Preview only show first 10 pages with watermark. For full document please download

Drypix Plus (4000) Operation Manual

Rating
Date

October 2018
Size

4.4MB
Views

2,802
Categories

Computers & electronics TVs & monitors Touch screen monitors

Transcript

For Safe Operation PLUS (DRYPIX 4000) Operation Manual 9th Edition: February 2011 Product Overview Basic Operation Care and Maintenance Appendix Maintenance and Inspection This Operation Manual describes how to operate the DRYPIX PLUS (DRYPIX 4000) and cautions to be observed when operating it. Please read the Operation Manual thoroughly before actually operating the DRYPIX PLUS (DRYPIX 4000) After reading this manual, store it nearby the DRYPIX PLUS (DRYPIX 4000) so that you can see it whenever necessary. 897N101792 ii DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Introduction This Operation Manual applies to the following software: • DRYPIX PLUS (DRYPIX 4000) Printer Software V1.0 Fuji Medical Dry Laser Imager DRYPIX PLUS (DRYPIX 4000) is a device that prints digital image data transferred via the DICOM network from the FCR Image Reader or CT, MRI and other imaging modalities onto dedicated film in the selected format. Depending on the intended use, the tray specification can be selected from one-tray, two-tray or three-tray type. This operation manual for the DRYPIX PLUS (DRYPIX 4000) provides detailed explanations of operation methods and cautions to promote proper understanding of functions and more effective usage. We ask that first-time users read this manual thoroughly before actually using the DRYPIX PLUS (DRYPIX 4000). After reading this manual, please store it nearby the DRYPIX PLUS (DRYPIX 4000) so that it may be used to ensure that the machine is used under the best conditions. CAUTIONS 1 No part or all of this manual may be reproduced in any form without prior permission. 2 The information contained in this manual may be subject to change without prior notice. 3 FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from installation, relocation, remodeling, maintenance, and repair performed by other than dealers specified by FUJIFILM Corporation. 4 FUJIFILM Corporation shall not be liable for malfunctions and damages of FUJIFILM Corporation products due to products of other manufacturers not supplied by FUJIFILM Corporation. 5 FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from remodeling, maintenance, and repair using repair parts other than those specified by FUJIFILM Corporation. 6 FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from negligence of precautions and operating methods contained in this manual. 7 FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from use under environment conditions outside the range of using conditions for this product such as power supply, installation environment, etc. contained in this manual. 8 FUJIFILM Corporation shall not be liable for malfunctions and damages resulting from natural disasters such as fires, earthquakes, floods, lightning, etc. Process waste correctly, as stipulated by local law or any regulations that apply. The LCD display lamps in this product contain mercury, which must be recycled or disposed of in accordance with local, state, or federal laws. Caution : Rx Only in the United States (Federal law restricts this device to sale by or on the order of a physician.) Trademark FCR is a trademark or a registered trademark of FUJIFILM Corporation. Open-Source Software Used in This Product The DRYPIX 4000 uses Vx Works. Copyright of Vx Works belongs to Wind River Systems, Inc. The DRYPIX 4000 uses Windows® XP. Windows® XP is the registered trademark of US Microsoft Corporation in the U. S. A. and other countries. Windows® is the registered trademark of US Microsoft Corporation in the U. S. A. and other countries. All other company names and product names described in this manual are the trademarks or registered trademarks of their respective holders. Copyright © 2005-2011 FUJIFILM Corporation. All rights reserved. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 iii iv DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Contents at a Glance Chapter Chapter Chapter Chapter 1 2 3 4 Appendix For Safe Operation This chapter presents Warnings and Cautions we wish you to observe for the safe operation of this equipment. Product Overview This chapter presents overview and major features of this equipment. Basic Operation This chapter describes routine operation procedures, including how to start up/ shut down this equipment and also how to replace a film pack. Care and Maintenance This chapter describes daily care and maintenance we wish you to perform so that you can use the equipment optimally. Appendix A Specifications This chapter presents major specifications of this equipment. Maintenance and Inspection DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 v How to Read This Manual Basic page configuration Please have a good grasp of the basic page configuration of this Operation Manual, as illustrated below, for you to use it more efficiently. Section title Lead Shows the title of an operation procedure described in the section. Describes information we wish you to know in advance of your operating the system or information that may help you to operate it. 3.2 Replacing the Film Pack Index When the film in the supply tray runs out, the Status Lamp goes blinking orange. Have the Fuji Medical Dry Laser Imager DI-HL, DI-HLc, or DI-ML film ready for use. A tutorial animation appears in the display to guide you to replace the film pack. 1 Touch [STOP ALARM] on the Operation Panel. 3 A caption that facilitates you to open a desired [Chapter] quickly. Pull the tray out carefully (1.), and remove the protective material together with the film cushioning cardboard (2.). Discard the removed protective material and film cushioning cardboard. Touch. Film cushioning cardboard Operation procedure Protective material 3 2. Remove. HINT In the following cases, start operating from step 2 below. • For an equipment unit where the alarm has been set to be silent. • For an equipment unit where films of the same size are supplied automatically from the other tray, when the film runs out. 2 Touch [UNLOCK TRAY] on the Operation Panel. Basic Operation Describes an operation procedure according to sequential numbers. 1. Pull out. 4 Load a new film pack so that its red label or green label (marked with an arrow) and the arrow mark on the tray match with each other. Operation steps are presented in the illustration following specified order. Multiple sub-steps that consist of an operation step is numbered, 1., 2. ..... Tray side Film pack side The arrow marks must be aligned neatly with each other. Touch. The tray will be unlocked. CAUTIONS Be sure to pull the tray out only after it has been unlocked. Otherwise, a system malfunction will result. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 3-3 Page number Displayed in conjunction with the chapter number. vi DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Illustrated operation procedure Marks Information items to be observed when you are operating this system and the supplementary remarks are described in this manual with the respective marks. For the safe system operation, be sure to observe Warning/Caution. Indicates hazardous situations that may lead to serious injury or even death if the precaution is not or could not be followed. WARNING Indicates hazardous situations that may lead to mild or moderate injury or physical damages if the caution is not or cannot be followed. CAUTIONS HINT Indicates information that may be helpful. Expressions Names of keys displayed on the touch panel, windows, and messages are as follows. ● Touch keys (example) ------------------------------- [Utility] ● Windows (example) ----------------------------- “DRYPIX 4000 Initial screen” ● Messages (example) ----------- Graphics How to operate the system is shown with a specific instruction, such as Touch. . An operation requiring you to touch two or more buttons is displayed with serial numbers, such as (1. Select.), (2. Touch.), …, to show order of its operation. 