Electrical

Transcript

ELECTRICAL 2 BEP MARINE EXALTO WIPER MOTOR JENSON AUDIO EQUIPMENT LED BULBS M-POWER BATTERY CHARGERS M- POWER INVERTERS TINNED CABLE www.ecsmith.com 19 THE BEP DC DIGITAL MONITORING SYSTEM Designed and manufactured by BEP, these state of the art full colour monitors are made to meet the systems monitoring requirements of today’s modern vessel and recreational vehicle. Complex AC and DC electrical installations onboard are becoming more common place. Additionally the increase in tank monitoring requirements for fuel, fresh, grey and black water, accurate monitoring of these systems is essential. The DCSM (No. 25345) and ACSM ( No. 25346) displays feature clear, extra large type face. This allows for more detailed on-screen information and increased clarity. The screen has backlighting for easy night time viewing. Specifications: • • • • 2.8” Colour QVGA LCD Input voltage 8-32VDC Dimensions Width 38mm (1.50") x High 40mm (1.57") Backlit keypad Range Highlights Monitors: • • • • • DC Power Meter Display Type • • • • • Displays voltages of multiple battery banks (0-32VDC) Displays charge and discharge(amps) of 2 battery banks Displays battery capacity in amp hours High/Low level alarms Configure the DCSM to show the data in analogue, digital and graphic form Circuit Status Tank Level • • • View the status of important circuits (on/off ) In graphic and numeric form Charge/discharge amps for two banks Capacity remaining in A/h and % Battery condition Tank fluid level Circuit status Features: • • • • 8 Generic, user configurable inputs Programmable high/low audio/visual alarms for volts, amps and tank levels Backlit keypad and dimmable screen Can be panel or surface mounted View tank level information for multiple tanks in numeric and graphic forms. Resettable when leaving boat No. 25345 20 SHUNT 450A / 50 mV shunt supplied supplied with No. 25345 83L x 45W x 44H mm INSTALLATION CABLE KIT 2 core screened cable in 2 lengths pre-terminated. No. 25282 No. 25310/5 5 m (16.45") cable No. 25310/10 10 m (32.9") cable THE BEP AC DIGITAL MONITORING SYSTEM Range Highlights • • • Monitors: • AC volts, amps and frequency Features: • • • • 3 Generic user configurable inputs Displays data in analogue, digital and graphic forms Output for load shedding Programmable high/low audio/visual alarms for each input • AC Power Meter AC Volts/Frequency • • • • Displays AC volts, amps frequency and power for two supplies with a third position for monitoring AC volts and frequency of a third supply Displays AC power in kW (true RMS) 2.8” Colour QVGA LCD Input voltage 832VDC Dimensions Width 38mm High 40mm Backlit keypad Displays AC voltage and frequency, 80-264 Vac 50 & 60 Hz CURRENT TRANSFORMER One CT-10-3 current transformer is supplied with No. 25346. If a twin line system is in use, a second CT must be ordered Supplied with part number 25346 Dimensions: 37.5 x 39.2 x 13.7 mm Hole size: 12 mm. No. 25161 AC Amps Alarms • • • • Displays Current for 2 x AC supplies (0-75A) No. 25346 High and low alarms for each input User selectable alarm levels Mutable AC-VSEN-4 TRANSFORMER The AC-VSEN-4 includes 3 voltage transformers for up to 3 voltage inputs. Supplied with part number 25346 CT-HD is available for systems with large mains cables, too large for CT-10-3 (No. 25161) (ordered separately). Dimensions: Ø 47 x 10.5 mm Hole size: 32 mm (1.25 in) Dimensions: 69 x 140 x 50 mm No. 25162 No. 25160 21 BEP TSI ULTRASONIC TANK SENDER The new BEP TSI Ultrasonic Tank Sender can be used on fuel (petrol or diesel), fresh water, grey water or black water tanks. One part number suits all tanks. Not suitable for tank depths less than 200mm The TSI is programmable for the following outputs, 240-33ohms, 10-180ohms, 10300ohms and 0-5volt. The TSI offers low profile and standard SAE 5 hole mounting pattern, allowing it to be retro fitted to practically all other sender brands. The TSI can be programmed for tank dimensions via a computer utilising BEP Marine’s proprietary TSI software, avoiding experimental tank filling on site. The TSI is configured to a 0-5v output and will connect straight into the BEP 600TLMN digital tank monitor. When configured to a 10-300ohms, 240-33ohm or 10-180ohm output the TSI can be connected to Teleflex, Faria, VDO and many other popular instrument brands. When connected to non-adjustable gauges the TS1 must be pre-calibrated. No. 25932 No. 25933 No. 25934 TS1 Ultrasonic Tank Sender MC6 TS1 Programmed USTS Programming Kit The TS1 is supplied pre-programmed to the following Settings. For most fluids, apart from petrol. Please see instructions for more info. Output 0-5 volts - Tank depth 0-2M BEP 701-MD MOTOR OPERATED Due to the increased load requirements and large increases in the cost of copper battery cable, the MD range of battery switches allows you to install the battery switch very close to the battery, reducing cable lengths to starter motor. They are also ideal for remote isolation of bow thrusters • • • • • • • Remote operation Battery switch can be mounted alongside battery, reducing cable lengths and cable sizes to starter motor. (Large cost saving in copper cables) Reduced installation labor, due to shorter battery cable runs Manual override option to meet CE requirements Power Draw: Switch off: 12mA. Switch on: 15 mA, switch operating 120 mA for 3 seconds @ 12 v nominal LED status identification for remote control switch Same capacities/specifications and mounting options as standard BEP battery switches Specifications: Continuous Rating: Intermittent Rating: Cranking Rating: Voltage Rating: Operation: Mounting: Ignition: Stud Size: Power Draw: Switch Operating: No. 33081 22 Dimensions: 275 Amps DC 475 Amps DC 1250 Amps DC 9.5 - 32 Volts On / Off Recessed or Surface Protected 2 x 10mm (3/8”) Tin Plated Cop per Studs and Nuts Switch Off 12mA Switch On 15mA 120mA for 3 seconds at 12 volts nominal 69L x 69W x 100.3H mm BEP720-MD MOTOR OPERATED The BEP 720-MD Motor driven remote operated battery switches (Patent Pending) due to the increased loading requirements on modern boats and large increases in the cost of copper battery cable, the new MD range of battery switches allows you to mount the battery switch very close to the battery, reducing cable lengths to starter motor. They are also ideal for remote isolation of bow thrusters. Features: Remote operation (easier access for battery control). Battery switch can be mounted alongside battery, reducing