mounting, only one driver is supplied. The two lights can not be operated separately. 2 Only available for 120v
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C | Page 3 of 15
LED Driver Guide Driver Compatibility : Available for either Remote or Integral power housing : Available for only Remote power housing*
Driver compatibility is determined by rail type, output and rail lengths. See the chart below for driver compatibility with your rail section lengths.
High Output (HO) with Vode Zipper Board 107 | BoxRail 107 | RaceRail 107 | WingRail 117 | K1 BoxRail* 117 | K1 RaceRail* 117 | K1 WingRail*
12” (305mm)
24” (610mm)
36” (914mm)
48” (1219mm)
AE eldoLED 0-10v, 1.0% Dimming
60” (1524mm)
72” (1829mm)
2
2
4
4
96” (2438mm)
AT eldoLED 0-10v, 0.1% Dimming AD eldoLED DALI, 0.1% Dimming AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)3 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
9W, 6V
21W, 15V
33W, 24V
45W, 32V
AE eldoLED 0-10v, 1.0% Dimming
107 | DoubleBox 107 | DoubleRace AT eldoLED 0-10v, 0.1% Dimming 117 | K2 BoxRail* AD eldoLED DALI, 0.1% Dimming 117 | K2 RaceRail* 117 | K2 WingRail* AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1)
57W, 41V
70W, 50V
2
2
4
4
92W, 50V
1 1
AH2 Lutron Hi-lume 1% 2-wire (LTE)3 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
707 | ZipOne 707 | ZipTwo
9W, 6V
21W, 15V
33W, 24V
45W, 32V
AE eldoLED 0-10v, 1.0% Dimming
57W, 41V 2
70W, 50V
46W, 44V
55W, 53V
92W, 50V
2
AT eldoLED 0-10v, 0.1% Dimming AD eldoLED DALI, 0.1% Dimming AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)3 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
707 | ZipThree 707 | ZipWave* 907 | BoxRail
10W, 9V
19W, 18V
28W, 27V
37W, 35V
2
AE eldoLED 0-10v, 1.0% Dimming
70W, 50V
2
AT eldoLED 0-10v, 0.1% Dimming AD eldoLED DALI, 0.1% Dimming AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)3 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
13W, 9V
25W, 18V
37W, 27V
49W, 35V
61W, 44V
74W, 53V
92W, 50V
* 707 | ZipWave and the 117 series are only available in integral power 1 For Integral power mounting, only one driver is supplied. The two lights can not be operated separately. 2 Philips 1% dimming 3 Only available for 120v 4 Philips 5% dimming Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C | Page 4 of 15
LED Driver Guide Driver Compatibility : Available for either Remote or Integral power housing : Available for only Remote power housing*
Driver compatibility is determined by rail type, output and rail lengths. See the chart below for driver compatibility with your rail section lengths.
Standard Output (SO) with Vode Button Board
12” (305mm)
24” (610mm)
36” (914mm)
48” (1219mm)
60” (1524mm)
72” (1829mm)
96” (2438mm) 2
107 | BoxRail AE eldoLED 0-10v, 1.0% Dimming 107 | WingRail AT eldoLED 0-10v, 0.1% Dimming 117 | K1 BoxRail* 117 | K1 WingRail* AD eldoLED DALI, 0.1% Dimming AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)3 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
7W, 6V
13W, 12V
19W, 18V
26W, 24V
32W, 30V
38W, 36V
51W, 48V 2
AE eldoLED 0-10v, 1.0% Dimming
107 | DoubleBox 117 | K2 BoxRail* AT eldoLED 0-10v, 0.1% Dimming 117 | K2 WingRail* AD eldoLED DALI, 0.1% Dimming
1 1 1
AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)3 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
907 | BoxRail
7W, 6V
13W, 12V
19W, 18V
26W, 24V
32W, 30V
38W, 36V
51W, 48V 2
AE eldoLED 0-10v, 1.0% Dimming AT eldoLED 0-10v, 0.1% Dimming AD eldoLED DALI, 0.1% Dimming AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)3 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
7W, 9V
13W, 12V
19W, 18V
26W, 24V
32W, 30V
38W, 36V
51W, 48V
* The 117 series is only available in integral power 1 For Integral power mounting, only one driver is supplied. The two lights can not be operated separately. 2 Philips 1% dimming 3 Only available for 120v
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C | Page 5 of 15
LED Driver Guide Driver Compatibility : Available for either Remote or Integral power housing : Available for only Remote power housing*
Driver compatibility is determined by rail type, output and rail lengths. See the chart below for driver compatibility with your rail section lengths.