1. Select. 2. Touch. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 vii Contents Introduction�� iii Contents at a Glance�� v How to Read This Manual�� vi Chapter 1 For Safe Operation 1.1 Precautions Before Operating This Equipment�� 1-1 1.2 Safety�� 1-2 1.3 Electromagnetic Compatibility (EMC)��1-4 1.4 Locations of labels and signs�� 1-8 1.4.1 Locations��1-8 1.4.2 Safety and Other Signs�� 1-11 1.5 Precautions on DRYPIX4000 Operations�� 1-12 1.5.1 Precautions for Use�� 1-12 1.5.2 Precautions When Outputting Film Prints�� 1-12 1.5.3 Precautions for Storing or Handling the DI-HL, DI-HLc, and DI-ML Films Used for the Fuji Medical Dry Laser Imager�� 1-14 Chapter 2 Product Overview 2.1 Features of the DRYPIX4000�� 2-1 2.2 Units Names and the Functions�� 2-2 2.2.1 DRYPIX4000 Main Unit��2-2 2.2.2 Operation Panel��2-4 Chapter 3 Basic Operation 3.1 Starting / Shutting Down the Equipment�� 3-1 3.1.1 3.1.2 Starting the Equipment��3-1 Shutting Down the Equipment��3-2 3.2 Replacing the Film Pack��3-3 3.3 Checking Order of Film Prints��3-5 3.4 Changing Order of Film Prints��3-6 3.5 Viewing Details of Print Jobs�� 3-7 3.6 Deleting Print Jobs��3-9 Chapter 4 Care and Maintenance 4.1 Cleaning the Inside and Surroundings of the Equipment�� 4-1 4.1.1 4.1.2 Washing the Cleaning Roller with Water��4-2 Cleaning the Inside and Surroundings of the Equipment�� 4-4 4.2 Users Checksheet (Care and Maintenance)�� 4-7 4.3 About Preventive Maintenance��4-8 Appendix A Specifications A.1 Specifications��A-1 A.2 External View and Weight�� A-2 Maintenance and Inspection viii DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Chapter 1 For Safe Operation 1.1 Precautions Before Operating This Equipment 1 For Safe Operation Before using this equipment, please read “Precautions Before Operating This Equipment” carefully so that you can operate it correctly. Whenever you operate this equipment, be sure to observe those precautions. Failure to do so may cause you to subject to injuries or property damage to occur. This system is classified as a medical device under EC Directive 93/42/EEC. This equipment has been designed on the assumption that the patient would not come into direct contact with it or for operation by appropriately trained operator. Process waste correctly, as stipulated by local law or any regulations that apply. When discarding the DRYPIX 4000 that incorporates the lithium battery, be sure to contact a licensed waste disposal contractor because it cannot be disposed of as a general waste. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 1-1 1.2 Safety Before using the DRYPIX 4000, read this section thoroughly to ensure that you use the product properly. 1 Laser Handling Precautions For Safe Operation This equipment is a Class 1 laser product (IEC 60825-1: 2007). This device contains an embedded laser with the following specification: Class : 3B Medium : Semiconductor laser Wavelength : 658nm Maximum output : 70mW (CW) Beam divergence : 20° WARNING To prevent the user from being exposed to laser beams, always observe the following precautions. ● Never remove any covers other than the Small Upper Cover and Lower Front Cover of the equipment. ● When opening covers for coping with film jams, strictly observe procedures set forth in the Operation Manual. Never perform any other procedures. ● Always contact Fujifilm service personnel immediately if a malfunction is suspected in the equipment. CAUTIONS Use of controls or adjustment or performance of procedures other than those specified herein may result in hazardous radiation exposure. Electric Shock Warnings WARNING The power supply to the DRYPIX 4000 equipment is AC100-120V/AC200-240V. To avoid electric shocks, users should always take the following precautions: ● Install the printer in a location where it will not be exposed to water. ● Check that the printer is securely earthed. ● Check that all of the cords and cables are completely and securely connected. WARNING Never remove the printer cover. The printer contains high-voltage components that could cause an electric shock. 1-2 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Precaution about High Temperature CAUTIONS Be careful with units where High-temperature Caution Labels are affixed as those units may be hot during operation. 1 Classification For Safe Operation 1) According to the type of protection against electric shock CLASS 1 EQUIPMENT 2) According to the degree of protection against electric shock NO APPLIED PART 3) Protection against harmful ingress of water IPXO 4) According to the degree of safety of application in the presence of a flammable anesthetics mixture with air or with oxygen or nitrous oxide. Equipment not suitable for use in the presence of a flammable anesthetics mixture with air or with oxygen or nitrous oxide. 5) According to the mode of operation CONTINUOUS OPERATION DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 1-3 1.3 Electromagnetic Compatibility (EMC) This equipment has been tested and found to comply with the limits for medical devices to the IEC 60601-1-2:2001+A1:2004 (EN60601-1-2:2001+A1:2006), Medical Device Directive 93/42/EEC. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to other devices, which can be determined by tuning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures: • Reorient or relocate the receiving device. • Increase the separation between the equipment. • Connect the equipment into an outlet on a circuit different from that to which the other device(s) are connected. Consult the manufacturer or field service technician for help. 1 For Safe Operation Further information for IEC 60601-1-2 (EN60601-1-2) • Medical electrical equipment needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in the accompanying documents. • Portable and mobile RF communications equipment can affect medical electrical equipment. • Information regarding the cable affecting EMC is as follows. Name General Speciﬁcation I/F Cable TIA/EIA-568 Cat5 or more. Straight cable of UTP type. • The use of accessories, transducers and cables other than those specified, with the exception of transducers and cables sold by FUJIFILM Corporation as replacement parts for internal components, may result in increased emissions or decreased immunity of the DRYPIX 4000. • The DRYPIX 4000 should not be used adjacent to or stacked with other equipment. If adjacent or stacked use is necessary, the DRYPIX 4000 should be observed to verify normal operation in the configuration in which it will be used. Guidance and manufacturer’s declaration - electromagnetic emissions The DRYPIX 4000 is intended for use in the electromagnetic environment specified below. The customer or the user of the DRYPIX 4000 should assure that it is used in such an environment. Emissions test RF emissions CISPR 11 RF emissions CISPR 11 Harmonic emissions IEC61000-3-2 Voltage fluctuations/ flicker emissions IEC61000-3-3 1-4 Compliance Group 1 Electromagnetic environment - guidance The DRYPIX 4000 uses RF energy only for its internal function. Therefore, its RF emissions are very low and are not likely to cause any interference in nearby electronic equipment. Class A Class A Complies DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 The DRYPIX 4000 is suitable for use in all establishments other than domestic and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes. Guidance and manufacturer’s declaration - electromagnetic immunity The DRYPIX 4000 is intended for use in the electromagnetic environment specified below. The customer or the user of the DRYPIX 4000 should assure that it is used in such an environment. Immunity test IEC 