cable lengths and cable sizes to starter motor. (Large cost saving in copper cables). Reduced labour for fitting, due to shorter battery cabling (Cost saving). Manual override option to meet CE requirements. LED status identification for remote control switch. Same capacity/specification and mounting options as standard BEP battery switches. Utilises same inter-changeable labelling system as BEP battery switches. Specifications: Continuous Rating: 500 Amps DC Intermittent Rating: 700 Amps DC Cranking Rating: 2500 Amps DC Voltage Rating: 9.5 - 32 Volts Operation: On / Off Mounting: Recessed or Surface Ignition Protected Stud Size: 2 x 12mm (1/2”) Tin Plated Copper Studs and Nuts Power Draw Switch Off 12mA Switch On 15mA Switch Operating 120mA for 3 seconds at 12 volts nominal Dimensions: 102L x 102W x 109.5H mm No. 33084 REMOTE KEY Remote Key Switch For part numbers 33081 and 33084 It can be mounted standalone or within the Contour Connect panel range. No. 33085 WIRELESS REMOTE CONTROL You can now wirelessly operate your BEP motorized battery switches from a distance of up to 80 meters (250 feet) away Control up to 4 separate 5 A circuits; eg, 701/720-MD battery switches, anchor light, navigation lights, and courtesy lights. No more lifting hatches to turn on battery switches — it’s now all controlled from the remote key fob Control battery switches easily (On / Off ) from the dock Remote has a rolling code, for security No. 33086 23 LOW VOLTAGE SENSITIVE RELAY The LVSR is BEP’s latest innovation in battery protection. If your vessel’s primary voltage falls below 11 V, the LVSR automatically detects this and switches the essential circuit load to a second battery. When the LVSR detects a rise to 13 V on the primary battery, it reverts to its original state, and the LVSRs alert light switches off. The primary application for this is to ensure power is available for bilge pumps on unattended boats during heavy rain conditions. If a second battery is not connected to the LVSR, it will act as a low voltage disconnect. Ideal for charter boats. Avoids batteries being totally discharged. • • • • Avoids batteries being totally discharged Easy 3 wire connection at the battery. No need to bypass existing alternator wiring VSR’s have no volt drop. Conventional diode isolators incur a minimum of 0.6 V drop. Dimension: Volts: Rating: Engages: Disengages: 69 x 69 x x 50L x W x H 12V 40A 13V DC 11V DC No. 25278 DUAL OPERATION VSR AND EMERGENCY PARALLEL The High Current Remote Operated VSR (Voltage Sensitive Relay), uses the same operation as the motor driven Battery Switches. • • • • • Dual battery sensing Remote emergency parallel function: the 701-MDVS and 720-MDVS can be operated through a momentary button on the dash which will parallel the batteries for a preset time of 10 minutes. Once this 10 minutes has passed, if the voltage is up high enough for the voltage sensitive switch to operate, it will stay engaged. If not, it will disengage. Engine run sensing: VSR will engage when the voltage on either start or house battery reaches 13.7 volts. If the combined battery voltage drops below 13.0 volts and the engine is not running, after 5 seconds the contacts will open and stay open until the start or house battery voltage exceeds 13.7 volts. If the combined battery voltage drops below 12.2 volts and the engine is running, after 5 minutes the contacts will open and stay open until the start or house battery voltage exceeds 13.7 volts. If voltage drops below 13 volts and stays above12.2 volts on either start or house battery while engine is running, the VSR will stay engaged. Manual override option The advantages of using a high current VSR is that it will cover your dual battery charging requirements and emergency parallel operation in one unit Dimensions: 701-MDVS 68mm x 68mm x 101mm 720-MDVS 102mm x 102mm x 110mm Part No: Volts(V): Rating(A): Engages(V DC): Disengages(V DC): 701-MDVS 12 275 13.7 12.2 - 13.00 No. 33088 701-MDVS No. 33089 720-MDVS 24 720-MDVS 12 500 13.7 12.2 - 13.00 ATC BUS BAR The expandable ATC negative Bus uses the BEP Contour Lock system to allow it to be joined to the ATC fuse holder. This keeps wiring tidy and conveniently located. Current rating 100 No. 25394 702-MFH - MAXI FUSE HOLDER An economical way of fusing heavy loads 30-80 Amps. Ideal for battery charger outputs or mains feeds. 6 mm (1/4”) studs accept ring terminals and cables up to 25 mm2 (4 gauge). Fuse is clamped between tinned brass clamps for positive connection. Covers enclose exposed terminals to meet ABYC standards. 71 x 53 x 36 mm (2.8 x 2 x 1.42 in) No. 25405 HDBFH INLINE HEAVY DUTY FUSE HOLDER For installations where space is tight and fuse needs to be installed inline with the cable. Supplied with 8 mm (8G) tails for inline connections. An economical solution to heavy duty fusing. 80 x 55 x 15 mm (3.15 x 2.15 x .6 in) No. 25406 STECA PR The Steca PR 0505 is optimally suited for use in small solar home systems with module currents up to 5 A. A 75 Wp module can be connected, which easily allows operation of lamps, radios and a small television. All loads can be switched off using the manual load switch on the controller. The extremely low own consumption makes the Steca PR especially suitable for professional applications in telecommunications and traffic management technology. Since this is a serial controller, it is extremely flexible in the type of power source that can be connected. The electronic fuse makes the controller completely maintenance-free and robust.Recommended for use with one or two 35W flexi panel (two connected in parallel) Recommended for use with one flexi 70W No. 100336 STECA SOLARIX PRS PRS 1010 simplicity and high performance of the Steca Solarix PRS solar charge controller make it particularly appealing. At the same time, it offers a modern design and a convenient display, all at an extremely attractive price. Several LEDs in various colours emulate a tank display, which gives information on the battery’s state of charge. Here, Steca’s latest algorithms are employed, resulting in optimal battery maintenance. The Solarix PRS charge controllers are equipped with an electronic fuse, thus making optimal protection possible. They operate on the serial principle, and separate the solar module from the battery in order to protect it against overcharging. Recommended for use with two flexi 70W No. 100338 25 M-POWER PURE SINE WAVE INVERTERS: M-Power Inverters