Transcript
2011 说明书封面应该由产品决定！
Easy7 Video Monitoring System User Manual
Easy7 Video Monitor System
User Manual V2.0
Contents 1,Introduction ........................................................................................................................... 4 1.1 Intention ................................................................................................................................4 1.2 Terms and abbreviations ...................................................................................................4 2,Standard File Reference ...................................................................................................... 4 3,Software Overview ............................................................................................................... 4 3.1 Software Use ........................................................................................................................4 3.2 Software Running ................................................................................................................5 3.3 Operating System ...............................................................................................................6 4,Software Installation and Uninstallation ............................................................................. 6 4.1 Software Installation ...........................................................................................................6 4.2 Software Uninstallation .....................................................................................................10 5,System Settings Instruction ................................................................................................ 12 5.1 Authority Management ...................................................................................................12 5.2 Device Management ......................................................................................................16 5.3 Video Setup ........................................................................................................................32 5.4 Decoder Setup ..................................................................................................................35 5.5 Switch setups ......................................................................................................................38 5.6Alarm Linkage .....................................................................................................................40 5.7 Log .......................................................................................................................................50 5.8 Other Settings.....................................................................................................................51 6,Client instructions ............................................................................................................... 53 6.1 Log guide ............................................................................................................................53 6.2 Video Preview ....................................................................................................................55 6.4Review the downloaded ..................................................................................................61 6.5 Local Storage .....................................................................................................................68 6.6 Log Management .............................................................................................................69 6.7 Matrix Control ....................................................................................................................71 6.8 Keyboard Management .................................................................................................78 7,Remote Control................................................................................................................... 79 7.1 Tiandy Device Remote Control ......................................................................................79
1,Introduction 1.1 Intention This Manual based on Easy7 video monitoring system CS client code to provide briefly explanation, helping the users to learn the operation process.
1.2 Terms and abbreviations None
2,Standard File Reference Omit
3,Software Overview 3.1 Software Use This software can be used as a subsystem of Easy7 monitoring platform, also can be installed and used independently. 1,When using as a subsystem of Easy7 monitoring system, it enables operations in CS client end: Audio/Video Overview and Switch, Device Control, Manual Recording, Snapshot, Viewing Alarm Information, Checking logs and Records Playback after CMS setting. 2,When using independently, it enables User authorization setting, Device Management, Devices Remote Setting, Decoding Management, Switching Management, Record Module Setting, Alarm Activation Setting, also can be used as a Recording Host for Timing Recording.
3.2 Software Running This software is divided into three versions. 1,Easy7 Client Express V2.0T(Build1008).EXE. Independent installation operation, support whole series of Tiandy DVR and network video devices, with maximum ability of connection with 64 devices or 128 channels. 2,Easy7
Client
Professional
V2.0T(Build1008).EXE.
Independent
installation
operation, support whole series of Tiandy DVR and network video devices and PC digital video recording systemV6.9, Hikvision mainstream embedded host, Kikvision HD IPC device, Hikvision behavior analyzing device, Dahua Embedded Host. With Maximum ability of connection with 128 devices or 256 channels. Operation requires encryption dog, no encryption dog software can only run 60 minutes. 3,Easy7 Client.NET V2.0T(Build1008).EXE. Need to run with Easy7 Monitoring platform. Setting Devices information in CMS module in Easy7 Monitoring platform. Operation requires encryption dog, no encryption dog software can only run 60 minutes.
3.3 Operating System Service End: Operation System: Red Hat Enterprise Linux5.0 system or above; CPU: Xerox Dual Core 2.4GHz or above; RAM: DDR3 2G or above; Hardisk: At least 80G; Network Card: 100/1000M self-adaptable type Clients End: Operation System: Microsoft Windows xp or Windows7 system; CPU: Dual Core 2.4GHz or above; RAM: DDR2 2G or above; Hardisk: At least 40G; Network Card: 100/1000M self-adaptable type
4,Software Installation and Uninstallation 4.1 Software Installation Take example of “Easy7 Client Express V2.0T(Build1008).EXE” installation in Microsoft Windows XP system. The operation is the same for the other two versions. 1,Find setup file in the disk of :”Easy7 Client Express V2.0T(Build1008).EXE”
2,Double Click to enter setup process.
3,Select language, click “Next”.
Default setup folder is in Disk C, it is available for customized setup folder, click “Next” to the end.
4,Click “Finish”, the system will install Visual C++ 2008 module automatically, it is a necessary component. Click “Next -> Install -> Finish” according to the instruction to the end of the process.
4.2 Software Uninstallation 1,Select Open Menu in Windows system, “Open Menu”-> “All Program” -> “Tiandy” -> “Easy7 Client Express V2.0T(Build1008)”-> “Uninstallation”
2,Click “Yes”, the uninstallation program will terminate the running software of all related Easy7 programs to continue the uninstallation process.
3,Click “Next”-> “Finish” according to the instruction to finish the uninstallation.
4,It will also uninstall the Visual C++ 2008 module in the uninstallation process, select “Uninstall” and click “Next -> Finish” according to the instruction to finish the uninstallation.
5,System Settings Instruction 5.1 Authority Management 5.1.1 User Management Click 【user management】 to user management interface, and it displays all users’ basic information added in the current system, as shown in Figure 5-1
Figure 5-1
5.1.1.1 Add User Click 【Add】 into the add user interface, as shown in Figure 5-2
Figure 5-2 【User Name】: Input any users name here. (Below illegal characters are not allowed: -~!#$%^()=[]{},":;'<>?*`+/\) 【Effective Time】Users can set effective time for the newly added users. 【Password】: Password for the user. 【Confirm Password】Input the same password as “password”. 【Memo】: Memo information for the user. 【Role to User】: roles for current user. 【All Roles】All roles for current system.
5.1.1.2 Modify User Select a user, and click 【Modify】to the interface, as shown in Figure 5-3
Figure 5-3 Administrators can modify the user name, password, and authority, and the specific settings are the same as adding users.
5.1.1.3 Delete User Select one or more users, and click 【Delete】 to delete the selected user.
5.1.2 Role Management Click 【role management】 to role management interface and it displays the current all the basic users’ information that have been added, as shown in Figure 5-4.
Figure 5-4
5.1.2.1 Add Role Click 【Add】to the role edit interface and add necessary information in 【role name】 and 【Description】. Click 【Confirm】 to add the role to complete. In the role list, select the newly added role, and on the right side, the authority tree occurs. Tick the appropriate authority, and click 【set】to complete the setting.
5.1.2.2 Modify Role Select any character, and click 【Modify】, dialog box will pops up and it is basically the same as adding role.
5.1.2.3 Delete Role Select any one or more roles, and click 【Delete】, you can delete the selected role.
5.1.2.4 Role Authority Setting Tick the box in front of the authority and click【set】to set authority for current
selected roles, as shown in Figure 5-5.
