Dynamic Controller

Transcript

Dynamic Controller Owner’s Manual MODEL : LKD1000 Before installing and using the product, please read this owner's manual carefully and retain for future reference. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. REGULATORY INFORMATION: FCC Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. • A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.  • Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. • Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings. Warning: Do not install this equipment in a confined space such as a bookcase or similar unit. Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70. Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture. Caution: This installation should be made by a qualified service person and should conform to all local codes. Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus. This product is manufactured to comply with the EEC DIRECTIVE 2004/108/EC and 2006/95/EC. Disposal of your old appliance 1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. IMPORTANT SAFETY INSTRUCTIONS CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE. This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing. This product does not contain any parts that can be repaired by the user. DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY. 1. Read these instructions. - All these safety and operating instructions should be read before the product is operated. 2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference. 3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the product. 11. Only use attachments/accessories specified by the manufacturer. 4. Follow all instructions. - All operating and use instructions should be followed. 5. Do not use this product near water. – For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement; or near a swimming pool; and other areas located near water. 6. Clean only with dry cloth. – Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over- heating. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with apparatus. When a cart is used, use caution when moving the cart/product combination to avoid injury from tip-over. 13. Unplug this product during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the product, the product has been exposed to rain or moisture, does not operate normally, or has been dropped. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.  CONTENTS OPERATION....................................... 12 Operation the LG DVR.......................................12 INTRODUCTION................................... 5 About LKD1000 Controller..................................5 Features................................................................5 Identification of the Controller ..........................6 Operation the connected camera via the DVR................................................................14 Operation of the camera connected to the LKD1000 controller directly..................14 Camera Setup Menu..........................................15 Camera setup menu overview.......................15 HOOKUP AND SETTINGS................... 8 Basic Connection Overview...............................8 RS-485 Connection..............................................9 Preset Settings...............................................15 Auto Pan Setup and Activation......................20 Pattern Setup and Activation.........................21 Privacy Setup.................................................22 Connecting the LG DVR......................................9 Communication Settings................................23 Connecting the PTZ Camera..............................9 Camera Settings............................................25 Connecting the multiple LKD1000 controller...9 System Operation..............................................10 LKD1000 SETUP MENU.....................................10 Camera Control Function.................................27 Key Functions on the Set Up.........................10 Pan/Tilt Control..............................................27 Change Password..........................................11 Lens Control...................................................27 About DVR.....................................................11 Specifications....................................................28 About Camera................................................11 Change ID Setting..........................................11 Auto Lock Setting . ........................................12 Factory Default...............................................12 About LKD1000..............................................12  REFERENCE ..................................... 27 INTRODUCTION About LKD1000 Controller This controller is the brand of Dome Camera and DVR Control Keyboard of LG in a surveillance system. You can operate this system very easily and conveniently because of design structure based on biotechnology and various functions for users. In addition, the controller can control using the functions of the LG Dome Camera and LG DVR system. Features The Dynamic Controller offers the following functions: x User-friendly Graphic User Interface. x Compatible with LG Dome Cameras, Zoom Cameras and LG DVRs. x Joystick Control of PTZ Functions. x Program Preset Position up to 128 and Pattern Control (Memorize continuous series of Zoom In/Out, Pan/Tilt). x Control Privacy Zone Masking of the camera. x Easy Firmware Upgrade (Please contact authorized service center or where you purchased to upgrade the firmware.) x Ergonomic Design. x Directly Control the camera connected to LG DVR by using BY-PASS function of LKD1000 controller. x Connect maximum 16 controller by using cascade (Master 1, Slave 15) x Support multithread operation to implement controller's cascade and preset touring of camera which originally has no touring function. Note: The Dynamic Controller is not provided with functions to control the audio signal. Audio communication is not possible, regardless of whether audio boards are installed in the receiver.  Identification of the Controller  a h b c i j d e f g k l m n o p 1 LG DVR Control Buttons For details, see page 13. 2 Display Window Displays function menus, numeric input, and system status. 3 Numeric (0-9) and Arrow (left/right/up/down) Buttons Selects an option in the menu. These buttons are used for numeric input of preset numbers or for executing each parameter on the Controller’s menu. 4 Set Up Button Opens controller’s main Set Up menu in the display window. 5 OSD Button Opens or closes the Camera’s Setup menu on the screen. 6 In/Out Buttons These buttons are used to zoom the camera image In (TELE) and Out (WIDE). 