Edh-ps-4030 Spec

Transcript

Filling A Need A complete guide to Edhard equipment PRODUCT INDEX Page 3 Page 6 Filler Units: F-Series FHP-Series Power Base: PV-Series Page 3 Page 7 Filler Units: FS-Series RP-Series Power Base: PT-Series Filler Units: FT-Series Page 4 Page 8 Power Base: P-Series Cake Decorator: CDR-Series Turntable: T-Series Page 5 Page 9 Power Base: PS-Series Accessories 2 Page 10-11 Specifications FILLER UNITS: F, FHP, FS, RP SERIES F-Series These filler units* are molded in clear, FDA approved polycarbonate. They are available with 6-quart (5.5-liter) or 18-quart (17-liter) capacity hoppers and feature single or double outlets. F-Series filler units can perform a wide range of metering functions from filling pastries to depositing one product onto another. A large variety of specialized spouts adapt the filler units to fill donuts, eclairs, croissants and other pastries. They dispense smooth batters, layer toppings, deposit butter and cream cheese onto bagels and rolls and meter other semi-liquid products, quickly and efficiently. For metering non-food products, we offer the F-Series filler units molded in Valox®**. The F-Series filler units can be used with P, PS and PV-Series power bases. FHP-Series filler units are gear-type pumps constructed in polycarbonate and are available in single outlet configuration with 6-quart (5.5-liter) or 18-quart (17-liter) capacity hoppers. The FHP-Series was designed as an alternative to the FS-Series by offering the same high-pressure capability at a lower cost. Like the FS-Series and RP-Series, the metered output from these units is not affected by the product level in the hopper. This series is capable of metering a wide range of viscous products, with a high degree of accuracy. The FHP-Series is compatible with P-Series, PS-Series and PV-Series power bases. FHP-Series FS-Series filler units feature USDA approved 304 type stainless steel construction with 10-quart (9.5-liter), 18-quart (17-liter) or 36-quart (32-liter) capacity hoppers. Additionally, 6-quart (5.5-liter) or 18-quart (17-liter) polycarbonate hoppers are available with these gear-type, single outlet pumps. These filler units accept most accessories. The 18-quart (17-liter) capacity stainless steel hoppers (with 30˚ neck) can be used with our adjustable electrostatic heaters, which keep a product at a given temperature while it is being dispensed. The FS-Series must be used with the more powerful PS-Series and PV-Series power bases. FS-Series 3 RP-Series RP-Series filler units feature the same stainless steel construction and hopper capacities as the FS-Series. However, their distinguishing characteristic is the three-lobe impellers. This pump can dispense viscous products, containing particles up to the size of a 3/8” (10 mm) cube without crushing. The RP-Series is also used to dispense grainy products as well as delicate products, which cannot be “overworked” while being pumped. These units are only available in a single outlet configuration and accept most accessories. The RP-Series must be used with the PS-Series and PV-Series power bases. *Filler unit is a complete unit (pump & hopper). Filler Units lift on and off power bases - they are interchangeable. Different filler units can be used with one power base, assuming horsepower requirements are met. **For non-food products use Valox® or stainless steel filler units. POWER BASE: P-SERIES P-Series The P-Series power base is available with 1/37HP or 1/15HP. Both type bases are reliable and durable, engineered for years of maintenance-free service. The exterior is designed so that merely a damp cloth is needed to keep it clean. Both bases have the same features that make them useful in a wide variety of applications. They include - Normal Cycling, Reverse, Automatic Cycling and Continuous Dispensing, which can be selected at the keypad. The F-Series filler units are suited for P-Series power bases. Normal Cycle: The amount of product to be dispensed can be preset at the digital keypad. As the trip arm is pressed, the unit will cycle once to dispense the preset amount, then stop and reverse. Reverse: The reverse is needed to pull product back after a dispensing cycle is completed, which prevents dripping. Reverse can be adjusted to meet specific requirements. Automatic Cycle: This function eliminates the need to continually press the trip arm during multi-cycle applications. In this function, the amount dispensed and waiting time can be set to suit a specific need. Automatic cycling eliminates operator fatigue and improves productivity in repetitive, long-running jobs. Continuous Dispensing: 4 When selecting this function, the operator or a remote-triggering device, such as a photoelectric switch, determines the start and stop of the pumping action. This function is useful when a continuous stream of product is deposited on a conveyor or manually via a hose attachment. All power bases can be triggered manually by a trip arm (standard on P, PS, PV or PT power bases), our foot switch or hose assembly (accessories), or your own photoelectric switch. POWER BASE: PS-SERIES PS-Series The PS-Series power base offers the same reliability and maintenance-free design as the P-Series with the same controls and operating functions. The added benefit of the PS-Series power base is its 1/8 hp motor. The availability of higher power broadens the range of products that it can dispense. It is best suited for use with FS-Series and RP-Series filler units. • Get the job done... Edhard equipment fills a need in the marketplace. The bakery, food service, cosmetic and packaging industries use our metering systems to save time and material. A partial list of food products which can be injected, deposited, layered, metered and topped by using our metering system: Batters, butter, cheesecake, cottage cheese, cream cheese, creams, custard, fruit fillings, honey, icing, jelly, ketchup, molasses, mustard, oils, peanut butter, preserves, pudding, purees, ricotta cheese, salad dressings, salsa, syrups, tomato paste, tomato sauce, whipped cream, yogurt and many other products. Photos feature food service applications: filling pastry shells with creamed spinach, metering salsa and cheese for nachos, filling pasta shells with ricotta and filling potato skins. Non-food* product applications: Cosmetic creams, finger paints, gels, glycerin, hand creams, lotions, industrial lubricants, ointments, petroleum jelly, toothpaste and other products. *For non-food products use Valox® or stainless steel filler units. 