Dyk50

Transcript

Part Names The symbol and character indicate that unless the following safety regulations are strictly observed, serious personal injury may result. WARNING The symbol and character indicate that unless the following safety regulations are strictly observed, slight personal injury or property may result. CAUTION WARRANTY Product ALARM START/STOP button This button starts and stops time measurements. It can also be used for adjusting numerical values when setting values. ADJUST button This button allows you to put the watch in setting mode. In addition, it is also used for illuminating the backlight. ■How to Set Alarm 1 Keep the ADJUST button pressed for two seconds to blink the hour display. 1 2 Press the START/STOP button to advance the blinking numerical 2秒 values. Adjust the numerical values using this button. 2 LAP/RESET This button is used to adjust numerical values when switching displays or setting values. MODE button This button is used for selecting modes or switching between settings. To Preserve the Quality of Your Watch 3 Press the MODE button to blink the minute display. 4 Press the START/STOP button to advance the blinking numerical values. Repeat the above procedures 2 to 3 , and select the minute, month, day and time zone. Watch Functions 3 ■Mode functions 4 2 years from purchase Warranty Date of purchase : period 5 To set the alarm to go off at the same time everyday, leave the month and day empty. TIME Time and calendars in two time zones are displayed. Name : Address : Custome TEL : Name : Address : MODE switching Press the MODE button to switch the modes. Press the MODE button repeatedly until the mode you want to set is displayed. START/STOP button TEL : (Please read the warranty before use) Terms of Warranty This product will be repaired or replaced free of charge for the period of two years from the date of purchase if it should malfunction during normal use. In this case, please present ① this Warranty and ②your receipt or Internet shopping delivery sheet with this product. his warranty does not apply to any of the following cases. 1) Damage caused by unauthorized use or abuse, 2) Damage caused by unauthorized repair or reconditioning, 3) Damage caused by fire or an Act of God, 4) Esthetic change caused by minor scratches on the case, glass, or watchband during normal use, 5) Battery replacement, 6) Any watchband other than metal watchbands. LAP/RESET button MODE button Frequency of crystal oscillator : 32,768Hz (Hz=Herz-Cycles per second) Loss/gain(monthly rate) : Less than 20 seconds at normal temperature range (5℃ to 35℃)(41℉ to 95℉) (when wearing the watch) Operational temperature range : 0℃ to +40℃ (32℉ to 104℉) CHRNOGRAPH Time can be measured. Displaying the backlight Pressing the ADJUST button causes the backlight to display for three seconds. Fast forwarding numerical digits When setting each mode, pressing the START/STOP button advances blinking numerical values. Deleting all settings and records Simultaneously pressing and holding down the MODE, ADJUST, START/STOP, and LAP/RESET buttons for two seconds will delete all settings and records, restoring the watch to its default settings. Display the alarm number to be turned ON/OFF. （ CHIME is displayed following the alarm. Time tone setting is available. For details, see How to Turn ON/OFF Time Tone .） 1 2 2 Press the START/STOP button to switch between ON and OFF of the alarm. ■How to Stop Alarm When the alarm went off at the specified time, it can be stopped by pressing any button. 1 Press the LAP/RESET button to display the CHIME . 1 second display. 1 2 To set the time tone at every hour, turn it ON. 3 Press the MODE button to blink the hour display. 5 Press the MODE button to blink the minute display. Repeat the above procedures 4 to 5 to adjust the minute, year, month, day, and day of the week. Also, select 12/24 hour display. 4 TIMER ■How to Select Timer Press the LAP/RESET button to switch between the timers. Select a timer that you want to use. 5 6 Press the ADJUST button to save all settings. Two time zones can be set. Keep the LAP/RESET button pressed for two seconds to switch to the other time zone. Repeat the above procedures 1 to 6 . 6 CHRONOGRAPH ●Cr (Countdown Repeat Timer) When the set time elapses, this timer notifies you with the time s up sound and continues the countdown. This timer is suitable for repetitive exercise. ●CS (Countdown Stop Timer) When the set time elapses, this timer notifies you with the time s up sound and stops countdown. ●CU (Countdown Countup Timer) When the set time elapses, this timer notifies you with the time s up sound and start time measurement from that point. This timer is convenient for training with target times. 1 Press the START/STOP button to start time measurement. 1 2 Press the LAP/RESET button to display the split time and the lap time. Then the display switches to the elapsed time display. Press the LAP/RESET button to switch the displays between the split time and the lap time. 2 3 Press the START/STOP button to complete time measurement. 3 ■How to Set Timer 1 Keep the ADJUST button pressed for two seconds to blink the minute display. 