simply and silently convert 12V DC battery power to 230V AC electricity. Ideal for operating mains powered devices when you don’t have access to shore power. M-Power employs state of the art switch-mode conversion techniques to provide compact, efficient and reliable output power. Their pure sine wave output ensures compatibility with all AC appliances (modified sine wave / square wave inverters can cause issues with some appliances not operating, motors running hot, interference being transmitted through audio / visual systems and digital clocks running out of time!). Connections are via heavy duty studs on the rear of the unit. AC output connects directly to the UK socket on the front panel. A digital display provides the user with battery and inverter status information. MPower inverters interface with an optional remote panel. This provides inverter status information, remote on / off switch and an ignition inhibit circuit. SPECIFICATIONS: • • • • • • Pure sine wave output Extremely compact, efficient & reliable Easy to install and use Built in display provides battery and inverter status Huge surge power ability for starting difficult loads Optional remote on / off panel The diagram below illustrates the difference between a modified sine wave and a pure sine wave AC supply (as seen through a scope). The modified output (although it follows a similar pattern) has sharp edges that protrude outside the normal shape of the smooth sine wave. This causes interference and compatibility issues with many appliances. 700W 1400W Size: 90 x 185 x 310 mm Weight: 2.7Kg Output Wattage: 700 watts Input: 12 Volt Surge Capacity: 1400W AC Output Frequency: 50 +/- 0.5Hz AC Output Voltage: 230V AC +/-10% Optimal Efficiency: 90% No Load Current Draw: <1000mA DC Input Voltage Range: 10.5-15.5V DC Low Battery Alarm: Audible, 11V DC Low Battery Cut Out: 10.5V DC Remote Panel Optional: 01-8021 Size: 115 x 240 x 369 mm Weight: 4.7Kg Output Wattage: 1400 watts Input: 12 Volt Surge Capacity: 2800W AC Output Frequency: 50 +/- 0.5Hz AC Output Voltage: 230V AC +/-10% Optimal Efficiency: 90% No Load Current Draw: <1000mA DC Input Voltage Range: 10.5-15.5V DC Low Battery Alarm: Audible, 11V DC Low Battery Cut Out: 10.5V DC Remote Panel Optional: 01-8021 No. 102300 No. 102301 • • • • • Open Lead acid sealed Lead acid (Wet) VRLA Gel VRLA AGM Carbon Fibre 2000W Size: 115 x 240 x 418 mm Weight: 5.5Kg Output Wattage: 2000 watts Input: 12 Volt Surge Capacity: 4000W AC Output Frequency: 50 +/- 0.5Hz AC Output Voltage: 230V AC +/-10% Optimal Efficiency: 90% No Load Current Draw: <1000mA DC Input Voltage Range: 10.5-15.5V DC Low Battery Alarm: Audible, 11V DC Low Battery Cut Out: 10.5V DC Remote Panel Optional: 01-8021 Remote Control Panel Ignition Lock Out Switch: Yes Connections: RJ11 port Cable: 25ft Included Size: 50.8 x 63.5 x 35.2 mm Weight: 0.05Kg No. 102303 No. 102302 All M-Power Inverters have a 2 year no quibble warranty against defects and workmanship. 26 M-POWER BATTERY CHARGERS M-Power chargers are the culmination of over 20 years of experience in providing reliable charging solutions to the marine market. M-Power provides an adaptive four stage smart charge to recharge high capacity battery banks as quickly as possible. With auto-ranging power factor corrected electronics, M-Power can be plugged into any standard AC supply world-wide. It also has the ability to operate from fluctuating and poorly regulated power supplies, such as generators. The unit can independently charge up to three battery banks simultaneously (unlike competitive units, M-Power provides three full outputs and not a main plus one or two trickle outputs). M-Power’s informative front panel displays valuable information to you such as charge voltage, current and charging status (how many chargers actually tell you when they’ve finished charging?) - all this can be remotely displayed with the optional remote panel. Automatic fault diagnosis and fault code display is standard M-Power is the safest battery charger for your expensive battery bank and complex electrical system. What’s more, you can set specific charge programs for Pb, PbCa, Gel & AGM batteries. Even though M-Power has the smallest footprint on the market, it’s packed with many features found only in larger units. For example, equalization mode, which is designed to recondition and regenerate batteries you would otherwise throw away - saving you money on replacements. • 4 Stage Smart Charging for rapid recharging of multiple large capacity battery banks • Extremely compact design - perfect for modern engine rooms where weight / space is an issue • Auto-ranging AC input - can run from any standard AC supply, anywhere in the world • Full power factor correction for minimal AC draw and ability to handle fluctuating input power • Temperature compensation, battery type and selection of charge mode / power supply modes. • Optional remote panel and temperature sensor options available 20 Amp 10 Amp 40 Amp Size: 70 x 138 x 224mm Nominal Voltage: 12V DC Bulk Charge Voltage: 14.2 - 15.5V DC Float Charge Voltage: 13.4 - 13.8V DC Equalize Charge Voltage: 16V DC Standards Compliance: CE / E-Mark DC Outputs: x 2 AC Voltage Input: 90-265V AC AC Input Frequency: 47-63Hz Power Factor Correction: Full Temp Compensation: Three Settings Charge Efficiency: >80% Size: 70 x 170 x 250mm Nominal Voltage: 12V DC Bulk Charge Voltage: 14.2 - 15.5V DC Float Charge Voltage: 13.4 - 13.8V DC Equalize Charge Voltage: 16V DC Standards Compliance: CE / E-Mark DC Outputs: x 3 AC Voltage Input: 90-265V AC AC Input Frequency: 47-63Hz Power Factor Correction: Full Temp Compensation: Manual Or Auto Charge Efficiency: >80% Size: 70 x 170 x 250mm Nominal Voltage: 12V DC Bulk Charge Voltage: 14.2 - 15.5V DC Float Charge Voltage: 13.4 - 13.8V DC Equalize Charge Voltage: 16V DC Standards Compliance: CE / E-Mark DC Outputs: x 3 AC Voltage Input: 90-265V AC AC Input Frequency: 47-63Hz Power Factor Correction: Full Temp Compensation: Manual Or Auto Charge Efficiency: >80% No. 102308 Remote Display Panel Optional: 102310 Temperature Sensors Optional: 102311 Remote Display Panel Optional: 102310 Temperature Sensors Optional: 102311 No. 102304 No. 102305 60 Amp Size: 70 x 170 x 340mm Nominal Voltage: 12V DC Bulk Charge Voltage: 14.2 - 15.5V DC Float Charge Voltage: 13.4 - 13.8V DC Equalize Charge Voltage: 16V DC Standards Compliance: CE / E-Mark DC Outputs: x 3 AC Voltage Input: 90-265V AC AC Input