7 Joystick Controller This joystick manually operates the Pan/Tilt Head and turning the joystick head to the right or left will zoom or widen the image. (The zooming level will go up or down.) qa Open/Close Buttons The lens Iris is adjusted by pressing the OPEN or CLOSE button. qs Near/Far Buttons These buttons are used to adjust the lens focus of cameras equipped with the specified lens. qd RS-485 Data Ports (CH 2) This port is used to connect the other LKD 1000 controller. If you want to use the multiple LKD1000 controller, connect the RS-485 1CH of the other LKD1000 controller to this port using the RS-485 cable. qf RS-485 Data Ports (CH 1) This port is used to exchange control data through the connected camera and/or DVR via the RS-485 cable or by connecting the master (or the other) controller. qg RS-232C Port Is used only for authorized service purposes. qh DC 12V Input Jack (12V DC) Connect a DC 12V Certified/Listed, class 2 power supply only to the DC input terminal on the back of the controller. 8 PTZ Camera Control Buttons • PRESET Button For details, see pages 15-19. • A-PAN (Auto-Pan) Button For details, see pages 20-21. • PTRN (Pattern) Button For details, see pages 21-22. • ALARM Button For details, see pages 19-20. • FUNC Button This button is for additional function that may be added. 9 CLR (CLEAR) Button This button is used to return to the previous menu or mode. Clears the parameter entered by numeric buttons. 0 ENTER Button This button is used to execute the currently highlighted setting in the Setup menu.  HOOKUP AND SETTINGS Precautions • The connections should be made by qualified service personnel or system installers in accordance with all local codes. • DC 12V can be used. Basic Connection Overview LKD1000 Controller 1 (MASTER) DC 12V adaptor (Not supplied). To RS-485 2CH terminal. To RS-485 1CH terminal. RJ11 Cable (Supplied) LKD1000 Controller 2 (SLAVER) DVR 1 DVR 2 DVR 3 Up to 16 DVRs. LKD1000 Controller 3 (SLAVER) LKD1000 Controller 4 (SLAVER) Camera 1 Camera 2 Up to 16 controllers. Up to 256 cameras. Note: Please refer to the LG DVR and Camera manuals as necessary for additional connection information.  RS-485 Connection Connecting the PTZ Camera Use this port to connect PTZ cameras or LG DVRs. Use the cable that is described below for RS-485 site communication. • Shielded, twisted pair cable • Low impedance • Wire gauge size is thicker than AWG #22 (0.33 mm2). You can connect up to 256 PTZ cameras. 6 RX5 RX+ 1-4 GND Connecting the PTZ Camera to the RS-485 1CH terminal of the LKD1000 as shown below. 6 TX5 TX+ 1-4 GND Connecting the LG DVR You can connect up to 16 LG DVRs. Connecting the LG DVR to the RS-485 1CH terminal of the LKD1000 as shown below. Connecting the multiple LKD1000 controller You can connect up to 16 LKD1000 controllers. If you use the multiple LKD1000 controller, you must set the LKD1000 ID. Set to 1 for master controller and set to the other ID number (2~16) for the slave controller. The Slave LKD1000 controller can control the DVRs or cameras through the master LKD1000 controller. When connecting multiple LKD1000 controllers, connect as shown below. Master LKD1000 Controller First Slaver LKD1000 Controller To RS485 2CH To RS485 1CH To RS485 1CH Notes: • When connecting lines, connect the TX - of the LKD1000 controller to RX - of the LG DVR and TX + of the LKD1000 controller to RX + of the LG DVR correctly. • Set the appropriate DVR system ID to operate via the LKD1000 Controller when using the multiple LG DVR. To LG DVRs or Cameras. To RS485 2CH To RS485 1CH To RS485 2CH Second Slaver LKD1000 Controller  System Operation LKD1000 SETUP MENU Before starting operation, user authentication by the password is required. 1. Check that the LG DVR or the camera, the monitor and peripherals are connected correctly and securely. 2. Connect an DC 12V power source to the DC 12V input terminal on the back of the controller. The display for entering your password appears in the controller’s display window. PASSWORD: _ NUM 3. Enter your password using the number buttons then press ENTER. (Initial password is “000000”.) The main menu will appear in the display window. The Setup menu has several submenus. All of these main menus are further divided into submenus. Press Set Up to display the setup menu. Key Functions on the Set Up • Set Up button: To display the main menu. • ENTER button: To execute or select modes and parameters. To enter a submenu for the selected item. • CLR button: To return to the previous menu or to delete input. • Numeric buttons: Enter numbered value in a menu. • Arrow buttons/Joystick Controller: Moves an item in the menu. Joystick Controller DVR Set Up button ENTER button Number and Arrow buttons CLR button 10 Go to Up [CAM] Change Password About Camera The factory default of password is “000000”. However, for security, you should change the password setting. Select [About Camera] option then press ENTER. Shows camera information. Change Password LKD1000 1. Select [Change Password] option then press ENTER. The sub menu will appear. Change Password About Camera LKD1000 About DVR 2. Enter current password using the number buttons then press ENTER. About ChangeDVR Password Go to Upper Menu CURRENT: _ NEW : [DVR] 1 2 3 4 CONFIRM: Select C cam LKD1000 5 6 7 8 Notes:dvr 1 2 3 4 5 6 7 8 • You can enter the password from minimum 1-digit [ENTER] : Add DVR number to 20-digit numbers. [CLR] : Del DVR • We recommend that you do not operate the conChange LKD1000 troller duringID saving the password. Are you sure to Add DVR About DVR Select [About DVR] option then press ENTER. Shows DVR information. 1 9 LKD1000 Connectable Max Camera#: 256 Factory Default LKD1000 Are you s LKD1000 LKD1000 [ENTER] : Add DVR [CLR] : Del DVR 3. Enter new password using the number buttons then press ENTER. Enter the password again About Camera LKD1000 to confirm, and press ENTER. The password is stored. Select DVR No DVR1 About DVR 9 LKD1000 Auto Lock 1 Go to Upper Menu About Camera LKD1000 [DVR] 1 2 3 4 5 Change ID Setting 6 7 8 9 10 11 12 13 14 15 16 This LKD1000 controller has the controllerLKD1000 ID. If you About LKD1000 use 2 controller or more simultaneously, set the controller ID for each controller. Select DVR-Camera No Device Change ID LKD1000 dvr 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1. Select [Change ID] option then press ENTER. The sub menu will appear. Change ID LKD1000 Are you sure to Add DVR/Camera Current LKD1000 ID: 1 LKD1000 ID: _ LKD1000 2. Enter the New LKD1000 ID for this controller (1~16). 