Figure 5-5
5.2 Device Management 5.2.1 Host Management Click 【Host Management】 into the host management interface, and it displays all the hosts and its channels, alarm ports that have been added, as shown in Figure 5-6
Figure 5-6
5.2.1.1 Add Host There are 2 ways to add host, individual adding and intelligent adding, shown below as figure 5-7, 5-8:
Figure 5-7
Figure 5-8 Individual Adding: Click【Add】to pop up interface for adding video host, shown below as Figure 5-9
Figure 5-9 Host Information: 【Host Name】Add host name.(Host name are not allowed to input below illegal characters-~!#$%^()=[]{},":;'<>?*`+/\) 【Serial No.】Add the host's serial number 【Host ID】When select 【Automatic ID】, the system will automatically generate a random system-wide unique ID; when the【auto-ID】 is not selected, you can enter your own defined ID to add (This ID shall not duplicate with the existing ID, otherwise it will fail). 【Host IP】Add host IP. 【IP Segment】When 【IP segment】 is ticked, user can batch add host IP. For example: Add 【Host IP】 as 1.1.1.1, and the IP segment as 1.1.1.20 and hosts from 1.1.1.1 to 1.1.1.20 of the 20 will be added. 【Host Port】Add the host communication port. 【Video Channel】Add the total number of video channels for the host. .
【Alarm Input Number】Add the total number of video channels for the alarm input ports. 【Alarm Output Number】Add the total number of video channels for the alarm output ports. 【Host Type】Choose the type of host: TD Series (Tiandy Series), DH Series (Dahua series), DS series (Hikvision series) and PC-type DVR 【User Name】Add the host username. 【Password】Add the host password. Proxy Information: 【Proxy Type】Select 【Empty】, 【Common Proxy】 or 【Middleware Proxy】 【No】——Proxy no required. 【Common Proxy】——If it is only through the first level proxy, used only need to input IP and port number for the first level proxy. If it is through the second proxy port, user needs to input IP address and port number for both the first level and the second level proxy.
Figure 5-10 【Middle ware Proxy】——Input【Client end MS IP】,【Client end MS port】, 【Client end MS ID】,【Client end MS name】,【server end MS IP】,【server end MS port】,【server end MS ID】 and 【server end MS name.As figure 5-11 Note:When going through middleware proxy, user needs to input host ID manually and keep the same as middleware host ID.
Figure 5-11
Domain Information: 【DNS type】: Four types here: 【Forbidden】,【Standard】,【Special】, 【Initiative】 【Forbidden】Do not use domain analysis or active mode. 【Special】: Taindy network. 【Standard】:Standard domain name analysis. Add separately【DNS IP】 【DNS , Port】, 【DNS domain name】,【DNS user name】and 【DNS password】. Shown as figure 5-12:
Figure 5-12 【Initiative Mode】:Active connection mode. Add separately【DNS IP】【DNS , port】, 【DNS domain name】,【DNS user name】和【DNS password】.Figure 5-13
Figure5-13 Note:When using domain name, set【Host IP】 as empty. Host Description: This is to add simple description for host. Complete the above information, and click 【 confirm 】 to add the host successfully. Click 【Cancel】 to exit the add interface. Intelligent Add Click【Add host intelligent】 to pop up the interface as figure 5-14
Figure 5-14 In the interface, system will show the host available to add automatically, users can select one or more. Click
to finish the adding as Figure 5-15
Figure 5-15 Select the host in the right list and click
and those you do not want to add
will remain.
5.2.1.2 Host Information Modify In host management, the system provides 2 ways to modify host information,
which are single modify or batch modify, shown as Figure 5-16, 5-17
Figure 5-16
Figure 5-17 Single Tick: When ticking a sing one, and clicking【Modify】, user will enter the modify interface for a single host, shown as figure 5-18
Figure 5-18 System will automatically add basic information of select host, after add new information, click 【enter】to complete revision. This operation is basically same as add host. Note: when revise host, host ID is not available to revise. If selected host ID is automatically generated, then if an agent is set, the revision will not affect. Mass revision: when select multiple hosts, click【mass revision】to enter host information interface, figure 5-19
Figure 5-19 At this time system will take the first select host information as default to add into coordinate blank, for user to revise. 【host port】Add coordinate host port. 【connect type】Two protocols available, TCP and UDP.
【agent type】No agent, normal agent, mid agent available. 【normal agent】: If through first class agent only, then just fill in 【first class agent IP】and 【first class agent port】 . If a second class agent is needed, then【first class agent IP】 【first class agent port】 【second class agent IP】and 【second class agent port】are all needed to be filled. 【mid agent】: Fill in 【customer end MS IP】,【customer end MS port】,【customer end MS ID】, 【customer end MS name】,【service end MS IP】,【service end MS port】,【service end MS ID】and【service end MS name】. 【protocol type】6 protocols are available: PTZ_PELCO_P,PTZ_PELCO_D,PTZ_TC615_P,DOME_PELCO_P,DOME_PELCO_D, DOME_TIANDY. In order to control front end equipment like PTZ, protocol must be same.
5.2.1.3 Host delete When select one or more host, click【Delete】, system will remove the selected hosts. As shown on Figure5-20 when toggle one or more host, click 【Delete】, then the selected hosts will be deleted.
Figure 5-20
5.2.1.4 Host search Host search: when click 【host search】, to enter host search interface. Figure 5-21
Figure 5-21 System provides two types of search, by host name and by video passage. 【search by host name】: could fill in host name, host IP or only one of them, click 【enter】,system will search qualified equipment, and system support cloud search. If information filled by user is uncompleted, system will list all host qualified, and notice user that the host list is a search result, search condition on the right is being toggled. Cancel toggling; system will display all the information of the hosts. Figure 5-21. 【search by video passage】: could fill in passage name, click 【enter】,system will search qualified equipment, and system support cloud search. If information filled by user is uncompleted, system will list all host qualified, and notice user that the host list is a search result, search condition on the right is being toggled. Cancel toggling; system will display all the information of the hosts. Figure 5-22.