60601 test level Compliance level Electromagnetic environment guidance Electrostatic discharge (ESD) IEC61000-4-2 ±6kV contact ±8kV air Electrical fast transient/burst IEC61000-4-4 ±2kV for power supply lines ±1kV for input/output lines ±2kV contact ±4kV contact ±6kV contact ±2kV air ±4kV air ±8kV air ±2kV for power supply lines ±1kV for input/output lines Surge IEC61000-4-5 ±1kV differential mode ±2kV common mode ±1kV differential mode ±2kV common mode Mains power quality should be that of a typical commercial or hospital environment. Voltage dips, short interruptions and voltage variations on power supply input lines IEC61000-4-11 <5% UT (>95% dip in UT) for 0.5 cycle 40% UT (60% dip in UT) for 5 cycles 70% UT (30% dip in UT) for 25 cycles <5% UT (>95% dip in UT) for 5 s <5% UT (>95% dip in UT) for 0.5 cycle 40% UT (60% dip in UT) for 5 cycles 70% UT (30% dip in UT) for 25 cycles <5% UT (>95% dip in UT) for 5 s Mains power quality should be that of a typical commercial or hospital environment. If the user of the DRYPIX 4000 requires continued operation during power mains interruptions, it is recommended that the DRYPIX 4000 be powered from an uninterruptible power supply or a battery. 3 A/m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment. 3 A/m For Safe Operation Power frequency (50/60Hz) magnetic fieldIEC61000-4-8 1 Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%. Mains power quality should be that of a typical commercial or hospital environment. NOTE: UT is the a.c. mains voltage prior to application of the test level. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 1-5 Guidance and manufacturer’s declaration - electromagnetic immunity The DRYPIX 4000 is intended for use in the electromagnetic environment specified below. The customer or the user of the DRYPIX 4000 should assure that it is used in such an environment. Immunity test 1 IEC 60601 test level Compliance level Electromagnetic environment - guidance For Safe Operation Conducted RF IEC61000-4-6 3 Vrms 150 kHz to 80 MHz 3 Vrms Portable and mobile RF communications equipment should be used no closer to any part of the DRYPIX4000, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. Radiated RF IEC61000-4-3 3 V/m 80 MHz to 2.5 GHz 3 V/m Recommended separation distance d = 1.2 d = 1.2 80 MHz to 800 MHz d = 2.3 800 MHz to 2.5 GHz where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer and d is the recommended separation distance in metres (m). Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey,a should be less than the compliance level in each frequency range.b Interference may occur in the vicinity of equipment marked with the following symbol: NOTE 1: At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. a Field strength from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the DRYPIX 4000 is used exceeds the applicable RF compliance, the DRYPIX 4000 should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the DRYPIX 4000. b Over the frequency range 150 kHz to 80 MHz, field strength should be less than 3 V/m. 1-6 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Recommended separation distances between Portable and mobile RF communications equipment and the DRYPIX 4000 The DRYPIX 4000 is intended for use in the electromagnetic environment in which radiated RF disturbances are controlled. The customer or the user of the DRYPIX 4000 can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the DRYPIX 4000 as recommended below, according to the maximum output power of the communications equipment. 0.01 0.1 1 10 100 150 kHz to 80 MHz d = 1.2 0.12 0.38 1.2 3.8 12 80 MHz to 800 MHz d = 1.2 0.12 0.38 1.2 3.8 12 800 MHz to 2.5 GHz d = 2.3 0.23 0.73 2.3 7.3 23 For Safe Operation 1 Separation distance according to frequency of transmitter m Rated maximum output power of transmitter W For transmitters rated at a maximum output power not listed above, the recommended separation distance d in metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies. NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 1-7 1.4 Locations of labels and signs Locations of labels and signs affixed to the DRYPIX 4000, and the relevant safety signs are shown below. 1.4.1 Locations 1 For Safe Operation Class 3B Panel Label #2 Rating Label (#1/#2/#3/#4) HHS Certification and Identification Label (#1/#2) Caution Label 1 (LAN connector) Class 3B Panel Label #1 Year of Manufacture and EFUP (Environmentally Friendly Use Period) Label Mercury-containing Products Label Caution Label 1 Watch out Hand Caution Label High-temperature Caution Label Class 3B Panel Label #2 High-temperature Caution Label 1-8 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Pattern A Pattern B 1 Rating Label #3 Rating Label #2 Rating Label #4 HHS Certification and Identification Label #1 HHS Certification and Identification Label #2 DRYPIX PLUS (DRYPIX 4000) Operation Manual For Safe Operation Rating Label #1 897N101792 1-9 1 For Safe Operation Class 3B Panel Label #1 Be aware that the temperature may be high in the area where the following label is affixed. Be sure to use the power cord our official dealer or local presentative provided. Caution Label 1 High-temperature Caution Label Do not connect a telephone wire to the LAN connector. Always use a LAN cable recommended under the IEC60950/UL60950 standard. Caution Label (LAN connector) Be careful not to catch fingers when closing the cover. Mercury-containing Products Label Watch out Hand Caution Label Sample year of manufacture Year of Manufacture and EFUP (Environmentally Friendly Use Period) Label Class 3B Panel Label #2 1-10 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 1.4.2 Safety and Other Signs The following safety signs are used in the DRYPIX 4000 labels or on its body. Sign Description This symbol indicates compliance of the equipment with Directive 93/42/EEC. 1 Attention, consult ACCOMPANYING DOCUMENTS. For Safe Operation High-temperature caution Power-OFF Power-ON Protective grounding (to the earth) Alternating current This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2002/96/EC) and your national law. This product should be handed over to a designated collection point. Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about waste, please contact FUJIFILM dealers. Year of manufacture Environmentally Friendly Use Period (EFUP) Stand-by switch Utility button DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 1-11 1.5 Precautions on DRYPIX 4000 Operations Printout on film is enabled from DICOM-networked modalities. Therefore, no specific operation is required for printout on film for the DRYPIX 4000 system. 1.5.1 Precautions for Use 1 CAUTIONS For Safe Operation If you press and hold the Power ON Switch (for 4 seconds or longer) when the equipment is up and running, it will be shut down forcibly. This also occurs even when the equipment is in process of image printout or in Utility mode. CAUTIONS Do not get on the equipment or place any object on it. Otherwise, equipment breakage or human injury may result. CAUTIONS Do not put weight on the film tray pulled out. CAUTIONS When using the shutter, be careful and hold it firmly with both hands to prevent it from dropping. CAUTIONS Be sure to turn the power OFF first and then insert the shutter, because a system error may result. Note, however, that you do not have to turn the power OFF if an instruction is indicated on the Operation Panel to insert the shutter. 