3. Press ENTER to save the settings. Connectable Max DVR#: 16 11 Factory Default About DVR Auto Lock Setting LKD1000 The keys on the controller is locked when there is no operation for selected duration on the [Auto Lock] option. To release the Key Lock mode, you need to enter the password. LKD1000 About LKD1000 Select [About LKD1000] option then press ENTER. Shows model name and the current firmware version of the controller. About LKD1000 LKD1000 Auto Lock LKD1000LKD1000 About Camera Change IDNONE After 1 min After 3 min After 5 min LKD1000 OPERATION • NONE: Auto Key Lock function is disable. • After 1 min: The keys on the controller is locked when there is no operation for 1 minutes. • After 3 min: The keys on the controller is locked when there is no operation for 3 minutes. • After 5 min: The keys on the controller is locked when there no operation for 5 minutes. AutoisLock LKD1000 Operation the LG DVR You can control the connected LG DVR using the LKD1000 controller. 1. Select DVR icon in the main menu and then press ENTER. The DVR ID input menu will be displayed. DVR Factory Default DVR If you need to, you can reset the LKD1000 controller to its original factory settings. Factory Default LKD1000 1. Select [Factory Default] option then press ENTER. The confirm message will appear. About LKD1000 LKD1000 [Factory Default] Are you sure? Please Enter DVR ID Target DVR ID : _ Please Enter DVR ID Target DVR ID : _ 2. Enter the connected DVR ID to control the DVR and then press ENTER. The DVR key emulation DVR EMULATION /DVR1 menu willKEY be displayed. DVR KEY EMULATION /DVR1 DVR INPU DVR INPU 2. Press ENTER to reset the controller. /DVR1/CAM 12 /DVR1/CAM M 3. Press ENTER to change the DVR control mode. DVR KEY EMULATION /DVR1 INPUT KEY : • LOG Displays or removes the System Log List. • MARK Sets the mark point for recording search. • COPY 4. Select the communication speed between DVR and controller using the Open / Close buttons. 5. Use the DVR function keys to control the DVR. Copies the recording data to an external device. • REC Starts or stops instant recording. How to instant recording (1) Press the REC and then press the channel button you want to record. PRESET /DVR1/CAM1 • LOCK Displays the lock menu to change the user type or disable the system operation. • SETUP PRESET 000 PTZ Displays the setup menu or cancels operation on the setup menus. Use to return to the previous menu or mode. • SEARCH Displays the search menu. • MAIN Display the MAIN menu to set the screen mode to full, 4, 6, 8, 9 or 16 screens. • SPOT Enter SPOT mode to allow spot monitor control. (2) Press ENTER to start recording. The recording type indicator turns green on the selected channel screen. (3) If you stop the recording, repeat the step (1)~(2) as the above. • Playback control buttons - X: Pauses playback. - m: Search the recorded images in reverse or skip the recorded images. - bB: Playback or reverse playback of recorded images. - M: Forward search the recorded images or skip the recorded images. - x: Stops playback. 6. Press CLR to exit the DVR control mode. • NUM Switches to number entering mode in a menu. • ALM.OFF Cancels alarm activation and returns the system to the condition before the alarm was activated. • OSD Accesses or removes the System Control Bar. • INFO Displays or removes system information. 13 Please Enter DVR ID Target DVR ID : _ Operation the connected camera via the DVR. VR You can control the connected camera via the LG DVR the KEY EMULATION /DVR1 DVR using LKD1000 controller. 1. Follow steps 1-2 described in “Operation the LG DVR”. 2. Use the Arrow ( / ) buttons or joystick to select the camera and then press ENTER. The DVR/ CAM ID input menu will be displayed. Bb Operation of the camera connected to the LKD1000 controllerDVR directly. KEY EMULATION /DVR1 You can control the camera connected to the INPUT KEY : LKD1000 controller directly. 1. Select CAM (Camera) icon in the main menu and then press ENTER. The camera ID input menu will be displayed. CAM CAM /DVR1/CAM DVR KEY EMULATION /DVR1 DVR1 INPUT KEY : PRESET /DVR1/CAM1 Please Enter Camera ID Please Enter Camera ID Target CAM ID : _ Target CAM ID : _ Please Enter DVR/CAM ID Target DVR/CAM ID : _ VR1/CAM 3. Enter the connected DVR/CAM ID to control the camera connected to the DVR and then press ENTER. The camera control menu will be displayed. PRESET /DVR1/CAM1 Bb 4. Use the Arrow ( / ) buttons to select the "COMMUNICATION" option and press ENTER. COMMUNICATION /DVR1/CAM1 5. Set the PROTOCOL desired options. (For more details, see /DVR1/CAM1 pages 23-25) Protocol (No Protocol) 6. Use Baudrate the camera control buttons and joystick to (9600) control the camera. Parity Bit (NONE) 14 BAUDRATE Protocol (No Protocol) Baudrate (9600) Parity Bit (NONE) /DVR1/CAM1 2. Enter the connected camera ID to control the camera connected to the LKD1000 controller directly and then press ENTER. The camera control menu will be displayed. PRESET /CAM1 PRESET /CAM1 Bb 3. Use the Arrow ( / ) buttons to select the "COMMUNICATION" option and press ENTER. 4. Set the desired options. (For more details, see pages 23-25) 5. Use the camera control buttons and joystick to control the camera. DATA BIT /DVR1/CAM1 Data Bit (8bit) Stop Bit (1bit fixed) Speed (127,127,3) STOP BIT Data Bit (8bit) Stop Bit (1bit fixed) Speed (127,127,3) /DVR1/CAM1 Please Enter DVR ID Target DVR ID : _ Camera Setup Menu DVR KEY EMULATION /DVR1 The Camera Setup menu has several submenus: System Setup, Preset Data Load, and Communication. All of these main menus are divided into submenus. Camera setup menu overview Main Menu Sub Menu /DVR1/CAMPage Set Preset 15 Go to Preset 16 Tour 16 Edit Group 17 PRESET Group Tour 18 Clear Preset 18 Clear All Preset 19 Please Enter DVR/CAM ID Set Alarm Input 19 Target DVR/CAM ID : _ Set Alarm Output 20 Set Auto Panning 20 AUTO PANNING Run Auto Panning 21 Record Pattern 21 PATTERN Play Pattern 22 Set Zone Area 22 PRIVACY ZONE Display Zone Area 23 Protocol 23 Baudrate 24 Parity Bit 24 COMMUNICATION Data Bit 24 Stop Bit 24 Speed 24 Sync Communication 25 Manual Focus Speed 25 PTZ Home Position 25 CAMERA SETTING PTZ Position Reset 26 Remote PTZ Reset 26 Factory Default 26 Note: The pictures used in the camera setup menu are based on DVR-camera menu. Preset Settings DVR KEY EMULATION /DVR1 Preset position is the function to register camera INPUT KEY : (preset positions) associated monitoring positions with position numbers. By entering the position numbers, you can move cameras to the preset positions. Note: To activate this function, you need to register the preset positions of combination camera. To register preset positions 1. Select the [PRESET] icon and press ENTER. The sub menu will appear. PRESET /DVR1/CAM1 2. Select [Set Preset] option then press ENTER. The sub menu will appear. SET PRESET /DVR1/CAM1 EDIT G Set Preset Go to Preset Tour SET PRESET Edit Grou Group Tou Clear Pres /DVR1/CAM1 SELEC Number (0~127) : _ Speed (0~127) : Park Time(1~255) : [SELECT 3. By moving the joystick, move the camera to a point you want. 4. Enter aGO [Number] number (0-127) you wnat to TO PRESET /DVR1/CAM1 register by pressing the numeric buttons then SetENTER. Preset press Goa to Preset (0-127) to move to the preset 5. Enter [Speed] Tour Then press ENTER. position. 