5 POWER BASE: PV-SERIES PV-Series The PV-Series power base gives the operator complete control over the speed at which a product is dispensed (which is not possible with the single speed power bases), the amount to be dispensed, the ability to adjust reversing of the pump after each cycle, automatic cycling and continuous dispensing. The ability to control all of these functions broadens the range of product applications. Speed Control: This is essential in order to deliver a product onto a conveyor by precisely matching the speed of the belt. It also enables a product to be dispensed through a spout or a hand-held hose assembly at a speed comfortable to the operator. Control of dispensing speed is necessary when metering a product into a container where splashing must be controlled. Speed control is also essential in preventing delicate pastry shells from bursting during injection. These are only a few examples that illustrate the importance of this capability. Normal Cycle: Each time the trigger is activated in a normal cycling mode, the unit will dispense a preset amount of product, reverse and then stop. Reverse: The reversing motion of the pump after each cycle is necessary to ensure precise product cutoff. This motion prevents dripping in higher viscosity products. However, in applications involving products with lower viscosity, dripless-valves are offered to aid in cleaner product cut off. Automatic Cycle: 6 Automatic cycling is a function that relieves the operator from repeatedly pressing the trigger in order to cycle the unit. The amount dispensed and waiting time are fully adjustable, as they are in all of our power bases. Continuous Dispensing: The continuous dispensing mode is used to pump a product for an indefinite period of time. Combined with speed control, it provides extreme flexibility in a virtually endless variety of applications. All of the above functions are fully adjustable from the control pad and provide the user with uniformity, control and flexibility in any metering application. POWER BASE: PT-SERIES PT-Series The PT-Series transfer system meters products directly from a mixing bowl or other container, thus eliminating frequent and time consuming hopper refills. Some of its applications are: filling cups, trays, pans, bottles and other containers as well as depositing muffin, cupcake and pound cake batter, pie fillings, topping Danish pasteries, tarts etc. The PT-Series power base can be used in two distinct modes: 1. As a metering transfer system, where the product can be pumped directly from a large vat or mixing bowl and dispensed in metered quantities through a variety of accessories and custom spout configurations. 2. As a gravity fed system, where the product is placed in a hopper and dispensed through a selection of accessories and custom spout configurations. The PT-Series is a completely portable system and consists of two major components - a power base and a pump/filler unit. When pumping from a large vat, the power base and pump assembly may be placed on a table or our specially designed cart (part no. FT-8010). The suction tube, fitted with a check-valve on one end, extends directly down to the bottom of the vat. The system may be placed alongside a conveyor with a discharge spout configuration extending over the moving belt. The spout configuration may be directed in a 180-degree radius. The PT-Series may be placed over a conveyor, if used as a hopper-type system instead of a transfer system. 7 The power base has the same functions as our PV-Series, namely-speed control, reversing, normal cycling, automatic cycling and continuous dispensing. There are two basic pumps available for the PT-Series. The FT-Series is a gear-type pump (similar to FS-Series) and is used to meter smooth products. The FTR-Series is a lobe-type pump (similar to RP-Series) designed to meter grainy material as well as products containing particles (nuts, fruit, berries etc.), suspended in a semi-liquid. Photos feature: PT-Series power base, FT-Series pump assembly, FTR-Series filler unit and PT-Series complete with cart. CAKE DECORATOR: CDR-SERIES CDR-Series The CDR-Series offers the ability to decorate and border cakes as well as sculpt roses. This unit will also dispense cream puff and eclair batter, cookie dough and assorted icings. With the CDR-Series, the operator has full control over the amount, shape and speed at which a product is dispensed. The CDR-Series replaces the age-old pastry bag with an 18-quart (17liter) capacity hopper, which represents approximately 36 to 40 fillings of a pastry bag. Using a pastry bag, the operator risks hand and wrist injury (carpal tunnel syndrome). With the CDR-Series, product pressure (speed) is adjusted by merely turning the dial. The hand pressure required to squeeze the trigger is very low and, more importantly, remains constant regardless of the dial setting. This dispenser consists of four main assemblies - power base, filler unit, gun/hose assembly and balancer assembly. The power base is selfcontained and requires no maintenance. The filler unit consists of a hopper and pump. The filler units are available in polycarbonate or 304 type stainless steel construction. Both units are easy to clean. They disassemble without the use of tools. A pressure disc is included with each unit, which, when placed on top of the product in the hopper, prevents cavitation in the hopper and assures uninterrupted flow of product through the system. 