Transcript
S19-120, S19-120A, S19-120SS Drench Shower with Horizontal Supply • Exceeds American National Standard Z358.1 Specifications • Exceeds European EN 15154-1 • Exceeds Australia/New Zealand AS4775 & AS/NZS 4020 • Easily Mounts to Wall • Galvanized Steel Protected with BradTect® Safety Yellow Coating
®
• Universal Identification Sign and Inspection Tag Included • Full, One-Year Warranty • SpinTec™ showerheads are covered by one or more of the following patents: 8113446; D594,089; D669,555; Reg. Comm. Des. D001079560-0001. Other patents pending. • Classified by Underwriters Laboratory Inc. to ANSI Z358.1 • Listed by Intertek to EN 15154-1 • Certified by IAPMO OCEANA to AS4775 and AS/NZS 4020
Specifications Impact-resistant plastic shower head is colored bright yellow for high visibility in emergency situations. Also available in corrosion resistant stainless steel. Shower pull rod is stainless steel. Galvanized steel piping is additionally protected with BradTect® safety yellow coating. Model S19-120SS is all stainless steel construction.
Model S19-120
Drench shower is designed to accommodate standard 8' ceiling height. ANSI
Z358.1 compliant drench showers are mounted between 82"–96" from the lower edge of the showerhead or shroud to the floor.
This plumbing fixture is not intended to dispense water for human consumption through drinking or for preparation of food or beverages.
Model Description S19-120
Drench Shower w/Horizontal Supply, Plastic Showerhead
S19-120A
Drench Shower w/Horizontal Supply, Plastic Showerhead w/ Stainless Steel Shroud
S19-120SS
Drench Shower w/Horizontal Supply, All-Stainless Steel Fixture
S19-120SSZ Drench Shower w/Horizontal Supply, All-Stainless Steel Fixture w/ BSPP Connection/Certified to AS4775 & AS4020 S19-2100
Navigator EFX25 - Emergency Thermostatic Mixing Valve
Model S19-120A
Recommended Option: Navigator S19-2100 EFX25 Emergency Thermostatic Mixing Valve
Model S19-120SS Satisfies ANSI Z358.1 tepid water requirements.
Page 1 of 3 11/2/2015 This information is subject to change without notice. Bradley_DrenchShower_S19-120_A_SS
© 2015 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309 800 BRADLEY (800 272 3539) +1 262 251 6000 bradleycorp.com
S19-120, S19-120A, S19-120SS Drench Shower with Horizontal Supply Standard Equipment SpinTec™ Showerhead Standard showerhead is 3.1" (78.7mm) diameter highly visible yellow impact-resistant plastic (Model S19-120A includes a 10¾" [273mm] diameter corrosion-resistant stainless steel shroud). High performance corrosion-resistant stainless steel showerhead measures 1½" (38mm) in diameter (Model S19-120SS only). SpinTec drench showerhead features integral 22 GPM (83.3 L) flow control, conserving water and helping to accurately size your tepid water system.
Valve Chrome-plated brass 1" NPT stay-open ball valve, operated by stainless steel pull rod with triangular handle. Model S19-120SS is all stainless steel. Pipe and Fittings 1¼" galvanized steel with BradTect® safety yellow coating. S19-120SS is all stainless steel. Water Supply 1" NPT Horizontal.
Local codes may require the installation of a backflow prevention valve to
complete proper installation. Compliance with local codes is the responsibility of the installer. Valve must be tested annually to verify that it is functioning properly. Backflow prevention valves are not included with the fixture and may be supplied by the contractor or purchased from Bradley Corporation.
SpinTec Flow Rate vs Inlet Pressure at Fixture 40
Flow Rate (gpm)
35 30 25 20 15 10 5 0 10
20
30
40
50
60
70
80
90
Inlet pressure at Fixture (psig)
Page 2 of 3 11/2/2015 This information is subject to change without notice. Bradley_DrenchShower_S19-120_A_SS
© 2015 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309 800 BRADLEY (800 272 3539) +1 262 251 6000 bradleycorp.com
S19-120, S19-120A, S19-120SS Drench Shower with Horizontal Supply S19-120
S19-120A 15¾" (400mm)
15¾" (400mm) 35⁄8" (92mm)
4½" (114mm)
6" (152mm)
25½" (648mm)
Ø 3.1" (78.7mm)
35⁄8" (92mm)
Ø 10¾" (273mm)
84" (2134mm) to floor
84" (2134mm) to floor
9" (229mm)
25½" (648mm)
9" (229mm)
S19-120SS 15¾" (400mm) 35⁄8" (92mm) 3¾" (95mm) 25½" (648mm)
1½" (38mm) 84" (2134mm) to floor
9" (229mm)
All dimensions assume standard thread engagement. Variations in manufacturing allow for +/- 1⁄8" (3mm) per threaded joint. To find the tolerance of a dimension, add the number of thread joints in between a dimension and multiply it by 1⁄8" (3mm).
Page 3 of 3 11/2/2015 This information is subject to change without notice. Bradley_DrenchShower_S19-120_A_SS
© 2015 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309 800 BRADLEY (800 272 3539) +1 262 251 6000 bradleycorp.com