6. Enter a [Park Time] (holding time) (1-255). Then press ENTER. The position and its number are memorized for GO TO PRESET /DVR1/CAM1 later recall. [Go steps To] 7. Repeat 3-6 to add additional position. Preset : return to the previous menu. 8. Press CLR#to (0~127) EDIT G Presets : Add Pre Del Pre Grou 15 TOUR Set Preset Go to Preset /DVR1/CAM1 select gr DVR KEY EMULATION /DVR1 /DVR1 INPUT KEY : /DVR1/CAM Changing to Picture at Preset Position The following function is available only with cameras provided with the preset function. The preset function makes the combination camera SET PRESET preset /DVR1/CAM1 move to the programmed position. It is necessary to program preset positions for the Set Preset combination Go to camera Preset beforehand. TourPlease Enter DVR/CAM ID 1. Select Target the [PRESET] DVR/CAMicon ID :and _ press ENTER. The sub menu will appear. VR1/CAM PRESET SET PRESET /DVR1/CAM1 /DVR1/CAM1 Number (0~127) : _ Speed (0~127) : Park Time(1~255) : 2. Select [Go to Preset] option then press ENTER. The sub menu will appear. GO TO PRESET /DVR1/CAM1 Set Preset Go to Preset Tour INPUT : SETKEY PRESET /DVR1/CAM1 Go to Preset Number (0~127) : _ Tour Speed (0~127) : SET PRESET /DVR1/CAM1 Park Time(1~255) : Number (0~127) : _ SET (0~127) PRESET : /DVR1/CAM1 Speed Park Time(1~255) Number (0~127) :: _ GO preset TO PRESET /DVR1/CAM1 (0~127) : To tourSpeed the positions Park Time(1~255) : Preset You canSet tour all preset positions. Go to Preset GO TO PRESET /DVR1/CAM1 1. Select Tourthe [PRESET] icon and press ENTER. TheSet sub menu will appear. EDIT GROUP /DVR1/CAM1 Preset TO PRESET /DVR1/CAM1 GoGO toGroup Preset Edit PRESET /DVR1/CAM1 Tour SetGO Preset Group Tour TO PRESET /DVR1/CAM1 Go toPreset Preset Clear [Go To] Tour Preset # : GO TO PRESET /DVR1/CAM1 (0~127) 2. Select [Tour] option then press ENTER. [GoSELECT To] GROUP /DVR1/CAM1 ThePreset sub will appear. /DVR1/CAM1 GOmenu #TO : PRESET [SELECT GR] : 1 2 3 4 (0~127) [Go To]TOUR /DVR1/CAM1 Preset # : 5 6 7 8 Set Preset (0~127) Go to Preset TOUR /DVR1/CAM1 Tour Set Preset EDIT GROUP /DVR1/CAM1 /DVR1/CAM1 Go to TOUR Preset Tour Presets : Set Preset TOUR /DVR1/CAM1 Addto Preset Go Preset # : Del Preset # : Tour [Preset Tour] Are you sure? TOUR GO TO PRESET /DVR1/CAM1 [Go To] Preset # : (0~127) 3. Use number buttons to enter the memorized preset position’s index number then press ENTER. TOUR /DVR1/CAM1 The camera moves to the preset position and the picture of the camera in that position appears on Set Preset the Go monitor. to Preset Tour TOUR /DVR1/CAM1 [Preset Tour] Are you sure? [Preset Tour] /DVR1/CAM1 AreTOUR you sure? 3. Press ENTER. [Preset Tour] All registered preset positions in the camera will /DVR1/CAM1 AreTOUR you sure? be selected, and the camera position image will be displayed on the active monitor. Group /DVR1/CAM1 [Preset Tour]#1 Are you sure? select TOUR gr : 1 touring.. 2/DVR1/CAM1 3 4 ok to preset [Preset Tour] 5 6 7 8 /DVR1/CAM1 AreTOUR you sure? TOUR /DVR1/CAM1 to preset touring.. [PresetokTour] [Preset Tour] Are you sure? 4. You canAre stop thesure? tour by pressing CLR button or CLEAR /DVR1/CAM1 okyou toGROUP preset touring.. TOUR /DVR1/CAM1 moving the joystick. stop touring [Clear [PresetGroup] Tour] /DVR1/CAM1 Are you AreTOUR you sure? sure? stop touring [Preset Tour] Are you sure? stop touring SELECT GROUP 16 /DVR1/CAM1 [Preset Tour] Are you sure? ok to preset touring.. TOUR [Preset Tour] Are you sure? /DVR1/CAM1 /DVR1/CAM1 Edit Group Group Tour Clear Preset Group Tour [Group Tour] [ [ P P s s [ /DVR1/CAM1 5. Press CLR to exit preset tour mode. TOUR G C /DVR1/CAM1 [ E G C E G C E G C[ [ [ M DVR KEY EMULATION /DVR1 INPUT KEY : SETgroup PRESET To edit the /DVR1/CAM1 Preseta group using preset positions that You canSet create Go to Preset are registered already. A maximum of 8 group is Tour available. 1. Select the [PRESET] icon and press ENTER. EDIT GROUP The sub menu will appear./DVR1/CAM1 SET PRESET /DVR1/CAM1 Edit Group PRESET /DVR1/CAM1 Group NumberTour (0~127) : _ Clear SpeedPreset (0~127) : Park Time(1~255) : 2. SelectSELECT [Edit Group] option then press ENTER. GROUP /DVR1/CAM1 The sub menu will appear. [SELECT GR]PRESET : GO TO 1 2 /DVR1/CAM1 3 4 /DVR1/CAM1 SetEDIT PresetGROUP 5 6 7 8 Go to Preset Edit Group Tour Tour Group Clear Preset EDIT GROUP /DVR1/CAM1 GO TO PRESET /DVR1/CAM1 Presets : Add #: [Go To]Preset GROUP SELECT /DVR1/CAM1 Del Preset #: Preset #: [SELECT 1 2 3 4 (0~127) GR] : EDIT GROUP /DVR1/CAM1 5 6 7 8 Edit Group Group Tour TOUR /DVR1/CAM1 to select group 3. UseClear Arrow ( / /v/V) buttons Preset number (1~8) then press ENTER. Set Preset EDIT GROUP /DVR1/CAM1 Go to Preset Group #1 /DVR1/CAM1 Tour Presets : SELECT GROUP /DVR1/CAM1 Add Preset # : select gr : 1 2 3 4 Del Preset # : [SELECT GR] : 1 2 3 4 5 6 7 8 TOUR 5 6/DVR1/CAM1 7 8 4. Use[Preset the joystick to select [Add Preset #] or [Del Tour] Preset #] option. Are you sure? CLEAR GROUP /DVR1/CAM1 Bb EDIT GROUP /DVR1/CAM1 [Clear Group] Are you sure? Presets : Group #1 /DVR1/CAM1 Add Preset # : TOUR select gr : # : 1 2/DVR1/CAM1 3 4 Del Preset [Preset Tour] 5 6 7 8 Are you sure? ok to preset touring.. SELECT GROUP /DVR1/CAM1 TOURGROUP EditCLEAR Group Group [Clear Group] [PresetTour Tour] ClearAre Preset Group #1 you sure? stop touring select gr : 1 Group Tour 5 /DVR1/CAM1 /DVR1/CAM1 /DVR1/CAM1 2 6 3 4 7 8 /DVR1/CAM1 C GROUP /DVR1/CAM1 5. Enter EDIT the preset number that is already registered andEdit press ENTER. Group TheGroup presetTour number is added to the group or deleted from the group. Clear Preset Ed Gro Cle Note: CLEARnumber PRESET /DVR1/CAM1 The added preset is displayed up to 4 preset numbers. You can add the preset number Edit Group SELECT GROUP /DVR1/CAM1 up to 255. Group Tour [SELECT GR] : to additional 6. Repeat steps 4-5 preset Clear Preset 1 2 3 4 number. C [Cl Pre (0~ Note: 5 6 7 8 The available groups and indexes differ depending on cameras. So please refer to camera’s CLEAR PRESET /DVR1/CAM1 manual. 