Dtenblatt 936067d, K7023210, K702321, K7023211

Transcript

Tram and Bus Antenna 406 ... 470 MHz K702321., K702323. Frequency range 406 – 428 MHz Type No. Input Drill hole dimension Frequency range VSWR Gain Impedance Polarization Max. power Weight Packing size (outside) Height Mounting K7023210 602284 K702321 601514 K7023211 602317 M 11 x 1 female M 11 x 1 female N female (the connector for cable (the connector for cable RG 58 C/U is supplied). RG 213/U is supplied). 12 mm [0.5 inches] 12 mm [0.5 inches] 17 mm [0.7 inches] 406 – 428 MHz 406 – 410 MHz: < 1.9 410 – 425 MHz: < 1.7 425 – 428 MHz: < 1.9 0 dB (ref. to the quarter-wave antenna) 50 Ω Vertical 50 W (at 50 °C ambient temperature) 400 g [0.9 lb] 117 x 117 x 114 mm [4.6 x 4.6 x 4.5 inches] 70 mm [2.8 inches] On a conductive surface 70 x 70 cm [27.6 x 27.6 inches] min. Frequency range 440 – 470 MHz Type No. Input 936.067/d Subject to alteration. Drill hole dimension Frequency range VSWR Gain Impedance Polarization Max. power Weight Packing size (outside) Height Mounting K7023230 602285 K702323 601363 K7023231 602286 M 11 x 1 female M 11 x 1 female N female (the connector for cable (the connector for cable RG 58 C/U is supplied). RG 213/U is supplied). 12 mm [0.5 inches] 12 mm [0.5 inches] 17 mm [0.7 inches] 440 – 470 MHz 440 – 450 MHz: < 1.7 450 – 465 MHz: < 1.5 465 – 470 MHz: < 1.7 0 dB (ref. to the quarter-wave antenna) 50 Ω Vertical 50 W (at 50 °C ambient temperature) 400 g [0.9 ib] 117 x 117 x 114 mm [4.6 x 4.6 x 4.5 inches] 70 mm [2.8 inches] On a conductive surface 50 x 50 cm [19.7 x 19.7 inches] min. Material: Radiator and base: Aluminum. Radome: High impact plastic. All screws and nuts: Stainless steel. Mounting: The drilling diameter is 12 mm except the N connector versions: 17 mm. A special zinc washer ensures a good contact at the edges of the hole. Special features: All metall parts of this antenna are DC grounded. Extreme robust and car-wash proof vehicular antenna. Any previous data sheet issues have now become invalid. K702321., K702323. Page 1 of 1 www.kathrein.com KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820 Steckverbindung M 11 x 1 HF connectors M 11 x 1 K 62 05 1 / BN 510 132 Kabel RG 058-PE D 1. Kabel abisolieren. 2. Kabel am Steckergehäuse befestigen. 3. Innenleiter anlöten. 936.255 Subject to alteration GB 1. Remove the insulation. 2. Fix the cable to the plug casing. 3. Solder the cable core in position. KATHREIN-Werke KG . Telefon (0 80 31) 18 40 . Fax (0 80 31) 18 43 06 Anton-Kathrein-Straße 1 – 3 . Postfach 10 04 44 . D-83004 Rosenheim K 62 10 0 / BN 510 133 Kabel RG 213/U Cable RG 213/U Câble RG 213/U D 1. 2. 3. 4. 1. 2. 3. 4. Remove the insulation. Fix the cable to the plug casing. Solder the inner and the outer conductor in position. Heat the strink sleeve. 936.255 Subject to alteration GB Kabel abisolieren. Kabel am Steckergehäuse befestigen. Innenleiter und Außenleiter anlöten. Schrumpfschlauch anwärmen. KATHREIN-Werke KG . Telefon (0 80 31) 18 40 . Fax (0 80 31) 18 43 06 Anton-Kathrein-Straße 1 – 3 . Postfach 10 04 44 . D-83004 Rosenheim General Information about Panel Antennas Environmental ­conditions: Kathrein cellular antennas are designed to operate under the environmental ­conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regard to the following items: – Low temperature: –55 °C – High temperature (dry): +60 °C For antennas equipped with FlexRET: The electrical downtilt adjusting is designed to operate under the environmental conditions as described in the valid data sheet of the FlexRET. Ice protection: Due to the very sturdy antenna construction and the ­protection of the radiating system by the r­adome, the antenna remains operational even under icy ­conditions. Environmental tests: Kathrein antennas fulfil the stated specifications after completion of the environmental tests as defined in ETS 300 019-2-4. The homogenous d ­ esign of Kathrein’s antenna ­families uses ­identical modules and materials. Extensive tests have been performed on typical samples and modules. The vibration test has been adapted relating to frequency and acceleration to the conditions of mast mounted antennas. Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary ­operating conditions. The mechanical design is based on the environmental conditions as ­stipulated in ETS 300 019-1-4. Wind loads are ­calculated according to ­DIN 1055-4. The antennas may be used at locations where the anticipated peak wind velocity or gust wind speed lies within the maximum wind speed listed in the data sheet. We warrant the mechanical s­afety and electrical functionality under such conditions. ­ The wind speeds are defined in ­accordance with the DIN, EN or TIA standards. This ­warranty makes ­allowance for the partial safety factors specified in those standards. Extraordinary ­operating conditions, such as heavy icing or exceptional d ­ ynamic stress (e.g. strain caused by oscillating support structures), may result in the b ­ reakage of an ­antenna or even cause it to fall to the ground. These facts must be c ­ onsidered during the site planning process. 936.4694/d Subject to alteration. The details given in our data sheets have to be f­ ollowed carefully when i­nstalling the antennas and a ­ ccessories. Site planning and installation must be carried out by qualified and ­experienced staff. All relevant national safety regulations must be upheld and respected. ­Incorrect site planning, faulty installation, as well as i­nterfering surroundings on site, may lead to deviations in the ­electrical parameters compared to those ­specified in the respective data sheets. The connectors on this product are only suitable for connecting to the ­compatible counterpart. Please ensure that the connected cable has been ­ fitted with a ­connector of the same standard, otherwise damage may occur. The tilt values will be set to any arbitrary value in the given tilt range. These values are independent from the frequency band or antenna type and can vary between antennas and bands. EU-RED Hereby, Kathrein Werke KG declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.kathrein.com Our quality assurance system and our environmental management system apply to the entire company and are certified by TÜV according to EN ISO 9001 and EN ISO 14001. RoHS Any previous data sheet issues have now become ­invalid. Our products are compliant to the EU Directive RoHS as well as to other environmentally relevant regulations (e.g. REACH). Page 1 of 1 www.kathrein.com KATHREIN-Werke KG · Anton-Kathrein-Straße 1-3 · P.O. Box 10 04 44 · 83004 ROSENHEIM · GERMANY · Phone +49 8031 184-0 · Fax +49 8031 184-820