Frequency: 47-63Hz Power Factor Correction: Full Temp Compensation: Manual Or Auto Charge Efficiency: >80% Remote Display Panel Optional No. 102310 Temperature Sensors Optional No. 102311 Temperature Sensors Optional: 102311 No. 102306 All M-Power battery chargers have a 2 year no quibble warranty against defects and workmanship. For 24 Volt Units Please See Page 28 27 10AMP 24VOLT 20AMP 24VOLT 30AMP 24VOLT Size: 70 x 170 x 250mm Nominal Voltage: 24V DC Bulk Charge Voltage: 28.4 - 31V DC Float Charge Voltage: 26.8 - 27.6V DC Equalize Charge Voltage: 32V DC Standards Compliance: CE / E-Mark DC Outputs: x 3 AC Voltage Input: 90-265V AC AC Input Frequency: 47-63Hz Power Factor Correction: Full Temp Compensation: Manual Or Auto Charge Efficiency: >80% Size: 70 x 170 x 250mm Nominal Voltage: 24V DC Bulk Charge Voltage: 28.4 - 31.0V DC Float Charge Voltage: 26.8 - 27.6V DC Equalize Charge Voltage: 32V DC Standards Compliance: CE / E-Mark DC Outputs: x 3 AC Voltage Input: 90-265V AC AC Input Frequency: 47-63Hz Power Factor Correction: Full Temp Compensation: Manual Or Auto Charge Efficiency: >80% Size: 70 x 170 x 340mm Nominal Voltage: 24V DC Bulk Charge Voltage: 28.4 - 31.0V DC Float Charge Voltage: 26.8 - 27.6V DC Equalize Charge Voltage: 32V DC Standards Compliance: CE / E-Mark DC Outputs: x 3 AC Voltage Input: 90-265V AC AC Input Frequency: 47-63Hz Power Factor Correction: Full Temp Compensation: Manual Or Auto Charge Efficiency: >80% Remote Display Panel Optional: 102310 Temperature Sensors Optional: 102311 Remote Display Panel Optional: 102310 Temperature Sensors Optional: 102311 Remote Display Panel Optional: 102310 Temperature Sensors Optional: 102311 No. 102329 No. 102330 No. 102331 SMARTGAUGE BATTERY MONITOR: While there are many battery monitors available that count ampere hours to display state of charge (by using a current measuring shunt), one drawback can be their accuracy over extended time periods. If you are prepared to periodically re-synchronise your monitor, then the BEP 600-DCM is a good example. If however, you don’t want to worry about whether your monitor is telling the truth or not and don’t want to have to regularly remind it of your batteries state of charge, then the SmartGauge is the ideal solution. Designed by Merlin’s own R&D team, the unit uses an advanced computer algorithm to display voltage (2 battery banks) and state of charge (1 battery bank), using just two or three wires. There is no need to cut into heavy negative cables to install a shunt, as the unit doesn’t require one. In addition to being very easy to install, SmartGauge is also very easy to operate – perfect if you’re not familiar with battery technology. The algorithm within the unit self compensates for changes in a batteries health and charge efficiency factor over time, ensuring that the unit remains accurate throughout the life of the installation. SmartGauge is suitable for both 12 and 24V systems and provides user settable alarms. SmartGauge can also be upgraded to control its own intelligent split charging system – see SmartBank Advanced. • • • • • The most advanced, yet simplest to use battery state of charge monitor currently available Unlike ampere hour counting battery monitors, Smart Gauge cannot run out of synchronization with your batteries Displays voltage and charge status as a percentage on an easy to read, LED screen User programmable alarm functions. Can be used to control a battery combining split charging system (Smart Bank Advanced) Specifications: Product Code: Supply Voltage Range: Supply Current (Sleep Mode): Supply Current (Display On): Operating Temperature Range: Accuracy For State Of Charge (Charge): Accuracy For State Of Charge (Discharge): Accuracy Voltage: Dimensions (Front Panel): Dimensions (Body): Total Depth: Weight: Protection Rating: Standards: 19-1001 8-40V DC 5mA <15mA -25 To +85C +/- 10% +/- 5% +/- 0.5V DC 110 x 76mm 95 x 64mm 28mm 0.2Kg IP20 (Front Panel IP65) CE, ISO7637-2 No. 102312 All M-Power SmartGuard have a 2 year no quibble warranty against defects and workmanship. 28 SMARTBANK ADVANCED SYSTEM: SmartBank Advanced is an intelligent split charging system that interfaces with the SmartGauge battery monitor. The system consists of either one or two 200A rated split charging contactors (depending on your battery setup) and a small control CPU. The CPU connects to the SmartGauge monitor using a RJ11 telephone type cable. Based on what SmartGauge knows about battery state of charge and voltage, SmartBank Advanced continuously and automatically adjusts its settings to ensure the domestic batteries receive as much charge as is possible, whilst ensuring priority is always given to the starter battery. It also prevents the domestics cross discharging the starter battery. In a SmartBank Advanced system, the SmartGauge monitor will also automatically display split charging status. SmartBank advanced can either be purchased as an upgrade if you already own a SmartGauge, or as a full kit, complete with the monitor. • • • • Provides priority based, zero voltage loss split charging for multiple battery banks Emergency parallel feature Unique, shunt-less battery monitoring The most advanced stand-alone split charging system available • • • • • Open Lead acid sealed Lead acid (Wet) VRLA Gel VRLA AGM Carbon Fibre Specifications: Split Charge Contactor(s): Power Consumption (Standby): Power Consumption (Split Charging Connected / Display Awake): Standards: No. 102315 No. 102316 No. 102317 No. 102318 No. 102319 No. 102320 No. 102321 No. 102322 200A Continuous <10mA 17mA CE Ex SmartGauge 2 battery banks, 12V Ex SmartGauge 3 battery banks, 12V Ex SmartGauge 2 battery banks, 24V Ex SmartGauge 3 battery banks, 24V Inc SmartGauge 2 battery banks, 12V Inc SmartGauge 3 battery banks, 12V Inc SmartGauge 2 battery banks, 24V Inc SmartGauge 3 battery banks, 24V Smart Gauge plugs into Smart Bank Advanced via a straight forward RJ11 data cable (telephone type). All M-Power SmartBank have a 2 year no quibble warranty against defects and workmanship. BOXCLEVER - PREWIRED AC CONSUMER UNITS With load shedding, AC interlocks, PRODUCT HIGHLIGHTS combi inverter / chargers and multiple AC sources becoming more • Complete range of pre-built AC electrical cabinets to suit widespread on today’s boat and specialist most mobile applications. vehicles, 230V consumer wiring is getting • Complex internal cabling precomplicated! Our Box Clever range of AC