1 2秒 2 4 Press the LAP/RESET button to reset the run. ■Water resistance A run WATER RESISTANT WATER RESISTANT 5, 10 BAR Condition of use Degree of water resistance Splashes and rain in daily living. Water-resistance Water-resistance 5 BAR Water-resistance 10 BAR ○ ○ ○ Swimming, kitchen work, etc. Skin diving without scuba. ○ ○ Genuine diving using scuba or helium gas. ○ WARNING ・ After using a 10-bar or 5-bar water-resistant watch in a bathing place, remove salt, etc. as soon as possible. If not, the watch may rust. If you rinse the watch under running water, excessive water pressure applies to the watch and causes a failure in its water resistance. Always rinse the watch in a pot or bowl and be careful not to apply excessive water pressure to the watch. ・ If a leather band gets wet, its durability may be affected. ■Places to keep your watch ・ When not in use, the watch may be damaged, deteriorated or broken in any of the following cases: ①if the watch is exposed to a temperature below -5℃ or above +50℃ for a long time, its performance may be impaired or it may stop operating. ②if the watch is exposed to direct sunlight, high temperature or low temperature for a long time, it may gain or lose in timekeeping. ③if the watch is exposed to magnetic leakage from TV sets, speakers, mobile phones, magnetic necklaces, etc., it may gain or lose in timekeeping. ④if the watch is exposed to strong vibration, it may be broken or gain or lose in timekeeping. ⑤if the watch is exposed to chemicals or chemical steam, it may be deteriorated or broken.  Examples of chemicals: Benzine, thinner, manicure, cosmetics spray solvents, cleaners, toilet solvents, adhesive agents, mercury, iodized disinfectants, insect repellents, etc. ⑥if the watch is exposed to hot spring water or other special environment or put in a box containing insect-killer, it may be deteriorated. ⑦it is recommended that the watch be put in a clean box or case and stored in a well-ventilated place. ■Periodic check ・ We suggest that you have your watch checked every 2 or 3 years by the retailer from whom you purchased the watch. Depending on how the watch is used, the lubrication of the watch mechanism may become insufficient, parts may become worn due to impurities in the lubricating oil, or the watch may be running noticeably fast or late. Seals, etc. may also become worn and the water-resistance of the watch may degrade. Take your watch to the retailer from whom you purchased it for inspection and adjustment through disassembly/cleaning. ・ When replacing the parts such as battery, please specify GENUINE PARTS . ・ It is recommended that the gasket and the push-pin be also replaced with new ones. ■Operation instruction for buttons ・ Press the button firmly by applying the force evenly. values. Adjust the numerical values using this button. Press the MODE button to blink the second display. Repeat the above procedure 2 to adjust the second. Remarks on the Battery 4 ■Monitor battery Battery : Lithium battery (CR1632) ■How to Start/Stop Timer 1 Lap time 2 1 Press the START/STOP button to start the timer. When the timer countdown is finished, the time s up sound goes off. 2 Press the START/STOP button to stop the timer. Split time Start CAUTION ・ Adjust the bracelet or band so that there will be a little clearance between the bracelet or band and your wrist to avoid accumulation of perspiration. ・ If you are constitutionally predisposed to rash or depending on your physical condition, the band may cause you to develop a rash or disorder. ・ The possible causes of the rash are as follows:  ①Allergy to metals or leathers  ②Rust, dust or perspiration on the watch or band ・ If you develop any skin reactions, take off the watch and consult a doctor immediately. 4 Press the ADJUST button to save the timer setting. 3 Alarm function : Alarm setting time (hour and minute); PM (in the 12-hour indication); number of setting=2ch (AL-1,2); ON/OFF switch 2 Press the START/STOP button to advance the blinking numerical 3 4 Integrated circuit : C-MOS-IC=1 piece ■Rash and allergy CAUTION values. Adjust the numerical values using this button. Battery life : Approximately 2 years(calculated based on the use of 3 seconds lighting, 1 alarm ; 20 seconds, 15 minutes timer and 30 minutes stopwatch operation per day) CAUTION ・ The case and bracelet touch your skin directly just as underwear. If they are left dirty, the edge of a sleeve may be stained with rust or those who have a delicate skin may have a rash. ・ After removing the watch from your wrist, wipe perspiration or moisture with a soft cloth. This will prevent the watch from being soiled, allowing for prolongation of the life of the gasket. ・ Your watch is extremely sensitive to chemicals, including benzine, thinner, alcohol, detergent and other organic solvents. Keep your watch away from chemicals and avoid their chemical reaction to your watch. If not, it may be deteriorated. 〈Leather band〉  When removing moisture from a leather band, do not rub the band with a cloth as this may discolor it or reduce its gloss. Be sure to blot up the moisture using a soft dry cloth. 〈Metal band〉  Clean the watch band with a soft toothbrush dipped in water or soapy water and be sure to blot up the moisture using a soft dry cloth. If your watch is not water-resistant, be careful not to get the case wet when cleaning. 