Transcript
ETC Quick Guide Unison Echo ® EchoAccess Configurable Devices
Overview When used in conjunction with the Unison Echo® EchoAccess Interface, the EchoAccess mobile app enables you to configure and control your Echo controls system from a mobile device. The EchoAccess Mobile App uses Bluetooth® Smart technology to control and configure Echo products over a wireless connection.
Application
Interface
Mobile Application
Select the EchoAccess Mobile App on your device to begin using EchoAccess. The app opens to the Connection Page. If you have multiple Interfaces within range, they will be listed on this initial screen. Select the Interface you want to work with. If security is enabled, you’ll be prompted to enter a password.
Note:
Use the Bluetooth enabled EchoAccess App device within 30' of the EchoAccess Interface. Walls and other solid objects positioned between the transmitter and the receiver will impact the transmission of the Bluetooth signal. Avoid obstructions when possible.
Main Menu Tap on the Main Menu item in the upper right corner of the screen to access the Main Menu. This menu gives you access to all available control and configuration options.
Devices A number of Unison Echo devices can be configured using the EchoAccess Application. The following is an overview of those devices and their configuration options. Please reference the EchoAccess Application Online Help System for additional information on configuration properties and actions.
EchoAccess Interface Use EchoAccess Interface to customize system features such as: • General - Interface Name: maximum length of seven (7) characters. • Control Features - Visibility control of: Space Level Control, Sequence Control, Lockout Control, Space Combine Control, and Preset Record Control. • Security - Settings for both control and configuration can be allowed or disallowed. • Allowed Spaces - Allow or Disallow each space to be controlled from the Interface. Spaces that are disallowed will not be shown throughout the app. The dots at the bottom of the screen indicate there are additional configurable spaces. Swipe left or right to access the configuration options for each space. Space Configuration from the Interface • Space # General - Space Name, Number of Presets, Number of Zones. Corporate Headquarters Middleton, WI, USA Tel +608 831 4116 Service: (Americas)
[email protected] London, UK Tel +44 (0)20 8896 1000 Service: (UK)
[email protected] Rome, IT Tel +39 (06) 32 111 683 Service: (UK)
[email protected] Holzkirchen, DE Tel +49 (80 24) 47 00-0 Service: (DE)
[email protected] Hong Kong Tel +852 2799 1220 Service: (Asia)
[email protected] Web: www.etcconnect.com © 2016 ETC. All Rights Reserved. Product information and specifications subject to change. 7186M1300-1.0.0 Rev A Released 2016-02 ETC intends this document to be provided in its entirety.
EchoAccess Devices
Page 1 of 6
Electronic Theatre Controls, Inc.
ETC Quick Guide EchoAccess Configurable Devices • Preset Info - Edit the name of each preset that appears within a space • Zone Info - Edit the name of each zone and set zones as Color Zones, revealing the color picker on the Zone Control Page.
Inspire Stations Note:
Changes made in EchoAccess impact the behavior of Custom mode of Inspire stations only. Preset and Zone modes remain unaffected by these settings. Preset, Custom or Zone modes are selected using the Function Selection Switch on the front of the station.
To configure the custom mode of a button-only station: Tap on the button to configure each action of a button. Depending on the type of action selected, additional menus will appear and may include Preset Number, Zone Number, Timing, etc. Use the drop down menus and keypad to enter the desired information. • Push - use the drop down menu to select the action of a pushed button. • Push and Hold - use the drop down to select the action of a button when you push and hold. • Double Tap - Use the drop down menu to select the action when you double tap on a button. • Indicator Behavior - sets the color of the indicator light when an action is "on" and when it is "off." To configure the custom only mode of a button-fader station: All button options are the same as a standard Inspire station as previously discussed. The fader has the following additional configuration options. • Push - Use the drop down menu to select the action of the fader when pushed. • Double Tap - Use the drop down menu to select the action of the fader when tapped twice. • Fader - Use the drop down menu to select the action of the fader when rotated to the left or right.
Responsive Controls Unison Echo Responsive Controls include both the Occupancy/Vacancy sensor and the Unison Echo Light Sensor.