Figure 5-22
5.2.1.5 Select convert Click 【select convert】, to convert the selected host.
5.2.1.6 Page up/down When the quantity is large, all the host will be displayed by pages, 13 items per page.
5.2.2 Video passage When select a host, video passage list will display all the passage information of the selected host. Figure 5-23
Figure 5-23
5.2.2.1 Add passage Click 【add】down the video passage list, to enter video passage interface. Figure 5-24
Figure 5-24
System will automatically fill in all the information of the host into coordinate blank. 【passage name】——Fill in the name of new added passage of the host. 【passage number】 ——Add new passage number of the host, could not be same as passage number exited. 【host name】——Automatic add selected host name, revision unavailable. 【host IP】——Automatic add selected host IP, revision unavailable. 【connect type】——Two types available, TCP and UDP. 【code stream type】——Two types available, main code stream and secondary code stream. 【protocol】——6 types available, PTZ_PELCO_P,PTZ_PELCO_D, PTZ_TC615_P,DOME_PELCO_P,DOME_PELCO_D,DOME_TIANDY.In order to control front end equipment like PTZ, protocol must be same. 【PTZ address】——pick up any number among 1-255, in order to control front end equipment like PTZ, address must be same as PTZ address. 【series interface number】——3 types available, 232,485-1,485-2. In order to control front end equipment like PTZ, series interface number must be same as PTZ address. 【control type】——2 types available, protocol and transistor passage. System supports both type, could be customized. 【cache size】——Could be set by user 【time delay】——User set. 【control speed】——User set, 1-7, lowest to fastest. 【passage description】——Could be filled by user.
5.2.2.2 Passage revision select a passage in the list, click 【revise】to enter passage revision interface, figure 5-25
Figure 5-25 System will automatically fill the basic information of selected passage in coordinate blank. Passage information revision method is same as passage addition.
5.2.2.3 Passage delete Select one or more passages, click 【delete】, selected passages will be deleted.
5.2.2.4 Select invert Click 【select invert】to invert the selection of passages
5.2.3 Alarm port When select a host in host list, alarm port list will show all information of alarm port of selected host. Figure 5-26
Figure 5-26
5.2.3.1 Addition of alarm port After select the host which you want to add alarm port, click 【add】to enter alarm
interface, figure 5-27
Figure 5-27 At this time, the basic information of the alarm port is filled in coordinate blank automatically. 【alarm port type】——Two types available, alarm input port and alarm output port. 【alarm port name】——Could be filled by user. 【alarm port number】———User could fill the the alarm port number freely, but the number could not same as existed port number. 【host name】————Filled automatically, revision not available. 【host IP】—————Filled automatically, revision not available. 【alarm port description】——Could be filled by user.
5.2.3.2 Alarm port revision After select alarm port in alarm port type list, click 【revision】, to enter alarm port revision interface, figure 5-28
Figure 5-28
.Alarm port information will be filled in box automatically by system to users revise. System just supports revising the alarm port name, alarm port no and alarm port. After revising, click the 【OK】to finish.
5.2.3.3 Delete Alarm Port Select one alarm port or more, and then click 【delete】 to delete.
5.2.3.4 Inverse Click 【Inverse】 to inverse alarm port in the list.
5.2.4 Group Management Click 【Group Management】, then whole device information and user-defined information will be show up. As Figure 5-29.
Figure 5-29 All added host and channels that released system automatically are on the left list. User-defined group information is on the right list. Users can add host on the left list to user-defined group on the right list. Such as: Add all channel of device 30.30.30.121 to user-defined group on the user-defined list. Step by Step: 1, Select all channel of 30.30.30.121 on the list. 2, Select user-defined group on the user-defined list.
3, Click
to add it.
4, Or use mouse to drag all channel of 30.30.30.121to user-defined group on the right list. As Figure 5-30
Figure 5-30 Select device channel in the user-defined group click
to delete. Or use
mouse will customize the points need to delete a group of dragging out right list. Remark: The client-side host list is loading the user-defined group information, so users must add device to user-defined group. Then users could find host channel in client-side of Easy7.
5.2.5 Remote Control Click【Remote Control】to enter, all device in the system and log status will be show up. Select login device and click “Remote Control” button to control.(Details in Chapter 7, Remote Control) Remark: Remote control just supports login device and Tiandy device.
5.3 Video Setup Users can setup video strategy as the situation.
5.3.1 Video Template Setup Click 【Video Template】to enter, added templates information are on the left list, as Figure 5-31
Figure 5-31
5.3.1.1 Add Template 【Template Name】——User can write template name, new name must be different
from
old
ones.(Template
name
can’t
include
-~!#$%^()=[]{},":;'<>?*`+/\) 【Starting Time】——User input starting time of this template. 【Ending Time】——User input ending time of this template. After that, click 【add】, then new added template is in the available template list.
5.3.1.2 Template Revise Select template on available template list, then original information will be show in related position. At this time user could edit template information and click 【Revise】 to finish.
5.3.1.3 Template Delete Select one template and click 【Delete】. Whether really delete selected template messages will be show up and click 【Yes】 to delete.
5.3.1.4 Template Application 【Video Type】Five alarm type, regular video, mobile alarm video, port alarm video, lost alarm video and other alarm video. User selects a video and click a template on the list, meanwhile all channel information and template will be displayed one to one. According to actual needs, users can check template before related channel. Click 【Save setup】to finish. 【Check all】Select all channels. 【Inverse】Inverse function.
5.3.2 Video Time-table Setup 5-32 Click 【Video Time-table】to enter setup interface. All templates are in the left list, selected template is in the right list. As Figure 5-32
Figure 5-32 According to user’s real demand to select template in the left list, and then select date when using video template in 【Date】box, click
to finish. Click
to delete. Select one template in 【Apply to every day】 to apply template to every day. If you select used template, it will be delete in template of apply to every day
5.3.3 Video Strategy Setup Click 【Video Strategy】, disk information will be show up in left list. Right side is area of strategy setup. As Figure 5-33.
Figure 5-33 User can check local video store disk in left side of local disk information. Setup
continuous recording time in 【continuous recording time】(from 5-120 min). Select percentage or (G)in 【Mini disk space】and write related parameter. Select video format in 【Save file format】. Delete previous video or stop recording in 【Disk Full】. After these steps, click 【Save Setup】to finish.
5.4 Decoder Setup 5.4.1 Decoder Input Decoder input as Figure 5-34.
Figure5-34 【Screen Name】——Input decode screen name 【Screen Type】——.Set different screen image segmentation display. 【Screen Tree】——User can select different kind of image segmentation when check a new screen. Click 【OK】to select 【Window X】in screen tree. Select different channel in right decoder channel. As Figure 5-35
Figure 5-35
5.4.2 Decoder Output Decoder output as Figure -36.
Figure5-36 【Decoder Output】——Select decoder output in dropdown list. 【Single View】——Decoder output as single view display. 【Two View】——Decoder output as two single view display. 【Four View】——Decoder output as four view display.
【Zero View】——Decoder output as zero view display. 【Decoder Input】——Display available decoder input.
5.4.3 Encoder Encoder, as Figure 5-37.
Figure 5-37 【Add】——Click to add a decoder, as Figure 5-38.
Figure 5-38 【Intelligent add】——Search decoder in LAN automatically and add, as Figure 5-39.
Figure 5-39 【Revise】——Revise decoder information, as Figure 5-40.
Figure 5-40 【Delete】——Decoder has been added to delete.
