Ecoview Touchscreen Installation And System

Transcript

Installation Instructions Document No. 129-568 February 28, 2014 EcoView™ Touchscreen Installation and System Start-up This document covers the installation of the EcoView™ Touchscreen and startup of the EcoView system. See the following documents for installation of other EcoView system components: • EcoView 8 DO Module Installation and Commissioning (129-565) • EcoView Thermostat Installation Instructions (129-564 or 129-566) • EcoView Multi-phase Meter Installation Instructions (129-563) Expected Installation Time 60 minutes Prerequisites • 100Base-T Ethernet connection is available. • EcoView 8 DO Module and EcoView Thermostat schedules are designed and ready to be entered into EcoView Web. • Product Description Ethernet port 80 is open or access to port 80 is available through a proxy server. • The EcoView Touchscreen is a full-color 7-inch tactile display device, master controller and Internet gateway built into a single wall-mounted unit. A single CAT5 cable supplies both power and data. An EcoView ZigBee Repeater (Digi Router) (P/N 97-003) is available in case network communication is troublesome because a ZigBee device is out-of-range. • If multiple EcoView Touchscreens are being used at the site, do the following to close all other ZigBee networks that are already installed: a. Remove the front bezel of each installed EcoView Touchscreen. Product Number 60-009 EcoView Touchscreen controller/gateway graphical user interface with ZigBee. Includes power transformer with 3-prong grounded cord, shielded CAT5 cable, and ferrite. b. Press and hold the CONFIG button for one second to display the Configuration screen. (See Figure 4.) Optional Product c. 97-003 d. Press the Advanced tab. EcoView ZigBee Repeater, plugs into 115-120V, 60 Hz 3-prong grounded outlet. Caution Notations CAUTION: Equipment damage or loss of data may occur if you do not follow the procedures as specified. Required Tools and Materials • Flat-blade screwdriver (1/8-inch blade width). • Drywall saw or appropriate tool for cutting drywall. • Drywall anchors or molly bolts. • Wire strippers. • One CAT5 cable which is long enough to run between the EcoView Touchscreen mounting location and the DSL/cable modem or router. Item Number 129-568, Rev. BA Press the DEVICE NETWORK icon. e. If the Network Status is Open, on the right side of the screen, press the Open button to toggle the network to closed. The button text changes to Closed. (See Figure 5.) f. Press OK to clear the window. Depending on the type of installation, other prerequisites may have to be completed. CAUTION: Always wear an electro-static discharge (ESD) wrist strap and discharge accumulated static before touching field panel components. Page 1 of 9 Document No. 129-568 Installation Instructions February 28, 2014 3. Clamp the ferrite on the shielded CAT5 cable, within four inches of the RJ-45 connector, and plug this end into the ETHERNET connector on the back of the EcoView Touchscreen. (See Figure 2.)  Ensure the connector clicks securely in place. NOTE: The ferrite clamp is used to reduce radiated emissions. 4. Route the modem CAT5 cable from the DSL/cable modem or router to the EcoView Touchscreen location.  Route the modem CAT5 cable above the drop ceiling or inside the wall so that it is hidden as much as possible. Figure 1: EcoView Touchscreen Dimensions. 5. Remove the front bezel of the EcoView Touchscreen by pulling out along the bottom edge. Installation NOTE: For purposes of this installation instruction, the shielded CAT5 cable provided with the EcoView Touchscreen is referred to as the shielded CAT5 cable. (Note the metal-clad RJ-45 connectors.) The CAT5 cable that runs between the Power Over Ethernet (PoE) Injector and the DSL/cable modem or router is referred to the modem CAT5 cable.  The four shrouded mounting holes are now visible. (See 1 in Figure 3.) CAUTION: Do not touch any components on the circuit board. 6. Using either molly bolts or drywall anchors, attach the EcoView Touchscreen to the wall. 7. Do not replace the EcoView Touchscreen front bezel at this time. The EcoView Touchscreen may be installed on any wall. Typically, it is located in or just outside the manager’s office. 1. Select a mounting location for the EcoView Touchscreen where it will be easily-accessible and where wire can be easily routed to the DSL/cable modem or router. 2. Using a drywall saw or another appropriate tool, cut a hole in the mounting location for routing wiring.  If the EcoView Touchscreen is to be flushmounted, cut a 7-1/4” wide × 4-1/2” high hole.  If a flush-mount is not required, cut a 3” × 3” hole. Figure 3: Home Screen on the Configuration Screen. 