8 The decorating gun is ergonomically shaped and places the operator’s hand in a comfortable decorating position. A comfortable hand position is necessary to avoid operator fatigue. The counterweighted balancer assembly suspends the gun and hose assembly in the most comfortable motion range for ease of decorating. The decorating gun is offered in three configurations: as a right or left hand pistol type or as a straight type. In addition, the hose assembly accepts a de-aerator device, which enables the operator to create delicate decorations without air bubbles. Tools are not required to disassemble the gun and hose assembly for cleaning. The CDR-Series comes complete with adaptors, which accept all standard decorating tips. The T-Series turntable is designed to speed the decorating process, leaving both hands free to decorate. This turntable features: • 12” diameter removable table • Clockwise and counterclockwise rotation • Variable speed control • 60 lb. load capacity • Housing constructed of rugged polycarbonate T-Series ACCESSORIES Standard and Eclair Spouts Layering and Croissant Spouts Plain and Cannoli Spouts Balancer Assy. Hose Assy. and Foot Switch 45° & 90° Spouts Heaters for Stainless Steel Filler Units 9 Cupcake Spouts For complete list of accessories, please refer to equipment & accessories brochure. Custom Spouts Built to Your Specifications MK MKH MKHX MKHX MKHX MKS MKSX MKSX MKSX MKT MKTX MKTH MKV MKVX MKVX MKVX CD CDX CDX CDX CT P P P P P PS PS PS PS PT PT PT PV PV PV PV CDR CDR CDR CDR T 120 220 200 100 120 220 200 100 120 240 200/240 100/120 220 200 100 120 220 200 100 120 120 Volts 60 50 50/60 50/60 60 50 50/60 50/60 60 60 50/60 50/60 50 50/60 50/60 60 50 50/60 50/60 60 60 Hz 0.025 / 19 0.25 / 186.5 0.25 / 186.5 0.25 / 186.5 0.25 / 186.5 0.25 / 186.5 0.25 / 186.5 0.25 / 186.5 0.25 / 186.5 0.536 / 400 0.268 / 200 0.268 / 200 0.125 / 93 0.125 / 93 0.125 / 93 0.125 / 93 0.059 / 44 0.059 / 44 0.059 / 44 0.067 / 50 0.027 / 20 Power Hp/W Edhard Metering System = Power Base + Filler Unit. Please consider HP requirements for future applications. 14 / 6.4 18 / 8 18 / 8 18 / 8 18 / 8 18 / 8 18 / 8 18 / 8 18 / 8 31.5 / 14.3 29.3 / 13.3 29.3 / 13.3 18 / 8 18 / 8 18 / 8 18 / 8 12 / 5.5 12 / 5.5 12 / 5.5 12 / 5.5 12 / 5.5 Weight lb/kg 16.5 / 419 15.4 / 391 15.4 / 391 15.4 / 391 15.4 / 391 15.4 / 391 15.4 / 391 15.4 / 391 15.4 / 391 13.13 / 333 13.13 / 333 13.13 / 333 15.4 / 391 15.4 / 391 15.4 / 391 15.4 / 391 15.4 / 391 15.4 / 391 15.4 / 391 15.4 / 391 15.4 / 391 Width inch/mm 12 / 305 9 / 229 9 / 229 9 / 229 9 / 229 9 / 229 9 / 229 9 / 229 9 / 229 15.75 / 400 15.75 / 400 15.75 / 400 9 / 229 9 / 229 9 / 229 9 / 229 9 / 229 9 / 229 9 / 229 9 / 229 9 / 229 Depth inch/mm SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. MADE IN USA AND SOLD THROUGHOUT THE WORLD. 6.7 / 170 9.5 / 241 9.5 / 241 9.5 / 241 9.5 / 241 9.5 / 241 9.5 / 241 9.5 / 241 9.5 / 241 8.75 / 222 8.75 / 222 8.75 / 222 9.5 / 241 9.5 / 241 9.5 / 241 9.5 / 241 6.75 / 172 6.75 / 172 6.75 / 172 6.75 / 172 6.75 / 172 Height inch/mm Equipment Specifications *CD is a complete system: Power Base + Filler Unit + Hose & Gun Assy. + Balancer Assy. CD filler units are available in stainless steel or polycarbonate. Model Series Power Bases 10 Used With Power Bases P/ PS / PV P/ PS / PV P/ PS / PV P/ PS / PV PS / PV PS / PV PS / PV PS / PV PS / PV PT PT PT PT PS / PV PS / PV PS / PV PS / PV PS / PV Series F F FHP FHP FS FS FS FS FS FT FT FTR FTR RP RP RP RP RP Filler Units Polycarb. Polycarb. Polycarb. Polycarb. St. Steel St. Steel St. Steel St. Steel None St. Steel None Polycarb. Polycarb. St. Steel St. Steel St. Steel Polycarb. Polycarb. St. Steel St. Steel St. Steel St. Steel St. Steel St. Steel St. Steel St. Steel St. Steel St. Steel St. Steel St. Steel St. Steel St. Steel Lobe Lobe Lobe Lobe Lobe Lobe Lobe Gear Gear Gear Gear Gear Gear Gear Gear Gear Gear Gear 36 / 32 18 / 17 10 / 9.5 18 / 17 6 / 5.5 Transfer Type 18 / 17 Transfer Type 18 / 17 36 / 32 18 / 17 6 / 5.5 18 / 17 10 / 9.5 18 / 17 6 / 5.5 6 / 5.5 18 / 17 Capacity quart/liter 10.25 / 260 9 / 229 9 / 229 10.25 / 260 Diameter inch/mm 9 / 229 - 12.5 / 318 - 12.5 / 318 14 / 356 10 / 254 23.4 / 10.6 18 / 8.1 14 / 6.3 14 / 356 10 / 254 10 / 254 12.7 / 5.54 10.25 / 260 10 / 4.5 11.5 / 5.2 21.7 / 9.8 10.8 / 4.9 21 / 9.5 22.7 / 10.3 17 / 7.7 9/4 9 / 229 11.55 / 5.26 10.25 / 260 13 / 5.9 10 / 254 5.1 / 2.32 3.75 / 1.7 3.75 / 1.7 5.1 / 2.32 Weight lb/kg 22 / 559 23.3 / 592 15.6 / 396 21.5 / 546 15.3 / 338 6.0 / 152 25.5 / 648 6.0 / 152 25.5 / 648 22 / 559 23 / 584 15 / 381 21.1 / 536 15.3 / 338 19.75 / 502 15 / 381 15 / 381 19.75 / 502 Height inch/mm SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. MADE IN USA AND SOLD THROUGHOUT THE WORLD. S S S S S S S S S S S S S S S S S&D S&D Outlet Single/Dbl Edhard Corp., 279 Blau Road, Hackettstown, NJ 07840 USA Tel: 908 850-8444 • [in USA 888 EDHARD1] • Fax: 908 850-8445 email: [email protected] • www.edhard.com Polycarb. Polycarb. Polycarb. Polycarb. Pump Type EQUIPMENT SPECIFICATIONS Construction Pump Hopper 11 A-2200 05.03 Edhard Corp., 279 Blau Road, Hackettstown, NJ 07840 