5.5 Switch setups Click【Switch setups】to enter setup menu,see to Figure 5-41
Figure 5-41 The main function is to switch the setting to switch the user to set their own way for so Easy7 video browsing, the client can automatically switch video channels, user-friendly browsing. 【 Number 】 ——Corresponding Easy7 client interface, video browsing video browser window number, for example: Monitor No. 1 represents Easy7 client video browsing interface for video browsing window 1, and so on. After adding the new policy name, right-click the policy name, right-click menu appears【add time periods】,see to Figure 5-42
Figure 5-42 Click【add time periods】to enter the time period setup options,see to 5-43
Figure 5-43 Users can set the actual time accoding to his requirements. Click【Confirm】to complete.See to Figure 5-44
Figure 5-44 After adding the time period, to the time the user can insert one or more host channel, the method is very simple device list on the left select the channel you want to add the right change strategy time period selected in the list, then click Can add to complete. Note: In a switching strategy can also add multiple switching time period, each time period can also add more than one host channel. 【Time Switch】——Users can browse the practical need to fill the video
monitor switching time, the system defaults to 30 seconds, switch the time frame set by the user is (30-7200) s
5.6Alarm Linkage Click【Alarm Linkage】to enter the Alarm Linkage setup menu,see to Figure 5-45
Figure 5-45 At this point, the user can according to actual needs, any host on the list of devices to any channel set the alarm linkage program.Double-click the device list in any channel, the channel's basicinformation is added to the right side of the 【current device】 and in their【respective hosts】, see to Figure 5-46
Figure 5-46 After adding
the host
and
the channel,
【
alarm
type】 and 【linkage type】 drop-down menu becomes enabled. 【alarm type】——Users can select the alarm type according to actual needs, Alarm types include:
Video loss Alarm, Video Loss Alarm elimination, Video Motion alarms, Video, Mobile consumer alarm,
Video, Alarm and
Video shielding block
elimination police. 【 Linkage
type 】 ——Users
can choose based
on
the
actual situation
of interaction types, interaction types, including: electronic linkage Map action, SMS notification linkage, linkage video started recording the end of linkage, linkage voice, video linkage, linkage and linkage pre-bit output. Note: The linkage alarm recording is available only in the beginning, the end of linkage only in the consumer alarm video when available. 5.6.1 Add Alarm Solution 【 Linkage Programme Office users 】
can edit the
selected type
ofthe
associated linkage set the alarm. 5.6.1.1Linkage map action When you select Action 【Linkage Map Click】 【Add Time】 to enter the setting interface linkage Map, See Figure 5-47
Figure 5-47 【 Name 】
action - added action
name. (name
of
the
action when
added illegal character limit, enter the following characters are not allowed -~!#$%^()=[]{},":;'<>?*`+/\) 【device】 - the user can choose to be joint hosts and channels. Click Select, the pop-up host channel
Selection interface, as shown in Figure 5-48
Figure 5-48 【Type】 linkage - linkage map user-selectable electronic means. After the above settings, click 【OK】 to add a success.
5.6.1.2 Linkage Short Message SMS notification when you select 【Linkage】 【Add Time】 click to enter the joint SMS notification settings interface, as shown in Figure 5-49
Figure 5-49
【 Name 】 action - added action name. (name of the action when added illegal character limit, enter the following characters are not allowed -~!#$%^()=[]{},":;'<>?*`+/\) 【SMS center number】- Enter the system default SMS center number 13800220500, the user can modify the actual situation. 【phone number】 - users fill out to receive alarm informationphone number. 【SMS messages】 - users can fill out at the purpose of the phone to
send alarm information content. After the above settings, click 【OK】 to add to complete.5.6.1.3
Start video linkage When you select【Start linkage】when the video click the【Add】, began to set into the linkage video interface, as shown in Figure 5-50
Figure 5-50 【 Name 】
action - added action
name. (name
of
the
action when
added illegal character limit, enter the following characters are not allowed -~!#$%^()=[]{},":;'<>?*`+/\) 【 Camera 】 ——Users
can
choose to host video linkage. Click Select, the
pop-uphost channel selection Interface, see to Figure 5-51
Figure 5-51 【Video Length】——The actual situation of the user can set (5-7200) seconds of the video duration. System The default recording duration of 5 seconds. After the above settings, click 【OK】 to add to complete.5.6.1.4 When you select the 【end linkage】 when the video click the【Add】, enter the linkage end video setup interface, see to Figure 5-52
Figure 5-52 【 Action
Name 】 ——added action
name. (name
of
the
action when
added illegal character limit, enter the following characters are not allowed -~!#$%^()=[]{},":;'<>?*`+/\) 【 Camera 】 ——Users can pop-up host channel selection Interface, as shown in Figure 5-53
choose to host video linkage. Click
Select, the
Figure 5-53 After the above settings, click 【OK】 to add to complete.5.6.1.5 When you select the 【sound Linkage】Add Time click to enter the joint sound settings interface, see to Figure 5-54
Figure 5-54 【Movement Name】——Add movement name.(Add the names of illegal action when the character limit, enter the following characters are not allowed -~!#$%^()=[]{},":;'<>?*`+/\) 【Audio File】——Users can choose to add wav format audio files. After done the settings, click【confirm】to finish.
5.6.1.6 Linkage video Click 【add】when the user chooses 【Linkage video】and enter the setting menu of Linkage video.
Figure 5-55 【Movement Name】——Add action name. (name of the action when added illegal character limit, enter the following characters are not allowed -~!#$%^()=[]{},":;'<>?*`+/\) 【Camera】——Users can choose to host video linkage. Click Select, the
pop-up host channel selection interface, see to Figure5-76
Figure 5-56 After the above settings, click 【OK】 to add complete.
5.6.1.7 Trigger Output Choose “Trigger Output” , click “Add” into the setting interface.
Figure 5-57 【
Motion
Name
】
——Add
the
motion
name(not
allow
input
-~!#$%^()=[]{},":;'<>?*`+/\) 【Output】——User can choose output points of trigger host, click “Select”, show the “Device List”,
Figure 5-58 After finish setting ,click “OK”.
5.6.1.8 Trigger Preset Position Choose “Trigger Preset Position”, click “Add” into the trigger preset position setting interface.
Figure 5-59 【
Motion
Name
】
——Add
the
motion
name(not
allow
input
-~!#$%^()=[]{},":;'<>?*`+/\) 【Camera】——User can choose output points of trigger host, click “Select”, show the “Device List”,
Figure 5-60
5.6.2 Trigger Configuration Modify In the trigger configuration edit list choose a alarm trigger configuration, click “modify” into the edit window, and click “OK”
5.6.3 Trigger Configuration Delete In the trigger configuration edit list choose one or more alarm trigger configuration. Click “Delete”
Figure 5-61
5.7 Log Click into the log manage interface.
Figure 5-62 【Auto Delete】——Set log keep days 【Write Log Set】——Choose which logs to recorded.