High Output (HO) with Vode Button Board
12” (305mm)
24” (610mm) 1
107 | BoxRail AE eldoLED 0-10v, 1.0% Dimming 107 | WingRail AT eldoLED 0-10v, 0.1% Dimming 117 | K1 BoxRail* 117 | K1 WingRail* AD eldoLED DALI, 0.1% Dimming AX eldoLED DMX, 100-0% dimming
36” (914mm) 1
48” (1219mm) 1
60” (1524mm)
72” (1829mm)
2
2
2
2
96” (2438mm)
AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)3 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
11W, 6V
21W, 12V 1
AE eldoLED 0-10v, 1.0% Dimming
107 | DoubleBox 117 | K2 BoxRail* AT eldoLED 0-10v, 0.1% Dimming 117 | K2 WingRail* AD eldoLED DALI, 0.1% Dimming
32W, 18V 1
42W, 24V 1
53W, 30V
63W, 36V
2
2
2
2
84W, 48V
AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)3 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
907 | BoxRail
11W, 6V
21W, 12V 1
AE eldoLED 0-10v, 1.0% Dimming
32W, 18V 1
42W, 24V 1
53W, 30V
63W, 36V
2
2
4
4
84W, 48V
AT eldoLED 0-10v, 0.1% Dimming AD eldoLED DALI, 0.1% Dimming AX eldoLED DMX, 100-0% dimming AH Lutron Hi-lume 1%, EcoSystem (LDE1) AH2 Lutron Hi-lume 1% 2-wire (LTE)3 AH3 Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Wattage, Voltage
11W, 6V
21W, 12V
32W, 18V
42W, 24V
53W, 30V
63W, 36V
84W, 48V
* The 117 series is only available in integral power 1 OSRAM 10% dimming 2 Philips 1% dimming 3 Only available for 120v 4 Philips 5% dimming Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C | Page 6 of 15
LED Driver Guide Driver Specifications and Wiring Guide
AE: eldoLED 0-10v, 1.0% Dimming Vode uses a variety of drivers to meet the specific requirements of each LED product. Due to the differing wattage or voltage of each rail, different drivers are required in order to properly operate each rail type.
eldoLED ECOdrive Part Number | ECOdrive 366/L Part Number | ECOdrive 566/L Dimming Control: Dimming Range: Dimming Curve: Dimming Type: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature:
0-10 V (isolated) 100% to 1.0% Driver dimming curve is factory preset to linear. Logarithmic is available upon request Analog, hybrid of constant current reduction (CCR) and pulse width modulation (PWM) 30W and 50W Universal 120-277V, 50/60 Hz. Up to 72’ (21.94m) from LED source Constant current, Class 2 12.6” (L) x 1.2” (W) X 1” (H) (320 mm X 30 mm X 26 mm) -20°C to 50°C (-4°F to 122°F)
N L +
To LED
LED output 1 -
ECOdrive
+ AUX -
+ 0-10v -
LEDcode NTC
+ -
DO NOT USE
Philips Xitanium Part Number | XI075C200V054BST1 Dimming Control: Dimming Range: Dimming Curve: Dimming Type: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature:
0-10 V (isolated) 100% to 1.0% Driver dimming curve is factory preset to linear. Logarithmic is available upon request Analog, constant current reduction (CCR) 75W Universal 120-277V, 50/60 Hz. Up to 32’ (9.8m) from LED source Constant current, Class 2 14.17” (L) x 1.18” (W) X 1” (H) (360 mm X 30 mm X 26 mm) -20°C to 50°C (-4°F to 122°F)
PHILIPS
ADVANCE N L
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
XITANIUM 0-10v Dimming
GROUND LINE NEUTRAL
DRIVER
RED (LED+) BLUE (LED-) ORANGE (Rest2) GREEN (SGND) VIOLET (DIM+) GREY (DIM-)
To LED
Revision C | Page 7 of 15
LED Driver Guide Driver Specifications and Wiring Guide
AT: eldoLED 0-10v, 0.1% Dimming Vode uses a variety of drivers to meet the specific requirements of each LED product. Due to the differing wattage or voltage of each rail, different drivers are required in order to properly operate each rail type.