7. Press EDIT CLR[Clear toGROUP exitPreset] edit group mode. /DVR1/CAM1 Preset Num : CLEAR PRESET /DVR1/CAM1 Presets (0~127) : Add Preset #: Edit Group To clear group Dela Preset : Group #Tour You can delete a memorized group. Clear Preset CLE Cle Set Set 1. Follow steps 1-2 described in “To edit the group”. CLEAR ALL PRESET /DVR1/CAM1 2. Select group number (1~8) you want to delete Clear All using the arrow ( Preset / /v/V) buttons then press CLEAR PRESET /DVR1/CAM1 Alarm Input CLR. The Set clear group menu is displayed. Set Alarm Output [Clear Preset] CLEAR /DVR1/CAM1 Preset NumPRESET : Group #1 /DVR1/CAM1 (0~127) Edit Group select CLEAR gr : Tour 1 PRESET 2 3 /DVR1/CAM1 4 Group ALL Bb CLE [Cle Clear Preset5 6 7 8 [Clear All Preset] Are you sure? CLEAR ALL PRESET /DVR1/CAM1 SET Cle Set Set Clear All Preset CLEAR PRESET /DVR1/CAM1 CLEAR GROUP /DVR1/CAM1 Set Alarm Input [Clear Preset] Set Alarm Output [Clear Group] Preset Num : AreSET youALARM sure? INPUT /DVR1/CAM1 (0~127) SET Clear All Preset CLEAR Set AlarmALL InputPRESET /DVR1/CAM1 4. Press ENTER. Set Alarm Output The group[Clear will be Alldeleted. Preset] CLEAR ALL PRESET /DVR1/CAM1 Are you sure? Clear All Preset /DVR1/CAM1 SELECT GROUP SET ALARM INPUT /DVR1/CAM1 Set Alarm Input Edit Group Set Alarm Output Alarm Input : OFF ( 4 : ON 6 : OFF ) Group Tour Alarm Index : Clear Preset SET ALARM INPUT /DVR1/CAM1 Duration Time : Clear All ALL PresetPRESET /DVR1/CAM1 CLEAR Set Alarm Input [Clear All Preset] Set Alarm Output /DVR1/CAM1 Group Tour Are you sure? [GroupSET Tour]ALARM OUTPUT /DVR1/CAM1 Group Num : Clear All Preset (1~8)SET ALARM INPUT /DVR1/CAM1 Set Alarm Input Alarm InputOutput : OFF ( 4 : ON 6 : OFF ) Set Alarm SET /DVR1/CAM1 AlarmALARM Index :INPUT Ala Ala Dur SET Cle Set Set 17 SET Ala Ala INPUT KEY : INPUT KEY : 1/CAM1 CLEAR ALL PRESET /DVR1/CAM1 [Clear All Preset] Are you sure? Group #1 VR1/CAM gr : To tourselect the group 1/CAM1 /DVR1/CAM1 /DVR1/CAM 1 2 3 4 5 is 6 7 8already. You can tour the group that registered 1. Select the [PRESET] icon and press ENTER. The sub menu will appear. CLEAR GROUP /DVR1/CAM1 PRESET /DVR1/CAM1 [Clear Group] Please Enter DVR/CAM ID Are you sure? Target DVR/CAM ID : _ 1/CAM1 To clear the preset position You can delete a memorized preset position. SET ALARM INPUT /DVR1/CAM1 1. Select the [PRESET] icon and press ENTER. Clearwill All appear. Preset The sub menu Set Alarm Input Set Alarm Output /DVR1/CAM1 PRESET SET ALARM INPUT 2. Select [Group Tour] option then press ENTER. The sub menu will appear. 1 EDIT SELECT GROUP GROUP /DVR1/CAM1 /DVR1/CAM1 1/CAM1 SELECT GROUP Group Tour /DVR1/CAM1 /DVR1/CAM1 [SELECT GR] :Tour]1 [Group 2 Group Num : 5 6 (1~8) 3 4 7 8 3. Use number buttons to enter the group number that is already then press ENTER. EDIT GROUPregistered /DVR1/CAM1 The camera moves to the preset position in the Presets group: and the picture of the camera in that posiAdd Preset # :on the monitor. tion appears Del Preset # : M1 2. Select [Clear Preset] Alarm Inputoption : OFF then ( 4 : press ON 6ENTER. : OFF ) The sub menu appear. Alarmwill Index : Duration Time : CLEAR PRESET /DVR1/CAM1 Edit Group Group Tour Clear SET PresetALARM OUTPUT /DVR1/CAM1 Edit Group Edit Group Group Group Tour Tour Clear Preset Clear Preset 1 1/CAM1 /DVR1/CAM1 M1 Clear All Preset Set Alarm Input Set Alarm Output CLEAR PRESET /DVR1/CAM1 [Clear Preset] Preset Num : (0~127) SET ALARM OUTPUT /DVR1/CAM1 Alarm Output : OFF ( 4 : ON 6 : OFF ) 3. Use number buttons to enter the memorized preAlarm Index : set index number then press ENTER. Duration Time : The preset position will be deleted. CLEAR ALL PRESET /DVR1/CAM1 Clear All Preset Set Alarm Input Set Alarm Output CLEAR ALL PRESET /DVR1/CAM1 [Clear All Preset] Are you sure? Group #1 select gr : 1 /DVR1/CAM1 1 2 3 4 5 6 7 8 SET ALARM INPUT CLEAR GROUP /DVR1/CAM1 /DVR1/CAM1 Clear All Preset Set Alarm Input Set Alarm Output [Clear Group] Are you sure? 1 18 SET ALARM INPUT /DVR1/CAM1 Alarm Input : OFF ( 4 : ON Alarm Index : Duration Time : 6 : OFF ) INPUT KEY : Set Alarm Output CLEAR ALL PRESET /DVR1/CAM1 [Clear All Preset] Are you sure? M M Group /DVR1/CAM1 To clear all #1 preset position CLEAR PRESET /DVR1/CAM1 select : Group 2 3 preset 4 position. You cangr delete all 1memorized Edit Group Tour5 1. Select the [PRESET]6icon7and 8 press ENTER. Clear Preset The sub menu will appear. PRESET /DVR1/CAM1 CLEAR GROUP /DVR1/CAM1 CLEAR PRESET /DVR1/CAM1 2. Select [Set Alarm Input] option then press ENTER. The sub menu will appear. SET ALARM INPUT /DVR1/CAM1 Clear All Preset Set Alarm Input Set Alarm Output [Clear Group] [Clear Preset] Are Preset you sure? Num : (0~127) 2. Select [Clear All Preset] option then press ENTER. The sub menu will appear. CLEAR ALL PRESET /DVR1/CAM1 SELECT GROUP /DVR1/CAM1 Clear All Preset Edit Group Set Alarm Input Group Tour Set Alarm Output Clear Preset CLEAR ALL PRESET /DVR1/CAM1 Group Tour /DVR1/CAM1 [Clear All Preset] [Group Tour] Are you sure? Group Num : (1~8) DVR KEY toEMULATION /DVR1 3. Press ENTER delete all preset positions. INPUT KEY : SET ALARM INPUT /DVR1/CAM1 All Input Preset To set Clear Alarm Set Alarm Input You can set alarm input mode, alarm index, and Set Alarm Output duration time. Preset numbers 1 to 8 are linked to alarm inputs 1 to 8 respectively. If alarm input 1 comes in, the camera turns to preset position 1, and to otherSET positions according input 2 to 8. ALARM INPUT to alarm /DVR1/CAM1 (This operating description is based on the LG product.) Alarm Input : OFF ( 4 : ON 6 : OFF ) Alarm Index : 1. Select the [PRESET] Duration Time : icon and press ENTER. The sub menu will appear. PRESET /DVR1/CAM1 SET ALARM INPUT /DVR1/CAM1 Alarm Input : OFF ( 4 : ON Alarm Index : Duration Time : 6 : OFF ) 3. Use 4 (ON) or 6 (OFF) number buttons to select Alarm Input Mode then press ENTER. • ON: Alarm input signals are supplied from SET ALARM OUTPUT /DVR1/CAM1 external devices through the ALARM IN connector on Preset the camera to turn the camera to a Clear All preset position. Set Alarm Input Set Alarm Output ignores alarm inputs. • OFF: The camera 4. Enter a [Alarm Index] number (1-8) then press ENTER. Note: SET ALARM OUTPUT /DVR1/CAM1 The available alarm index differs depending on Alarm So Output : OFF ( 4 to : ON 6 : OFFmanual. ) cameras. please refer camera’s Alarm Index : 5. Enter a [Duration Time] (0-255) then press Duration Time : ENTER. Displays the picture at the preset position for the selected duration. (0 (Manual mode); the camera hold at the preset position continuously. To escape Manual mode, set the [Alarm Input] to OFF.) Alarm input setting is finished and the setting is memorized in the camera’s memory. 6. Repeat the steps 3-6 to set additional Alarm Input. SET ALARM OUTPUT /DVR1/CAM1 Clear All Preset Set Alarm Input Set Alarm Output 19 SET ALARM OUTPUT /DVR1/CAM1 Alarm Output : OFF ( 4 : ON Alarm Index : 6 : OFF ) CLEAR ALL PRESET /DVR1/CAM1 Clear All Preset Set Alarm Input Set Alarm Output To set Alarm Output You can set alarm output mode, alarm index, and duration time. When alarm inputs/DVR1/CAM1 are supplied via CLEAR ALL PRESET DVR KEY EMULATION /DVR1 the alarm input connector on the camera, the cam[Clear All Preset] era sends output signals via the alarm output conINPUT KEY : Arecamera. you sure? nector on the Alarm output numbers 1 to 4 are linked to alarm inputs 1 to 4 respectively. If alarm input 1 comes in, the camera sends output signals via the alarm output 1 connector on the camera. (This operating description is based on the LG prod/DVR1/CAM1 uct.) SET ALARM INPUT Note: Clear All Preset Set Alarm Input You cannot use this function with a camera without Set Alarm Output alarm output connector. /DVR1 1 VR1/CAM M1 1. Select the [PRESET] icon and press ENTER. The sub menu will appear. SET ALARM INPUT /DVR1/CAM1 PRESET /DVR1/CAM1 Alarm Input : OFF ( 4 : ON Alarm Index : Duration Time : 6 : OFF ) M1 2. Select [Set Alarm Output] option then press ENTER. The sub menu will appear. SET ALARM OUTPUT /DVR1/CAM1 Clear All Preset Set Alarm Input Set Alarm Output 1 SET ALARM OUTPUT /DVR1/CAM1 Alarm Output : OFF ( 4 : ON Alarm Index : Duration Time : 6 : OFF ) 3. Use 4 (ON) or 6 (OFF) number buttons to select Alarm Output Mode then press ENTER. • ON: If alarm input comes in, the camera sends output signals. • OFF: The camera does not send an output signal. 