1 Shrouded mounting holes 2 RESET button 3 CONFIG button Figure 2: Shielded CAT5 Cable with Ferrite Connection to the Touchscreen. Page 2 of 9 Siemens Industry, Inc. Document No. 129-568 Installation Instructions February 28, 2014 Connecting Power and a Network Connection The Power Over Ethernet (PoE) Injector supplies power and an Ethernet network connection to the EcoView Touchscreen. Data Connection 1. Plug one end of the modem CAT5 cable into the PoE Injector port labeled DATA (or LAN). 2. Plug the other end of the modem CAT5 cable into the DSL/cable modem or router.  Ensure the connectors click securely in place. Power Connection 1. Plug the free end of the shielded CAT5 cable (from the EcoView Touchscreen) into the PoE Injector port labeled DATA + PWR (or LAN + DC). The EcoView Touchscreen installation is now complete. Continue with the procedures Starting up the EcoView Touchscreen.  Ensure the connector clicks securely in place. 2. Connect the supplied 3-prong AC cord to the PoE Injector. 3. Plug the 3-prong AC cord into a power socket.  The EcoView Touchscreen powers up.  After approximately one minute, the main screen displays. Figure 4: Connections to the Power Over Ethernet (PoE) Injector. Figure 5: Device Settings/Advanced Tab—Resetting the Zigbee Network. 1 Home button 2 Reset button 3 PAN ID and Channel 4 Zigbee network status 5 Unassigned nodes 1. Siemens Industry, Inc. Page 3 of 9 Document No. 129-568 Installation Instructions February 28, 2014 Starting up the EcoView Touchscreen 6. Press the Home button. 7. Press the General tab. NOTE: 8. Press the Set button. (See 1 in Figure 7.) You must complete all the start-up procedures to ensure proper operation of the EcoView system. Selecting the EcoView Preferred ZigBee Communication Channel Before any new devices are powered on or joined to the EcoView Touchscreen, reset the ZigBee network so that any Wifi channels in use at the installation site may be avoided. 1. Press the EcoView Touchscreen CONFIG button for one second and then release it to display the Configuration screen. 2. Press the DEVICE NETWORK tab. 3. Press the Advanced tab. 4. Press the Reset Network button in the Network list. (See 2 in Figure 5.) 5. Press OK to continue with the reset. ⇨ The ZigBee network resets and automatically selects a preferred communications channel. 6. Press OK to close the message box. 7. Verify that both the PAN ID and the Channel values have changed. (See 3 in Figure 5.) Calibrating the Screen and Setting the System Time 1. Press the SYSTEM icon. 2. Press the Visual tab. 3. Press the Screen Calibration button. (See 1 in Figure 6.) Figure 6: System Settings/Visual Tab, Caibrating the Screen. 4. Press the center of the cross at all locations until the screen is blank. 5. Press anywhere on the screen to return to the SYSTEM tab. Page 4 of 9 Figure 7: System Settings/General Tab, Setting the System Time. 9. Set the time and date, and then press Apply. 10. In the upper left corner of the screen, press the Home button. (See 1 in Figure 5.) Entering the Network Settings NOTE: Most DSL routers are configured for Dynamic Host Configuration Protocol (DHCP), which means that no router configuration is necessary. Skip this section if DHCP is being used. 1. Press the CLOUD icon. 2. Press the Advanced tab. 3. On the left side of the screen, complete the IP Address, Subnet Mask, and Gateway fields. (See 1 in Figure 8.) Figure 8: Cloud Settings/Advanced Tab, Entering the IP Address, Subnet Mask, and Gateway Information. 4. On the right side of the screen, press the Apply button. (See 2 in Figure 8.) Siemens Industry, Inc. Document No. 129-568 Installation Instructions February 28, 2014 Registration 1. Press the CLOUD icon. 2. Press the Activation Code box. (See 1 in Figure 9.) Figure 10: Cloud Settings/Configure Tab. Figure 9: Activation Tab.  A keypad screen displays. 3. Type your activation code, and then press the Accept button.  A message stating that the EcoView Touchscreen has been successfully activated displays.  If an error message displays, see the Troubleshooting section. NOTE: Join devices one-at-a-time. This minimizes any confusion caused by having several MAC addresses displayed on the screen at one time. 3. Select a device from the Unassigned Nodes list to start the Device Configuration Wizard. 4. Select the appropriate device driver from the list (see 1 in Figure 11), and then press the Next button. (See 2 in Figure 11.) NOTE: If only one driver is available for the selected device, skip this step. 4. In the upper left corner of the screen, press the Home button. Assigning Devices to the Touchscreen NOTE: Skip this section if the EcoView 8 DO Module, EcoView Power Meter, or EcoView Thermostat will be assigned to the EcoView Touchscreen during installation of that device. 1. Press the DEVICE SETTINGS icon. (See Figure 3.) 2. Press the Configure tab.  Unassigned node IDs display in the Unassigned Nodes list. (See 5 in Figure 5.)  Assigned EcoView 8 DO Modules, EcoView Power Meters, and EcoView Thermostats display in the Configured Device list. (See Figure 3.)  