Transcript
CyberResearch® Industrial Panel PCs
CyRAQ Series E Panel PC with Flush-Mount Display ®
Quick Start Panel-Mounting Guide
Shown above: CYRAQ Series E Panel PC with 17" LCD Monitor
STEP 1
Mounting Hardware 1. (4) 6-32 x 1/4" trusshead screws (Phillips) 2. (4) M4 x 8 mm panhead screws (Phillips) 3. (4) 6-32 x 5/16" buttonhead screws (hex) 4. (1) 6" long 5/64" hex long-arm L-key 5. Monitor Mounting Clamps (number depends upon LCD size) 6. (1) LCD Mounting Plate 7. (1) PC Mounting Plate
Attach LCD mounting plate () to monitor using 4 M4 x 8 mm screws (). Place tabs (shown in detail below) toward the top of the monitor.
LCD Mounting Plate Tab Tab
CyberResearch, Inc. 25 Business Park Drive Branford, CT USA
Page 1 Rev 1.3 2 / 13 / 2008
Phone: (203) 643-5000 Fax: (203) 643-5001 www.cyberresearch.com
CyberResearch® Industrial Panel PCs
STEP 2
X mm*
Monitor Installation Y mm*
Insert monitor and plate into panel cut-out. Panel cut-out will vary depending upon monitor size: Monitor Size
Panel Cut-Out (W = width; H = height)†
12" 15" 17" 19" / 20" / 21" 24"
X = 312 mm (W); Y = 244 mm (H) X = 386 mm (W); Y = 302 mm (H) X = 384 mm (W); Y = 346 mm (H) X = 441 mm (W); Y = 356 mm (H) X = 596 mm (W); Y = 421 mm (H)
*dependent on monitor size; see chart at left
†
Panel-mount cut-out dimensions shown above are for flush-mount models only; panel cut-outs for universal-mount models may differ. Please refer to the documentation provided with your 19", 20", 21", or 24" universal-mount monitor for the appropriate cut-out sizes.
STEP 3
*NOTE: CyRAQ 24s use a compression mounting plate system. Please refer to the documentation provided with the CyRAQ 24 monitor for installation instructions.
Mounting Clamps* Install monitor mounting clamps () to secure monitor to panel.
CyberResearch, Inc. 25 Business Park Drive Branford, CT USA
Page 2 Rev 1.3 2 / 13 / 2008
Phone: (203) 643-5000 Fax: (203) 643-5001 www.cyberresearch.com
CyberResearch® Industrial Panel PCs
STEP 4 LCD Cable Connection Attach all cables to monitor (i.e. VGA or DVI video, power, and optional touchscreen).
STEP 5 PC Mounting Plate
PC Mounting Plate in Upper Position
Attach PC mounting plate () to monitor using 4 6-32 x 1/4" screws (). The PC mounting plate has two sets of 100mm VESA holes that allow you to mount the PC higher or lower on the monitor (lower position will allow more access to the monitor’s connector panel — see Step 8). Regardless of which mounting position is chosen, be sure to place tabs on the plate toward the top of the PC.
CyberResearch, Inc. 25 Business Park Drive Branford, CT USA
Tab
PC Mounting Plate in Lower Position
Page 3 Rev 1.3 2 / 13 / 2008
Phone: (203) 643-5000 Fax: (203) 643-5001 www.cyberresearch.com
CyberResearch® Industrial Panel PCs
STEP 6 PC Installation Mate PC assembly with monitor as shown.
STEP 7 Secure PC Secure PC to monitor using 4 6-32 x 5/16" hex screws () and long-arm L-key ().
CyberResearch, Inc. 25 Business Park Drive Branford, CT USA
Page 4 Rev 1.3 2 / 13 / 2008
Phone: (203) 643-5000 Fax: (203) 643-5001 www.cyberresearch.com
CyberResearch® Industrial Panel PCs
STEP 8 PC Cable Connection Attach video cable from monitor, PC power supply cable, optional touchscreen cable, and any other desired user interface cables to the PC.
CyberResearch, Inc. 25 Business Park Drive Branford, CT USA
Page 5 Rev 1.3 2 / 13 / 2008
Phone: (203) 643-5000 Fax: (203) 643-5001 www.cyberresearch.com