5.8 Other Settings Other settings include: keyboard manage, other setting and open client express
5.8.1 Keyboard Management Click “Keyboard management”
Figure 5-63 Double click the channel line, can modify the channel number.
5.8.2 Others Setting Click “Other Settings”
Figure 5-64 【Auto Run】——User fill the user name and password, EASY 7 will auto run when the operation system run. 【Auto run device】——The front-end device will auto login after EASY 7 client run. 【auto resume last screen type】——Resume the last screen state when re-login. 【show tip】——It will show the information in the right corner when the device online or outline. 【Emap on two screen】——Electronic map can achieve dual screen display. 【auto revise time】——Ghost auto time revised. 【main title】——Set main window title name. 【capture path】——Modify the link of capture 【GSM modem baud rate】——Choose correct baud rate. 【GSM modem serial NO.】 【Save settings】 【Reload settings】 【System backup】 【System restore】
5.8.3 Open Client Click “Open client” into the client.
6,Client instructions 6.1 Log guide 6.1.1 Client login
Double click EASY 7 client
into the system login interface.
Figure 6-1-1 NOTICE:Default user name and password is : admin, 1111. 【Login Sytemset】 【More】——Modify the user name and password 【Cancel】
6.1.2 Client Login Double click the EASY 7 CLIENT.
Figure 6-1-2 First login, need to click “Advance” into the IP set interface (as 6-1-3), set the IP address and interface, When the first login, it need to click “Always update CMS”. The second time log, can cancel this option.
Figure 6-1-3 Click “Return”, return client. 【Log system set】 Input correct user name and password. 【Cancel】
6.2 Video Preview Main interface includes: tool bar, ghost list, video browse window, PTZ control, alarm prompt.
Figure 6-2
6.2.1 Video Preview Window Video browse window, double click to maximum
Figure 6-3 The right corner show the channel name.
Figure 6-4
6.2.2
Video browse drag and compart function
Video browse window can drag any size, hold mouse left button to drag can change the video browse window size.
Figure 6-5
6.2.3 Video Browse Tool Bar Video Capture:
Edit Mode button, the map can be edited after click this button.
Left Move button, the map will be move to left after click this button.
Up Move button, the map will be move to up after click this button.
Right Move button, the map will be move to right after click this button.
Down Move button, the map will be move down after click this button.
Zoom In button, the map will be zoom in after click this button.
Zoom Out button, the map will be zoom out after click this button.
Reset button.
Show button, eagle eye will be show on the map right corner.
Hide button, eagle eye will be hide on the map.
Show toolbar button, click on the toolbar can be displayed on the left.
Hide toolbar button, click to hide on the left toolbar
Import button, the map can be saved for import.
Export button to export a backup of the current map.
Personalized Settings button, you can set
the width and height of Eagle Eye, in the above query edit box enter the label can be on the map, query results centered. The center button to set the map center coordinates, click the Reset button, the map automatically jump to the center position.
6.3.2 Direction and rate of operation
Figure 6-17 The part of the map can move up, down, left, right, zoom in and out functions. Click
to move the map upwards.
Click
to move the map downwards
Click
to move the map to the left.
Click
to move the map to the right.
Click
to zoom in the map.
Click
to zoom out the map.
drag the map up and down can control the zoom
6.3.3 Right click menu of the map
Figure 6-18 【point labels】 to add video surveillance video surveillance points can be added
. 【 Enter
labels
to
add 】
alarm
alarm
input
tags
can
be
added
. 【 Add alarm Tags 】 output Alarm output tag added at the beginning
. 【remove tags】 have been added to remove the label.
6.3.4 The menu of right click the layer
Figure 6-19 【to add a digital map】 layers to add a digital map layer.
【Delete】 to delete the electronic map layer of an electronic map of the selected layer.
6.3.5Map settings
Figure 6-20 【Name】 layer can modify the layer name. 【Address】 layers layers can be associated with the Figures. 【to zoom enlarge】 the selected layer. 【Narrow selected】 layers can be reduced. 【to move】 the Move the selected layer. 【Down】 to move down the selected layer. 【Zoom】 largest representative of the maximum aspect ratio of the layer, more than the proportion of the layer hidden. 【Zoom】 least the minimum on behalf of the layer aspect ratio, this ratio is lower than the layer hidden. 【layer associated channel, select】 can be monitored, respectively, points, alarm points and channel labels, alarm input and output associated with it. 【Save】 can be done to save the settings.
6.4Review the downloaded
Figure 6-21 As shown in Figure 6-21 playback interface, the main window by the playback, playback control, browse and download a few parts.
6.4.1 Record require Download the playback unit of a query interface on the right, select the 【storage location】, storage location, including front-end storage, centralized storage, local
storage. Figure 6-22
When you select stored centrally, you can choose the following host 【video, or video】 host is not optional. Local storage query: 【Name】 group - the list of devices in the corresponding group information. 【Name】 channel - when choosing a host device, the channel name in the host corresponds to a channel information. 【file type】 - Select the query file types, including manual recording, timer recording, alarm recording. 【start time】 - start time of the query video, support for direct manual input and click on the drop-down box to the two setting methods. Can set the date, time minutes and seconds. 【end time】 - end time of video queries, support for direct manual input and click on the drop-down box to the two setting methods. Can set the date, time minutes and seconds. The Look - set the above query, click the Query button, you can check out the corresponding video file. Query results, as shown in Figure 6-23.
Figure 6-23 Front-end storage query:Select front-end storage -> list, click in the tree to query the host or access nodes. 【Host Name】 - Shows the host name to query 【Name】channel - Display all channels under the current name of the host.
Figure 6-24 【File Type】, 【start time, end time】 , 【check the appropriate option】 with the same functionality as local storage. Centrally stored query: Select centralized storage, video host entry into the optional state. 【Video Host】 - Displays a list of all the video hosts, select the host to select the video 【host name】 - in the tree list, select the host to query or access node 【Name】 channel - the channel under the current name of the selected host list
Figure 6-25 【File Type】 【start time】 【end time】 【search】 check the appropriate option with the same functionality as local storage. 6.4.2 Video Playback Play way: the query out of the video, select a video file double-click the file playback can be realized.
Play way: select a window and a free video file playback, click the playback control buttons, you can achieve on the video file playback. 6.4.2.1Playback Control
Figure 6-26 Playback control buttons as shown in Figure 6-26. Single screen display button, click on the video playback window to single-screen display. Four-screen display button, click on the video playback window will change to four-screen display. Nine-screen display button, click on the video playback window into nine-screen display. Start / Pause button, click on video files control the start / pause. Stop button, click on the file will stop the current video playback. Slow release button, click video files can slow playback. Quick release button, click on video files can be quick release. Single frame step button, click on video files frame by frame playback can. Snap button, click to the selected video file is playing capture. Electronic Zoom button, click on the button brings up a new playback window to achieve the amplification of video file playback. Click again to cancel the electronic zoom. Results shown in Figure 6-32.