USA Tel: 908 850-8444 • [in USA 888 EDHARD1] • Fax: 908 850-8445 email: [email protected] • www.edhard.com Equipment and Accessory Guide WELCOME We welcome all newcomers to the world of Edhard! Due to the versatility of our equipment and systems we have arranged the following concepts to help guide you in making a decision or, at least, give you an understanding of the type of information your Edhard representative will need in order to determine the best equipment to satisfy your requirements. Before looking through this brochure please take some time to think about the following conditions and answer the questions. Dosing action Å Inject - 1 or 2 at a time Å Deposit - 1, 2 or 4 at a time Å Fill - Jars, Bottles, Containers, etc. Å Transfer Product charactersitics Å Is it smooth or does it have inclusions/particles? Å If it has particles - what are their size and ratio to overall product? Å What is the product’s viscosity or thickness? Å Is it whipped and airy? Å At what temperature is it to be dispensed - chilled, room temp, hot? Å Does the product flow? Does a mound of it collapse and level or does it hold a shape? Dosage amount Å Fractions of an ounce to pounds Å Grams to Kilograms Pan or container configuration and size Å 2-4 at a time - center to center spacing Typical production run volume Å Quantity of finished products produced daily. Å Multiple mixing bowls? How many? Å Expected equipment usage time daily / weekly. The above information coupled with an understanding of the terminology on the following pages will help you navigate this product listing and help your Edhard representative best understand your needs. EDHARD TERMINOLOGY POWER BASE Cream-colored unit that houses electronics and motor. Engages Pump or Filler Unit and makes them dispense product. Keypad controls the amount of product dispensed, cycle-type and, in some models, the speed of output. Available in 3 -Series PT -Series styles of table-top unit (PP-, PS- & PV PV-Series -Series) as well as the stand-alone unit (PT PT-Series -Series). FILLER UNIT A Lexan Hopper and Pump Housing combination coupled with a Pump Cover Assembly and Gear-Type Impellers. The Pump Housing and Hopper are fused together and -Series are not meant to be taken apart. Filler Units refer to the F- and FHP FHP-Series -Series. Accept a wide variety of Spouts and Attachments. F-Series available in Single and Double -Series available in Single Outlet only. Used for loose to medium Outlet while FHP FHP-Series viscosity proucts. PUMP A stainless steel, Single Outlet unit that houses either Gear-Type or Lobe-Type Impellers and accepts a wide variety of Lexan and stainless steel Hoppers or a FT -Series only). Can dispense a wide range of viscosities. Used Suction Tube (FT FT-- & FTR FTR-Series PS-Series solely on higher output Power Bases (PSPS-, PV PV-- and PT PT-Series -Series). HOPPER Funnel constructed of either Lexan or stainless steel, which threads or clamps onto a stainless steel Pump. Available in 6(5.5), 10(9.5), 18(17) and 36Qt.(34) capacities. DOUBLE OUTLET Refers to the amount of exit holes on a Filler Unit. Double Outlet Filler Units accept only 7/16” (11.1) Dia. Spouts. These units are used primarily for injecting product into a baked good (think donut or eclair filling). SINGLE OUTLET Refers to the amount of exit holes on a Filler Unit or Pump. Single Outlet Filler Units and Pumps accept only 7/8” (22.2) Dia. Spouts. These units are primarily used for depositing or layering product into containers (pans, bags, tubes etc.) or onto other products (cakes, muffins, pie crusts, bagels etc.). Far more versatile in application than the Double Outlet. SPOUT Any output attachment that enables you to inject, deposit, layer or otherwise dispense product from a Filler Unit or Pump. GEAR-TYPE Refers to the type of Impeller with 6 or more teeth. Used for smooth products of varying viscosities. Standard in the F- & FHP FHP-Series FT-Series -Series Filler Units and FS- & FT -Series Pumps. Available materials include: Polypropylene, UHMW, Nylon, PEEK & Stainless LOBE-TYPE Refers to the type of Impeller with 2 to 3 rounded lobes as opposed to traditional gear teeth. Used for smooth products as well as products with suspended particles. The maximum size of particles that can be passed without crushing is approximately 3/8” RP -Series FTR -Sr eies (9.6mm) Dia. (RP RP-Series -Series) and up to 1/2” (12.7mm) Dia. (FTR FTR-Sr -Sreies eies). Effective with medium -Series Pumps. Available materials to higher viscosities. Standard in the RP RP-- and FTR FTR-Series include: Viton, Stainless Steel & PEEK. 1 KEY 2 P-, PS- & PV -Series PV-Series F F P PUMP: Sits on the Power Base and is available in Stainless Steel. Accepts one 7/8”Ø (22.2mm) S spout. FS-Series uses 6-tooth Gear-type Impellers -Series uses Lobe-type Impellers for wider for smooth products. RP RP-Series range of products including those with particles up to 3/8”Ø (9.6mm). Both accept removeable Hoppers H in either Lexan or Stainless Steel. HOPPER: Attaches to Pump P . Available in 6Qt. (5L) and 18Qt. (17L) Lexan or 10Qt. (9L), 18Qt. (17L) and 36Qt. (34L) Stainless Steel. H P J D S T T C FILLER UNIT UNIT:: Sits on the Power Base and is available in Lexan. Accepts either one 7/8”Ø (22.2mm) S or two 7/16”Ø (11.1mm) D spouts. F-Series used -Series used for a wider range for lighter, less viscous products. FHP FHP-Series including more viscous and even semi-liquid products. HOPPER A CCESSOR ACCESSOR CCESSORYY: Pressure Disc keeps stiff products from cavitating. Heating Jackets help maintain temperature in Stainless Steel Hoppers. SPOUT SPOUT:: Fits Filler Units and Pumps and available as either Double Output : 7/16”Ø (11.1mm) neck or Single