completed. distribution consumer units are an Off The • High quality Hager compoShelf solution designed to simplify the nents used. installation process with all difficult internal • Each unit supplied with a full wiring pre-completed. Each IP55 wiring plan and installation rated consumer unit is supplied with clearly guide. labelled terminals, an internal schematic and installation wiring plan. We use quality Hager components ensuring the highest possible level of safety compliance with European legislation. There is a Box Clever unit to cover most common applications, however if you cannot see what you need, please contact our sales team, as we also produce units to custom requirements No. 102324 Basic consumer unit allowing the addition of 230V power to a vehicle or boat. Incoming power runs via a galvanic isolator (on marine installations), to the RCD. Two circuit breakers are provided for loads such as ring main, battery charger etc. Supplied in waterproof box, fully labelled, wired and with 3 x waterproof cable glands. The expanded version (15-3003) is supplied with 2 x additional breakers and waterproof cable glands. Note shore power inlet socket, galvanic isolator and AC sockets are not supplied. 29 JENSEN MARINE STEREO Type JMS2212 This stereo has a waterproof controller (IPX6) and a separate water resistant amplifier/tuner unit. In this way you can install the controller even in areas with limited space. The separate unit can be mounted up to 2.7 metres away from the controller. The JMS2212 features an AM/FM tuner, an Aux-input and a USB interface, so you can listen to MP3 or WMA files from an MP3 player/USB stick or external hard drive. Don’t forget to order the unique USB/Aux-in interface (cat. no. JENAUX) then! You can also connect your iPod with the optional iPod/iPhone cable (cat.no. JDABIPDL) and scroll through the folders and files with the buttons on the radio (full control). Controller comes complete with cover. This stereo complies with the ASTM standards for UV exposure and salt water. Features: • • • • • • • • • • • • AM/FM tuner USB interface supports MP3 and WMA formats Aux input full iPod control / iPod/iPhone ready with iPod cable (JDABIPDL, optional) sealed PCB pre-wired for Jensen remote JWR 200 blue LCD and button illumination warning signal at low battery voltage zero current memory draw non-volatile memory for presets and user settings Controller w x h x d : 131 x 94 x 26 mm Micro-processor d x w x h : 205 x 210 x 50 mm No. 102820 JENSEN MARINE STEREO Type MSR3012 With this modern design stereo you can enjoy your favourite music on AM/FM tuner or the CD/MP3 player. When you plug your iPod or iPhone into the stereo by means of the original Apple USB cable you can scroll through the folders and files with the buttons on the radio (full control). You can also connect your MP3 player through the AUX-input. The PCB is sealed and therefore suitable for marine applications. The modern CD/MP3 player is equipped with a 40 seconds Electronic Skip Protection; this way you won’t miss one single note caused by severe weather. Includes white waterproof radio cover (IPX5). Features: • • • • • • • • • • • • • AM/FM tuner and CD/MP3 player front Aux and USB input full iPod/iPhone control / iPod/iPhone ready 40 second skip protection silver coloured faceplate pre-wired for Jensen remotes MWR75 / MWR100 / MRF27 sealed PCB blue LCD and button illumination warning signal at low battery voltage zero current memory draw non-volatile memory for presets and user settings Dimensions b x h : 190,5 x 57,15 mm Built-in dimensions. b x h x d : 184,15 x 50,8 x 165,10 mm No. 102821 30 JENSEN MARINE STEREO Type JMS7010 The JMS7010 is a waterproof, IPX6 rated stereo that is durable enough to withstand the harsh marine environment. The Marine Stereo offers an AM/FM tuner, USB input, Aux input and an iPod/iPhone connection (at backside), allowing you to listen to your personal music. When you plug your iPod/iPhone into your new Marine Stereo you can fully control the iPod/iPhone using the stereo controls. For the iPod/iPhone connection the JDABIPDL iPod Adapter Cable is required (sold separately). Please note that the JMS7010 only works with the special JMS accessories. The 40 Seconds of Electronic CD Skip Protection is ideal for heavy weather. The stereo comes complete with waterproof grey radio cover. Features: • • • • • • AM/ FM tuner and CD/MP3 player WMA, WAV, MP3 SIRIUS Satellite Radio Ready Aux input on the front side USB input allows connection of jump drive for digital music and supports MP3/WMA/WAV formats. Full iPod/iPhone control iPod/iPhone ready (iPod/iPhone cable is sold separately) 200 Watts (4x50w) • • • • • • • • • 40 seconds skip protection Sealed PCB Prewired for remote JWR200 blue LCD and button illumination Non-volatile memory for presets & user settings Warning signal at low voltage zero current memory draw Dimensions w x h : 220 x 93 mm Built-in dimensions w x h x d: 184,1 x 50,8 x 174,6 mm No. 102822 JENSEN MARINE DVD PLAYER Type DV2011 The DV2011 is ideal for those seeking stereo and video capability. The single DVD/CD offersan AM/FM tuner and plays CD's (incl. MP3/WMA) and DVD's. The player has electronic skip protection and front auxiliary input along with a detachable faceplate. Easily connecting the DVD player to your TV by the RCA outputs offers you to sit back and watch any DVD content on your onboard television. The DV2011 comes with a credit card size remote control. Prewired for remote MWR 75. Features: • • • • • • • • • • • • • AM/ FM tuner and DVD/CD player plays CD’s, WMA, MP3 CD’s and DVD’s Aux input on the front side 4 speaker output 160 Watts (4x40w) Prewired for remote MWR 75 wireless remote control included detachable faceplate subwoofer output (RCA) 2 composite video outputs (RCA) 1 composite video input (RCA) Dimensions w x h : 190 x 57 mm Built-in dimensions w x h x d: 184,1 x 50,8 x 165,1 mm No. 102823 31 JENSEN MARINE AMPLIFIERS For an even better sound, or for the addition of extra speakers, you can submit an amplifier in your sound system. Jensen Marine offers two amplifiers. They both have variable low and high pass filters (40-300 Hz) and an electric protection circuit that safeguards against short circuits, DC-offset and thermal overload. Power 400 (pos. 1): L x w x h : 241.3 x 228.6 x 63.5 mm Power 760 (pos. 2): L x w x h : 317.5 x 228.6 x 63.5 mm No. 102825 1 Amplifier, 2 channels 400 No. 102826 2 Amplifier, 4 channels 