4. Enter a [Alarm Index] number (1-4) then press ENTER. 20 5. Enter a [Duration Time] (0-255) then press ENTER. Sends the output signals for the selected duration. (0 (Manual mode); the camera sends output signals continuously.) Alarm output setting is finished and the setting is memorized to the camera’s memory. 6. Repeat steps 3-5 to set additional Alarm Output. Auto Pan Setup and Activation You will set up and activate the auto pan function. The camera can pan among the points you will set. Note: Refer to the operating instructions of camera for details on the auto pan function. To set the points of auto pan 1. Select the [AUTO_PANNING] icon and press ENTER. The sub menu will appear. AUTO_PANNING AUTO_PANNING /DVR1/CAM1 /DVR1/CAM1 2. Select [Set Auto Panning] option then press ENTER. SETmenu AUTO /DVR1/CAM1 The sub will PANNING appear. Set Auto Panning SET AUTO PANNING /DVR1/CAM1 Run Auto Panning Set Auto Panning Run Auto Panning SET AUTO PANNING /DVR1/CAM1 Auto-Pan No.# : _ SET AUTO PANNING /DVR1/CAM1 Speed (0~127) : Auto-Pan No.# : :_ Park Time(1~255) Speed (0~127) : Park Time(1~255) : 3. By moving the joystick, move the camera to a point you want. 4. Enter a [Auto-Pan No.#] number then press ENTER. 5. Enter a [Speed] (0-127) to move to the preset position. Then press ENTER. 6. Enter a [Park Time] (holding time) at the preset position (1-255). The setting is finished and the setting is memorized in the camera’s memory. 7. Repeat the steps 3-6 to add additional position. To activate auto pan 1. Select the [AUTO_PANNING] icon and press ENTER. The sub menu will appear. AUTO_PANNING /DVR1/CAM1 2. Select [Run Auto Panning] option then press ENTER. SET AUTO PANNING /DVR1/CAM1 The sub menu will appear. Set Auto Panning AUTO PANNING /DVR1/CAM1 RUN Run Auto Panning Set Auto Panning RUN AUTO PANNING /DVR1/CAM1 Run Auto Panning Set Auto Panning Run Auto Panning SET AUTO PANNING /DVR1/CAM1 Auto-Pan No.# : _ AUTO /DVR1/CAM1 RUN Speed (0~127)PANNING : Park Time(1~255) : [Run Auto Panning] RUN AUTO PANNING /DVR1/CAM1 Are you sure? [Run[stop] Auto Panning] Are you sure? [stop] 3. Press ENTER to activate auto pan. RUN AUTO PANNING /DVR1/CAM1 [Run Auto Panning] RUN AUTO PANNING /DVR1/CAM1 Are you sure? [Run[running] Auto Panning] Are you sure? [running] Pattern Setup and Activation You will perform the pattern setup and the pattern play. Note: The available patterns differ depending on camera. So please refer to camera’s manual. To record the pattern 1. Select the [PATTERN] icon and press ENTER. The sub menu will appear. PATTERN /DVR1/CAM1 PATTERN /DVR1/CAM1 PATTERN 2. Select [Record Pattern] option/DVR1/CAM1 then press ENTER. The RECORD sub menu will appear. /DVR1/CAM1 PATTERN PLAY RECORD PATTERN /DVR1/CAM1 Record Pattern Play Pattern Record Pattern Play Pattern RECORD PATTERN /DVR1/CAM1 PLAY Record Pa Play Patte Record Pa Play Patte PLAY RecordRUN Pattern AUTO PANNING /DVR1/CAM1 RECORD Play PatternPATTERN /DVR1/CAM1 Auto Panning /DVR1/CAM1 RECORD PATTERN RecordSetPattern Run Auto Pattern No : _ Panning Record Pattern (1~4) Pattern No : _ RECORD PATTERN /DVR1/CAM1 (1~4) Record Pa PlayPLAY Patte PLAY [Play Patt Pattern No [Play Patt (1~4) Pattern No (1~4)PLAY Record Pattern RUN AUTO PANNING /DVR1/CAM1 RECORD /DVR1/CAM1 Pattern :PATTERN _ 3. Use numberNo buttons to select the pattern index [Run press Auto Panning] (1~4) number then ENTER /DVR1/CAM1 to confirm. RECORD PATTERN Record Pattern Are you sure? Pattern recording Pattern No : 1 starts. Record Pattern [stop] Pattern Recording . . Pattern No : 1 RECORD PATTERN /DVR1/CAM1 Pattern Recording .. [Play Patt PLAY Pattern No (1~4) PLAY [Play Patt Pattern No [Play Patt Pattern Pl Pattern No PLAY Pattern Pl RUN AUTO PANNING /DVR1/CAM1 Record Pattern Pattern No : 1 Panning] [Run Auto Pattern Recording .. Are you sure? [Play Patt Pattern No Pattern Pl [running] 21 RECORD PATTERN /DVR1/CAM1 Record Pattern Pattern No : _ 4. Perform (1~4)desired camera operations by moving the joystick or pressing In/Out buttons. The following controls are available for recording the pattern. RECORD PATTERNcontrol /DVR1/CAM1 • Panning/Tilting/Zoom (joystick) Record Pattern • Zoom control (In/Out buttons) Note:Pattern No : 1 Pattern Recording . . Press CLR button if you cancel the recording during recording a pattern. 5. If you finish to record, press ENTER. The pattern is memorized in the camera’s memory. 6. Repeat the steps 2-5 to add additional position. PLAY PATTERN /DVR1/CAM1 [Play Pattern] Pattern No : _ 4. Use (1~4) number buttons to enter the memorized pattern index number then press ENTER. The camera plays the pattern. PLAY PATTERN /DVR1/CAM1 [Play Pattern] Pattern No : 1 Pattern Playing . . 5. Press CLR button or move the joystick to stop playing. Privacy Setup Note: The available total time of pattern differs depending on camera’s operation. When the time is over, the pattern setup will automatically stop. This setting is used for masking unwanted zones, hiding them from display on the monitor screen. Up to 8 zones can be registered. Submenus are provided for zone number selection and parameter setting. To register a new privacy zone Pattern Play You can activate the pattern play function for the selected camera. 1. Select the [PATTERN] icon and press ENTER. The sub menu will appear. PATTERN 1. Select the [PRIVACY ZONE] icon and press ENTER. The sub menu will appear. PRIVACY ZONE PRIVACY ZONE /DVR1/CAM1 /DVR1/CAM1 /DVR1/CAM1 R1/CAM1 2. Select [Play Pattern] option then press ENTER. The sub menu will appear. RECORD PATTERN /DVR1/CAM1 PLAY PATTERN /DVR1/CAM1 Record Pattern Play Pattern Record Pattern Play Pattern 1/CAM1 RECORD PATTERN /DVR1/CAM1 PLAY PATTERN /DVR1/CAM1 Record Pattern 1/CAM1 1/CAM1 PatternPattern] No : _ [Play (1~4) No : _ Pattern (1~4) 22 RECORD PATTERN /DVR1/CAM1 PLAY PATTERN /DVR1/CAM1 Record Pattern PatternPattern] No : 1 [Play Recording .. Pattern No :1 Pattern Playing . . 