Output : 7/8”Ø (22.2mm) neck. THREADED AD APT ADAPT APTOR: OR: Orifices and Adaptors available in two thread sizes - 3/4” (19mm) and 7/8” (22.2mm). CUPC AKE SPOUT CUPCAKE SPOUT:: WER B A SE A CCESSOR A PO POWER BA ACCESSOR CCESSORYY: Stainless Steel Cupcake Spout with 4 down-spouts and various center-to-center spacings. Available in two thread sizes - 3/4” (19mm) and 7/8” (22.2mm). Various accessories that fit any tabletop Power Base. KEY PT -Series PT-Series Sits on the Power Base and is available in Stainless Steel. Accepts -Series uses Gear-type Impellers FT-Series Adaptors A with sanitary flanges. FT -Series uses two Lobe-type Impellers for wider for smooth products. FTR FTR-Series range of products including those with particles up to1/2”Ø (12.7mm). Both types can accept a removeable Stainless Steel Hopper H (for viscous products) or a Suction Tube S (for less viscous and even semi-liquid products). P PUMP: S SUCTION TUBE: H HOPPER: Attaches to Hopper-type Pump P and used for more viscous products. Available in 18Qt. (17L) and 36Qt. (34L) Stainless Steel. A AD APT OR: ADAPT APTOR: Mates various types of Spouts, Elbows or Hoses S E H to any FT- or FTR-Series Pump P . S E CCESSOR ACCESSOR CCESSORYY : H OUTPUT A Attaches to Suction-type Pump P and allows product to be dosed from any size mixing bowl or drum. Available in 1-1/4”Ø (w/ check valve for loose, runny products) or 2”Ø (w/out check valve for thicker products). Various Spouts, Elbows and Hose Assemblies to finish off the depositing system. CDR -Series CDR-Series P PUMP: G DECORA TING GUN: DECORATING H HOSE A SSEMBL ASSEMBL SSEMBLYY : Sits on Power Base and is available in Gear-type and Lobe-type versions. Accepts Stainless Steel and Lexan Hoppers H in 18Qt. (17L) or 36Qt. (34L) capacities. Comes standard with De-aerator and Bleeder Tube. Accepts CDR-type Hose Assembly. Available in Pistol-type or Straight-type depending on user’s preference. Pistol-type available in righthanded and lefthanded versions. Both types will acept most sizes and types of decorating tips through the use of our specially designed Adaptors. Made to fit CDR-type Pumps P . 3 4 Equipment and Accessory Guide Tabletop PPower ower Bases What fits me? F P-40 10: -401 A 120VAC · 60/50Hz · 1/37Hp (20.2W) motor Power Base · Model MK What fits me? F 120VAC · 60/50Hz · 1/15Hp (49.7W) motor 120VAC · 60/50Hz · 1/15Hp (49.7W) motor w/ 240RPM output 220VAC · 50/60Hz · 1/17Hp (43.9W) motor - Specify power cord plug type: Australian, Euro, Italian, UK P-40 12: -401 P-40 12-HS -401 2-HS: P-4020 -4020: F A Power Base · Model MKH What fits me? F PS-4028 PS-4028: PS-4030 PS-4030: 120VAC · 60/50Hz · 1/8Hp (93.2W) motor 220VAC · 50/60Hz · 1/8Hp (93.2W) motor - Specify power cord plug type: Australian, Euro, Italian, UK F P A Power Base · Model MKS What fits me? F PV -4000 PV-4000 -4000: PV -400 1: PV-400 -4001 F P 120VAC · 50/60Hz · 1/4Hp (186.4W) motor 220VAC · 50/60Hz · 1/4Hp (186.4W) motor - Specify power cord plug type: Australian, Euro, Italian, UK Power Base · Variable Speed · Model MKV Pumps and Filler Units F F P H What fits me? F-5000 -5000: F-500 1: -5001 F-500 1 N/S -5001 N/S: F-5005 -5005: F-5005 N/S N/S: 6 Qt. (5.5L) capacity w/ 2 x F-3076 spouts 6 Qt. (5.5L) capacity w/ 2 x F-3011 spouts 6 Qt. (5.5L) capacity w/ no spouts 18 Qt. (17L) capacity w/ 2 x F-3011 spouts 18 Qt. (17L) capacity w/ no spouts D Filler Unit · Lexan · Double Outlet OPTION F F-36 16: -361 Higher strength replacement cover for Lexan DoubleOutlet Filler Units Pump Cover · Teflon-coated Aluminum · Double Outlet What fits me? S F-5003 -5003: F-5007 -5007: OPTION F 6 Qt. (5.5L) capacity 18 Qt. (17L) capacity Filler Unit · Lexan · Single Outlet F-36 15: -361 Higher strength replacement cover for Lexan SingleOutlet Filler Units Pump Cover · Teflon-coated Aluminum · Single Outlet What fits me? FHP -5025 FHP-5025 -5025: Gear-Type18 Qt. (17L) capacity FHP -5026 FHP-5026 -5026: Gear-Type6 Qt. (5.5L) capacity FHP -503 1: Gear-Type18 Qt. (17L) capacity w/ Pressure Disc FHP-503 -5031 F Filler Unit · Lexan · Single Outlet - High Pressure S P A 5 Equipment and Accessory Guide What fits me? H FS-3 153 FS-31 53: FS-34 14: FS-341 P S Gear-Type Stainless Impellers Gear-Type Nylon Impellers Pump · Stainless Steel · Single Outlet What fits me? RP -3 160 RP-3 -31 60: RP -3527 RP-3527 -3527: RP -35 14: RP-35 -351 P Lobe-Type Viton 3-Lobe Impellers Lobe-Type PEEK 3-Lobe Impellers Lobe-Type Stainless 3-Lobe Impellers (High Heat) H S Pump · Stainless Steel · Single Outlet What fits me? H RP -352 1: RP-352 -3521 P A Lobe-Type Viton 3-Lobe Impellers w/ Sanitary Outlet Pump · Stainless Steel · Single Outlet What fits me? H RP -3529 RP-3529 -3529: P S Gear-Type PEEK Impellers - For Liquids Pump · Stainless Steel · Single Outlet What fits me? P FS-3 155 FS-31 55: FS-3 150 FS-31 50: H 6 Qt. (5.5L) capacity 18 Qt. (17L) capacity Hopper · Lexan · for use on FS- and RP-Series Pumps What fits me? J FS-2342 FS-2342: FS-23 13 : FS-231 FS-244 7: FS-2447 FS-27 48 FS-2748 48: 10 Qt. (9.5L) capacity 18 Qt. (17L) capacity w/ 30° neck 18 Qt. (17L) capacity w/ 45° neck 36 Qt. (34L) capacity H Hopper · Stainless Steel · for use on FS- and RP-Series Pumps P 6 Equipment and Accessory Guide Accessories and Spouts P-3026 -3026: NO TE NOTE TE: Footswitch for remote operation of all Power Bases For Footswiches to fit older model Power Bases please contact us for the proper connector type. P-3634 -3634: Used to raise any table-top Power Base over the work surface. PS-3328 PS-3328: Used to counterbalance a Hose Assy. on any table-top Power Base A Footswitch A Bridge A Balancer Assy. FHP -3368 FHP-3368 -3368: FS-3202 FS-3202: FS-330 1: FS-3301 P Lexan for use with 18 Qt. (17L) FHP-Series