760 JENSEN MARINE SUBWOOFERS Since nothing sounds better than a track that really pumps out the bass, we advice a Jensen waterproof marine subwoofer. The amplified marine subwoofer (pos. 1) is water resistant (IPX5). It meets the ASTM standards for salt spray exposure and for UV exposure. It has conformal coated circuit boards. The subwoofer can be mounted vertical as well as horizontal. The waterproof (IPX6) non-amplified subwoofer is made of corrosion and UV resistant materials according to the ASTM standards: an aluminium chassis with silver powder coating finish. The subwoofer can be mounted with or without the ABS grill (cover) with a diameter of 254 mm. This subwoofer requires a seperate amplifier. Dim. subwoofer pos. 1 L x w x d = 406 x 220 x 100 mm Mounting hole pos. 2 228.6 mm (O.D: 254 mm) No. 102827 No. 102828 No. 102829 No. 102830 No. 102831 1 Amplified subwoofer 200 MXA6BA 2 Non-amplified subwoofer 300 MSW10S 3 RCA cable 1,2 m RCA120 3 RCA cable 2,5 m RCA250 3 RCA cable 5,0 m RCA500 JENSEN MARINE SPEAKER Type MS5006 This compact slimline speaker is waterproof, UV resistant and corrosion resistant. Ideal for outdoor use, like all Jensen speakers! This speaker has a 2,9 oz magnet. Available in white and silver. N.B: this speaker is sold Singly. 32 Mounting Hole Mounting mm Depth (mm) Part No. Colour Watt Ø (mm) No. 102834 Black 30 150 115 40 No. 102835 White 30 150 115 40 JENSEN MARINE SPEAKERS Type AMS602 These coaxial, waterproof speakers are available in black and white. The one-piece-design speakers are made of UV resistant plastic to resist fading from the sun and the speakers are corrosion resistant. With a 10 oz magnet. N.B: this speaker is sold Singly. Mounting Hole Mounting mm Depth (mm) Part No. Colour Watt Ø (mm) No. 102837 Black 60 165 130 60 No. 102838 White 60 165 130 60 JENSEN MARINE SPEAKERS Type MS6007 This stylish speaker is UV and salt spray protected. The speaker has a one-piece-moulded chassis and a 10 oz magnet. Available in stylish silver, bold black or clear white. N.B: this speaker is sold Singly. Mounting Hole Mounting mm Depth (mm) Part No. Colour Watt Ø (mm) No. 102840 Silver 60 165 130 59 No. 102841 Black 60 165 130 59 No. 102842 White 60 165 130 59 JENSEN MARINE SPEAKER Type MSX60SR The MSX series exceed every expectation sound-wise! The shiny chromed titanium tweeter enables a christal clear sound. The design of this speaker set is very eye-catching. The cone is trendy blue and the speaker covers are of a light silver matt finish. Naturally this set also is UV and salt spray protected according to ASTM standards. The maximum total output is 130W. The speaker has a 11 oz magnet and is supplied complete with two 3 meter cables and comes in a representative box. N.B: these speakers are sold as a set of two speakers. Part No. Watt Ø (mm) No. 102844 130 165 Mounting Hole Mounting mm Depth (mm) 130 59 JENSEN MARINE SPEAKER Type MSX65R The MSX series exceed every expectation sound-wise! This 150 Watt speaker is the best speaker in the high end MSX series. With a frequency range of 65Hz-20kHz your ears won’t miss a single high or low tone. The speaker is equipped with a 11" magnet and contains a polypropylene woofer. N.B: these speakers are sold as a set of two speakers. Package contains white and silver grilles Part No. Watt Ø (mm) No. 102846 150 165 Mounting Hole Mounting mm Depth (mm) 130 59 33 SPEAKER CABLES Cables to connect your Jensen speaker set to your Jensen stereo. Available in 2 x 1,5 mm2 or 2 x 2,5 mm2. Can be supplied in 100m, 50m or 20m lengths. No. 102847 No. 102848 No. 102849 No. 102850 No. 102851 No. 102852 Red/Black 1.2mm² Red/Black 1.2mm² Red/Black 1.2mm² Transparent 2.5mm² Transparent 2.5mm² Transparent 2.5mm² 30m 50m 100m 30m 50m 100m JENSEN MARINE REMOTE CONTROL Wired, with or without display These remote controls can be used in all exterior applications and can be easily mounted in any convenient location. They are waterproof (IPX6) and can be exposed to UV and salt water. With the MWR100 stereo functions are shown on a sunlight readable LCD display. Both remotes have blue button illumination and are CE certified. Installation is easy by means of a spin-on retaining ring. 5.5 meters connection cable included. The MWR100/ MWR75 corresponds with the MSR-series, the JWR200 is only suitable for the JMS series. The Y-cable is necessary if you want to connect a MWR75 or MWR100 remote control to your stereo in combination with the wireless remote control. When the distance between your stereo and your wired control is quite large, the nearly 6 meters long extension cable can be useful. Diam. MWR100 (pos. 1) Diam. MWR75 (pos. 2) : 90 mm : 60 mm Part No. Description No. 102854 No. 102855 No. 102856 No. 102857 No. 102858 No. 102859 No. 102860 With Display With display for the JMS series Without Display Y-cable for connecting several remotes Extension cable 5.8 m for remote control Y-cable for connecting the JWR200 (JMS series) Extension cable 5.8 m for remote control JWR200 (JMS series) Mounting Hole mm Mounting Depth (mm) 70 70 50 32 32 32 JENSEN MARINE IPHONE/ IPOD/ MP3 STORAGE POCKET The waterproof JSP20 storage pocket protects your music player from shocks and getting wet. With the JSP20 iPhone/iPod/MP3 storage pocket you can always keep your music players dry and it is possible to connect your music player to your stereo. You will need the required iPod cables (sold separately to do so). You can integrate the JMS2212 stereo with the storage pocket, see photo. Ask our sales department Parts for the compatibility of your iPod product in combination with JMS2212. The iPhone and the JMS2212 are not included. Part No. Colour No. 102861 No. 102862 Silver Black 34 Description Waterproof iPod/ MP3 storage pocket Waterproof iPod/ MP3 storage pocket Dimensions wxhxd (mm) Mounting dimensions (mm) bxhxd 169,6 x 18,5 x 148 169,6 x 18,5 x 148 149,8 x 106,4 x 44,9 149,8 x 106,4 x 44,9 JENSEN MARINE RADIO COVERS This radio cover with spring loaded flip-up door protects your stereo from salt water. Made of UV-durable plastic to resist fading in the sun. Part No. Colour Mounting hole w x h (mm) No. 102863 No. 102864 Black White 215.9 x 86.6 215.9 x 86.6 JENSEN MARINE CABLES USB/Aux-in interface / iPod cable The USB / 1/8"Aux-in interface set is a handy accessory with your JMS22012 and JMS7010 stereo. With the over three meters cable, you can install a USB interface e.g. on your fly bridge. The interface has a waterproof