eldoLED SOLOdrive Part Number | SOLOdrive 561/L Dimming Control: Dimming Range: Dimming Curve: Dimming Type: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature:
0-10 V (isolated) 100% to 0.1% Driver dimming curve is factory preset to linear. Logarithmic is available upon request Analog, hybrid of constant current reduction (CCR) and pulse width modulation (PWM) 50W Universal 120-277V, 50/60 Hz. Up to 72’ (21.94m) from LED source Constant current, Class 2 12.6” (L) x 1.2” (W) X 1” (H) (320 mm X 30 mm X 26 mm) -20°C to 50°C (-4°F to 122°F)
N L
To LED
+ LED output 1 -
SOLOdrive
+ LED output 2 -
+ 0-10v -
LEDcode NTC
+ -
DO NOT USE
eldoLED SOLOdrive Part Number | SOLOdrive 1061/M Dimming Control: Dimming Range: Dimming Curve: Dimming Method: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature:
0-10 V (isolated) 100% to 0.1% Driver dimming curve is factory preset to linear. Logarithmic is available upon request Analog, hybrid of constant current reduction (CCR) and pulse width modulation (PWM) 100W Universal 120-277V, 50/60 Hz. Up to 72’ (21.94m) from LED source Constant current, Class 2 15.27” (L) x 1.65” (W) X 1.18” (H) (388 mm X 42 mm X 30 mm) -40°C to 50°C (-40°F to 122°F)
N L
+ LED output 1 -
SOLOdrive
To LED
+ LED output 2 + LED output 3 +
+ 0-10v
LED output 4
0-10v
LEDcode NTC
-
+ -
+ -
DO NOT USE
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C | Page 8 of 15
LED Driver Guide Driver Specifications and Wiring Guide
AD: eldoLED DALI, 0.1% Dimming Vode uses a variety of drivers to meet the specific requirements of each LED product. Due to the differing wattage or voltage of each rail, different drivers are required in order to properly operate each rail type.
eldoLED SOLOdrive Part Number | SOLOdrive 560/L Dimming Control: Dimming Range: Dimming Curve: Dimming Type: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature:
Digital Addressable Lighting Interface (DALI) 100% to 0.1% Driver dimming curve is factory preset to linear. Logarithmic is available upon request. Analog, hybrid of constant current reduction (CCR) and pulse width modulation (PWM) 50W Universal 120-277V, 50/60 Hz. Up to 72’ (21.94m) from LED source Constant current, Class 2 12.6” (L) x 1.2” (W) X 1” (H) (320 mm X 30 mm X 26 mm) -20°C to 50°C (-4°F to 122°F)
N L
To LED
+ LED output 1 -
SOLOdrive
+ LED output 2 -
+ DA -
LEDcode NTC
+
+ -
DA -
DO NOT USE
eldoLED SOLOdrive Part Number | SOLOdrive 1060/M Dimming Control: Dimming Range: Dimming Curve: Dimming Type: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature:
Digital Addressable Lighting Interface (DALI) 100% to 0.1% Driver dimming curve is factory preset to linear. Logarithmic is available upon request Analog, hybrid of constant current reduction (CCR) and pulse width modulation (PWM) 100W Universal 120-277V, 50/60 Hz. Up to 72’ (21.94m) from LED source Constant current, Class 2 15.27” (L) x 1.65” (W) X 1.18” (H) (388 mm X 42 mm X 30 mm) -40°C to 50°C (-40°F to 122°F)
N L
+ LED output 1 -
SOLOdrive
To LED
+ LED output 2 + LED output 3 +
+ 0-10v
LED output 4
0-10v
LEDcode NTC
-
+ -
+ -
DO NOT USE
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C | Page 9 of 15
LED Driver Guide Driver Specifications and Wiring Guide
Philips Xitanium Part Number | XI075C200V054YPT1 Dimming Control: Dimming Range: Dimming Curve: Dimming Type: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature:
Digital Addressable Lighting Interface (DALI) 100% to 5.0% Driver dimming curve is factory preset to linear. Logarithmic is available upon request Analog, constant current reduction (CCR) 75W Universal 120-277V, 50/60 Hz Up to 32’ (9.8m) from LED source Constant current, Class 2 16.6” (L) x 1.2” (W) X 1” (H) (424 mm X 30 mm X 25 mm) -20°C to 50°C (-4°F to 122°F)
PHILIPS
ADVANCE N L
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
XITANIUM 0-10v Dimming
GROUND LINE NEUTRAL
DRIVER
RED (LED+) BLUE (LED-) ORANGE (Rest2) GREEN (SGND) VIOLET (DIM+) GREY (DIM-)
To LED
Revision C | Page 10 of 15
LED Driver Guide Driver Specifications and Wiring Guide
AX: eldoLED DMX 100-0% Dimming Vode uses a variety of drivers to meet the specific requirements of each LED product. Due to the differing wattage or voltage of each rail, different drivers are required in order to properly operate each rail type.