Filler Unit or FS-3150 Stainless Steel for use with 18 Qt. (17L) S.S. Hopper w/ 45° neck Stainless Steel for use with 36 Qt. (34L) Hopper Pressure Disc FS-3269 FS-3269: 0: FS-3270 FS-327 FS-327 1: FS-3271 FS-327 2: FS-3272 J A P J D S T T C 120VAC 120VAC 240VAC 240VAC · · · · Lower section for use on 18 Qt. (17L) S.S. Hopper w/ 30° neck Upper section for use on 18 Qt. (17L) S.S. Hopper Lower section for use on 18 Qt. (17L) S.S. Hopper w/ 30° neck Upper section for use on 18 Qt. (17L) S.S. Hopper Heating Jacket · Variable temperature What fits me? D FS-3 148 FS-31 48: CUS CUSTTOM : S Spout · 7/8” Threaded Tip Hose Assy. · 7/8”Threaded Tip - 36”(.914M) long for use on F-, FS- and RP-Series Pumps Hose Assy. · 7/8”Threaded Tip - Specify Length T Equipment and Accessory Guide F-30 11: -301 Donut · 7/16”Ø x 3-1/2”L (11.1mm x 89mm) D Spout · Double Outlet · Standard Tip D Spout · Double Outlet · Standard Tip D Spout · Double Outlet · Standard Tip D Spout · Double Outlet · Standard Tip D Spout · Double Outlet · Standard Tip D Spout · Double Outlet · 30° Tip D Spout · Double Outlet · 30° Tip D Spout · Double Outlet · 30° Tip D Spout · Double Outlet · 30° Tip F-30 12: -301 F-30 13: -301 F-3065 -3065: F-3064 -3064: F-30 14: -301 F-307 6: -3076 F-3066 -3066: F-308 1: -3081 Eclair-Slit · 7/16”Ø x 5”L (11.1mm x 127mm) Eclair · 7/16”Ø x 5”L (11.1mm x 127mm) Long John-Slit · 5/16”Ø x 4-3/8”L (7.9mm x 111.1mm) Long John · 5/16”Ø x 4-3/8”L (7.9mm x 111.1mm) Blueberry · 7/16”Ø x 3-1/4”L (11.1mm x 82.5mm) Munchkin · 9/32”Ø x 2-1/4”L (7.1mm x 57.1mm) Frenchie · 3/16”Ø x 1-5/8”L (4.8mm x 41.3mm) Berliner · 1/4”Ø x 1-5/8”L (6.4mm x 41.3mm) 7 8 Equipment and Accessory Guide F-3094 -3094: S Spout · Standard Tip S Spout · Standard Tip S Spout · Standard Tip S Spout · Standard Tip S Spout · Standard Tip S Spout · 30° Tip S Spout · 30° Tip S Spout · 30° Tip S Spout · 90° Tip S Spout · 90° Tip F-3092 -3092: F-309 1: -3091 F-3096 -3096: F-3095 -3095: F-3090 -3090: F-3097 -3097: F-3339 -3339: F-3067 -3067: F-3055 -3055: Donut · 7/16”Ø x 3-1/2”L (11.1mm x 89mm) Eclair-Slit · 7/16”Ø x 5”L (11.1mm x 127mm) Eclair · 7/16”Ø x 5”L (11.1mm x 127mm) Long John-Slit · 5/16”Ø x 4-3/8”L (7.9mm x 111.1mm) Long John · 5/16”Ø x 4-3/8”L (7.9mm x 111.1mm) Blueberry · 7/16”Ø x 3-1/4”L (11.1mm x 82.5mm) Munchkin · 9/32”Ø x 2-1/4”L (7.1mm x 57.1mm) Frenchie · 3/16”Ø x 1-5/8”L (4.8mm x 41.3mm) Plain · 7/8”Ø x 7”L (22.2mm x 177.8mm) Cannoli · 9/16”Ø x 3”L (14.3mm x 76.2mm) 9 Equipment and Accessory Guide F-3043 -3043: S Spout · 90° Tip S Spout · Multi Tip S Spout · Multi Tip F-3042 -3042: F-3 101: -31 45° · 7/8”Ø x 4-3/4”L (22.2mm x 120.6mm) Croissant · 3/16”Ø x 1”L - 4 places (4.8mm x 25.4mm) Triple · 3/16”Ø x 1”L - 3 places (4.8mm x 25.4mm) What fits me? FS-3305 FS-3305: S D Double Spout Manifold · for use on FS- and RP-Series Pumps with any Double Outlet Spout Manifold What fits me? T F-304 1: -3041 F-3 103 03: -31 F-307 2: -3072 S Cupcake · 3/4”Ø x 3-1/4”Spacing (19mm x 82.5mm) Cupcake · 3/4”Ø x 3-1/2”Spacing (19mm x 89mm) Cupcake · 3/4”Ø x 4”Spacing (19mm x 101.6mm) Spout · 3/4” Threaded Tip What fits me? F-3 141: -31 F-339 1: -3391 CUS CUSTTOM : S T Universal Extension · 7/8”Ø x 6-1/4”L (22.2mm x 158.7mm) Universal Extension · 7/8”Ø x 12-1/4”L (22.2mm x 311.1mm) Universal Extension · 7/8”Ø x Specify Length Spout · 7/8” Threaded Tip What fits me? S FS-3335 FS-3335: CUS CUSTTOM : S Hose Assy. · 7/8”Threaded Tip - 36”(.914M) long w/ F-3141 Extension wand for use on F-, FS- & RP-Series Pumps Hose Assy. · 7/8”Threaded Tip - Specify Length Spout · w/ Stainless Extension and 7/8” Threaded Tip T 10 Equipment and Accessory Guide What fits me? FS-327 7: FS-3277 FS-3393 FS-3393: FS-3394 FS-3394: CUS CUSTTOM : S 7/8”Ø 7/8”Ø 7/8”Ø 7/8”Ø Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake · · · · · · · · · · · · 3/4”Ø x 2-1/4”Spacing (19mm x 57.15mm) 3/4”Ø x 2-3/8”Spacing (19mm x 60.33mm) 3/4”Ø x 2-1/2”Spacing (19mm x 63.5mm) 3/4”Ø x 2-3/4”Spacing (19mm x 68.85mm) 3/4”Ø x 3-1/4”Spacing (19mm x 82.55mm) 3/4”Ø x 3-1/2”Spacing (19mm x 88.9mm) 3/4”Ø x 3-5/8”Spacing (19mm x 92.07mm) 3/4”Ø x 4”Spacing (19mm x 101.6mm) 3/4”Ø x 4-1/8”Spacing (19mm x 104.78mm) 3/4”Ø x 4-1/4”Spacing (19mm x 107.95mm) 3/4”Ø x 4-1/2”Spacing (19mm x 114.3mm) Specify Spacing Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake Cupcake · · · · · · · · · · · · · · · 7/8”Ø x 1-1/2”Spacing (22.2mm x 38.1mm) 7/8”Ø x 2”Spacing (22.2mm x 50.8mm) 7/8”Ø x 2-1/4”Spacing (22.2mm x 57.15mm) 7/8”Ø x 2-3/8”Spacing (22.2mm x 60.33mm) 7/8”Ø x 2-1/2”Spacing (22.2mm x 63.5mm) 7/8”Ø x 2-3/4”Spacing (22.2mm x 69.85mm) 7/8”Ø x 3”Spacing (22.2mm x 76.2mm) 7/8”Ø x 3-1/4”Spacing (22.2mm x 82.55mm) 7/8”Ø x 3-1/2”Spacing (22.2mm x 88.9mm) 7/8”Ø x 3-5/8”Spacing (22.2mm x 92.08mm) 7/8”Ø x 4”Spacing (22.2mm x 101.6mm) 7/8”Ø x 4-1/8”Spacing (22.2mm x 104.78mm) 7/8”Ø x 4-1/4”Spacing (22.2mm x 107.95mm) 7/8”Ø x 4-1/2”Spacing (22.2mm x 114.3mm) Specify Spacing x x x x 4-3/4”L (22.2mm x 120.6mm) 8”L (22.2mm x 203.2mm) 10.5”L (22.2mm x 266.7mm) Specify Length C What fits me? T Spout · 3/4” Threaded Tip F-354 7: -3547 -3532: F-3532 F-3533 -3533: F-359 1: -3591 F-3534 -3534: F-3535 -3535: F-3560 -3560: F-3557 -3557: F-3494 -3494: F-3525 -3525: F-3559 -3559: F-356 1: -3561 F-3558 -3558: F-3550 -3550: CUS CUSTTOM : C · · · · Spout · Extension F-34 72: -347 F-3590 -3590: F-34 73 : -347 F-3389 -3389: F-3405 -3405: F-3556 -3556: F-34 74: -347 F-3406 -3406: F-3562 -3562: F-3390 -3390: F-34 75: -347 CUS CUSTTOM : C Cupcake Cupcake Cupcake Cupcake Spout · 7/8” Threaded Tip F-32 12: -321 T Spout · Accessory T Spout · Accessory F-32 13: -321 Bread Roll · 3-3/8”Ø (85.7mm) w/ 7/8”Threaded Inlet Bagel · 3-3/8”Ø (85.7mm) w/ 7/8”Threaded Inlet What fits me? T 