图 6-27
Mute button, click to open / close sounds.
Volume control bar, drag the video playback to adjust the size of the sound.
Playback progress bar, drag the video file playback can be adjusted location.
6.4.2.2electric zoom in
Figure 6-28
Zoom button, click to enlarge the window to control playback electronic image to enlarge. Restore button, click to enlarge the window to control playback electronic image back to normal size. Narrow the button, click to enlarge the window to control playback electronic image smaller. Move button, when the file is enlarged, click on the zoom window to control playback electronic image upward. Down button, and when the file is enlarged, click on the player can control the electronic image to enlarge the window down.
Left button when the file is enlarged, click on the player can control the electronic image left to enlarge the window. Right button, when the file is enlarged, click on the player can control the electronic image right to enlarge the window.
6.4.2.3 The menu of right click the playback
Figure 6-29 【Full Screan】 click enable full screen playback window full screen. Results shown in Figure 6-30. Click again to close the full screen. 【Recover Display】double recovery into a single screen, the Click here to restore the original display. 【status bar】 to open / close status bar. 【Single File Cycling Play】 single file loop player checked, enables a single file loop. 【Cycling List Play】 list loop player checked, the list of documents available for query loop.
Figure 6-30
6.4.3 Download 6.4.3.1 Download Focus on front-end store and check out the video files stored, you can 【download】 right in the pop-up box, select the save location, click 【Save】 button to download video files can be realized, as shown in Figure 6-31,6-32 Fig.
Figure 6-31 Click 【Show Button】of download list in the menu bar, the down load list will be show as the following figure 6-33.
Figure 6-33 Download List 【Name】 show download video file name of the file. 【Size】 display video file size in KB.
【start the download time 】to download video files show the time. 【Download progress】 download video files show the progress. 【download status 】display download status. The download is completed / stop the download / download the three states are shown. 【Download Route】Display local storage address.
6.4.3.2 Right-button menu of download list
Figure 6-34 【 Stop Download 】 Select one download record and click this file to stop download. 【Download Again】It can download again. 【Clear Record】It can clear download record. 【Clear All】It can clear all download record.
6.5 Local Storage
Figure6-35
6.5.1 Menu List
Show button which display local storage.
Hide button which can hide local storage.
6.5.1.1Record State
Display off-line state
Display on-line state
Display timing record state
Display alarm record state
Display manual record state
6.5.1.2 Disk state
Working state
Backup state
6.6 Log Management
Figure 6-36 【Start Time】Set start time of checking log 【Close Time】Set close time of checking log 【Log Type】Check log including load, port input alarm, disconnect video and playback according to log type.
Figure 6-37 【Host Name】Check one log according to host name. 【Channel Alarm Name】Check log according to channel, port alarm input & output. 【Check】Click check button to check log according to check condition 【Cancel Current Page】Click cancel current page to cancel log record. 【Cancel All log】Click all log to cancel current check result.
【Export Log】Click export log and storage. 【Total Page X】Display total checking page. 【Page X】Select one page and check log record.
6.7 Matrix Control 6.7.1 Configuration and Description 1,Add device information in matrix: load matrix and add user and PTZ keyboard information.
Figure 6-38 Matrix device management
Figure 6-39 Add PTZ keyboard device
Figure 6-40 Set keyboard connection state
Figure 6-41 Add device address and submit 2,Add user and ID is “user’s code” of “matrix control” and if matrix didn’t has “use’s ID” but user of “matrix control” used this code, in this way it can’t load successful.
Add matrix user
6.7.2 Open Matrix Control Board Open matrix control board through
button on pan/tilt control board
Figure 6-38 1、 Select load matrix name on 【Matrix Name】, 【User Code】display default user’s code and user also can change it. 2、 【User Password】edit user’s password 3、 Click【Load】 enter to matrix control interface. 4、 Click【Load Management】enter to matrix management interface. 5、 Note:【User’s Code】Code range from 1-96 which are matrix’s user.
6.7.3 Matrix Management
Figure 6-39 【Add】 1、 【Matrix Name】edit matrix name Note:【Matrix Name】can be any character including Chinese, and the maximum length is 20 characters(Chinese is 10 characters). 2、 【Matrix IP】edit matrix IP address Note:【Matrix IP】not including 0.0.0.0 or 255.255.255.255 and illegal IP 3、 【Matrix Port】edit matrix monitoring keyboard port number. 4、 【Local Port】edit local connection matrix port number. Note:【Matrix Port】and【Local Port】port range from 1025-65535; 5、 【User’s code】edit user’s code of loading matrix. Note:【User’s code】Code range from 1-96. 6、 Click 【Add】,if new add name repeat with matrix name list, software will display “repeated matrix name, please change new name”, edit 【Matrix Name】otherwise will display “add successful” and display new name in 【Load Matrix Name】 【Modify】 1、 【Load Matrix Name】select matrix name which need modify. 2、 Modify【Matrix IP】,【Matrix Port】 3、 Click 【Modify】,software will display “if modify matrix information” and click
【 Confirm 】 will display “modify matrix successful”, otherwise will cancel modify operation. 【Cancel】 1、 【Load Matrix Name】select matrix name which need cancel 4、 Click 【Cancel】software will display “if cancel matrix information” and click 【Confirm】will display “cancel matrix successful” and matrix name in 【Load Matrix Name】is disappeared , otherwise will cancel the operation.
