Ecs G24 All-in-one Pc Chassis Integration With The Gigabyte Ga-q87tn Desktop Board

Transcript

ECS G24 ALL-IN-ONE PC CHASSIS INTEGRATION WITH THE GIGABYTE GA-Q87TN DESKTOP BOARD 1. Disconnecting the Speaker Unit 2. Removing the Back Panel 3. Placing the HDD in the Mounting Bracket Disconnect the speakers by pushing down on clips on either side of the bottom of the chassis and remove the speaker section. To remove the back panel, insert a screwdriver into the corner flange and lever gently to release catch. This needs to be done on either side of the chassis. Place the HDD into the mounting bracket and connect all SATA connectors, as pictured. 4. Securing the HDD to the Mounting Bracket 5. Installing the Optional HDD 6. Removing the HDD Carrier Secure the HDD to the mounting bracket by fastening the retention screws on the underside of the bracket. To install the optional HDD in the ODD position, insert the HDD into the carrier by sliding it into the bracket. To remove the HDD carrier, simply pull back the retention mechanism. 10. Connecting the SATA Connectors 11. Connecting the Audio Cable Connector 12. Replacing the Speaker Unit Connect the HDD and ODD SATA connectors. Clip the audio cable connector to the chassis before connecting the speaker unit to the chassis. Clip the speaker unit to the chassis by lifting it into place. Ensure that the back chassis cover has been replaced prior to clipping on the speaker unit. LCD INTEGRATION NOTES 1. Inserting the LVDS Connector 2. Checking Jumper Settings 3. Configuring the BIOS LCD - 5V 2 1 2 3 Navigate to Chipset 1 Select Enable for LVDS Control Function FPD - 19V 1 When inserting the LVDS Connector, confirm correct alignment. Once in, never remove the cable by “pulling on the wires”, as this could permanently damage the cable. 2 Select M215HGE-L10/M240Q002 for Panel Type 3 Confirm that this jumper settings for the Backlight Inverter and Front Panel voltage are correct for the inverter and the board being integrated. Ensure LVDS Cable is Connected Navigate to Chipset Select Enable for LVDS Control Function Select M215HGE-L10/M240Q002 for Panel Type 2. Placing the Thermal Tab 3. Inserting the Desktop Board Once the thermal retention mechanism is in place, secure the thermal pad as above. When installing the desktop board, it may help to locate the power connection on the desktop board with the IO shield first and then “swivel” the board in. Check that the ports on the desktop board connect with the IO shield contacts. 5. Single USB Connection 6. Wireless Connection Where a “single” USB connection is connected to a dual USB header, confirm that the “red” cable is aligned to the pins closest to PIN 1 (white marking at the base). It is possible to connect two single USB connections to a dual port USB header in this manner. For Wireless-N & Wireless-AC maximum bandwidth potential, ensure that both wireless antennae are connected to the wireless adapter. GENERAL INTEGRATION NOTES 1. Placing the Thermal Retention Mechanism Check that the thermal retention mechanism is in place before installing the desktop board. 4. SATA and DATA The SATA power cable provides power for the HDD and ODD. GIGABYTE GA-Q87TN DESKTOP BOARD OVERVIEW 1. LVDS 2. LCD Panel SW 3. Front Panel 4. CPU Fan 5. SATA Power 6. DDR3 SP DIMM 7. SATA III Ports 8. Single USB Header 9. USB 3 Connect 10. Half Length Mini PCI-e Slot 2 33 3 15. HDMI 16. COM1 17. USB 3 18. LPT 27 19. Speaker Out 31 20. Mic In 21. Speaker 22. FP Audio 5 23. DMIC 6 24. CLR CMOS 25. Full Length Mini PCI-e / mSATA 7 26. PCI-e 4X 7 27. 2 x Single USB Headers 7 26 8 9 7 13. 2x GbE LAN Ports 14. Display Port 28 30 32 4 11. Internal ATX 19V Connector 12. 19V DC In 29 1 25 10 16 18 24 21 13 13 14 15 17 17 19 20 29. FPD 30. BL_SW 31. WFLED 22 11 12 23 28. Dual USB 2 Header 32. LCD PWR 33. FPD PWR