2. Select [Set Zone Area] option then press ENTER. The sub menu will appear. SET ZONE AREA /DVR1/CAM1 SET ZONE Set Zone AreaAREA /DVR1/CAM1 Display Area Set ZoneZone Area PLAY PATTERN Display Zone Area Record Pattern Play Pattern /DVR1/CAM1 SET ZONE AREA /DVR1/CAM1 SET ZONE Zone] AREA /DVR1/CAM1 [Set Privacy Zone No : _ [Set Privacy Zone] PLAY PATTERN /DVR1/CAM1 (1~8) Zone No : _ [Play (1~8) Pattern] Pattern No : _ (1~4) PLAY PATTERN [Play Pattern] Pattern No : 1 Pattern Playing . . /DVR1/CAM1 DIS DISP Set Dis Set Dis DIS DISP Dis Zon Dis (1~ Zon (1~ 3. Adjust the pan, tilt, and zoom position so that the desired position comes into the zone frame with the joystick. 4. Use number buttons to select the zone index number then press ENTER to confirm. The grey zone frame appears on the center of monitor. 5. Repeat the steps 2-4 to add additional position. To display or disappear privacy zone 1. Select the [PRIVACY ZONE] icon and press ENTER. The sub menu will appear. PRIVACY ZONE 4. Enter a [Zone No] number (1-8). The display zone setting has been completed and the setting is memorized in the camera’s memory. 5. Repeat steps 3-4 to set additional zone. Communication Settings This setting is required to establish a connection between the system units and system controller. Select the [COMMUNICATION] icon and press ENTER. COMMUNICATION /DVR1/CAM1 /DVR1/CAM1 M1 2. Select [Display Zone Area] option then press ENTER. ZONEwill AREA /DVR1/CAM1 The SET sub menu appear. Set Zone Area DISPLAY ZONE AREA /DVR1/CAM1 Display Zone Area Set Zone Area Display Zone Area SET ZONE AREA /DVR1/CAM1 [Set Privacy Zone] DISPLAY ZONE AREA /DVR1/CAM1 Zone No : _ Display : OFF (4:ON 6:OFF) (1~8) Zone No : (1~8) NUM 3. Use 4 (ON) or 6 (OFF) number buttons to select Display Mode then press ENTER. • ON: The veiling function does not work. • OFF: Preset privacy zones are veiled on the monitor screen. PROTOCOL /DVR1/CAM1 COMMUNICATION /DVR1/CAM1 Protocol (No Protocol) Protocol Setting Baudrate (9600) Bit (NONE) This itemParity lets you set a protocol for RS-485 commuDISPLAY ZONE AREA /DVR1/CAM1 nication. Set Zone Area option then press ENTER. 1. Select [Protocol] Display Zone Area The subBAUDRATE menu will appear. /DVR1/CAM1 PROTOCOL /DVR1/CAM1 Protocol (No Protocol) DATA Data Bit ( Stop Bit ( Speed (12 STO Data DATA Bit ( Baudrate (9600) Protocol (No Protocol) Parity Bit (9600) (NONE) Baudrate Parity ZONE Bit (NONE) DISPLAY AREA /DVR1/CAM1 Stop Data Bit ( SpeedBit(12( Stop Speed (12 DisplayPARITY : OFF (4:ON BIT 6:OFF) /DVR1/CAM1 Zone No : BAUDRATE /DVR1/CAM1 Protocol (No Protocol) 2. Select the desired parameter from NUM [LG Multix], (1~8) Baudrate (9600) Protocol (No Protocol) [LG old], [Pelco P], [Pelco D] and [LG Zoom Parity Bit (9600) (NONE) Baudrate Cameras]. Parity Bit (NONE) 3. Press ENTER to save the settings. PARITY BIT MOV STO Data Bit ( Stop Bit ( Data Speed Stop Bit(12( Speed (12 SYN MOV Sync Com Data Bit ( Stop Bit ( Speed (12 /DVR1/CAM1 Protocol (No Protocol) Baudrate (9600) Parity Bit (NONE) SYN Sync Com 23 COMMUNICATION /DVR1/CAM1 COMMUNICATION Baud Rate (Communication/DVR1/CAM1 Speed) Setting PROTOCOL /DVR1/CAM1 Data Bits DATA Setting BIT The speed of communication Protocol (No Protocol) between the system controller and the camera. Baudrate (9600) This item lets set the number of the data bits for Data Bityou (8bit) RS-485Stop communication. Bit (1bit fixed) 1. Select [Parity Bit] option then press ENTER. Speed (127,127,3) The sub menu will appear. 1. Select [Baudrate] option then press ENTER. Parity Bit (NONE) The sub menu will appear. PROTOCOL BAUDRATE /DVR1/CAM1 /DVR1/CAM1 Protocol (No (No Protocol) Protocol) Protocol Baudrate (9600) (9600) Baudrate Parity Bit Bit (NONE) (NONE) Parity 2. SelectCOMMUNICATION the desired parameter/DVR1/CAM1 from 9,600 / 1,200 / BAUDRATE /DVR1/CAM1 BIT / 38,400 /DVR1/CAM1 /DVR1/CAM1 2,400 COMMUNICATION /PARITY 4,800 / 19,200 / 57,600 / 115,200 bps.Protocol Protocol (No (No Protocol) Protocol) Note: Baudrate (9600) (9600) Baudrate Conform to the baud rate of other Paritythis Bit parameter (NONE) Parity Bit (NONE) system units. Otherwise, communication will not be established between the system controller PROTOCOL /DVR1/CAM1 PARITY and system units.BIT COMMUNICATION /DVR1/CAM1 PROTOCOL /DVR1/CAM1 Protocol (No Protocol) 3. PressProtocol ENTER(No to save the settings. Protocol) Baudrate (9600) Protocol (No Protocol) Baudrate Parity Bit (9600) (NONE) Baudrate (9600) Parity Bit (NONE) Parity Bit (NONE) Parity bit Setting BAUDRATE /DVR1/CAM1 The parity bit, added to the data, to perform parity PROTOCOL /DVR1/CAM1 BAUDRATE /DVR1/CAM1 check. Protocol (No Protocol) Baudrate (9600) Protocol (No Protocol) 1. Select [Parity(No Bit]Protocol) option then press ENTER. Protocol Parity Bit (NONE) Baudrate (9600) The sub menu(9600) will appear. Baudrate Parity Bit Bit (NONE) (NONE) Parity PARITY BIT /DVR1/CAM1 BAUDRATE /DVR1/CAM1 PARITY BIT /DVR1/CAM1 Protocol (No Protocol) Protocol (No (No Protocol) Baudrate (9600) Protocol Protocol) Baudrate (9600) Parity Bit (9600) (NONE) Baudrate Parity Bit Bit (NONE) (NONE) Parity 2. Select the desired parameter from [NONE], [ODD Parity], and [EVEN Parity]. 3. Press ENTER to save PARITY BIT the settings. /DVR1/CAM1 Protocol (No Protocol) Baudrate (9600) Parity Bit (NONE) DATA BIT BIT STOP /DVR1/CAM1 /DVR1/CAM1 /DVR1/CAM1 Data Bit Bit (8bit) (8bit) Data Stop Bit Bit (1bit (1bit fixed) fixed) Stop Speed (127,127,3) Speed (127,127,3) 2. Select the desired parameter from [8 Data Bits] STOP BIT /DVR1/CAM1 MOVE SPEED /DVR1/CAM1 and [9 Data Bits]. Data Bit Bit (8bit) (8bit) Note: Data Stop Bit (1bit (1bit fixed) fixed) ThisStop setting must be compatible with the periphBit Speed (127,127,3) erals connected. Speed (127,127,3) 3. Press ENTER to save the settings. DATA BIT /DVR1/CAM1 MOVE SPEED /DVR1/CAM1 /DVR1/CAM1 DATA /DVR1/CAM1 Data SYNC Bit (8bit)BIT DataSetting Bit (1bit (8bit) Stop Stop Bit Sync Communication Data Bit Bit (8bit)fixed) Stop Bit (1bit fixed) Speed (127,127,3) Stop (1bit to fixed) The stop bit,Bit added the last of data, in Speed (127,127,3) Speed (127,127,3) asynchronous communication. The parameter is fixed to [1bit]. STOP BIT /DVR1/CAM1 DATA BIT /DVR1/CAM1 SYNC /DVR1/CAM1 BIT /DVR1/CAM1 Data STOP Bit (8bit) Stop (1bit Data Bit Bit (8bit)fixed) Sync Communication Data Bit (8bit) Speed (127,127,3) Stop Bit (1bit fixed) fixed) Stop Bit (1bit Speed (127,127,3) Speed (127,127,3) MOVE SPEED /DVR1/CAM1 STOP BIT /DVR1/CAM1 MOVE SPEED /DVR1/CAM1 Data Bit (8bit) Data Bit Bit (1bit (8bit)fixed) Stop Data Bit (8bit) SpeedSpeed Setting Stop Bit (1bit fixed) fixed) (127,127,3) Stop Bit (1bit Speed (127,127,3) 1. Select [Speed] option Speed (127,127,3) then press ENTER. The sub menu will appear. SYNC /DVR1/CAM1 MOVE SPEED /DVR1/CAM1 SYNC /DVR1/CAM1 Sync Communication Data Bit (8bit) Sync Communication Stop Bit (1bit fixed) Speed (127,127,3) 2. Set the Pan/Tilt/Zoom speed. SYNC Sync Communication 24 /DVR1/CAM1 1 Data Bit (8bit) Stop Bit (1bit fixed) Speed (127,127,3) STOP BIT /DVR1/CAM1 Data Bit (8bit) Sync Communication