E-mini Instant Water Heater M / End

Transcript

E-mini instant water heater M / END Application areas Single point supply: > Washbasin > Sanitary facilities in commercial buildings Subject to technical changes and version changes. Errors and omissions excepted. Date of publication: 09.17 Product information 1 / 4 E-mini instant water heater M / END Product information |  Energy efficiency class A  M 3 / END | M 3 (E) / END Part number: 1500-17243 | 1500-172432 Type: open-outlet (Scale: A+ to F) Water connections (thread connections): G ⅜" Hot water output at ∆t = 25 K [l/min]: 2.0 Switch-on flow rate / max. flow rate 2) [l/min]: 1.3 / 2.0 Nominal power rating [kW]: 3.5 1) Supply voltage [1~ / N / PE 230 V AC]: Nominal current [A]:    with plug | permanent connection 15 Required cable diameter [mm2]: 1.5 Bare wire heating system IES : ® VDE approved / Protection class:   / IP 25 Specific water resistance at 15 °C [Ωcm] ≥ : 1100 Nominal volume [litres]: 0.2 Weight filled with water [kg]: approx. 1.5 Dimensions (height × width × depth) [cm]: 1) Temperature increase e.g. from 15 °C to 40 °C 13.5 × 18.6 × 8.7 2)  Limited flow amount for optimal temperature increase. Can be adjusted via water amount adjustment. Description Profitability comparison  (Source: www.clage.com) >> Hydraulically controlled instant water heater (undersink model) with compact design for the energy-efficient hot water supply of a washbasin, with single-lever mixer tap Saves up to 85 % energy compared to conventional small storage heaters. >> The full heating capacity turns on automatically as soon as water flows through the unit >> Efficient flow technology for an optimum water jet and economical water consumption The E-compact instant water heater features an economical operation. The water is heated directly as it flows through the unit. Hot water is not stored in a tank, which saves standby energy that would be otherwise required. >> The efficient bare wire heating system IES® with replaceable heating cartridge provides an extended service life and easy maintenance >> Removable rating plate cover for access to the main hood screw and water volume adjustment – 85% >> Ready to use, vented design >> Set is easy to install with flexible steel hoses G ⅜ inch × 50 cm and power cable 60 cm >> Aerator insert for the tap is included conventional 5 litre storage heater Subject to technical changes and version changes. Errors and omissions excepted. Date of publication: 09.17 CLAGE E-mini instant water heater Product information  2 / 4 E-mini instant water heater M / END Installation Sample installation (open-outlet) Measurements in mm Assembly and operating instructions must be observed upon installation. 152 Using the aerator (included): CSP 3 111 105 max. 30 Ø 35 Angle valve outlet G ⅜" 135 ≤ 650 22 186 ≥ 70 75 Subject to technical changes and version changes. Errors and omissions excepted. Date of publication: 09.17 Angle valve approx. 550 Fastener approx. 520 133 Cable inlet approx. 553 Power plug approx. 700 Unit depth 87 Washbasin top edge approx. 850 – 950 (shorten cable if necessary) Installation  3 / 4 E-mini instant water heater M / END Accessories Aerator CSP 3 (included) The aerator at the tap supports the energy- and water-saving operation of the compact instant water heater. The new special CSP aerators mix air into the water and thus create a uniform water stream that does not splatter but softly cascades down. Aerator insert for tap adapter M 22/24 at the tap CSP 3 (< 2 l / min):Part no. 0010-00421 CLAGE GmbH Pirolweg 1 – 5 21337 Lüneburg Germany Phone +49 4131 8901-38 Fax +49 4131 2444771 [email protected] > www.clage.com Accessories  4 / 4