6.7.4 Matrix Control
Figure 6-40
6.7.4.1 Switch
Figure 6-41 【Block/Unblock】 【Camera/Monitor】 (1) 【Camera/Monitor】select camera/monitor which need block/unblock. (2) Click 【Block/Unblock】,under block state, it cannot work with pan/tilt control, focus and zoom, monitor cannot be switch. 【Call/Setup】 【Preset Postion】 (1) 【Camera】Select camera which need call/setup preset position. (2) Click【Call/Edit】, call/setup preset position of camera. 【Switch】Control (1) 【Switch Type】select video switch type (2) Click【Switch】to finish switch function. “sideway switch”,”exceed authority switch”,”synchronous switch” 【Zoom/Focus/Iris】Setup (1) 【Camera】select camera need zoom/focus/iris. (2) Click【+/-】to set camera Pan/Tilt Control (1) 【Camera】select camera need control
(2) 【
Pan/tilt control according to control board. 】
Speed of Pan/Tilt according to control bar, and greater control bar, the faster;
6.7.4.2 Arm and Disarm
Figure 6-42 6、 Set arm and disarm type in【Arm/Disarm Type】 【 Arm/Disarm Type 】 :”Single-point Arm/Disarm”,”Area Arm/Disarm” 和 ”All Arm/Disarm” 7、 According to【Arm/Disarm Type】, set the【Alarm Area ID/Alarm Point ID】; The scope of【Alarm Area ID】 is 1-16; The scope of【Alarm Point ID】 is 1-4096; 8、 Click【Arm/Disarm】 button,the arm/disarm setup will display on 【Alarm Point Information】(Figure6-43);
Figure 6-43 Set alarm items in 【Alarm Point Information】by matrix. Click right button in 【Alarm Point Information】, it can control “Single-point Arm/Disarm” and “Manually Clear Alarm”
6.7.4.3 Macro Operation Macro operation interface is as Figure 6-44
Figure 6-44 (1) Select the logical ID in 【Camera】 and lick【Camera】button to call upon the default Macro invocation, also the information will display in the Macro list. (2) Select the logical ID in 【Monitor】 and lick【Monitor】button to call upon the default Macro invocation, also the information will display in the Macro list. (3) Select the logical ID in 【Camera】 and call upon Macro logical ID of 【Monitor】, then select 【Macro ID】, and click 【Macro Invocation】 to call upon parameter Macro, also the information will display in the Macro list. (4) Select one Macro in the list(Figure 6-45), and click stop Macro by right button to stop it.
Figure 6-46
6.8 Keyboard Management Click
Figure in the right corner by right button, and select 【 Keyboard
Management】 , or find 【 Keyboard Management】 from Start men (Figure 6-47)and open the software (Figure 6-48)
Figure6-47
Figure 6-48 Keyboard management is used to add cameras, and it needs to setup IP address, name, authority and keyboard time interval. There are eight levels of authority, and 1 is the highest. When several keyboards try to control one device, the higher level keyboard will have priority. When the higher level keyboard exist and the “keyboard interval time” passed, the lower level one can control it. After setup, click “Adding Keyboard” to add keyboard list information, meanwhile, click “Delete Keyboard” to delete the keyboard information. Please “Open Surveillance Port” to control by keyboard.
7,Remote Control 7.1 Tiandy Device Remote Control Tiandy device remote control as Figure 7-1
Figure7-1
7.1.1 Common Setting Click 【Common Setting】to enter remote common setting as Figure 7-2
Figure 7-2 【Channel Number: List all the channels major code and stream settings. 【Set Video Shelter District】: Select 【Set Video Shelter District】 and hold the right
button to set the shelter district. Figure7-3
Figure7-3 【Eliminate District】: Click to eliminate the shelter district. 【Display FPS and Code Stream Information】: Select to display FPS and Code Stream information. Figure 7-4
Figure7-4 【Fore-end Snapshot】: Click to snapshot the current Figure and record. 【Overturn】Overturn the video.
Note: Only the Tiandy mini speed dome support the overturn function.
7.1.2 Video Parameter Click 【Video Parameter】 to enter remote control video parameter. Figure 7-5
Figure 7-5 【Channel Number】:List all channel major code and stream setup. 【Video Quality】: Set the video quality according to the internet situation: Best, Better, Good, Bad, Worse. 【FPS】:Set the FPS information:1,5,10,15,20,25. 【Stream Type】:Set video stream or video/audio stream. 【Priority Mode】Set frame rate priority (flute video) and quality priority(clear video). 【Code Rate】Set code rate information. The higher value is, the clearer video is. 【Resolution】Set video resolution: QCIF,HCIF,FCIF,HD1,FD1. 【Code Stream Type】Set video stream type:CBR,VBR. 【System】Set video system:PAL,NTSC. 【Video Coding】Set video coding type:H.264,Motion JPEG. 【Audio Coding】Set audio coding type:G711_A,G711_U,ADPCM_DIV4.
【Play Preference】Set video play preference: low delay, flute 【I Frame Frame Rate】Select I Frame Frame Rate value.
7.1.3 Character Overlying Click 【Character Overlying】to enter remote character overlaying setup, Figure7-6
Figure7-6 【Channel Number】List all channels and stream setup. 【Channel Name】Set overlying name and click 【Setting】 to complete. 【Overlying Type】Choose overlying information, such as date and channel name. 【Date Location】Set overlying date location. 【Channel Location】Set overlying channel location. 【Additional Character】Add description information. 【Additional Character Location】Set additional location information
7.1.4 Alarm Setting Click 【Alarm Setting】 and there are three types of alarm type: Movement Alarm, Loss Alarm and Port Alarm.
7.1.4.1 Movement Alarm Click 【Movement Alarm】 to enter alarm setting, Figure7-7
Figure7-7 【Channel Number】List all channels and stream setup. 【Capable】Choose to enable the alarm setting for the channel. 【Set Movement Alarm District】Select it and set movement district by dragging mouse, Figure7-8
Figure 7-8 【Clear up Area】It may clear up video shelter area which is setted after click.
【Video Moving Alarm Sensitivity】User may set video moving alarm sensitivity according to actual requirement, more bigger value, more higher sensitivity. 【Organization Defense Setting】User can set date and specifical time slot 【Linkage Type】User can choose type and channel number of alarm linkage.
7.1.4.2 Lose Alarm Click【Lose Alarm】Enter into lose alarm setting interface,as the Figure 7-9 is shown:
Figure 7-9 【Channel Number】List all the channel number of this host 【Enable】It show that alarm setting is use for this channel after choose. It show that alarm setting isn’t use for this channel after choose. 【Organization Defense Setting】User can set date and time slot of organization defense 【Linkage Type】User can choose alarm linkage type and channel number.
7.1.4.3 Port Alarm Click【Port Alarm】enter into port alarm setting interface as the Figure 7-10 is shown
Figure 7-10 【Input Port】User can choose alarm input port according to actual situation 【Enable】It show alarm input port is available after checked 【Model Setting】It is alarm model of input port that it is corresponding for input port. 【Output Port】User can choose alarm output port according to actual situation 【Model Setting】It is corresponding for output port, it is alarm model of output port 【Organization Defense Setting】User may set date and time slot of organization defense 【Linkage Type】User can choose type and channel number of alarm linkage
7.1.4.4 Server Click【Server】enter into server setting interface,as the Figure7-11 is shown
Figure 7-11 【Alarm Server】Fill in alarm server IP and port., Click 【Setting】after fill in. 【Serial Server】Fill in serial server IP and port. Click 【Setting】after fill in.
