Transcript
Car alarm system
DV502 Owner's manual
Control of the security system The turn on / turn off of the alarm is confirmed be the blink of the turn lights and (if programmed) by the beep of the alarm. If the key is in the position “ignition” the alarm can not be turned on. This protects from the accidental turning on the alarm while driving. Silent control of the system is programmed by the producer, i.e. turning on off the system the alarm will not beep. To turn on the audible control apply to the section on the installation manual: Turning on/off the audible control of the security system. Note: the audible control of the security system is allowed only if used outside the EU. Agrees with the UN directive No.97, regarding the requirements for the vehicle security systems. The certificate of the conformance 97RA 01 04816.
Turning on the security system. Press the button 1. The turn lights will blink once, auto lock will turn on and LED will blink as many times as many remote controls are programmed, then will start blink fast (showing input delay time). The alarm will beep if audible control is programmed. When input delay time expires, car alarm will enter into full turn on mode and LED will start blink slowly. If 30 sec. central lock pulse is programmed (it could be used for windows, sunroof lifting control) is possible to interrupt it at any time by pressing remote controller button 1 again (if you would like to leave windows partially opened for example). For higher security when using 30 sec. central lock mode, doors, hood and trunk switches inputs will be activated after 4 sec., but others sensors inputs will be activated after only 30 sec. (to prevent false alarms). Turning off the security system.
1 2
After pressing the button 2 on the remote control the turn light will blink twice. If the audible control is programmed the alarm will beep twice. The auto lock will unlock the car doors and LED will stop blinking.
Audible turning on/off of the security system (if this function is allowed in the programming mode). After pressing any button on the remote control corresponding beep of the alarm will be heard, and silent turn on of the security system will be activated only by pressing button 1 twice. Silent turn off of the security system. This option has sense only if the system is turned on in the audible mode. Press the button 2 twice. The turn light will blink twice (the alarm will not beep), the auto lock will unlock the car doors and LED will stop blinking. Partial turn on of the security system (for example: when children are left in the car). Press the button 1on the remote three times. The turn lights will blink three times (the alarm will beep if audible mode is programmed). LED will start blinking. In this mode the sensors (shock, volume) are disabled and in this way the people inside the car are safe from the harmful emission of the volume sensor. The alarm is caused only by opening the doors, boot or engine capote. Warning about incomplete turning on of the protection. In 4 sec. after tuning on, the security system will go to protection mode. If during those 4 sec. the input of any sensors is triggered (for example the door is not closed or shock sensor is triggered) the security system going to protection mode will warn about this by blinking turn lights and beeps of the alarm three times and will block this input automatically. If the sensor will return to normal protection mode (i.e. the opened door will be closed), then in 3 sec. it will be unblocked and one blink of turn lights will warn about this. Checking if the protection is turned on.
Press button 1 on the remote. If the security system is turned on the turn lights will blink
once.
Turning off the alarm signal. The alarm will be caused if the system is in protection mode and the car doors are opened, the boot/engine capote is opened, the additional sensors are triggered or the ignition is turned on, i.e. the turn lights will blink and the alarm will sound for 28 seconds. To turn off the alarm sound press the button 1 on the remote once (protection mode will remain turned on). The system will not respond to pressing button 2. Control of auto lock while engine is started. If the engine is started (the ignition is turned on), then after pressing the button 1 on the remote – the auto lock will lock the doors, and after pressing button 2 – unlock. Emergency mode / car search. This function is useful for causing short time alarm for chasing away the suspicious persons wandering around the car or looking for the car left in the big parking place. While the system is in protection mode, press both buttons simultaneously. The turn lights will blink for 10 seconds (the alarm will beep 5 times if audible mode is programmed). To stop - press button 1.
Other functions Precise alarm memory.
If turning off the security system the turn lights blink three times (the alarm beeps three times if audible mode is programmed), this means that the system was in alarm mode. After turning on the ignition and pressing button 2 on the remote it is possible to determine what caused the alarm according to the number of LED blinks (see Alarm table).
Alarm table Number of blinks
What caused the alarm
1 2 4 8
T he sensor T he door T he boot or engine capote T urning on the ignition was attempted
Number of alarms. After 5 alarms initiated by the same sensor the sensor are disabled – it will not cause the alarm. It is designed to stop the infinite false alarms. For example if 5 alarms are induced by malfunctioning shock sensor, the alarm will not start if this sensor is triggered, although triggering other sensors or opening the doors will cause the alarm. Control of other installations. With the control channel you can control the electromagnetic car hood lock (if it is connected by installer). This channel is activated by pressing of both buttons at the same time (protection must be turned off).