cover (IPX5) and is made of Corrosion and UV resistant materials. The iPod-cable is an essential accessory if you want to connect your iPod to your Jensen Marine stereo. It enables you to have full control over your iPod functions with your stereo. The JENAUX has a waterproof storage cover. Mounting hole USB / Aux-in interface:38 mm Part No. No. 102865 No. 102866 No. 102867 Description 1. USB /Aux-in interface set incl. 3 m cables (through hull fitting) 2. iPod cable (3.5 m) iPod cable (3.5 m) for the JMS Series (black) JENSEN MARINE ANTENNAS Both AM/FM antennas are easy to mount and come complete with connection cables. The antenna on 2 is not suitable for inside use of steel or aluminium vessels Part No. No. 102868 No. 102869 Description 1 .Rubber mast antenna incl. 1,5 m cable 2. Amplified antenna incl. 2 m cable COMPLETELY WEATHERPROOF JUNCTION BOX Neoprene rings ensures waterproof seal. Complete with 8 pole connector strip. No. 32602 35 Self parking Heavy Duty wiper for either bulkhead or through glass mounting. The wiper can be supplied with spindle lengths of 25mm, 50mm and 75mm. The system is designed and tested for a combination of 600mm arms and blades. The 215BD is a pendulum or single spindle unit. It can easily be converted to a pantograph system with the external pantograph plate that comes with the suitable wiper arm. The wiper motor unit is fully enclosed in a waterproof housing. The housing is rated at IP66. • • • • • 2 Speed, self parking Protection class IP 66 Available in 12V or 24V Heavy Duty 15Nm motor CE approved Voltage: CE approval: Torque: Power consumption: Insulated ground: IP rated: Bulkhead mount: Glass mount: Max. arm length: Max. blade length: Part No. No. 102800 No. 102801 No. 102802 No. 102803 No. 102804 No. 102805 12 / 24 Yes 15Nm 15W Standard IP66 Yes Yes 600 mm 600 mm Shaft Length (mm) 25 25 50 50 75 75 Two speeds: Self-Park: Wiping arcs 40-110: Drive shaft sleeve: Idler spindle: Centre distance: Driven shafts: Compatible arm: Torque Nm 15 15 15 15 15 15 Power Consumption 15 15 15 15 15 15 WIPER ARMS For the 215BD high quality arms and blades are available. The arms are made of stainless steel and have a black coating to avoid blinding glare. The blades are made of rubber and have a black carrier. Part No. No. 102806 No. 102807 No. 102808 No. 102809 No. 102810 No. 102811 Wiper Arm Pendulum Pendulum Pendulum (adjustable tip) Pendulum (adjustable tip) Pantograph Pantograph WIPER BLADES Part No. No. 102812 No. 102813 No. 102814 No. 102815 No. 102816 No. 102817 No. 102818 36 Length 300 350 400 450 500 550 600 Length 330-450 450-600 330-450 450-600 330-450 450-600 Yes Yes 10º increments 16 mm External mounting plate (supplied with pantograph arms) 45 mm (external pantograph plate) Single See table of details LED REPLACEMENT BULBS With the G4 Super Bright Chip LED’s Replacement Bulb, you can instantly replace all your halogen lights with LED’s. The G4 comes with side pins or with back pins on the aluminium housing to fit any fixture. The back pins are mainly used in reading lights as the side pins are mainly used in down lighters. Using merely 1,2 Watts, they provide a light output comparable with a 10 Watt halogen light. No. 21760 Side Pins Warm White 3200K 10V-15V AC/DC No. 21762 Back Pins Warm White 3200K 10V-15V AC/DC LED REPLACEMENT BULBS With the MR11 and MR16 7 Super Bright Chip LED’s Replacement Bulb, you can instantly replace all your halogen lights with LED’s. Using merely 1,2 Watts, they provide a light output comparable with a 10 Watt halogen light. No. 21764 MR11 Warm White 3200K 10V-15V AC/DC No, 21766 MR16 7 Warm White 3200K 10V-30V AC/DC 18 LED BAYONET B15 The 18-LED bayonet spotlight has been designed to use in bulkhead lights and ceiling lights as light is projected in all directions. Regulated from: Diameter: Length: Power consumption: No. 21968 No. 21969 10-30V 22mm, 34mm (excluding cap) 3.0W Cool White Ba15d Warm White Ba15d 5800-6200K 2800-3200K 36 LED BAYONET B15 The 36-LED bayonet spotlight has been designed to use in bulkhead lights, ceiling lights as light is projected in all directions. Regulated from: Diameter: Length: Power consumption: No. 21970 No. 21971 10-30V 22mm, 45mm (including cap) 1.8W Cool White Ba15d Warm White Ba15d 5800-6200K 2800-3200K 37 BA15D AND BA15S 18 DOUBLE CHIP LED’S REPLACEMENT BULB Will replace your conventional light bulb, instantly converting your navigation lights to LED navigation lights for boats up to 12 meters. As each LED has two Chips the Bulb has the same light output compared with 36 normal LED’s. The LED bulbs consume merely 2 Watts and have the same light output as the conventional 10 Watt light bulb. Light Source: Power Source: Power consumption: LED Colour Options: Material: Fitting: 18pcs Double Chip Super Bright LED’s 10V-15V/DC 2 Watt White Anodized Aluminium BA15D, BA15S No. 100230 BA15D All Around White No. 100231 BA15S All Around White FESTOON 18 DOUBLE CHIP LED’S REPLACEMENT BULB Will replace your conventional light bulb, instantly converting your navigation lights to LED navigation lights for boats up to 12 meters. As each LED has two Chips the Bulb has the same light output compared with 36 normal LED’s. Available colours are White, Red, Green & Two Colour Red/Green to fit all versions of the navigation lights. The LED bulbs consume merely 2 Watts and have the same light output as the conventional 10 Watt light bulb. Light Source: Power Source: Power consumption: LED Colour Options: Colour Red Material: Fitting: toon 18pcs Double Chip Super Bright LED’s 10V-15V/DC 2 Watt All Around Red, Green, White & Two & Green Anodized Aluminium A15D, BA15S, Festoon T13x44 & Fes- No. 100232 No. 100233 No. 100234 No. 100235 All Around White for Hella Lights (UK) Two Colour Red & Green for Hella Lights (UK) All Around Green for Hella Lights (UK) All Around Red for Hella Lights (UK) No. 100240 No. 100241 No. 100242 No. 100243 All Around White for Aqua Signal Lights Two Colour Red & Green for Aqua Signal Lights All Around Green for Aqua Signal Lights All Around Red for Aqua Signal Lights Aqua Signal type 38 Hella type G4 LED REPLACEMENTS Lighting for use in boats. The G4 halogen is one a common lamps used in ceiling lights, wall lights, downlights and reading lights and is easily replaced with an LED alternative. It is easily identified as a small glass lamp with two short pins spaced 4mm apart. 6 LED SIDE PIN G4 The most popular LED G4, the 6-LED G4 has been designed to replace the light output from a 10W G4 halogen. 