Unassigned EcoView 8 DO Modules, EcoView Power Meters, and EcoView Thermostats display in the Unconfigured Device list. (See 1 in Figure 10.) Siemens Industry, Inc. Figure 11: Device Wizard/Device Driver Selection. 5. Select parameters from the list (see 1 in Figure 12) to edit the value, and then press the Next button (see 2 in Figure 12).If needed, press the Back button (see 3 in Figure 12) to return to the previous screen. NOTE: If there are no editable parameters for the selected device driver, skip Step 5. Page 5 of 9 Document No. 129-568 Installation Instructions February 28, 2014 Testing the EcoView 8 DO Module 1. From the EcoView Touchscreen main menu, press the ON/OFF icon.  The Load Control screen displays. 2. Toggle each switch OFF and back ON. 3. Ensure that the EcoView 8 DO Module responds correctly. NOTE: The switches must be toggled at least once before the EcoView 8 DO Module will be in sync. Figure 12: Device Wizard/Parameters. 6. Select the desired Zigbee MAC address from the list (see 1 in Figure 13), and then press the Finish button. Testing the EcoView Thermostat 1. At each EcoView Thermostat, verify that the heating and cooling calls function appropriately. 2. Perform a delta T on each unit. 3. Demonstrate the system functionality to the manager or building owner. Resetting Other ZigBee Networks that are Closed (Only for sites with multiple EcoView Touchscreens)  Complete this procedure at each EcoView Touchscreen where the ZigBee network is closed. 1. Remove the front bezel of each installed EcoView Touchscreen. 2. Press and hold the CONFIG button for one second to display the Configuration screen. 3. Press the DEVICE NETWORK icon. Press the Accept button. 4. Press the Advanced tab.  The EcoView 8 DO Module, EcoView Power Meter, or EcoView Thermostat is assigned to the EcoView Touchscreen and locked into the wireless network. 5. On the right side of the screen, press the Reset Network button. (See 2 in Figure 5.) Figure 13 Device Wizard/Zigbee MAC Assignment. 7. 8. Repeat Steps 2 through 4 for each device that needs to be assigned. 9. In the upper-left corner of the screen, press the Home button to return to the main screen. 10. Press the Exit button to save the configuration. (See 4 in Figure 3.)  The EcoView Touchscreen main menu displays. Installing an EcoView ZigBee Repeater (Optional) If a ZigBee device is out-of-range, an EcoView ZigBee Repeater can be added to improve signal strength. 1. Find a suitable location that is the midpoint between the EcoView Touchscreen and the device with poor signal strength. 2. Plug the EcoView ZigBee Repeater into the nearest available power outlet. (The higher off the ground the better.) 3. Press the recessed reset button on the side of the EcoView ZigBee Repeater four times to join it to the EcoView Touchscreen network. 11. Replace the front bezel of the EcoView Touchscreen. NOTE: To ensure correct bezel positioning, see the label on the inside of the bezel, which has an arrow and the word TOP. The EcoView Touchscreen start-up is now complete. Page 6 of 9 Siemens Industry, Inc. Document No. 129-568 Installation Instructions February 28, 2014 4. Press the recessed reset button once to ensure the Node ID information was sent to the EcoView Touchscreen. 5. Using the provided plate screw, attach the router to the outlet to discourage people from disconnecting the router. Locking the EcoView ZigBee Repeater into the EcoView Touchscreen Network 1. Select the router from the Unassigned ZigBee Device list. (See 5 in Figure 5.) 2. In the dialog that displays, press the Add button.  Upon being successfully added into the panel ZigBee network, the Device Type changes from Router to Router (Configured). 3. Repeat the procedure, Testing the EcoView ZigBee Repeater. NOTE: The RSSI value should be less than 75. 4. In the lower right corner of the screen, press the Exit button to save the configuration. Checking for Upgrades Figure 14: ZigBee Repeater. Use this procedure to check for available firmware and service upgrades. Testing the EcoView ZigBee Repeater 1. Press the System icon.  Complete this procedure for each EcoView ZigBee Repeater. 1. Press and hold the EcoView Touchscreen CONFIG button for one second to display the Configuration screen. 2. Press the DEVICE NETWORK icon. 3. Press the Advanced tab.  The EcoView ZigBee Repeater MAC address should be displayed in the Unassigned Nodes list as a router. 4. Press the Test tab. 5. Select the EcoView ZigBee Repeater MAC address in the drop-down list, and then press the Test button.  The test results display in the new window.  The Passed and Failed sections indicate how many pings passed and how many failed.  The RSSI section displays the Received Signal Strength. 6. If the test fails, repeat the test.  If a device doesn’t pass after several tests, the device is not connected. Repeat the procedure Installing a ZigBee Repeater. 2. Press the Updates tab.  