V.207
1/2
Automatic blocking of engine circuit (if this function is allowed in the programming mode). This function is designed to protect the vehicle when it is forgotten to turn on the security system. The mode can be recognized from the constantly shining LED. The security system will not turn on and will not lock the doors, but it will not be possible to start the engine. To start the engine (to turn off this state) press button 2: diode will fade – blocking will be turned off and you will be able to start the engine. After pressing button 1 the system will go to protection mode immediately. It is possible to choose two modes of automatic blocking: 1. Automatic blocking will turn on in 3 minutes after turning off the ignition. LED will shine constantly. 2. After turning off the ignition and opening the door the blocking will be activated immediately. If the door is not opened (you stay in the car) automatic blocking will turn on in 10 min. LED will shine constantly. Note: this automatic blocking mode can be activated only if the ignition was turned on for 3 or more minutes. Automatic turning on (if this function is allowable in programming mode). This function is designed for automatic turning on the system if you turned off the system and forgot to turn it on again. The security system will turn on automatically if during 1 minute after its turning off the door is no opened, no sensors are triggered or ignition is turned on. It is possible to choose whether the auto lock will lock the doors when this function initiates (see Installation instruction). The number of programmed remote controls. There are two remote controls in the set. The maximum number of remote controls can be used (programmed) is 3. Every time the ignition is turned on, LED will blink as many times as many remote controls are programmed. If one of the remote controls is lost, reprogram the rest near the main block. In this way the code of the lost remote will be deleted from the memory, and nobody will be able to use lost remote. Programming the remote controls. To program the additional (or to change the lost) remote control, perform the following procedure:
When the system is off turn on the ignition (immobilization mode must turned off). Press and hold secret button (for about 5 sec.) until LED will shine constantly and then release it. Press any button on the remote. After programming the first remote all codes of previously programmed remotes will be deleted from the memory and LED will blink once. After pressing the button on the second remote LED will blink twice and on the third – three times. You have about 12 sec. to program all remotes. After 12 sec. or after turning off the ignition the system will go out of remote programming mode automatically.
Emergency turning off of the automatic blocking. If for some reasons the automatic blocking mode can not be turned off using the remote control (LED shines constantly), perform the emergency turn off in exactly the same ways as described in the section: Emergency turning off the security system. Emergency turning off the security system. When the remote control is lost and the security system can not be turned off, perform the emergency turn off. It would be performed in two ways: by pressing secret button or by entering PIN code, according 18 parameter in parameters programming table (see Installation instruction). ✔ If PIN code is not used for emergency turning off, you have to open the door, turn on ignition and press a secret button. ✔ If PIN code is used for emergency turning off, you have enter three digits PIN code by the help of starting lock. Default producer PIN code is 212. (For ex.: digit 2 corresponds turning on ignition twice, digit 5 – turning on 5 times and etc.). For emergency turning off with PIN code you must do: Table of emergency turn off 1) turn on/off the ignition; the system will go to the emergency turning off mode. This will be Number of t urns on/off t he shown by the constantly shining of LED. Watch the state of LED. Short blinks of LED will LED blinks ignit ion show which PIN digit must be entered: when LED fades for the first time, you must turn on/off the ignition as many times as is the first digit of the PIN code. as many times as the 1 st digit of 1 x☼ 2) after 20 second LED will blink twice – you have to enter second digit of PIN code, and after the P IN code 20 seconds more LED will blink three times – enter the last digit of the PIN code. nd 3) if you did everything correctly, LED will fade in 10 sec. and the system will go out of 2 x ☼ as many times as the 2 digit of the P IN code protection mode. 4) if you mixed one of the PIN code sets, wait until the program will go through all the digit rd 3 x ☼ as many times as the 3 digit of entering stages and will go out of this mode. Then try to perform emergency turn off once the P IN code more.
Warranty ➢ Producer of the car security systems Sharpshooter DV502 gives 36-
➢
➢ ➢ ➢ ➢ ➢
month warranty. The warranty period start from the date of purchase. If the purchase documents are not present, warranty time is calculated from the production date, which is shown on the sticker fixed on the system block. Warranty void if the system is remade not according the recommendations of the producer the system is used not according its purpose, if the system is installed improperly, if the signs mechanical, electrical or chemical damage are present, if the device is affected by the humidity and in all other cases, that are not related to the production defects. Producer does not give warranty for the fuses, capote switches, cases of remote controls and batteries. Producer is not responsible for the possible theft of the vehicle. In case of warranty event the buyer must contact the company that installed the security system into the vehicle. Do not forget to check remote control batteries once a year. If the decrease in the remote control working distance is noticed, the batteries must be replaced. Use two batteries of type CR2016 (3V). Regularly check the charge of the car battery (especially in winter). Due to the insufficient charge of the battery the alarm may not turn off.
V.207
Useful to know With the remote controls and a special receiver URC-4 you can control other devices related with the remote signal transmission. I.e. open the garage gate, the yard gate, the electromagnetic lock of the door, to turn on/off the security system of the premises and so on. The receiver URC-4 is made for this purpose. This receiver allows implement these very comfortable functions. Contact the company that installed the system.
Installation certificate By this certificate I confirm that the security system was installed to the vehicle in accordance with all recommendation of the producer.
Vehicle mark: Type: Serial number: State registration number: Vehicle security system Sharpshooter DV502 Installation performed: Date: Assembler address: Assembler name, surname, position: Sign: Stamp:
2/2
