Dvigear: Multiport Tps Extender / Quick Start Guide

Transcript

Quick Start Guide Maximum Cable Lengths Resolution Clock Freq. CAT-5e CAT-5e (1) CAT-6A (2) DVI-TPS-TX90 DVI-TPS-RX90 MultiPort TPS Extender CAT-6A (1)(2) 1024x768 @60Hz 65.00 MHz 328.1 ft. (100 m) 524.9 ft. (160 m) 393.7 ft. (120 m) 590.6 ft. (180 m) Introduction 1280x720p @60Hz 73.84 MHz 328.1 ft. (100 m) 524.9 ft. (160 m) 393.7 ft. (120 m) 590.6 ft. (180 m) 1920x1080i @60Hz 74.25 MHz 328.1 ft. (100 m) 524.9 ft. (160 m) 393.7 ft. (120 m) 590.6 ft. (180 m) DVIGear’s MultiPort TPS Extender supports long-range extension of HDMI (v1.4) signals over a single CAT-X twisted pair (TP) cable at distances of up to 180 meters (590 ft.). These units also support bi-directional RS-232, Infra-Red, 10/100 BaseT Ethernet, and PoE over the same twisted pair link. 1280x1024 @60Hz 108.00 MHz 328.1 ft. (100 m) 524.9 ft. (160 m) 393.7 ft. (120 m) 590.6 ft. (180 m) Typical Application 1920x1080p @60Hz 148.50 MHz 328.1 ft. (100 m) 492.1 ft. (150 m) 393.7 ft. (120 m) 557.7 ft. (170 m) 1920x1200 @60Hz 152.90 MHz 328.1 ft. (100 m) 1600x1200 @60Hz 162.00 MHz 328.1 ft. (100 m) N/A N/A 393.7 ft. (120 m) 393.7 ft. (120 m) IR cable N/A IR Transmitter Serial cable N/A Note 1: With Long Reach firmware installed. This firmware supports pixel clock frequencies up to 148.5 MHz. Please contact DVIGear technical support or your dealer to change or upgrade device firmware. Touch panel Blu-Ray or DVD Player Note 2: CAT6A S/FTP (550 MHz) cable must be used to achieve these distances. HDMI cable Installation WARNING: Ethernet ports are designed to connect to 10/100 Ethernet products. Do not connect Ethernet appliances to TPS IN or TPS OUT ports as it may result in damage to the equipment. 1. 2. 3. 4. 5. 6. Set the switch on the front panel to the Normal position. Connect a CAT-X twisted pair cable to the TPS OUT on the transmitter unit. Connect the other end of the CAT-X twisted pair cable to the TPS IN on the receiver unit. Connect an HDMI signal source to the HDMI IN port on the transmitter unit. Connect an HDMI display device (e.g. projector) to the HDMI OUT on the receiver unit. To use the bi-directional pass-through data lines, connect desired devices to the transmitter and receiver units. See examples in table(3) below. 12V DC Power Adaptor DVI-TPS-TX90 TPS connection CAT-X up to 180m LAN LAN Ethernet switch Internet Serial cable 7. Connect the supplied External AC Power Adapter to either unit. The other unit will automatically receive power over the twisted pair cable connected between the TPS ports. Ethernet Use LAN cables to connect an Ethernet device (e.g. switch) to the Ethernet port on the Transmitter unit and a network device (e.g. projector) to the Ethernet port on the Receiver unit. RS-232 Use serial cables to connect a controller unit (e.g. touch panel) to the RS-232 port on the Transmitter unit, and serial controlled device (e.g. projector) to the RS-232 port on the Receiver unit. Infra-Red Connect the supplied IR Transmitter to the IR OUT port of the transmitter unit. Connect the supplied IR Receiver to the IR IN port on the Receiver unit. Note 3: Examples of optional devices that are supported over the MultiPort TPS twisted pair link. 4 DVI-TPS-TX90_RX90-QSG-01 / August.2012 DVI-TPS-RX90 Remote powered HDMI cable LAN IR cable IR Receiver HD Projector Projection screen MultiPort TPS Extender: DVI-TPS-TX90 and DVI-TPS-RX90 1 Quick Start Guide 8 1 1. Status Indicator LEDs: HDCP VIDEO 7 2 LINK DVI-TPS-TX90 Front View 3 DVI-TPS-TX90 Rear View 5 8 4 1 7 2 Blinking HDCP encrypted video signal transmission — Video signal transmission — 6 2 No HDCP encryption No video signal transmission TPS connection detected and Normal operation TPS connection detected and Power save mode (1) TPS connection failed between TX and RX — Device powered and ready to use No power supply or out of order 2. IR IN/OUT Connect IR Transmitter to IR OUT. Connect IR Receiver to IR IN. 3. HDMI IN/OUT Connect source device to HDMI IN. Connect display to HDMI OUT. 4. TPS IN/OUT Use a high quality TP cable to connect TPS OUT to TPS IN. (2) 5. Ethernet IN/OUT Connect to Ethernet switch and/or devices - see Installation. (2) 6. DC IN Connect AC Power Adapter to either unit, other is powered by TP link. 7. RS-232 IN/OUT Connect to Ethernet switch and/or devices - see Installation. 8. NORMAL / PROG Set to NORMAL position. PROG is only for qualified technical personnel. Note 1: These units enter Power Save mode when no signal is detected on the input. Normal operation is restored when a signal appears on the input. Power Save mode is not supported with Long Reach firmware. Infra-Red Accessories 3 5 Off Note 2: Ethernet ports are designed to connect to 10/100 Ethernet products. Do not connect Ethernet devices to TPS Input or Output as it may result in damage to the equipment. DVI-TPS-RX90 Front View DVI-TPS-RX90 Rear View MultiPort TPS Extender Lit Continuously LIVE 6 DVI-TPS-TX90 DVI-TPS-RX90 IR Units IR Transmitter IR Receiver 4 Connector Locking DC Plug Connect to IR OUT IR IN Twist 90° clockwise to lock DVIGear • 1059 Triad Court, Suite 8, Marietta, GA 30062 • Tel: 770.421.6699 • Toll Free: 888.463.9927 • Fax: 770.234.4207 • [email protected] • www.dvigear.com 3