1.5.2 Precautions When Outputting Film Prints WARNING If the power to the DRYPIX 4000 is shut down unintentionally, image printouts may not be generated. We, therefore, recommend that you do not erase images stored on the FCR Image Reader and other modalities, such as CT, MRI, and the like, before you make sure that images have been printed properly. FUJIFILM Corporation and authorized dealers will not assume any responsibility for loss of images and others. CAUTIONS Do not forcibly remove a film in process of ejection. Removing a film in process of ejection forcibly may damage it. 1-12 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 CAUTIONS Do not open while in processing any of the Upper Front Cover, Upper Right-side Cover, Lower Right-side Cover and Small Upper Cover. If a cover is opened while in processing, any image being processed at the moment will be disabled because correct print density cannot be obtained. If a cover is opened while in processing, the equipment will stop operating for the safety reason. A message also appears on the Operation Panel at this time, indicating that a cover is open. 1 For Safe Operation HINT A maximum of 150 films can be stacked in the output film tray. Remove the output films before the film tray becomes full. HINT Install this equipment in a well-ventilated place. HINT If there still remain unprocessed films in the equipment, a confirmation window like that shown on the right will open. Touch [AFTER PRINT] or [IMMEDIATELY]. If you touch [IMMEDIATELY], unprocessed image data will remain inside the equipment and will be output after it is rebooted the next time. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 1-13 1.5.3 Precautions for Storing or Handling the DI-HL, DI-HLc, and DI-ML Films Used for the Fuji Medical Dry Laser Imager Precautions for storing or handling unused films 1 Use only the “Fuji Medical Dry Laser Imager Film DI-HL, DI-HLc, or DI-ML” that is compatible with this equipment. If a film other than DI-HL, DI-HLc, or DI-ML is used, a malfunction may be caused to the equipment. 1 For Safe Operation 2 Be sure to store unused films contained in the film pack in a cool, dry and dark place of low temperature and low humidity (temperature: 10 to 23ºC, relative humidity: 45±15%), avoiding radioactivity and reactive gases, same as for the conventional wet-type film. 3 The DI-HL, DI-HLc, and DI-ML films are light-sensitive. Do not open a film pack before it is loaded properly in the equipment. 4 Do not touch unused films with bare hands, otherwise adverse effects can appear on recorded images. 5 Do not take unused films out of the film pack that has once been loaded into the equipment and opened or add films to the film pack loaded, which will result in misoperation or failure of the equipment. 6 The film pack contains a protective sheet, in addition to the specified number of recording films. This protective sheet will remain in the film pack even after those recording films have been printed and it cannot be used for image recording. Because the protective sheet is a film, discard it appropriately together with other used films. Precautions for storing or handling recorded films 1 Store recorded films in a cool, dry and dark place of low temperature and low humidity. The higher the temperature and humidity, the more the density of recorded images will change sharply. Longterm storage at high temperature, high humidity and/or daylight conditions, such as in a car or room during summer, may cause discoloration. Using films in the slide projector or overhead projector will also cause discoloration. 2 For the long-term storage performance of recorded films, we assume based on the result of the acceleration test that it will be over 30 years at the storage temperature of 25ºC and over 25 years at 30ºC, until the portion on an image of density (D) = 1.2 at time of output to change 10% (ΔD=0.12). 3 After an image has been recorded, the film immediately after it was ejected from the machine is still in the process of image development and the room illumination or light emanating from the viewing box will cause slight changes in the optical density. Due to such optical effect, traces of overlapped films or transferred images can be visually recognized temporarily, which will disappear when those films are left under the normal light condition. 4 Note that lucid surfaces of recorded films can be lost or traces of contact with any chemicals that contain water, alcohol, developer, etc., and with other objects that contain a large amount of salt may appear on images, if they are handled under high-humidity environment or due to such undesirable contacts. 5 Do not store films with its image recording faces attached directly for preventing them from sticking to each other. 1-14 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Chapter 2 Product Overview 2.1 Features of the DRYPIX 4000 This section describes the main features of the Fuji Medical Dry Laser Imager DRYPIX 4000. ● This equipment adopts a system that records images with the laser and develops them by means of thermal processing, doing away with the need for management or replenishment of processing chemicals and disposal of waste solutions. This equipment thus uses an environment-friendly system. ● Film can be handled under daylight room conditions, doing away with the need for darkrooms. ● A color LCD touch panel used in the Operation Panel enables simplified easy-to-view operations. Moreover, you can check the equipment status by means of Status Lamp even if you are away from the equipment. ● You can set up power saving mode to save power consumption of the equipment. ● When a film jams, you can correct it by opening covers as necessary. 897N101792 Product Overview DRYPIX PLUS (DRYPIX 4000) Operation Manual 2 2-1 2.2 Units Names and the Functions This section names each of the DRYPIX 4000 components and explains their functions. 2.2.1 DRYPIX 4000 Main Unit 2 Product Overview Rear Front Name 2-2 Function Operation Panel Shows power supply or equipment status by means of various lamps. This panel can be operated also by touching the on-screen buttons and icons. Upper Front Cover Open this cover when a film jam occurs inside the equipment, and take appropriate actions to correct film jamming. Tray 1 A film pack containing new films is loaded here. Note that basically this tray is locked. To open this tray, press [UNLOCK TRAY] on the Operation Panel to unlock it. Tray 2 (option) A film pack containing new films is loaded here. Note that basically this tray is locked. Tray 3 (option) A film pack containing new films is loaded here. Note that basically this tray is locked. Lower Front Cover Open this cover when cleaning the air filter. Main Power Switch Basically leave this switch turned ON ( I ). ON ( I ) : Main Power ON OFF ( O ) : Main Power OFF Small Upper Cover Open this cover when a film jam occurs inside the equipment, and take appropriate actions to correct film jamming. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Upper Right-side Cover Open this cover when a film jam occurs inside the equipment, and take appropriate actions to correct film jamming. Open this cover also when cleaning the cleaning roller. Lower Right-side Cover Open this cover when a film jam occurs inside the equipment, and take appropriate actions to correct film jamming. Film Sorter (3 bins) The optionally provided Film Sorter that sorts films by each film size and then ejects them appropriately. LAN Connector Connected to the image network devices. 10base-T/100base-TX Interface CAUTIONS 2 Never open trays or covers during processing. Product Overview CAUTIONS When closing covers, be careful not to pinch your finger in the aperture. CAUTIONS Do not connect telephone lines to LAN connector. Only theIEC950/UL1950 standard cables are appropriate for connecting to this connector. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 2-3 2.2.2 Operation Panel 2 Product Overview Name 2-4 Function Power ON Switch Turns ON the power to the main unit. Power Lamp Lights green when the Main Power Switch turns ON. As the Main Power Switch is basically left turned ON, the Power Lamp will also remain lit constantly. Status Lamp Indicates the equipment status. When lighting green : Film printout is enabled. When blinking green : In process of system startup or recovery from an error condition. When blinking orange : No films remaining in the tray, a film jam or any other errors. Power Save Lamp Indicates that the equipment is in Sleep Mode. Blinking (Screen erasure) : A window closes. Blinking (Power saving) : Closes a window, have the heater go into power save mode, or turns the motor power OFF. Lighting (Sleep mode) : Closes a window, stops working the heater, or turns the motor power OFF. Unlit (In routine operation) : At the press of an icon or a button, the equipment can be operated. Display Equipment status and the number of films remaining in each tray are displayed here. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Chapter 3 Basic Operation 3.1 Starting / Shutting Down the Equipment 3.1.1 Starting the Equipment 1 2 Touch the Power ON Switch on the Operation Panel. Make sure that the Power Lamp on the Operation Panel lights green, with the Main Power Switch turned ON at the bottom front of the main unit. Turn the Main Power Switch ON if it is not in the ON status. 3 Press. Basic Operation HINT Power Lamp When the “Ready Starting up…” message appears on the Operation Panel, this equipment is ready to receive images from other devices. 3 Press. When the equipment is up and running, “Ready” appears on the Operation Panel. Main Power Switch CAUTIONS If the Main Power Switch is set to the “ | ” side, it is in the ON status. CAUTIONS If you press and hold the Power ON Switch (for 4 seconds or longer) when the equipment is up and running, it will be shut down forcibly. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 3-1 3.1.2 Shutting Down the Equipment 1 Touch [SHUTDOWN] on the Operation Panel. Touch. 3 2 Touch [YES] on the window asking if you wish to shut down the system. Basic Operation Touch. The equipment shuts down when the screen display goes off after the “System terminating…” message appears. CAUTIONS If you want to reboot the equipment, wait for about 10 seconds or longer after the equipment has been shut down, and then touch the Power ON Switch. This is to fully reset the system status inside the equipment. 3-2 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 3.2 Replacing the Film Pack When the film in the supply tray runs out, the Status Lamp goes blinking orange. Have the Fuji Medical Dry Laser Imager DI-HL, DI-HLc, or DI-ML film ready for use. A tutorial animation appears in the display to guide you to replace the film pack. 1 Touch [STOP ALARM] on the Operation Panel. 3 Pull the tray out carefully (1.), and remove the protective material together with the film cushioning cardboard (2.). Discard the removed protective material and film cushioning cardboard. Touch. Film cushioning cardboard Protective material 3 2. Remove. In the following cases, start operating from step 2 below. • For an equipment unit where the alarm has been set to be silent. • For an equipment unit where films of the same size are supplied automatically from the other tray, when the film runs out. 2 Touch [UNLOCK TRAY] on the Operation Panel. Basic Operation HINT 1. Pull out. 4 Load a new film pack so that its red label or green label (marked with an arrow) and the arrow mark on the tray match with each other. Tray side Film pack side The arrow marks must be aligned neatly with each other. Touch. The tray will be unlocked. CAUTIONS Be sure to pull the tray out only after it has been unlocked. Otherwise, a system malfunction will result. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 3-3 5 Raise one end of the film pack to tear off the label (1.), and open both ends of the film pack (2.), as illustrated. 7 Slowly push the film tray in until it locks firmly. When the tray locks firmly, a beep will sound. 1. Tear off the label. Push in slowly. CAUTIONS 3 When closing the tray, be careful not to pinch your fingers. Basic Operation 2. Open both ends. 8 Gently and slowly pull out straight toward you one film pack end that is outside the film tray. The display returns to the DRYPIX 4000 initial screen. This completes the film supply procedure. 6 Use the cutter stored on the right-hand side of the Operation Panel (1.) to cut the film pack along the tray edge (2.). Replace then the cutter in the position where it has been stored (3.). 1. Take out. Cutter 3. Replace. Pull out. CAUTIONS An attempt to pull the film pack out at a slant or roughly will cause it to break. HINT When you have selected “By each film pack” for “AUTOMATED F.D.C.” in the Utility mode, the Auto F.D.C. (automatic film density calibration) would be performed. After completion of the density calibration procedure, the display returns to the DRYPIX 4000 initial screen. Note that the number of films contained in the tray where a new film pack was loaded has changed. 2. Cut. CAUTIONS If the cutter’s blade protection is broken, the blade will be exposed posing then danger to the user. Do not touch the unprotected blade. Replace a dull cutter hard to cut the film pack, as necessary. 3-4 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 3.3 Checking Order of Film Prints You can display already-registered print jobs as follows to check order of film prints. 1 Touch the [Hard Disk] icon on the Operation Panel. 2 After checking order of film prints, touch [QUIT]. Touch. Touch. HINT The display returns to the DRYPIX 4000 initial screen Basic Operation The display changes to the “Job List” screen. 3 Films are printed successively starting from the job that is on the top of the “Job List”. To display the updated print job information, touch [REFRESH]. Touch. AE Title Shows the name of a connected device. Entry Shows the date and time when an image was received from the connected device. Status • Printing : Shows a job being in process of printout. • Processing : Shows a job being in process of image processing or awaiting printout. • Blank : Shows an unprocessed job. • Error : Shows a job with which an error occurred. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 3-5 3.4 Changing Order of Film Prints You can output specific already-registered print jobs on film urgently, as follows. 1 Touch the [Hard Disk] icon on the Operation Panel. 2 Use [] and [] to select a specific job (1.), and touch [URGENT PRINT] (2.). 1. Select. Touch. 2. Tocuh. 3 Basic Operation The display changes to the “Job List” screen. Touching [URGENT PRINT] will move the selected job to the top of unprocessed jobs, which will then be printed urgently HINT Films are printed successively starting from the job that is on the top of the “Job List”. To display the updated print job information, touch [REFRESH]. CAUTIONS This operation is possible only when the relevant Status item is blank. (Order of image data printout jobs in the “Printing” or “Processing” status cannot be changed.) 3 Touch [QUIT]. Touch. 3-6 AE Title Shows the name of a connected device. Entry Shows the date and time when an image was received from the connected device. Status • Printing : Shows a job being in process of printout. • Processing : Shows a job being in process of image processing or awaiting printout. • Blank : Shows an unprocessed job. • Error : Shows a job with which an error occurred. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Touch. The display returns to the DRYPIX 4000 initial screen. 3.5 Viewing Details of Print Jobs You can view details of already-registered print jobs, as follows. 1 Touch the [Hard Disk] icon on the Operation Panel. 2 Use [] and [] to select a job (1.), and touch [DETAIL] (2.). 1. Select. Touch. 2. Touch. 3 HINT Films are printed successively starting from the job that is on the top of the “Job List”. To display the updated print job information, touch [REFRESH]. The “DETAIL” screen then opens. 3 Basic Operation The display changes to the “Job List” screen. Touch [] and [] to view other jobs, as necessary. Select. Touch. 