Transcript
Technical Specifications
© Copyright 2008 Smart-AVI, All Rights Reserved © Copyright 2012 Smart-AVI, All Rights Reserved
DVX PLUS SPECIFICATIONS Video Interface
Single Link Range
Video Data Rate
1.65 Gbps
Resolution
1920 x 1200 @ 60 Hz, Reso lution up to 1280 x 1024 min. 75H
Power Supply
Universal Switch mode PSU (90-240V Input) 5VDC 2A
Input Interface
DVI-D
Notice The information contained in this document is Notice
subject to change without notice. Smart-AVI makes no warranty of anycontained kind with regard this material, The information in thistodocument is including but notwithout limited notice. to, implied warranties subject to change Smart-AVI makes of m erchantof abany ilitykind andwith fitneregard ss for to anthis y pamaterial, rticular no warranty purpose. but not limited to, implied warranties of including Smart-AVI will not be liable for errors contained herein or will for not incidental Smart-AVI be liableor for consequential errors containeddamages herein or in connection the furnishing, performance or for incidental orwith consequential damages in connection use of this material. with the furnishing, performance or use of this material.
USB Data
No part part of of this this document document may may be be photocopied, photocopied, No reproducedoror translated into another language reproduced translated into another language without with prior written consent from Smart-AVI. out prior written consent from Smart-AVI.
USB max data rate
12Mbps
For more information, visit www.smartavi.com. For the complete manual, visit www.smartavi.com.
USB compatibility
1.0 and 1.1
Connector Type
Type A (Transmitter) Type B (Receiver)
QUICK START GUIDE
DVX Plus
The following is the wiring standard for terminating UTP/STP cable using RJ-45 connector: Pair 1 Pair 2 Pair 3 Pair 4 Connectors: Capacitance: Conductor Gauge: Impedance:
Pins 1 & 2 Pins 3 & 6 Pins 4 & 5 Pins 7 & 8 RJ-45 14 pf/ft (46.2 pf/m) 24 AWG 100 +/- 15 ohms
SmartAVI, Inc. / Twitter: smartavi 11651 Vanowen St., North Hollywood, CA 91605 Tel: (818) 503-6200 Fax: (818) 503-6208 http://www.SmartAVI.com
DVI-D and USB extension via Twisted Pair
www.smartavi.com
Introduction
DVX Plus extends Universal Serial Bus (USB 1.1) and Digital Visual Interface (DVI-D) signals via common twisted pair cable. Using a unique method of transparent data transfer, the system allows a USB peripheral and a DVI display to be located up to 275 225 feet from the CPU.
Installation Diagram
Features •
• • • • • • • • • • • •
Extends USB and DVI-D signals up to 275ft 225ft from the computer. Uses easy easytoto install, inexpensive twisted pair install, inexpensive twisted pair cable. cable. Data recovery for digital video. Data recovery for digital video. Supports 1920x1200 digital video resolution. Supports 1920x1200 digital resolution. Fully compliant with USB 1.1video specifications. Fully compliant with USB 1.1 specifications. Supports 1.5 and 12 Mbps data rates. Supports 1.5with and all 12operating Mbps datasystems. rates. Compatible Compatible with adapter all operating systems. and reExternal power for transmitter External power adapter for transmitter and receiver unit. ceiver unit. Fully transparent (does not use any emulation). Fully transparent (does not use any emulation). Plug and play. Plug and play.
Connecting The Transmitter Connecting The Transmitter 1. Connect the transmitter to the host using an A-B 1. Connect the transmitter to the host using an A-B USB USB cable. 2. cable. Connect the transmitter to the host DVI-D using 2. Connect transmitter to the host DVI-D using male male tothe male DVI cable. to male DVI cable. 3. The A side of the USB connector would go to the 3. The A side ofhost the USB the computer and connector the B sidewould wouldgo betoconnected computer host and the B side would be connected to to the transmitter. transmitter. 4. the Check that power LED is lit. The TX/RX LED should 4. Check that power at LED is lit. The TX/RX LED should not not be flashing this time.
5. In the back of the unit connect the CAT5 STP cable that 5. Inwill theconnect back of the unitreceiver connect(DVXU-RX). the CAT5 cable that will to the connect to the receiver (DVXU-RX).
DVX DVX Plus Plus Package Package Contents Content Qty
Items
Part No.
1
DVX Plus Transmitter unit
DVXU-TX
1
DVX Plus Receiver unit
DVXU-RX
2
5 volt dc power supply
PS5VDC2A PS-5D1A-US
A A
B B
Connecting The Receiver Connecting The Receiver 1. Connect the receiver to the peripheral device using 1. Connect receiver to the peripheral device using A-B A-B USBthe cable. In this case the A side of the connecUSB this case the A side thethe connector tor cable. will goInto the receiver unit of and B side ofwill the go to the receiver unit and the B sideUse of the connector connector will go the peripheral. a USB Hub if will go the peripheral. Use a USB Hub if needed. needed. 2.2. Connect the receiver unit to the monitor. Connect the receiver unit to the monitor. 3.3. Join DVX Plus units using shielded cable for DVI-D Jointhe the DVX Plus units using shielded cable for and standard CAT6 STP cable for USB. Once conDVI-D and standard CAT5/6 6 UTP STP cable for USB. nected that the Power LED onPower both receiver Once check connected check that the LED onand both transmitter is on and the RX goesthe OFF, indicating receiver and transmitter is LED on and TX/RX LED is that communication between the twoexists units. beIf flashing, indicatingexists that communication receiver LED is not on, make sure the power supply is tween the two units. If receiver LED is not on, make connected. sure the power supply is connected.
Setting the DDC
Preparing & Connecting System CAT5 Cable DDC provides plug-and-play capability to your Following is the wiring for terminating 5 cable displays. When youstandard plug a display into your CAT computer, using RJ-45 connector: the DDC table in the display tells the computer the to use. This device is capable of Pair 1optimal Pinsresolution 1&2 two Pair 2supporting Pins 3 & 6 primary types of displays: PC and Mac. Pair 3The default Pins 4 & 5 setting is PC. Pair 4
Pins 7 & 8
To change this setting,
Connectors: RJ-45 Capacitance: 14 pf/ft (46.2 pf/m) from the TRANSMITTER Conductor Gauge: 24 AWG by removing the four side100 +/- 15 ohms Impedance: screws. Next, locate the 4 - Pair
DIP switches near the rear of the device next to the Operating Instructions Data Port (RJ45 Ethernet Port). Once installation is completed verify that the power is present at all devices in the system. If computer was on during the set up it might be necessary to reboot the computer. The peripheral devices should be ready for use. switches as shown below:
switches as shown below:
1&2 ON, 3&4 OFF
1&2 OFF, 3&4 ON