Configuring an Occupancy/Vacancy Sensor • Occupancy Timeout - Use the drop down menu to set the length of time the sensor waits before triggering the next action. Options include 5 minutes, 15 minutes, 30 minutes, and Automatic. • PIR Led Enabled - When enabled, the sensor illuminates when occupancy is detected. • Walktest Activated - Start or stop the walk test function from this menu. Walk test enables you to physically walk through a space to confirm the functional range of a sensor. • Occupancy Sensor Event - Use the drop down menu to set the event action. Based on this action, additional menus will be provided that may include Zone Number, Value, and Timing. Set all additional values as desired using the keypad.
EchoAccess Devices
Page 2 of 6
Electronic Theatre Controls, Inc.
ETC Quick Guide EchoAccess Configurable Devices Configuring a Light Sensor Note:
Changes made in EchoAccess impact the behavior of Custom mode of Light Sensors only. Basic config mode (Custom switch set to Off) remains unaffected by these settings. The Custom mode On/Off switch is located on the rear of the device.
Light Settings • Current Measurement - gives the current lux level of the sensor. • Record Target - tap to use the current lux level as the target level. • Target Lux Value - tap to manually set a custom level. Sensitivity • Photo Timeout - set the length of time the sensor waits before triggering the next action. Options include 5 minutes, 15 minutes, 30 minutes, and 60 minutes. Photo Deadband • This setting determines how far off the Target Lux Value the current lux measurement must be (in % of the Target Value) for the sensor to take action. With the Target Lux Value as the center point, threshold values can be calculated by adding or subtracting the Deadband % Target. • Low=Target - (Target x Deadband%) / 100 • High=Target + (Target x Deadband%) / 100 Action Type Set to function as either Switch or Dim • When in Switch mode: the sensor has two events with configurable actions. When measured light exceeds the Bright threshold its action occurs, and when measured light is below the Dark threshold its action occurs. • When in Dim mode: once the measured light is found to be outside the target +/- deadband amount, the sensor will continuously trigger Dimming Raise Events and Dimming Lower Events until the target amount of light is reached or artificial lighting reaches maximums.
Switch Action • Switched Bright Event- Use the drop down menus and keypad to set the action, the preset associated with that action, and the timing of the preset fade. • Switched Dark Event - Use the drop down menus and keypad to set the action, the preset associated with that action, and the timing of the preset fade.
Dim Action • Dimming Raise Event- set Zone Raise/Lower or Space Raise/Lower. Additional menus will become available based on the action selected. Use the keypad and drop down menus to select additional settings. • Dimming Lower Event - set Zone Raise/Lower or Space Raise/Lower. Additional menus will become available based on the action selected. Use the keypad and drop down menus to select additional settings.
Zone Controllers Relay Controllers General Configuration • Aux Input Mode - Set the Aux Input Mode to either Disabled, Occupancy, or Photo • Occupancy Event - Use the drop down menus and keypad to set the desired action, the preset the action is associated with, and the timing.
EchoAccess Devices
Page 3 of 6
Electronic Theatre Controls, Inc.
ETC Quick Guide EchoAccess Configurable Devices • Dimming Bright Event - Use the drop down menus and keypad to set the desired action, the preset the action is associated with, and the timing. • Dimming Dark Event - Use the drop down menus and keypad to set the desired action, the preset the action is associated with, and the timing. Preset Configuration Swipe to the left or right to access the second page and set the timing and circuit values for each programmed preset.
0-10V Controllers Preset Configuration Use the keypad to set the default timing and circuit values for each programmed preset.
SmartSpace Controllers General Configuration • Aux Input Mode - Set the Aux Input Mode to either Disabled, Occupancy, or Photo. • Occupancy Event - Use the drop down menus and keypad to set the desired action, the preset the action is associated with, and the timing. • Bright Event - Use the drop down menus and keypad to set the desired action, the preset the action is associated with, and the timing. • Dark Event - Use the drop down menus and keypad to set the desired action, the preset the action is associated with, and the timing. Preset Configuration Swipe to the left or right to access the second page and set the default timing and circuit values for each programmed preset.