11 Equipment and Accessory Guide What fits me? A F-3 147: -31 T Dripless · 7/8” (22.2mm) Threaded Inlet Valve What fits me? A F-3 187 -31 87: T A T Dripless - Extended · 7/8” (22.2mm) Threaded Inlet Valve F-207 68 -20768 68: Dripless - Bottle Filling · Used on F-3187 Dripless Valve Extended to aid in filling bottles. F-2327 -2327: FS-2397 FS-2397: CUS CUSTTOM : Decorating Tip · .56”Ø (14.2mm) Decorating Tip · .38”Ø (9.7mm) Decorating Tip · Specify Diameter F-20 145 -201 45: F-2887 -2887: FS-27 60 FS-2760 60: FS-27 39 FS-2739 39: FS-27 40 FS-2740 40: CUS CUSTTOM : Round · .22”Ø (5.6mm) Round · .38”Ø (9.7mm) Round · .47”Ø (12mm) Round · .56”Ø (14.2mm) Rectangular · .19 x .38” (4.8mm x 9.7mm) Either Shape · Specify Siziing F-207 61: -2076 Bottle Filling · Used to aid in the filling of small-neck bottles. Adaptor Orifice T Orifice T Orifice What fits me? D T T F-3267 -3267: Spout · 7/8”(22.2mm) Thread - 7/16”Ø (11.1mm) accepts any Double Outlet Spout CD-3258 CD-3258: CD-3259 CD-3259: CD-3260 CD-3260: CD-3266 CD-3266: FS-3 188 FS-31 88: Decorator Tip Decorator Tip Decorator Tip Decorator Tip Decorator Tip Adaptor Adaptor · · · · · #0 - #3 #4 - #6 #7 - #9 Euro Small 12 Equipment and Accessory Guide F-3580 -3580: F-357 8: -3578 F-32 11: -321 F-3537 -3537: F-3538 -3538: F-354 1: -3541 F-3540 -3540: F-3496 -3496: F-34 78: -347 F-34 79: -347 F-3588 -3588: F-3589 -3589: CUS CUSTTOM : T · · · · · · · · · · · · · 7/8”Ø 7/8”Ø 7/8”Ø 7/8”Ø 7/8”Ø 7/8”Ø 7/8”Ø 7/8”Ø 7/8”Ø 7/8”Ø 7/8”Ø 7/8”Ø 7/8”Ø x x x x x x x x x x x x x 1-3/16”L (22.2mm x 30.18mm) 1-3/4”L (22.2mm x 44.45mm) 2”L (22.2mm x 50.8mm) 2-1/2”L (22.2mm x 63.5mm) 2-3/4”L (22.2mm x 69.85mm) 3”L (22.2mm x 76.2mm) 3-1/4”L (22.2mm x 82.55mm) 3-1/2”L (22.2mm x 88.9mm) 4”L (22.2mm x 101.6mm) 4-1/2”L (22.2mm x 114.3mm) 5”L (22.2mm x 127mm) 5-1/2”L (22.2mm x 139.7mm) Specify Spacing What fits me? T Spout · Accessory · Threaded Tip F-286 1: -2861 F-24 19: -241 F-2497 -2497: F-2585 -2585: F-24 18 -241 F-259 1: -2591 F-2696 -2696: F-2592 -2592: F-2695 -2695: F-2 144 44: -21 F-20959 -20959: F-2267 -2267: F-20842 -20842: F-20843 -20843: CUS CUSTTOM : T Double Double Double Double Double Double Double Double Double Double Double Double Double Layering Layering Layering Layering Layering Layering Layering Layering Layering Layering Layering Layering Layering Layering Layering · · · · · · · · · · · · · · · 1.19”L x .14”W (30mm x 3.6mm) 1.6”L x .08”W (40.6mm x 2mm) 1.6”L x .16”W (40.6mm x 4mm) 1.97”L x .10”W (50mm x 2.54mm) 2.36”L x .12”W (60mm x 3mm) 2.76”L x .12”W (70mm x 3mm) 2.76”L x .14”W (70mm x 3.6mm) 3.15”L x .10”W (80mm x 2.54mm) 3.15”L x .14”W (80mm x 3.6mm) 3.5”L x .19”W (89mm x 4.8mm) 3.5”L x .25”W (89mm x 6.4mm) 4”L x .28”W (101.6mm x 7.1mm) 4.33”L x .078”W (110mm x 2mm) 4.33”L x .393”W (110mm x 10mm) Specify Length x Width Spout · Accessory What fits me? S FS-3392 FS-3392: T 7/8” Thread to 7/8” Ø · Used to mate Single Outlet Spouts to a 7/8” threaded tip (Ex. F-3141) Adaptor What fits me? F-357 7: -3577 F-3602 -3602: F-3539 -3539: F-3 140 -31 40: CUS CUSTTOM : Double Double Double Double Double T Spout · Accessory · Threaded Tip T Valve T Valve · · · · · 3/4”Ø 3/4”Ø 3/4”Ø 3/4”Ø 3/4”Ø x x x x x 1-3/4”L (19mm x 44.45mm) 3”L (19mm x 76.2mm) 3-1/4”L (19mm x 82.55mm) 4-1/2”L (19mm x 114.3mm) Specify Spacing F-3 142 -31 42: Dripless · 3/4” (19mm) Threaded Inlet F-32 14 : -321 Dripless - Extended · 3/4” (19mm) Threaded Inlet T 13 PT-SERIES The Edhard PT-Series is a stand-alone system that can be used as a dosing pump and also as a transfer pump. Its reversible motor means that this system can be used with a suction tube (for looser products) as well as a gravity-fed hopper (just like our table-top units). The system is comprised of four major components 1 2 3 4 Power Base Pump Cart Suction TTube/Hopper ube/Hopper 1 2 Various Accessories are available to finish off the system - Batter Spouts, Elbows, Extensions, etc. Remember, if you don’t see what you had in 3 mind chances are good that we can manufacture something to meet your specifications. Please call or e-mail with any questions. 279 Blau Road · Hackettstown, NJ 07840 · USA 908.850.8444 · 888.edhard.1 · Fax: 908.850.8445 [email protected] 4 14 Equipment and Accessory Guide What fits me? P PT -4035 PT-4035 -4035: PT -4036 PT-4036 -4036: PT -4037 PT-4037 -4037: 200W motor 200W motor 400W motor 120VAC 220VAC 220VAC Model MKT Model MKT Model MKT Power Base · Variable Speed · Transfer Type PT -80 10: PT-80 -801 Stainless Steel · for use with PT-Series Power Bases PT -338 1: PT-338 -3381 Used to counterbalance a Hose Asembly- attaches to column of PT-8010 Cart Balancer Assembly What fits me? A FT -3342 FT-3342 -3342: FT -3465 FT-3465 -3465: P S Gear-Type Stainless and Nylon Impellers Gear-Type PEEK Impellers Pump · Suction · Stainless Steel What fits me? A FTR -3343 FTR-3343 -3343: P FT -337 5: FT-337 -3375 FT -3430 FT-3430 -3430: S Lobe-Type Viton 3-Lobe Impellers Pump · Suction · Stainless Steel Suction Tube 1-1/4”Ø w/ ball check valve 2”Ø w/out ball check valve S 15 Equipment and Accessory Guide What fits me? FT -3366 FT-3366 -3366: FT -3466 FT-3466 -3466: FT -34 70: FT-34 -347 FT -357 3: FT-357 -3573 P Gear-Type Stainless and Nylon Impellers Gear-Type Stainless Impellers Gear-Type PEEK Impellers · for Low-Viscosity products Gear-Type PEEK Impellers · Single Outlet Housing A H Pump · Hopper Feed · Stainless Steel What fits me? A FTR -337 1: FTR-337 -3371 P H Lobe-Type Viton 3-Lobe Impellers Pump · Hopper Feed · Stainless Steel What fits me? A FTR -35 16: FTR-35 -351 P H Lobe-Type Viton 3-Lobe Impellers · Single Outlet Housing Pump · Hopper Feed · Stainless Steel What fits me? FT -20064 FT-20064 -20064: FT -20065 FT-20065 -20065: FT -20 131: FT-20 -201 H 18 Qt. (17L) capacity w/ 45° neck 18 Qt. (17L) capacity w/ 30° neck 36 Qt. (34L) capacity J P Hopper · Stainless Steel · for use on FT- and FTR-Series Pumps What fits me? S FT -3520 FT-3520 -3520: A A Manifold · Double · 4” (101.6mm) spacing - sanitary connections Adaptor What fits me? FT -3399 FT-3399 -3399: A S Sanitary Fitting to 7/8” Ø (22.2mm) · used to mate Single Outlet Spouts to FT- or FTR-Series Pumps Adaptor What fits me? FT -20 176: FT-20 -201 A H Hose to Sanitary Fitting · used to mate Hose Assy. to FT- or FTR-Series Pumps Adaptor What fits me? S FT -3586 FT-3586 -3586: A Adaptor Connector · used to mate FT-Series Adaptors, Elbows, Batter & Cupcake spouts to FT- or FTR-Series Pumps E 16 Equipment and Accessory Guide What fits me? S FT -337 7: FT-337 -3377 CUS CUSTTOM : A E Universal Extension · 1-1/8”Ø x 18-1/2”L (28.6mm x 470mm) Universal Extension · 1-1/8”Ø x Specify Length Adaptor What fits me? T FT -337 9: FT-337 -3379 E Universal Extension to 7/8” Thread · 1-1/8”Ø - 7/8”Thread (28.6mm - 22.2mm) Elbow · Threaded Tip What fits me? C FT -3386 FT-3386 -3386: E Universal Extension to Cupcake Spout · 1-1/8”Ø - 7/8”Ø (28.6mm - 22.2mm) Elbow · for use w/ F-Series Stainless Cupcake Spouts What fits me? S FT -337 8: FT-337 -3378 E S S S Universal Extension to Cupcake Spout · 1-1/8”Ø - 1-1/8”Ø (28.6mm - 28.6mm) Elbow · for use w/ FT-Series Stainless Cupcake Spouts FT -202 17: FT-202 -2021 Batter FT -3395 FT-3395 -3395: Double Batter FT -337 6: FT-337 -3376 CUS CUSTTOM : Dripless Cupcake · 3-1/4” (82.55) spacing Dripless Cupcake · Specify spacing Spout Spout Spout 17 Equipment and Accessory Guide FT -3563 FT-3563 -3563: -357 0: FT-357 -3570 FT FT -3569 FT-3569 -3569: FT -3568 FT-3568 -3568: FT -3567 FT-3567 -3567: FT -3566 FT-3566 -3566: FT -3565 FT-3565 -3565: FT -357 1: FT-357 -3571 FT -3564 FT-3564 -3564: CUS CUSTTOM : S Cupcake · 3/4”Ø x 3-1/4”Spacing (11.1mm x 82.55mm) Cupcake · 7/8”Ø x 2-3/4”Spacing (22.2mm x 69.85mm) Cupcake · 7/8”Ø x 3-1/4”Spacing (22.2mm x 82.55mm) Cupcake · 7/8”Ø x 3-3/8”Spacing (22.2mm x 85.73mm) Cupcake · 7/8”Ø x 3-5/8”Spacing (22.2mm x 92.08mm) Cupcake · 7/8”Ø x 4”Spacing (22.2mm x 101.6mm) Cupcake · 7/8”Ø x 4-1/8”Spacing (22.2mm x 104.78mm) Cupcake · 7/8”Ø x 4-1/4”Spacing (22.2mm x 107.95mm) Cupcake · 7/8”Ø x 4-3/8”Spacing (22.2mm x 111.13mm) Cupcake · Specify Spacing What fits me? T T Spout · 3/4” or 7/8” Threaded Tip What fits me? D FT -3402 FT-3402 -3402: CUS CUSTTOM : H T Hose Assy. · 7/8”Threaded Tip - 36”(.914M) long Hose Assy. · 7/8”Threaded Tip - Specify Length Spout What fits me? S FT -3548 FT-3548 -3548: CUS CUSTTOM : H T Hose Assy. · 7/8”Threaded Tip - 36”(.914M) long w/ F-3141 Extension wand for use on FT- & FTR-Series Pumps Hose Assy. · 7/8”Threaded Tip - Specify Length Spout What fits me? T FT -36 17: FT-36 -361 CUS CUSTTOM : S Spout · 7/8” Threaded Tip CUS CUSTTOM : A E S Bundt · 4x7/8”Ø on a 3-1/2”Ø (4x22.2mm x 88.9mm) Bundt · 4x7/8”Ø x Specify Diameter Custom Spouts/Extensions/Orifices · Specify product, application, size, etc. 18 CDR-SERIES The Edhard CDR-Series is a table-top system that can be used to ice and decorate cakes, create buttercream ornaments, and dispense various petitshue and spritz cookie batters. Its lack of a dosing function differs this series from the rest of our systems - the product will dispense as long as the trigger is pulled giving the operator artistic freedom when looks are more important than portion control. The system is comprised of five major components 5 1 2 3 4 5 Power Base Pump Balancer ating Gun Hose/Decorating Hose/Decor essur e Disc Hopper/Pr Hopper/Pressur essure A couple of gun styles and orientations are available as are Adaptors to accept most sizes 3 of decorating tips. 4 Please call or e-mail with any questions. 2 279 Blau Road · Hackettstown, NJ 07840 · USA 908.850.8444 · 888.edhard.1 · Fax: 908.850.8445 [email protected] 1 19 Equipment and Accessory Guide What fits me? F CD-4050 CD-4050: CD-4053 CD-4053: 120VAC · 60/50Hz · 1/4Hp (186.4W) motor 220VAC · 50/60Hz · 1/4Hp (186.4W) motor Power Base · Model CD What fits me? H CDR -3449 CDR-3449 -3449: P H Gear-Type Stainless Steel Impellers Pump · Stainless Steel · Single Outlet What fits me? H CDR -3400 CDR-3400 -3400: P H Lobe-Type Viton 3-Lobe Impellers Pump · Stainless Steel · Single Outlet What fits me? P FS-3 150 FS-31 50: FS-244 7: FS-2447 FS-27 48 FS-2748 48: H Hopper · Lexan or Stainless Steel FHP -3368 FHP-3368 -3368: FS-3202 FS-3202: FS-330 1: FS-3301 P 18 Qt. (17L) capacity 18 Qt. (17L) capacity w/ 45° neck 36 Qt. (34L) capacity Pressure Disc Lexan for use with 18 Qt. (17L) Hopper [FS-3150] Stainless Steel for use with 18 Qt. (17L) Hopper [FS-2447] Stainless Steel for use with 36 Qt. (34L) Hopper [FS-2748] 20 Equipment and Accessory Guide CD-3252 CD-3252: A Used to counterbalance a Hose and Gun Assy. Balancer Assy. What fits me? G CDR -340 1: CDR-340 -3401 H Cake Decorator · Made specifically to fit CDR- Pumps Hose What fits me? T CD-3367 CD-3367: G Decorating · Straight-type Gun · 7/8” Threaded Tip What fits me? CD-3308 CD-3308: CD-33 11: CD-331 CD-33 11LH CD-331 1LH: G T Elbow · Pistol-type Gun Decorating · Pistol-type - Right handed Decorating · Pistol-type - Left handed Gun · 7/8” Threaded Tip CD-3258 CD-3258: CD-3259 CD-3259: CD-3260 CD-3260: CD-3266 CD-3266: FS-3 188 FS-31 88: Decorator Tip Decorator Tip Decorator Tip Decorator Tip Decorator Tip T-4040 -4040: T-404 1: -4041 120VAC · 60Hz 220VAC · 50Hz · · · · · #0 - #3 #4 - #6 #7 - #9 Euro Small Adaptor Turntable · Variable speed and Reversible direction T 279 Blau Road · Hackettstown · New Jersey 07840 · USA (TEL) 908.850.8444 · (FAX) 908.850.8445 888.edhard.1(USA & CANADA) [email protected] A-2201 04.07