4 AE Title Shows the name of a connected device. Entry Shows the date and time when an image was received from the connected device. Status • Printing : Shows a job being in process of printout. • Processing : Shows a job being in process of image processing or awaiting printout. • Blank : Shows an unprocessed job. • Error : Shows a job with which an error occurred. After viewing print job details, touch [QUIT]. Touch. The display returns to the “Job List” screen. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 3-7 5 Touch [QUIT] on the “Job List” screen. Touch. The display then returns to the DRYPIX 4000 initial screen. 3 Basic Operation 3-8 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 3.6 Deleting Print Jobs You can delete already-registered print jobs as follows. 1 Touch the [Hard Disk] icon on the Operation Panel. 2 Use [] and [] to select a job (1.), and touch [DELETE] (2.). 1. Select. Touch. 2.Touch. HINT Films are printed successively starting from the job that is on the top of the “Job List”. To display the updated print job information, touch [REFRESH]. A confirmation window opens. If [YES] is touched on the conformation screen that opens, a job selected as above will be deleted. If [NO] is touched, the display returns to the “Job List” screen. Basic Operation The display changes to the “Job List” screen. 3 Touch. CAUTIONS AE Title Shows the name of a connected device. Entry Shows the date and time when an image was received from the connected device. Status • Printing : Shows a job being in process of printout. • Processing : Shows a job being in process of image processing or awaiting printout. • Blank : Shows an unprocessed job. • Error : Shows a job with which an error occurred. If a print job is deleted, the relevant images will also be deleted. CAUTIONS This operation is possible only when the relevant Status column is blank. (Order of image data printout jobs in the “Printing” or “Processing” status cannot be changed.) DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 3-9 3 Touch [QUIT] on the “Job List” screen. Touch. The display returns to the DRYPIX 4000 initial screen. 3 Basic Operation 3-10 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Chapter 4 Care and Maintenance 4.1 Cleaning the Inside and Surroundings of the Equipment Clean the equipment by removing dirt or dust on it. ① Operation Panel Cleaning roller (Optional) (see “4.1.1”) 4 ② Tray Care and Maintenance ③ Front air filter ④ Right side air filter ①∼④（See “4.1.2”） DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 4-1 4.1.1 Washing the Cleaning Roller with Water We recommend that you wash the cleaning roller with water once every week to secure print image quality. When white spots or traces of lint appear on output films, also wash the cleaning roller with water following the procedure described herein. 1 3 Open the Conveyance Unit Cover (1.) to remove the cleaning roller (2.). 1. Open. Make sure that no film recording or output processing is being performed, and then shut the system down. 2. Remove. Cleaning roller CAUTIONS When removing the cleaning roller, hold it with both hands being careful not to drop it on the floor. Touch. 4 4 Wash the cleaning roller with water. Care and Maintenance While splashing water onto the cleaning roller, rub the surface gently to clean. CAUTIONS An error may occur if procedural steps that follow are performed without shutting down the system. Wash. 2 Open the Upper Right-side Cover. CAUTIONS Open. Upper Right-side Cover 4-2 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 If the cleaning roller is rubbed roughly to removing stubborn dirt or dust adhered to the surface and that does not come off only with water, the roller surface may be damaged. If white spots still appear on output films even after it has been water-washed, it is time to replace the cleaning roller for a new one. Replace the cleaning roller around every three years. 5 Use a gauze moistened with alcohol (ethanol anhydride) to wipe off water remaining on the cleaning roller. (The cleaning roller will be dried in a few minutes.) Wipe off. Gauze CAUTIONS Dry the cleaning roller sufficiently, otherwise correct film density may not be obtained or unevenness may appear on an output film. Restore the cleaning roller (1.), and close the Conveyance Unit Cover (2.). Care and Maintenance 6 4 2. Close. 1. Restore. 7 Close the Upper Right-side Cover. Close. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 4-3 4.1.2 Cleaning the Inside and Surroundings of the Equipment Clean each unit of the equipment once every three months, following the procedures described below. Cleaning the Operation Panel 1 Use a cleaner for LCD or the like to wipe off the panel display and then wipe it off with a dry cloth. Cleaning a tray Clean a tray when, for instance, replacing a film pack. 1 Open a tray. Operation Panel Open. 4 CAUTIONS Care and Maintenance Wipe off the cleaner or the like completely. 2 Use a vacuum cleaner or a cloth moistened with water to clean the tray. CAUTIONS Do not use ethanol. If ethanol is impregnated into the barcode reader filter, it can be damaged. 3 Load a new film pack so that its red label (DI-HL or DI-HLc) or green label (DI-ML) (marked with an arrow) and the arrow mark on the tray match with each other. Match arrows with each other. or details of procedures hereafter, see F “Replacing the Film Pack” under chapter 3. 4-4 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Cleaning the front air filter 1 Dismount the Lower Front Cover. Cleaning the right-side air filter 1 Dismount the right-side air filter (1.), and clean it with a vacuum cleaner or the like (2.). 2. Clean. Lower Front Cover 1. Dismount. Dismount. Right-side air filter 2 Slide the front air filter to dismount it (1.), and clean dust or dirt with a vacuum cleaner or the like (2.). 2 Remount the right-side air filter. 4 1. Dismount. Remount. Care and Maintenance Front air filter 2. Clean. 3 Right-side air filter Restore the air filter (1.), and remount the Lower Front Cover (2.). 1. Restore. 2. Remount. CAUTIONS When remounting the cover, be careful not to pinch your fingers. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 4-5 4.2 Users Checksheet (Care and Maintenance) We recommend that you periodically check the following so that you can optimally operate the equipment constantly. Make a copy when you are using this checksheet.  Verification 4 Details Frequency Are the power cable and/or grounding cable connected/fastened properly? Daily Is the cable connected/fastened properly between this equipment and other equipment? Daily Results of users verification Care and Maintenance  Cleaning Unit for cleaning Weekly Pages 6-2 and 6-3 Operation Panel Every three months 6-4 Tray Every three months 6-5 Air filter Every three months 6-6, 6-7 Cleaning roller 4-6 Frequency Reference DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Date of cleaning 4.3 About Preventive Maintenance To maintain safety for the customer, the user, and other people, perform the preventive maintenance mainly involved cleaning of the parts and replacing of consumables. For the preventive maintenance, consult our official dealer or local representative. Necessary cycle of periodical maintenance or part replacement depend on the usage conditions or operation time per day. Details of maintenance or inspections performed by the specified dealers differ depending on the maintenance contract. ■ Preventive maintenance to be performed when the machine has been used for one year Perform the preventive maintenance shown below. Cleaning of the parts • Cleaning roller • Removal unit • Covers • Inside the equipment • Rubber belt • Sub-scanning conveyance roller • Density measurement section 4 Care and Maintenance Checking the Machine • Image/conveyance • Interlock function(Front cover/Right cover /Film tray) • Tray periphery • Error log • Setting date and time • Rubber belt • Improper protective grounding • Final operation Replacing of consumables • Cutter ■ Preventive maintenance to be performed when the machine has been used for two years Perform the preventive maintenance shown below. Replacing of consumables • Air filter ■ Preventive maintenance to be performed when the machine has been used for three years Perform the preventive maintenance shown below. Replacing of consumables • Cleaning roller Cleaning of the parts • Heat development unit DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 4-7 4 Care and Maintenance 4-8 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Appendix A Specifications A.1 Specifications The specifications of the DRYPIX 4000 are shown below. Depending on the intended use, the tray specification can be selected from one-tray, two-tray or threetray type. Standard Components DRYPIX 4000 main unit (One-tray, two-tray and three-tray specification types are available.) Image buffer memory board (1GB) Processing Capacity Max. : Approx. 