600W Phase-Adaptive Dimmer General Configuration • Dim Phase - Use the drop down menu to set the dimmer curve to either Automatic, Forward, or Reverse. • Dim Mode - Tap to set the dimmer mode to either Normal or Fluorescent. • Fluorescent Turn On Percent - Use the keypad to set the percent at which you'd like the fluorescent fixtures to turn on. Preset Configuration Swipe to the left or right to access the second page and set the default timing and circuit values for each programmed preset.
EchoAccess Devices
Page 4 of 6
Electronic Theatre Controls, Inc.
ETC Quick Guide EchoAccess Configurable Devices Room Controllers AV Input Type - Options are Momentary or Maintained. The AV input type is set at the Room Controller. This field within the app is read only. The following options change depending on the AV Input Type setting, and provide those options for the current Input Type setting only. Momentary • Momentary Control Event - This event is similar to a single button push, executing the configured action with each closure of the dry contacts. Use the drop down menus and keypad to set the Action type, Preset Number and Timing(s) of that event. Maintained • Contact Closed - This event occurs when the contact closes. • Contact Open Action - This event occurs when the contact opens. Use the drop down menus and keypad to set the Action type of that event. Swipe to the second page to set circuit values and timing for each preset.
DMX Scene Controller The DMX Scene Controller is capable of outputting a full universe of DMX 512 (512 channels) and supports the storing of 32 presets.
Note:
Changes made in EchoAccess impact the Custom config mode of the DMX Scene Controller only. Basic mode remains unaffected by these settings. Basic or Custom modes are selected using the Config Mode Switch on the front of the device.
General Configuration • Control Unpatched Addresses - When enabled, all DMX addresses in the universe will be snapshot-recorded into presets. When disabled, only DMX address that are patched to the DMX Scene Controller’s zones will be snapshot-recorded into presets. • Allow Space Actions to Affect Unpatched Addresses - When enabled, all DMX addresses in the universe will be subject to space actions such as Space Raise and Lower. When disabled, only DMX address that are patched to the DMX Scene Controller’s zones will be affected. • Allow Patch Auto Shift - When enabled, DMX addresses will auto-adjust when consecutively patched fixture profiles are modified. • DMX Output Refresh Rate - Sets the output refresh rate of the DMX Scene Controller. Use the drop down menu to set the desired rate. Swipe to page 2 to configure the DMX Scene Controller's zone patch. It's possible to patch zones individually, or use the Patch Wizard to configure multiple zones to use the same properties. Patch Wizard Configure multiple zones to use the same profile with individual addresses. • Profile - select the fixture profile for all included zones. • Zones - determine which zones should be configured together with a similar set of profiles.
EchoAccess Devices
Page 5 of 6
Electronic Theatre Controls, Inc.
ETC Quick Guide EchoAccess Configurable Devices • Start Address - Tap to set the DMX start address of the first zone. Subsequent zones will assign addresses consecutively. Patch Configuration Use the drop down menu to patch the color profile for each zone. Tap the Add Addresses button to connect additional addresses to each zone. Tap the "x" next to an address, or range of addresses to delete addresses from a zone. Preset Configuration Each available preset is shown along with an editable field that dictates how long a preset takes to play from beginning to end.
Preset Stations Note:
Changes made in EchoAccess impact the Custom mode of the Preset Station only. Basic mode remains unaffected by these settings. Basic or Custom modes are selected using DIP switch 1 on the rear of the station.
Configuring Preset Stations Configure each button individually on a Preset Station. The following options are available for each button. • Push - use the drop down menu to select the action of a pushed button. • Push and Hold - use the drop down to select the action of a button when you push and hold. • Double Tap - Use the drop down menu to select the action when you double tap on a button. • Indicator Behavior - sets the color of the indicator light when an action is "on" and when it is "off." For additional information on EchoAccess Mobile App or any of the devices that can be controlled and configured, reference the EchoAccess Application Web Help. This can be found in the EchoAccess App, or on the ETC website at www.etcconnect.com.
EchoAccess Devices
Page 6 of 6
Electronic Theatre Controls, Inc.