The system checks with the cloud to find any available upgrades and displays them in the list. 3. Do one of the following: – To install the recommended package: Press the Install button. – To install a specific package: Select the package from the list, and then press the Install button. Configuring Basic Network Settings Use this procedure to configure basic network settings, and to load a previously downloaded firmware or service package, through the bootloader. 1. Remove the front bezel of the EcoView Touchscreen by pulling out along the bottom edge. 2. Press and hold the CONFIG button (see 3 in Figure 3) and then press the Reset button (see 2 in Figure 3). Continue to hold the CONFIG button until the bootloader screen displays. Network Configuration 1. Press the Network tab. 2. If using DHCP, select the DHCP option. 3. If using a static IP address, complete the IP Address, Subnet Mask, and Gateway fields. Siemens Industry, Inc. Page 7 of 9 Document No. 129-568 Installation Instructions February 28, 2014 Loading a Package FCC and IC Interference Requirements 1. Press the Apps tab. This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.” 2. Select the desired package from the list, and then press the Load button. 3. In the dialog that displays, press the Yes button. Troubleshooting Removing Device(s) Installed to an EcoView Touchscreen in Error (Only for Sites with Multiple Touchscreens) Use this procedure if an EcoView 8 DO Module, EcoView Power Meter, or EcoView Thermostat has joined the wrong EcoView Touchscreen network. 1. Remove the front bezel of the EcoView Touchscreen by pulling out along the bottom edge. 2. Press and hold the CONFIG button for one second to display the Configuration screen. 3. Press the DEVICE SETTINGS icon. 4. Press the Advanced tab. 5. On the right side of the screen, press the Open button to toggle the network to closed.  The button text changes to Closed. 6. Press the Configure tab and deselect Hide Configured Devices. (See 2 in Figure 10.) 7. In the list, select the device. 8. In the Device Configuration Wizard, press the Decommission button. « Ce dispositif est conforme à la partie 15 des règles de FCC et aux normes permis-exemptes du Canada RSS d'industrie. L'opération est sujette aux deux conditions suivantes (1) que ce dispositif peut ne pas causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence, y compris l'interférence qui peut causer le fonctionnement peu désiré du dispositif. » Per RSS-Gen Issue 3 (December 2010 Section 7.1.3) FCC Note This device complies with Part 15 of the FCC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC and IC Radiation Exposure Statement for Mobile Devices “This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be re-located or operating in conjunction with any other antenna or transmitter.” (For compliance with FCC Code of Federal Regulations Title 47 Part 2.1093) 9. Press the Accept button. 10. Return to the device and install it on the correct EcoView Touchscreen network. Resetting the EcoView ZigBee Repeater to Manufacturer’s Defaults Use this procedure if an EcoView ZigBee Repeater does not join the network after several attempts. 1. Press and hold the recessed reset button on the side of the EcoView ZigBee Repeater for about 20 seconds. 2. Repeat the procedure, Installing an EcoView ZigBee Repeater. Page 8 of 9 Siemens Industry, Inc. Document No. 129-568 Installation Instructions December 21, 2011 FCC Code of Federal Regulations Title 47 Part 15.105 Information to the user: This equipment has been tested and found to comply with the limits for a Class B, digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turnings the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. For Industry Canada User “This Class A digital apparatus complies with Canadian ICES-003 Issue 4 (February 2004).” « Cet appareillage numérique de la classe A est conforme ICES-003 à l'issue canadienne 4 (le février 2004). » Antenna “Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.” « Aux termes des règlements du Canada d'industrie, cet émetteur radioélectrique peut seulement fonctionner utilisant une antenne d'un type et (ou moins) d'un gain maximum approuvés pour l'émetteur par Industry Canada. Pour ramener des interférences radio potentielles à d'autres utilisateurs, on devrait ainsi choisir le type d'antenne et son gain que l'équivalent a isotropically rayonné la puissance (e.i.r.p.) n'est pas plus que celui nécessaire pour la communication réussie. Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced. EcoView is a trademark of Siemens Industry, Inc. Other product or company names mentioned herein may be the trademarks of their respective owners. © 2014 Siemens Industry, Inc. Siemens Industry, Inc. Building Technologies Division Retail and Commercial Systems 1000 Deerfield Parkway Buffalo Grove, IL 60089-4513 USA +1 847-215-1000 For EcoView system support, please call 1 + 877-306-9400 Your feedback is important to us. If you have comments about this document, please send them to [email protected] Document No. 129-568 Printed in the USA Page 9 of 9