110 films (14" × 17") / hour. Approx. 160 films (26 × 36cm) / hour. * Note that the processing capacity in actual operation is dependent on the model and usage of a connected modality. Applicable Film Fuji Medical Dry Imaging Film DI-HL (Blue-base) DI-HLc (Clear-base) DI-ML (Blue base) 35.4 × 43.0cm (14" × 17") 100 sheets / pack 35.4 × 35.4cm (14" × 14") 100 sheets / pack 25.7 × 36.4cm (26 × 36cm) 150 sheets / pack 25.2 × 30.3cm (10" × 12") 150 sheets / pack 20.1 × 25.2cm (8" × 10") 150 sheets / pack                Recording Pixel Size 100µm 50µm Specifications Standard High resolution CR Image Size Reduction When you printed a CR Image in real size, printed image size will be almost 100% of reduction rate. * At the printout from the modality, the size of image is automatically scaled according to the print area on the film. Gray Scale 14bits (16384 levels) Maximum Density Select one of 2.64, 3.0 and 3.3. For the DI-ML, select 4.0. * Note that 3.6 and 4.0 are for mammography use only. Power Supply Conditions Input voltage : AC 100-120V/200-240V Allowable variations in voltage : ± 10% Phase : Single Frequency : 50-60Hz Rated current : 12A/6A Environmental Conditions (1) Operating conditions Temperature/humidity : 15ºC (40-70%RH) -30ºC (15-70%RH) (no dew condensation) Maximum heating value : 1800kJ Humidity 70% (2) Non-operating conditions Temperature : 0-45ºC Humidity : 10-90%RH (no dew condensation) 40% 15% 15 C o 30 C o Temperature Supplies Fuji Medical Dry Imaging Film DI-HL (Blue-base), DI-HLc (Clear-base), DI-ML (Blue base) Cutter Options Supply film tray, Sorter DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 A-1 A.2 External View and Weight With no sorters Model Name Width (mm) Depth (mm) Height (mm) Weight (kg) DRYPIX PLUS (DRYPIX 4000) 600 585 1090 160 (including the three trays) • Three-tray: W600×D585×H1090 (mm) m 5m 1090mm 58 60 0m Specifications m • Two-tray: W600×D585×H1090 (mm) A-2 DRYPIX PLUS (DRYPIX 4000) Operation Manual m 5m 56 897N101792 • One-tray: W600×D585×H1090 (mm) With sorters Model Name Width (mm) Depth (mm) Height (mm) Weight (kg) DRYPIX PLUS (DRYPIX 4000) 600 585 1390 170 (including the three trays) • Three-tray: W600 × D585 × H1390 (mm) m 5m 60 0m 1295mm 1390mm 58 m Specifications • Two-tray: W600 × D585 × H1390 (mm) m 5m 56 • One-tray: W600 × D585 × H1390 (mm) DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 A-3 Specifications A-4 DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Maintenance and Inspection 1 Maintenance and Inspection Items Assigned to Specified Dealer For periodical inspection of the equipment and necessary arrangements, consult our official dealer or local representative. Maintenance and Inspection DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 Maintenance and Inspection DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 EULA TERMS FOR MICROSOFT WINDOWS® XP EMBEDDED RUNTIME LICENSES You have acquired a device (“DEVICE”) that includes software licensed by [FUJIFILM Corporation ] from Microsoft Licensing, GP or its affiliates (“MS”). Those installed software products of MS origin, as well as associated media, printed materials, and “online” or electronic documentation (“SOFTWARE”) are protected by international intellectual property laws and treaties. The SOFTWARE is licensed, not sold. All rights reserved. IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT (“EULA”), DO NOT USE THE DEVICE OR COPY THE SOFTWARE. INSTEAD, PROMPTLY CONTACT [FUJIFILM CORPORATION ] FOR INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE(S) FOR A REFUND. ANY USE OF THE SOFTWARE, INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE, WILL CONSTITUTE YOUR AGREEMENT TO THIS EULA (OR RATIFICATION OF ANY PREVIOUS CONSENT). GRANT OF SOFTWARE LICENSE. This EULA grants you the following license: • You may use the SOFTWARE only on the DEVICE. • NOT FAULT TOLERANT. THE SOFTWARE IS NOT FAULT TOLERANT. [FUJIFILM CORPORATION ] HAS INDEPENDENTLY DETERMINED HOW TO USE THE SOFTWARE IN THE DEVICE, AND MS HAS RELIED UPON [FUJIFILM CORPORATION ] TO CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE FOR SUCH USE. • NO WARRANTIES FOR THE SOFTWARE. THE SOFTWARE is provided “AS IS” and with all faults. THE ENTIRE RISK AS TO SATISFACTORY QUALITY, PERFORMANCE, ACCURACY, AND EFFORT (INCLUDING LACK OF NEGLIGENCE) IS WITH YOU. ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST INFRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR THE SOFTWARE, THOSE WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING ON, MS. • No Liability for Certain Damages. EXCEPT AS PROHIBITED BY LAW, MS SHALL HAVE NO LIABILITY FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE SOFTWARE. THIS LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT SHALL MS BE LIABLE FOR ANY AMOUNT IN EXCESS OF U.S. TWO HUNDRED FIFTY DOLLARS (U.S.$250.00). • Limitations on Reverse Engineering, Decompilation, and Disassembly. You may not reverse engineer, decompile, or disassemble the SOFTWARE, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. • SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS. You may permanently transfer rights under this EULA only as part of a permanent sale or transfer of the Device, and only if the recipient agrees to this EULA. If the SOFTWARE is an upgrade, any transfer must also include all prior versions of the SOFTWARE. • EXPORT RESTRICTIONS. You acknowledge that SOFTWARE is of US-origin. You agree to comply with all applicable international and national laws that apply to the SOFTWARE, including the U.S. Export Administration Regulations, as well as end-user, end-use and country destination restrictions issued by U.S. and other governments. For additional information on exporting the SOFTWARE, see http://www.microsoft.com/exporting/. • Limited Use of Particular SOFTWARE Services. Provided that the DEVICE continues to comply with the terms of the “Restricted Functionality” paragraph below, without limiting the number of computers or other electronic devices that might connect to the DEVICE to access or utilize other software or SOFTWARE services on the DEVICE, you may permit a maximum of ten (10) computers or other electronic devices to connect to the DEVICE to utilize the services of the SOFTWARE for (a) file and print services, (b) internet information services, and/or (c) remote access (including connection sharing). The ten (10) connection maximum includes any indirect connections made through multiplexing or other software or hardware which pools or aggregates connections. • If you use the DEVICE to access or utilize the services or functionality of Microsoft Windows Server products (such as Microsoft Windows NT Server 4.0 (all editions) or Microsoft Windows 2000 Server (all editions)), or use the DEVICE to permit workstation or computing devices to access or utilize the services or functionality of Microsoft Windows Server products, you may be required to obtain a Client Access License for the Device and/or each such workstation or computing device. Please refer to the end user license agreement for your Microsoft Windows Server product for additional information. • Restricted Deployment. The SOFTWARE is not designed or intended for use or resale in hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, or other devices or systems in which a malfunction of the SOFTWARE would result in foreseeable risk of injury or death to the operator of the device or system, or to others. • Restricted Functionality. You are licensed to use the SOFTWARE to provide only the limited functionality (specific tasks or processes) for which the DEVICE has been designed and marketed by [FUJIFILM Corporation ]. This license specifically prohibits any other use of the SOFTWARE, or inclusion of additional software programs or functions, on the DEVICE. Subject to the terms of the “Limited Use of Particular Services” paragraph above, you may use the SOFTWARE on the DEVICE to interact with other computers or electronic devices. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792 • Maximum Number of Processors. The SOFTWARE may not be used by more than two (2) processors at any one time on the DEVICE. • Remote Boot Feature. Your DEVICE may be enabled with a Remote Boot feature which includes Remote Boot Installation Services tool. You may use the Remote Boot Installation Services tool only to deploy the SOFTWARE to one or more DEVICEs on which you are licensed to run the SOFTWARE (i.e. DEVICEs to which the appropriate Certificate of Authenticity is affixed). Please refer to the DEVICE documentation, if provided with your DEVICE, or contact [FUJIFILM Corporation ] for additional information. • Security Updates. Content providers are using the digital rights management technology (“Microsoft DRM”) contained in this SOFTWARE to protect the integrity of their content (“Secure Content”) so that their intellectual property, including copyright, in such content is not misappropriated. Owners of such Secure Content (“Secure Content Owners”) may, from time to time, request MS, Microsoft Corporation or their subsidiaries to provide security related updates to the Microsoft DRM components of the SOFTWARE (“Security Updates”) that may affect your ability to copy, display and/or play Secure Content through Microsoft software or third party applications that utilize Microsoft DRM. You therefore agree that, if you elect to download a license from the Internet which enables your use of Secure Content, MS, Microsoft Corporation or their subsidiaries may, in conjunction with such license, also download onto your DEVICE such Security Updates that a Secure Content Owner has requested that MS, Microsoft Corporation or their subsidiaries distribute. MS, Microsoft Corporation or their subsidiaries will not retrieve any personally identifiable information, or any other information, from your DEVICE by downloading such Security Updates. • NetMeeting/Remote Assistance/Remote Desktop Features. The SOFTWARE may contain NetMeeting, Remote Assistance, and Remote Desktop technologies that enable the SOFTWARE or other applications installed on the Device to be used remotely between two or more computing devices, even if the SOFTWARE or application is installed on only one Device. You may use NetMeeting, Remote Assistance, and Remote Desktop with all Microsoft products; provided however, use of these technologies with certain Microsoft products may require an additional license. For both Microsoft products and non-Microsoft products, you should consult the license agreement accompanying the applicable product or contact the applicable licensor to determine whether use of NetMeeting, Remote Assistance, or Remote Desktop is permitted without an additional license. • Consent to Use of Data. You agree that MS, Microsoft Corporation and their affiliates may collect and use technical information gathered in any manner as part of product support services related to the SOFTWARE. MS, Microsoft Corporation and their affiliates may use this information solely to improve their products or to provide customized services or technologies to you. MS, Microsoft Corporation and their affiliates may disclose this information to others, but not in a form that personally identifies you. • Internet Gaming/Update Features. If the SOFTWARE provides, and you choose to utilize, the Internet gaming or update features within the SOFTWARE, it is necessary to use certain computer system, hardware, and software information to implement the features. By using these features, you explicitly authorize MS, Microsoft Corporation and/or their designated agent to use this information solely to improve their products or to provide customized services or technologies to you. MS or Microsoft Corporation may disclose this information to others, but not in a form that personally identifies you. • Internet-Based Services Components. The SOFTWARE may contain components that enable and facilitate the use of certain Internet-based services. You acknowledge and agree that MS, Microsoft Corporation or their affiliates may automatically check the version of the SOFTWARE and/or its components that you are utilizing and may provide upgrades or supplements to the SOFTWARE that may be automatically downloaded to your Device. • Links to Third Party Sites. The SOFTWARE may provide you with the ability to link to third party sites through the use of the SOFTWARE. The third party sites are not under the control of MS, Microsoft Corporation or their affiliates. Neither MS nor Microsoft Corporation nor their affiliates are responsible for (i) the contents of any third party sites, any links contained in third party sites, or any changes or updates to third party sites, or (ii) webcasting or any other form of transmission received from any third party sites. If the SOFTWARE provides links to third party sites, those links are provided to you only as a convenience, and the inclusion of any link does not imply an endorsement of the third party site by MS, Microsoft Corporation or their affiliates. • Additional Software/Services. The SOFTWARE may permit [FUJIFILM Corporation ], MS, Microsoft Corporation or their affiliates to provide or make available to you SOFTWARE updates, supplements, add-on components, or Internet-based services components of the SOFTWARE after the date you obtain your initial copy of the SOFTWARE (“Supplemental Components”). • If [FUJIFILM Corporation ] provides or makes available to you Supplemental Components and no other EULA terms are provided along with the Supplemental Components, then the terms of this EULA shall apply. • If MS, Microsoft Corporation or their affiliates make available Supplemental Components, and no other EULA terms are provided, then the terms of this EULA shall apply, except that the MS, Microsoft Corporation or affiliate entity providing the Supplemental Component(s) shall be the licensor of the Supplemental Component(s). [FUJIFILM Corporation ], MS, Microsoft Corporation and their affiliates reserve the right to discontinue any Internet-based services provided to you or made available to you through the use of the SOFTWARE. Maintenance and Inspection This EULA does not grant you any rights to use the Windows Media Format Software Development Kit (“WMFSDK”) components contained in the SOFTWARE to develop a software application that uses Windows Media technology. If you wish to use the WMFSDK to develop such an application, visit http://msdn.microsoft. com/workshop/imedia/windowsmedia/sdk/wmsdk.asp, accept a separate license for the WMFSDK, download the appropriate WMFSDK, and install it on your system. DRYPIX PLUS (DRYPIX 4000) Operation Manual 897N101792

Drypix Plus (4000) Operation Manual

Rating

Date

Size

Views

Categories

Share

Transcript

Forgot your password?.