6 LED REAR PIN G4 The most popular LED G4, the 6-LED G4 has been designed to replace the light output from a 10W G4 halogen. 10 LED SIDE PIN G4 The 10-LED G4 has been designed to replace a 10W G4 halogen but provide approximatley 65% more light. . 10 LED REAR PIN G4 The 10-LED G4 has been designed to replace a 10W G4 halogen but provide approximately 65% more light. . Regulated from: Diameter: Power consumption: Regulated from: Diameter: Power consumption: Regulated from: Diameter: Power consumption: Regulated from: Diameter: Power consumption: 10-30V 23mm 1.5W 10-30V 23mm 1.5W 10-30V 30mm 2.0W 10-30V 30mm 2.0W No. 21974 Cool White No. 21975 Warm White No. 21976 Cool White No. 21977 Warm White No. 21978 Cool White No. 21979 Warm White No. 21980 Cool White No. 21981 Warm White 15 LED SIDE PIN G4 The 15-LED G4 has been designed to replace a 20W G4 halogen. Ideal for ceiling lights. Designed to sit sideways into the light fitting. 15 LED REAR PIN G4 The 15-LED G4 has been designed to replace a 20W G4 halogen. Ideal for ceiling lights. Designed to sit straight back into the light fitting. Regulated from: 10-30V Diameter: 44mm Power consumption: 2.8W 6 LED 42MM FESTOON (SLIM) The 6-LED 42mm slim festoon provides the light output from a 5W G4 halogen for a fraction of the power use. 6 LED 42MM FESTOON The 6-LED 42mm festoon provides the light output from a 10W G4 halogen for a fraction of the power use. Regulated from: Diameter: Power consumption: 10-30V 44mm 2.8W No. 21984 Cool White No. 21985 Warm White No. 21986 Cool White No. 21987 Warm White Regulated from: Length: Power consumption: 10-30V 42mm 0.9W No. 21988 Cool White No. 21989 Warm White Regulated from: Length: Power consumption: 10-30V 42mm 1.5W No. 21990 Cool White No. 21991 Warm White 39 MARINE GRADE TINNED CABLE The culprit behind unreliable marine electrical systems is standard automotive cable. It’s simply not designed to resist the harsh marine environment and salt water atmosphere. Internal copper conductors turn black, brittle and break down (leading to fire). Our Lifetime UL1426 boat cable features fully tinned conductors to prevent corrosion. Ultra fine stranding Part No makes our cable extremely flexible, aiding its installation and resistance to vibration. Insulation resistant to oil, acid, UV light, fuel and most chemicals. Under direct flame (even from a blow torch) insulation will simply form a crust to prevent the cable short circuiting (self extinguishing). We offer a wide range of sizes and lengths to cover everything from the smallest wiring modification to entire re-wires. For boat builders we can supply bulk spools. Lifetime meets all the latest safety standards for marine applications including Lloyds, ABYC, DNV and CE specifications. Multi core cables are perfect for DC lighting feeds and 230V AC mains cabling. PRODUCT HIGHLIGHTS • • • • • • Fully tinned conductors - guaranteed for life against corrosion. Excellent vibration resistance and extremely flexible - for ease of installation. Insulation resistant to oil, acid, UV light, fuel and most chemicals. Sold on 30m spools or (bulk spools to special order) Lifetime is a one time purchase not a consumable like normal cable. UL 1426 boat cable. Complies to CE, USCG , ABYC, DNV Lloyds and National Fire Prevention Association standard. Description Colour Size Coil Part No White Sleeve Two Core No. 103000 18AWG Red 0.8mm² 30m No. 103021 N0. 103001 18AWG Black 0.8mm² 30m No. 103002 16AWG Red 1mm² No. 103003 16AWG Black No. 103004 14AWG No. 103005 Colour Size Coil Flat Duplex 2 x 16AWG R/B 1mm² 30m No. 103022 Flat Duplex 2 x 14AWG R/B 2mm² 30m 30m No. 103023 Flat Duplex 2 x 12AWG R/B 3mm² 30m 1mm² 30m No. 103024 Flat Duplex 2 x10AWG R/B 5mm² 30m Red 2mm² 30m Part No White Sleeve Two Core Colour Size Coil 14AWG Black 2mm² 30m No. 103025 Round Duplex 2 x 16AWG R/B 1mm² 30m No. 103006 12AWG Red 3mm² 30m No. 103026 Round Duplex 2 x 14AWG R/B 2mm² 30m No. 103007 12AWG Black 3mm² 30m No. 103027 Round Duplex 2 x 12AWG R/B 3mm² 30m No. 103008 10AWG Red 5mm² 30m No. 103028 Round Duplex 2 x 10AWG R/B 3mm² 30m No. 103009 10AWG Black 5mm² 30m No. 103010 8AWG Red 8mm² 30m Part No White Sleeve Three Core Colour Size Coil No. 103011 8AWG Black 8mm² 30m No. 103029 Flat Triplex 3 x 16AWG W/B/G 1mm² 30m No. 103012 8AWG Green 8mm² 30m No. 103030 Flat Triplex 3 x 14AWG W/B/G 2mm² 30m No. 103013 6AWG Red 13mm² 30m No. 103031 Flat Triplex 3 x 12AWG W/B/G 3mm² 30m No. 103014 6AWG Black 13mm² 30m No. 103032 Flat Triplex 3 x 10AWG W/B/G 5mm² 30m No. 103015 4AWG Red 19mm² 30m Part No White Sleeve Three Core Colour Size Coil No. 103016 4AWG Black 19mm² 30m No. 103033 Round Triplex 3 x 14AWG W/B/G 1mm² 30m No. 103017 2AWG Red 32mm² 30m No. 103034 Round Triplex 3 x 12AWG W/B/G 2mm² 30m No. 103018 2AWG Black 32mm² 30m No. 103035 Round Triplex 3 x 10AWG W/B/G 3mm² 30m No. 103019 1AWG Red 40mm² 30m No. 103020 1AWG Black 40mm² 30m 40 Colour codes: R/B = Red/Black inner core cable colours W/B/G = White/Black/Green inner core cable colours To ensure a reliable and safe system, it is essential that cabling is carefully sized. This guide makes this quick and easy to do. The tables below provide sizing at a glance. Measure from your power source to the load and back again to obtain total circuit length (power source could be a switch panel, main bus bar or battery switch). Critical items(eg nav lights, bilge pump, instruments etc) use 3% voltage drop. For non-critical loads (eg fridge, lights etc), use 10%. If you cannot determine the right cable from the charts, use the calculation in the blue box (right). Work out the CM value and read off against the chart on the right. For example, take a 12V 40’ long circuit, driving an 18A non-critical load (Note: Length is calculated always in feet (divide metres by 0.3048): 10.75 x 18 x 40 = 7740 divide by 1.2= 6450. The nearest cable on the chart is 12AWG (3mm2).. AWG SQ MM AWG CM AREA AMPACITY INSIDE ENGINE SPACE AMPACITY OUTSIDE ENGINE  SPACE 18 0.8 1600 17 20 16 1 2600 21 25 14 2 4100 30 35 12 3 6500 38 45 10 5 10500 51 60 8 8 16800 68 80 6 13 26000 102 120 4 19 42000 136 160 2 32 66500 178 210 1 40 83690 208 245 1/0 50 105600 242 285 2/0 62 133100 280 330 3/0 81 167800 327 385 4/0 103 211600 378 445 CM = (K x I x L) / E K = Constant (10.75). I = Current (amps). L = Length. E = Voltage Drop 3% @ 12V DC = 0.36, 10% @ 12V DC = 1.2, 3% @ 24V DC = 0.72, 10% @ 24V DC = 2.4 41 NOTES 42