Transcript
SIZE:72*97MM 正面 QUICK START GUIDE
SAFETY PRECAUTIONS
Instruction Manual Automatic Wrist Blood Pressure Monitor PC link function include
Babies, young children or individuals who cannot express their consent are not suitable to take blood pressure measurement.
Avoid smoking, eating or exercising for 30 minutes before taking measurement.
Individuals with serious arteriosclerosis are not suitable to take blood pressure measurement.
1. Sit upright in a chair with your both feet on the floor. 2. Roll up the sleeve to bare your wrist if necessary. Take caution not to constrict the blood flow.
Blood pressure readings may change in case of pregnancy. Pregnant women can consult their doctor before taking measurement.
Ref : INOTP01
Self-measurement is not medical treatment. If there are unusual values, please consult your doctor. Handling batteries properly: - As soon as old batteries run out, replace with new batteries. - Do not use old and new batteries together. - Align the polarities of batteries correctly. - When the unit will not be used for more than 3 months, remove the batteries. Otherwise, batteries may leak and cause damage to the unit.
3. Pull on the end of the cuff until it wraps securely around you wrist. 4. Place your elbow on a table and palm facing upward, so that the cuff will be at the same level as your heart. You can use the storage case to support you arm during the measurement. 5. Press the “POWER” button to turn on the unit. Then press the “START” button. The cuff will automatically inflate and the measurement will start.
2
Start
• • • •
2 User / 120 Total Memory Display date and time Auto-off Power Saving Feature Operated by 2 AAA batteries 4
2. Press the” MEMO “or” PAGE “button to select the current year. 3. Press the”TIME “ button to confirm Year Setting. 4. Follow the same steps to set the Month, Date, Hour and Minute.
2.1 Battery Installation 1. Push and remove the battery cover.
Power
Features
3
PREPARATION
Date/ Time
Page Select (Down)
Memory Recall (Up) Set
6. When the measurement is complete, the cuff will automatically deflate and your systolic and diastolic pressure values and pulse rate will display.
Display
OVERVIEW
5. Place your elbow on a table and palm facing upward, so that the cuff will be at the same level as your heart. You can use the storage case to support your arm during the measurement.
Systolic User 1~ 2 Memory
TAKING MEASUREMENT
Diastolic
Low Battery Indicator Memory No. (1~60 readings)
Note: - Avoid smoking, eating or exercising for 30 minutes before taking measurement. - Do not move or talk during measurement. - Measurement can be taken on either arm.
2. Insert 2 AAA batteries with the polarities in correct direction.
Pulse Pulse Symbol
3. Replace the battery cover. Slide it lightly until the lock securely clicks into place.
Package Contents
Note: Replace batteries when the battery indicator “ shows low voltage.
3.1 Sitting Correctly
”
2.2 Date & Time Setting Note: - Set the correct date and time before taking a measurement. - Date and time should be reset after replacing new batteries.
This unit allows a maximum of 2 users to store measurement records in different User Pages. 1. Press the “POWER” button to turn on the unit. 2. Press”PAGE“button to switch between User Page 1 and 2.
3.3 Taking Measurement 1. Press the “POWER” button to turn on the unit. 2. Press the “START” button. The cuff will automatically inflate and the measurement will start. 3. When the measurement is complete, the cuff will automatically deflate and your systolic and diastolic pressure values and pulse rate will display. 4. Remove the wrist cuff and take note of your measurement results.
1. Press and hold the” TIME“button for a few seconds until the Year display flashes.
2 x AAA Alkaline Batteries
Main Unit
1. Relax 2. Sit upright in a chair with your both feet on the floor. 3. Roll up the sleeve to bare your wrist if necessary. Take caution not to constrict the blood flow. 4. Pull on the end of the cuff until it wraps securely around you wrist. Do not over tighten the cuff. Allow 1-2 cm or ½ inch between the cuff and your hand.
3.2 User Setting
5
6
7
8
MEMORY FUNCTIONS
TROUBLE SHOOTING
SIZE:72*97MM 反面 Note: You can press the “POWER ” button to stop measurement at any time.
After measurement, the last set of measured values will be saved automatically after measurement when the unit is turned off by pressing “ON/OFF” button or by automatic power-off after 3 minutes.
3.4 Heartbeat Readings Besides Systolic and Diastolic values, Pulse will also be displayed after a measurement. Pulse
1. Press the“MEMO“button to enter memory function. 2. If the User Page is not what you want to view, press the ”PAGE“ button to select. 3. Press the”MEMO“button to display the next sets of values. Past readings are displayed from the most recent to the oldest. 4. This can stored up to 60 sets of past readings for each user (2 x 60).
4.2 Delete Past Readings User can delete all the past readings stored in memory by replacing the batteries.
9
10
Model No. Measurement Method Measurement Range Accuracy Inflation Pressure Detection Power Supply Auto Power Off Storage Environment Operation Environment External Dimensions Net Weight Cuff Dimensions Package Content
DW 100 Oscillometric Pressure: 20 – 280 mmHg Pulse Rate: 40 – 195 beats/min Pressure: +/- 3 mmHg Pulse Rate: +/- 5% Pump driven Semi-conductor 2 x AAA batteries 3 minutes after last operation -20°C to 60°C, 10% to 95% RH 10°C to 40°C, 30% to 85% RH 3.35” (L) x 2.36” (W) x 3.15” (H) or 85 x 60 x 80 mm 130 g (batteries excluded) For wrist circumference of 13.5-22 cm Instruction Manual, Battery Set, Storage Case
PC link function include see instruction manual joint
Find our products on www.inocare.fr Manufactured in accordance with International Standards
0123
Importer:
INOVAXION 10 rue Jean Cottin 75018 - Paris - France
Manufacturer：
Truly Instrument Ltd - Hong Kong
Note: Subject to modification without prior notice.
13
Cause
No display when you press the Power/Start button
Have the batteries run out?
Replace new batteries.
Are the battery polarities wrong?
Re-align batteries in correct polarities.
“Err P” displayed
Fail to inflate
Check if the cuff is properly connected.
Do not wash or expose the arm cuff to liquid.
“Err 1” displayed
Deflate too rapidly
Return for servicing.
“Err 2” displayed
Movement during measurement
Do not move during measurement
Remove batteries from the unit when it will not be used for more than 3 months.
Signal interference
Remove interfering source e.g. mobile phones, magnets.
Incorrect results
Measure again.
“Err 3” displayed
EC-Representative：Hong Kong Truly Semiconductor Ltd. 1-2 Alpha Buildings, The Buntings Kestrel Drive, Stowmarket Suffolk, IP14 5GZ, UK
Use a dry, soft cloth to clean the unit, or if desired, use a cloth lightly dampened with water. Do not use alcohol, benzene, thinner or other volatile liquids to clean the unit.
Note: If your problem cannot be solved by the above, consult your store of purchase. Do not disassemble the unit.
11
SPECIFICATIONS
Keep away the unit from direct sunlight, extreme temperatures, humidity or moisture.
Problem
4.1 View Past Readings
Solution
STOTAGE & MAINTENANCE
12