〈Soft plastic band〉  If your watch has a soft plastic band such as urethane band, do not leave the watch under a fluorescent lamp or direct sunlight for a long time, or do not leave the band soiled. Otherwise, the band may be discolored, hardened or broken. If your watch has a semitransparent, white or light-colored urethane band, which is easily discolored, special care should be taken to keep it clean. Depending on the condition of use, the semitransparent band may be discolored after several months of use.  Do not keep the watch in a place where it is exposed to high humidity, or do not leave the band wet with perspiration or water. Otherwise, the band may be discolored in a very short time.  When the band is soiled, rinse it in soapy water. Do not use solvents for cleaning as some solvents may deteriorate the band. ・ NEVER WEAR 10-bar water-resistant watch during saturated diving and air diving. ・ NEVER WEAR 5-bar water-resistant watch during any type of diving including skin diving. ・ NEVER PUT 3-bar water-resistant watch into water. 4 Press the START/STOP button to advance blinking numerical Timer function : Countdown repeat timer (maximum setting=99 minutes and 59 seconds); Countdown stop timer (maximum setting=99 minutes and 59 seconds); Countdown countup timer (maximum setting=99 minutes and 59 seconds) ■Care of your watch 2 Press the START/STOP button to switch between ON and OFF. 2 2 Press the START/STOP button to reset the second display. 2秒 3 CAUTION ・ When clasping and unclasping the band, you may damage your nail, depending on the type of a clasp used with the band.  Check the dial or case back of your watch for the water resistant quality, and then see the table below. 1 Keep the ADJUST button pressed for two seconds to blink the Stopwatch function : Minimum measuring unit=1/100 second; measuring range=0 to 99 hours, 59 minutes and 59.99 seconds; measuring function=lap time, split time ※The specifications are subject to change without prior notice, for product improvement. ■How to Turn ON/OFF Alarm ■How to Turn ON/OFF Time Tone ■How to Set Time Basic functions : Displaying year, month, day, day of the week, PM (in the 12-hour indication), hour, minute and second; dual time display (T1/T2); 12/24 hours display switching function; fully automatic calendar (2009-2089) Other functions : Backlighting Press the ADJUST button to save the alarm setting and turn ON the alarm. Two alarms can be set. To set the other alarm continually, repeat the above procedures 1 to 6 . 1 Press the LAP/RESET button to switch the alarm numbers. TIME （Manufacturer） Specifications 6 Press the MODE button to blink the month display. WARNING ・ In case you tumble, fall or bump into others with the watch worn on your wrist, you may be injured by the reason of the fact that you wear the watch. ・ When you make contact with children, especially with infants, they may get injured or develop a rash caused by allergy. ・ Your watch may damage property or malfunction depending on your actions when wearing it. Special care should be taken. Indication of water resistance (on the back of your watch case) The case, dial, hands, glass, bracelet, or any part of them may be replaced with substitutes if the originals are not available. ■This Warranty guarantees that you can receive free repair or replacement in accordance with the terms set forth herein and within the specified period, and shall not restrict any lawful rights of the Customer. 5 6 TIMER Three timers (three channels) can be set. ■Other functions ADJUST button Store ALARM Two alarms can be set. ■Precautions on wearing your watch ・ Since the battery in your watch is a monitor battery inserted at the factory to check the functions and performance of the watch, it may run down in less than the specified period after the date of purchase. ■Battery replacement ・ For battery replacement, be sure to have the battery replaced with a genuine battery at the retailer or the dealer from whom you purchased the watch. ・ If the old battery is left in the watch for a long time, a malfunction may be caused due to battery leakage, etc. Have it replaced with a new one as soon as possible. ・ Battery replacement is charged even if it runs down within the guarantee period. WARNING Goal ●Run A run is time measurement from the start to the goal, consisting of several laps. ●Lap Lap time is the time required to run through the specified zone within a run. ●Split Split time is the total amount of time from the start to the end of each lap. ■How to Reset Timer  Press the ADJUST button to reset countdown of Cr (Countdown Repeat Timer) and CU (Countdown Countup Timer). ・ The battery is not rechargeable. Never attempt to recharge it, as this may cause battery leakage or damage to the battery. ・ Do not remove the battery from the watch. ・ If it is necessary to take out the battery, keep it out of the reach of children. ・ If a child swallows it, consult a doctor immediately as it will affect the health of the child. CAUTION ・ Do not leave your watch out of the room temperature from 5℃ to 35℃ for a long time. Doing so may shorten the battery life or cause a malfunction due to battery leakage.