eldoLED POWERdrive Part Number | POWERdrive 561/M Dimming Control: Dimming Range: Dimming Curve: Dimming Type: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature:
Digital Multiplex (DMX) 100% to 0.1% Driver dimming curve is factory preset to linear. Logarithmic or Square is available upon request. Analog, hybrid of constant current reduction (CCR) and pulse width modulation (PWM) 50W Universal 120-277V, 50/60 Hz. Up to 72’ (21.94m) from LED source Constant current, Class 2 17.48” (L) x 1.18” (W) X .83” (H) (444 mm X 29.9 mm X 21 mm) -20°C to 50°C (-4°F to 122°F) -
+
+
4 LED groups
+
N L POWERdrive 561/M
+ + LEDcode / NTC DO NOT USE
DMX in shield DMX in DMX in +
eldoLED POWERdrive Part Number | POWERdrive 1061/M Dimming Control: Dimming Range: Dimming Curve: Dimming Type: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature::
Digital Multiplex (DMX) 100% to 0.1% Driver dimming curve is factory preset to linear. Logarithmic or Square is available upon request. Analog, hybrid of constant current reduction (CCR) and pulse width modulation (PWM) 100W Universal 120-277V, 50/60 Hz. Up to 72’ (21.94m) from LED source Constant current, Class 2 15.27” (L) x 1.65” (W) X 1.18” (H) (388 mm X 42 mm X 30 mm) -40°C to 50°C (-40°F to 122°F) DMX in shield DMX in DMX in +
N L
4 LED groups 4 control channels
POWERdrive 1061/M
+ LEDcode / NTC Ext in Ext in +
DO NOT USE
LedSync out shield LedSync out LedSync out +
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C | Page 11 of 15
LED Driver Guide Driver Specifications and Wiring Guide
AH: Lutron Hi-lume 1%, EcoSystem (LDE1) Vode uses a variety of drivers to meet the specific requirements of each LED product. Due to the differing wattage or voltage of each rail, different drivers are required in order to properly operate each rail type.
Lutron Hi-lume 1% EcoSystem (LDE1) with Soft-on, Fade-to-Black Part Number | LDE Series Dimming Control: Dimming Range: Dimming Type: Wattage: Input Voltage: Remote Distance:
N N/C L N/C N/C E2 E1
N L
+V N/C -V N/C N/CN/C N/C
EcoSystem digital 100% to 1.0% Hybrid of constant current reduction (CCR) and pulse width modulation (PWM) Various Universal 120-277V, 50/60 Hz. Zipper board: Standard Output: 30' (9.14 m), High Output: 15' (4.57 m) Button board: Standard Output: 15' (4.57 m), High Output: 10' (3.05 m) Type: Constant current, Class 2 Dimensions: 14.13” (L) x 1.18” (W) X 1” (H) (359 mm X 30 mm X 25 mm) Operating Temperature: 0°C to 75°C (32°F to 167°F)
LUTRON lutron.com
Hi-lume 1%
To LED
AH2: Lutron Hi-lume 1% 2-wire (LTE) Vode uses a variety of drivers to meet the specific requirements of each LED product. Due to the differing wattage or voltage of each rail, different drivers are required in order to properly operate each rail type.
Lutron Hi-lume 1% 2-Wire (LTE) Part Number | LTE Series Dimming Control: Dimming Range: Dimming Type: Wattage: Input Voltage: Remote Distance:
LUTRON lutron.com
Hi-lume 1%
LTE
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
+V N/C -V
N N/C DL N/C N/CN/C N/C
N DL
N/CN/C N/C
2-Wire (120v forward phase) 100% to 1.0% Constant Current Reduction (CCR) Various 120, 50/60 Hz. Zipper board: Standard Output: 30' (9.14 m), High Output: 15' (4.57 m) Button board: Standard Output: 15' (4.57 m), High Output: 10' (3.05 m) Type: Constant current, Class 2 Dimensions: 14.25” (L) x 1.18” (W) X 1” (H) (362 mm X 30 mm X 25 mm) Operating Temperature: 0°C to 65°C (32°F to 149°F)
To LED
Revision B C | Page 12 of 15
LED Driver Guide Driver Specifications and Wiring Guide
AH3: Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Vode uses a variety of drivers to meet the specific requirements of each LED product. Due to the differing wattage or voltage of each rail, different drivers are required in order to properly operate each rail type.