Setting Stop Bit (1bit fixed) Select [Sync Communication] option then press Speed (127,127,3) ENTER. Synchronize menu is for re-constructing H/W communication MOVE settingsSPEED between DVR and Camera con/DVR1/CAM1 nected to DVR. Data Bit (8bit) If user Stop can not the camera connected to Bit control (1bit fixed) DVR, please consider this option (pushing synchroSpeed (127,127,3) nize menu) CAMERA SETTING Manual Focus Speed Setting M PT PT 1. Select [Manual Focus Speed] option then press ENTER. The sub menu will appear. MANUAL FOCUS SPEED /DVR1/CAM1 PTZ Manual Focus Speed PTZ Home Position PTZ Position Reset [R /DVR1/CAM1 PTZ MANUAL FOCUS SPEED /DVR1/CAM1 M PT RE PT CAMERA SETTING SYNC PTZ /DVR1/CAM1 /DVR1/CAM1 Sync Communication LOW Speed MIDDLE Speed HIGH Speed MANUAL FOCUS SPEED /DVR1/CAM1 Camera Settings In this menu, you can customize the settings provided. Select the [COMMUNICATION] icon and press ENTER. CAMERA SETTING /DVR1/CAM1 MANUAL FOCUS SPEED /DVR1/CAM1 Manual Focus Speed PTZ Home Position PTZ Position Reset R Fa PTZ 2. Select a shutter Manual Focusspeed Speedfrom among LOW Speed, MIDDLE Speed, or HIGH Speed. PTZ Home Position PTZ HOME PositionPOSITION Reset PTZ /DVR1/CAM1 [R RE Manual Focus Speed PTZ Home Position PTZ Home Position PTZ Position Reset MANUAL SPEED /DVR1/CAM1 PTZFOCUS POSITION RESET The home position is the camera’s basic/DVR1/CAM1 position. LOW returns Speed to this position after executing The camera Manual Focus Speed Speed the [PTZMIDDLE HomePTZ Position] option. Home Position PTZ HOME POSITION /DVR1/CAM1 HIGH Speed 1. Select [PTZPTZ Home Position] Position Resetoption then press ENTER. [Go to Home] The subAre menu appear. you will sure? [R RE Re F Fa R Fa PTZ POSITION /DVR1/CAM1 PTZ HOME POSITIONRESET /DVR1/CAM1 RE Position] Manual[Reset Focus PTZ Speed Period : every _ Day PTZ Home Position (0, 1~90) PTZ Position Reset MANUAL FOCUS SPEED /DVR1/CAM1 LOW Speed MIDDLE Speed HIGH Speed [R F pa F PTZ HOME POSITION /DVR1/CAM1 REMOTE PTZ RESET /DVR1/CAM1 Re Fa [Go to Remote Home] PTZ Reset Are Factory you sure? Default [F 2. Press ENTER to confirm it. PTZ HOME POSITION /DVR1/CAM1 Manual Focus Speed PTZ Home Position PTZ Position Reset F REMOTE PTZ RESET /DVR1/CAM1 pa [Reset PTZ Camera] Are you sure? 25 PTZ HOME POSITION [Go to Home] /DVR1/CAM1 FACTORY RESET Remote PTZ Reset /DVR1/CAM1 [F MANUAL FOCUS SPEED /DVR1/CAM1 MANUAL FOCUS SPEED /DVR1/CAM1 LOW Speed LOW Speed MIDDLE Speed MIDDLE Speed HIGH Speed HIGH Speed PTZ Position Reset Factory Reset You can resetPOSITION the connected PTZ camera’s position PTZ HOME /DVR1/CAM1 PTZ HOME POSITION /DVR1/CAM1 automatically. Manual Focus Speed Speed Reset] option then press 1. Manual SelectFocus [PTZ Position PTZ Home Position PTZ Home Position ENTER. PTZ Position Reset ThePosition sub menu will appear. PTZ Reset You can reset the camera’s parameters to the factory REMOTE PTZ RESET /DVR1/CAM1 default settings. REMOTE PTZ RESET /DVR1/CAM1 [Reset PTZ Camera] PTZ Camera] option then press 1. Select[Reset [Factory Are you Default] sure? Are you sure? ENTER. The sub menu will appear. PTZ POSITION RESET /DVR1/CAM1 PTZ HOME POSITION Manual Focus Speed/DVR1/CAM1 PTZ HOME POSITION /DVR1/CAM1 PTZ Home Position [Go to Home] [Go toPTZ Home] Are you Position sure? Reset Are you sure? AM1 AM1 REMOTE PTZ RESET /DVR1/CAM1 REMOTE PTZ RESET /DVR1/CAM1 Remote PTZ Reset Remote PTZ Reset Factory Default Factory Default FACTORY RESET /DVR1/CAM1 FACTORY RESET /DVR1/CAM1 Remote PTZ Reset Remote PTZ Reset Factory Default Factory Default PTZ POSITION RESET /DVR1/CAM1 FACTORY RESET /DVR1/CAM1 FACTORY RESET /DVR1/CAM1 password : _ password : _ [Reset PTZ Position] Period : every _ Day (0, 1~90) PTZ POSITION RESET /DVR1/CAM1 2. Use number buttons to select the pattern index number then pressSpeed ENTER to confirm. Manual Focus • REMOTE 0PTZ : Disable the PTZ position reset. HomePTZ Position RESET /DVR1/CAM1 PTZ Position Reset • 1~90 : Reset the PTZ position once per numRemote PTZyou Reset ber of days set. Factory Default M1 AM1 M1 2. Enter the password and press ENTER. [Factory Default] [Factory Default] Are you sure? Are you sure? PTZ POSITION RESET /DVR1/CAM1 Remote PTZ Reset [Reset PTZ Position] You can reset the: connected Period every _ DayPTZ camera’s paramREMOTE PTZ RESET /DVR1/CAM1 eters to the(0, factory 1~90) default settings. [Reset PTZ Camera] 1. Select [Remote PTZ Reset] option then press you sure? ENTER.Are The sub menu will appear. M1 M1 REMOTE PTZ RESET /DVR1/CAM1 Remote PTZ Reset FACTORY RESET Factory Default Remote PTZ Reset Factory Default M1 M1 /DVR1/CAM1 REMOTE PTZ RESET /DVR1/CAM1 [Reset PTZ Camera] FACTORY RESET Are you sure? password : _ /DVR1/CAM1 2. Press ENTER to confirm it. FACTORY RESET /DVR1/CAM1 M1 26 Remote PTZ Reset Factory Default [Factory Default] Are you sure? 3. Press ENTER to confirm it. REFERENCE Camera Control Function Lens Control The following functions are available with cameras provided with controllable lens. Camera control functions are operable. It is necessary to set up the camera before using the camera control functions. For further information, refer to the Operating Instructions for the respective combination camera. You can also set it up from the Camera Setup menu during operating the system. 1 2 Pan/Tilt Control 3 A combination camera or an ordinary camera with pan/tilt head can be controlled. Move the pan/tilt head in the desired direction using the joystick. 1 1 Press the In button to optically bring the object closer, or press the Out button to optically widen the scene. Tip: Turning the joystick head to the right or left will zoom or widen the image. (The zooming level will go up or down.) Note: Focal length differs depending on the lens installed on the camera. 2 Press the Near or Far button to adjust the lens focus while watching the monitor. 3 Press the Open or Close button to adjust the lens iris while watching the monitor. 27 Specifications Communication Joy-Stick Type Signal RS-485 Connector RJ11 Baud Rate 1,200 / 2,400 / 4,800 / 9,600 / 19,200 / 38,400 / 57,600 / 112,500 bps 3-Axis 256 Camera ID / Protocol Selection / Alarm Control Pan / Tilt / Zoom / Iris / Focus 128 Positions Preset Touring Control 8 Positions Auto Panning 4 Pattern Settings Privacy Zone Masking (8 zones) LG DVR (LDV-S500 series, LE3100 series) key emulation (All function operated by DVR front key is supported). Connection CH1 Operating only TX mode CH2 Operating only RX mode (Using for controller cascade) Firmware Update RS-232C Total Key Number 44 Password 1~20 Digits Display 4 Gray Graphic LCD (256 x 72 dots) Operation Temp. / Humidity -10 °C ~50 °C / 0%RH ~ 80%RH Storage Temp. / Humidity -20 °C ~60 °C / 0%RH ~ 85%RH Supplied Voltage DC12V, 125mA Power consumption 1.5W Weight 1kg Dimension(H x V x D) 419 x 110 x 190mm P/NO : MFL30580188 P/NO : MFL30580188