7.1.5 Network Parameter Click the left of main interface【Network Parameter】, Network parameter setting includes: wired setting,register center,DDNS,PPPOE and FTP.As the Figure 7-12 is shown 7-12
Figure 7-12
7.1.5.1 Wired Setting Click【Wired Setting】enter into wired setting interface, as the Figure 7-13 is shown:
Figure 7-13 【IP Address】Control Host IP 【Subnet Mask】The Subnet Mask of Control Host 【Gateway Address】The Gateway Address of Control Host 【DNS】Control Host DNS 【Physical Address】The Physical Address of Control Host. 【WEB Port】The WEB Port of Control Host. 【Auto Obtain】System will automatically obtain 【IP Address】,【Subnet Mask】, 【Gateway Address】 and 【DNS】.
7.1.5.2 Register Center Click【Register Center】,Enter into the setting interface of register center ,as the Figure 7-14 is shown
Figure 7-14 【Account】User register account number in register center. 【Password】User register account and password in register center. 【Server Name】User register server name in register center. 【IP Address 1】The IP address of register center 【Port 1】The port of register center. 【IP Address 2】The subnet mask of control host. 【Port 2】The port of control host.
7.1.5.3 DDNS Click【DDNS】enter into DDNS setting interface, as the Figure 7-15 is shown.
Figure 7-15 【Start DDNS】DDNS take effect after checked 【Server Domain】DDNS is server domain 【DNS Server】DDNS DNS Server Address. 【Port Number】DDNS Port Number. 【User Name】DDNS DDNS User Name. 【User Password】DDNS User’s Password. 【Password Confirmation】DDNS User’s password Confirmation.
7.1.5.4 PPPOE Click【PPPOE】enter into PPPOE setting interface, as the Figure 7-16 is shown
Figure 7-16 【Enabled PPPOE】PPPOE setting take effect after checked 【User Account】PPPOE Account Name 【User Password】PPPOE Account and Password 【Password Confirmation】Password Repeat Confirmation 【Use UPnP】Use UPnP agreement after checked.
7.1.5.5 FTP Click【FTP】enter into FTP setting interface,as the Figure 7-17 is shown.
Figure 7-17
【FTP Server Address】The address of FTP server. 【FTP Serve Port】The port of FTP serve. 【Route】The route of FTP serve. 【User Name】Register user name of FTP serve. 【Password】Register the password of FTP serve.
7.1.6 Front End Save Click the left of main interface 【Front end save】, front end save includes: SATA,USB,NFS,Videotape, Alarm Prerecord and Storage Strategy
7.1.6.1 SATA Click【SATA】enter into SATA setting interface, as the Figure 7-18 is shown
Figure 7-18 When front end have disc equipment, 【Loading State】will have corresponding disc identification. User may choose the special application of setting disc in 【Application】, 【Partition Number】it is the partition sum of this disc. 【Disk Space】 is the total capacity (MB)of disc. 【Surplus Space】is surplus capacity (MB) of disc.
7.1.6.2 NFS Click 【NFS】enter into NFS setting interface, as the Figure 7-19 is shown.
Figure 7-19 【IP】IP address of NFS server. 【Address Mapping】Mapping address for remote server.
7.1.6.3 Recording Policy Click recording policy to enter the setting interface as 7-20.
Figure 7-20 【Channel】List all the channel and the setting of code stream. 【Recording Status】Recording status of host machine. 【Manual Recording】User can set the manual recording policy according to the practical need. 【Date】User can take the manual setting for each day, click【Apply to everyday】 so the rules can be used everyday.
7.1.6.4 Alarm Prerecording Click【Alarm Prerecord】to enter the setting interface as 7-21.
Figure 7-21 【Channel】List all the channel and the setting of code stream of the host machine. 【Enable Alarm Prerecord】Click it, the user can set the alarm prerecord time and alarm videotape delayed.
7.1.6.5 Storage Tactics Click【Storage Tactics】to enter the setting interface as 7-22.
Figure 7-22 According to user’s practical condition to set【By Time Packaging】and 【By Size Packaging】. 【Storage Tactics】When the disk if full, user can choose【Circulate Delete】,【Stop Recording】and 【Circulate Delete(Except Alarm File)】.
7.1.7 Advanced Options Click the left side’s 【Advanced Options】which include version inFigureation, system inFigureation, user administration, file updating and log management.
7.1.7.1 Version InFigureation 【Version InFigureation】to enter the interface which include SDK version, inner core version and factory number as 7-23.
Figure 7-23
7.1.7.2 System InFigureation Click【System InFigureation】to enter the interface as 7-24
Figure 7-24 【Recover Fault】Recover the system’s default values 【Start Equipment】Restart all the remote control device.
7.1.7.3 User Management Click【User Management】to enter the interface as 7-25
Figure 7-25 【Choose User】The registered user. When 【User Name】,【Password】,【Password Confirmation】 and 【Authority】 are being set, click【Addition】to add new user. When【Choose User】【 , Old Password】【 , New Password】【 , Password Confirmation】 are being set, click 【Modify Password】to modify the password. 【Choose User】Choose the user to be deleted,click【Delete】to delete the user.
7.1.8 Cruise Setting Click the left side’s【Cruise Setting】to enter the interface as 7-26
Figure 7-26 【Channel】List all the channels of the host machine. 【Cruising Track No.】Click it to enable the function of cruising track. 【Cruising Points】All the inflection points being set in the cruising. 【Dwell Time】Set the dwell time in the cruising. After the setting,click【Call】 to start auto cruising, click【Stop】auto cruising.
7.1.9 Intelligent Analysis Intelligent analysis include: Parameter alarm info, target and alarm setting.
7.1.9.1 Parameter Alarm Info Click 【Parameter Alarm Info】 to enter the interface as 7-27
Figure 7-27 【Channel】Current alarm channel. 【Target Parameter Set】Support QCIF and FCIF. 【Display Target】Display the target. 【Display Cruising】Display target’s cruising track. 【Target Color】Display target’s color. 【Alarm Color】Display alarm’s color. 【Track Length】Display track’s length. 【Target Detect Sensitivity Set】Set the detect sensitivity.
7.1.9.2 Target Click【Target】to enter the interface as 7-28
Figure 7-28 【Channel】Current alarm channel number. 【Enable】Click it to enable all the settings. 【Ruse ID】Set 8 rules at most. 【Rule Name】Set the rule name. 【Set Event】Choose【Mix Line】and【Perimeter】. 【Alarm Type】Choose people and car. 【Alarm Color】Choose the color in the condition of not alarm. 【Minimum Time】Choose the minimum to trigger alarm. 【Minimum Length】Choose the minimum pixel to trigger alarm.
7.1.9.3 Alarm Setting Click【Alarm Setting】to enter the interface as 7-29
Figure 7-29 【Channel Number】Channel number of alarm. 【Enable Intelligent Analysis】Click it to enable all settings. 【Arming Setting】Set the alarm’s date and time slot. 【Linkage Type】 User can choose 【Link Output】 and 【PTZ Linkage】