Lutron Hi-lume 1% EcoSystem/3-Wire (L3D) Part Number | L3D Series Dimming Control: Dimming Range: Dimming Type: Wattage: Input Voltage: Remote Distance:
EcoSystem digital 100% to 1.0% Constant Current Reduction (CCR) Various Universal 120-277V, 50/60 Hz. Zipper board: Standard Output: 30' (9.14 m), High Output: 15' (4.57 m) Button board: Standard Output: 15' (4.57 m), High Output: 10' (3.05 m) Type: Constant current, Class 2 Dimensions: 14.25” (L) x 1.18” (W) X 1” (H) (362 mm X 30 mm X 25 mm) Operating Temperature: 0°C to 65°C (32°F to 149°F)
L
LUTRON lutron.com
E2 E1
Hi-lume 1%
+V N/C -V
N DL
N DL L
N/CN/C N/C
3-Wire Phase Control Wiring
To LED
NOTE: To use 3-Wire Phase Control, remove the provided Gray (E2) and Purple (E1) wires from the driver.
LUTRON lutron.com
E2 E1
Hi-lume 1%
+V N/C -V
L
L
N DL
N
N/CN/C N/C
EcoSystem Digital Wiring
To LED
NOTE: To use EcoSystem, remove the Dimmed Line (DL) orange wire connection from the driver and quick disconnect provided.
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C B | Page 13 of 15
LED Driver Guide Driver Wiring Guide
Driver for All Integral On/Off Switch and Occupancy/Vacancy Sensor Rails The following driver is provided with any rail that has a Vode integral sensor board. (Currently only avalible by request with the 707 | ZipOne and 707 | ZipTwo families). For further information, please contact Vode Customer Service at (707) 996-9898.
eldoLED ECOdrive Part Number | ECOdrive 366/L Part Number | ECOdrive 566/L Dimming Control: Dimming Range: Dimming Curve: Dimming Type: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature:
0-10 V (isolated) 100% to 1.0% Driver dimming curve is factory preset to linear. Logarithmic is available upon request Analog, hybrid of constant current reduction (CCR) and pulse width modulation (PWM) 30W and 50W Universal 120-277V, 50/60 Hz. Up to 72’ (21.94m) from LED source Constant current, Class 2 12.6” (L) x 1.2” (W) X 1” (H) (320 mm X 30 mm X 26 mm) -20°C to 50°C (-4°F to 122°F)
N L + LED output 1 -
ECOdrive
+
To LED
AUX -
+ 0-10v -
LEDcode NTC
+ -
DO NOT USE
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C | Page 14 of 15
LED Driver Guide Driver Wiring Guide
Non-Standard Vode Drivers The following drivers have been tested by Vode and are compatible with our systems, but are only provided by request. If you would like to use one of the following, or another driver, please contact Vode Customer Service (707) 996-9898.
OSRAM Part Number | 79468 (48w) Part Number | 79466 (30w) 0-10 V (isolated) 100% to 10% Driver dimming curve is factory preset to linear Analog, pulse width modulation (PWM) 48w and 30w Universal 120-277V, 50/60 Hz. Up to 16’ (4.88 m) from LED source Constant current, Class 2 11.02” (L) x 1.15” (W) X 1” (H) (280 mm X 29.4 mm X 25.4 mm) -30°C to 50°C (-22°F to 122°F)
OSRAM N L
120-277VAC
Dimming Control: Dimming Range: Dimming Curve: Dimming Method: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature:
Black White Green
Line Neutral GND
To LED
LED+ Red LED- Blue 1400 mA Set Orange PRG/NTC Brown Vaux Out Yellow DIM+ Purple DIM- Grey
eldoLED DUALdrive Part Number | DUALdrive 560/L Dimming Control: Dimming Range: Dimming Curve: Dimming Type: Wattage: Input Voltage: Remote Distance: Type: Dimensions: Operating Temperature:
Digital Addressable Lighting Interface (DALI) 100% to 0.1% Driver dimming curve is factory preset to linear. Logarithmic and/or LightShape are available upon request. Analog, hybrid of constant current reduction (CCR) and pulse width modulation (PWM) 50W* Universal 120-277V, 50/60 Hz. Up to 72’ (21.94m) from LED source Constant current, Class 2 12.6” (L) x 1.2” (W) X 1” (H) (320 mm X 30 mm X 26 mm) -20°C to 50°C (-4°F to 122°F)
N L
+ LED output 1 -
DUALdrive
+ LED output 2 -
+ DA -
LEDcode NTC
+
To LED To LED
+ -
DA -
DO NOT USE *100w version is available if required
Copyright © 2016 Vode Lighting LLC. All rights reserved. Vode Lighting LLC | 1206 East MacArthur, Suite 3, Sonoma, CA 95476 | 707.996.9898
Revision C | Page 15 of 15
