Transcript
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
SWITCHER/HIGH RESOLUTION SCALER
9.0 NOTES This product is guaranteed for 2 years from the date of purchase. If the fault in the product is due to improper use or operations carried out by third parties, the warranty is forfeited. During the warranty period, Elpro will repair the faulty units free of charge. The faulty units must be sent CARRIAGE FREE to the Elpro offices in Turin with a regular accompanying note. The units repaired will be returned CARRIAGE FORWARD to the addressee. Outside the warranty period, Elpro will repair the faulty units EX its Turin offices, charging the cost of the repair to the customer.
For any problems during installation of the MDL200, call the Elpro hot-line 011 9348778 or E-mail:
[email protected]
•
5 inputs with associated audio
•
Selectable output format
•
Maintenance of settings
•
Optional IR remote control
•
Can be controlled via RS232
MDL200-M ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
16
1
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
SWITCHER/HIGH RESOLUTION SCALER
MDL200
SWITCHER/HIGH RESOLUTION SCALER
8.0 TECHNICAL DATA
INSTALLATION AND USE THE MDL200
VIDEO: Inputs:
1.0
Overview
3
2.0
Power supply
5
3.0
Presets
5
Synch. level Vertical synch.
:N°2 Graphic (active bypass) with HDD15p.f. :N°2 CVBS (Pal, Secam, NTSC) :N°1 Y/C :High resolution with HDD15p.f. :Selectable SVGA, XGA, SXGA and HDTV 480p, 576p, 720p, 1080i :TTL :60Hz
4.0
Installation
6
Remote command
:RS232 and IR
5.0
Local control
8
6.0
Functions with IR remote control
8
7.0
Computer control via RS232
9
8.0
Technical data
15
9.0
Notes
16
INDEX:
Output Output Format
AUDIO:
Please read this handbook carefully when installing the MDL200 unit. The manufacturer does not assume any responsibility for damages caused by use, even correct, of its products.
Inputs :N°5 with RCA outlet Input coupling :AC, unbalanced Input impedance :56KΩ Input level :+9 dBm Max. Frequency response :-1 dB from 40Hz to 20KHz Crosstalk :60 dB at 5KHz Distortion :<0,03% at 0 dBm with 10KΩ load Hum & noise :-75 dBm unweighted Outputs :Unbalanced, 150Ω, with RCA outlet Balanced, 600Ω, with Phoenix screwtype
Main input :90÷240 Vac 50-60Hz Power consumption :10VA Size (WxDxH) :483x210x44
The data and characteristics of the product may vary without prior notice.
Operating temp.range Safety EMC
:0÷45° :according to EN60065 :according to EN55103-1 and-2
CE Mark
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
2
15
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
7.10.5 Setting tint The host must send the following sequence: YTXX followed by CR where YT are the pair of hex characters 59 54 XX indicates the value of tint to be set (from 00 to 48) Example: to set the value of tint to 28 the following characters must be sent on line: 59 54 32 38 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.10.6 Setting of the 3D filter The host must send the following sequence: YDX followed by CR where YD are the pair of hex characters 59 44 X indicates the status of the 3D filter (0 or 1) 0 = filter OFF 1 = filter ON Example: to activate the filter 3D the following characters must be sent on line: 59 54 31 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.10.7 Setting of noise reduction filter The host must send the following sequence: YNX followed by CR where YN are the pair of hex characters 59 4E X indicates the status of the filter Noise Reduction (0 or 1) 0 = filter OFF 1 = filter ON Example: to activate the NR filter the following characters must be sent on line: 59 4E 31 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.10.8 Setting of aspect The host must send the following sequence: YAX followed by CR where YA are the pair of hex characters 59 41 X indicates the format (0 or 1) 0 = 16:9 1 = 4:3 Example: to set the format 16:9 the following characters must be sent on line: 59 41 30 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detecte
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
14
SWITCHER/HIGH RESOLUTION SCALER
1.0 OVERVIEW Thank you for purchasing this product. Check the contents of the packaging carefully. It contains: - The MDL200 unit
- This handbook and certificate of conformity
- The mains cable
- The IR remote control (OPTIONAL)
The MDL200 transforms a video signal into a high resolution signal. Output format is selectable, from SVGA to SXGA. The Y,Cb, Cr progressive format from 480 to 1080i is also available. The output vertical frequency is set to 60Hz. The MDL200 can be used to improve image quality in the case of video-projections or display on TFT or plasma video. The wide choice of input signals each with associated audio makes the MDL200 very useful in presentation environments where several video and computer sources must be displayed on a single device.
3
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
SWITCHER/HIGH RESOLUTION SCALER
7.10.1 Setting of brightness
The audio output, which presents the associated audio of the selected input, is both unbalanced and balanced.
The host must send the following sequence: YBXX
where YB are the pair of hex characters 59 42 XX indicates the brightness value to be set (from 00 to 48) Example: to set brightness to 28 the following characters must be sent on line: 59 42 32 38 0D
For details of operation of the IR remote control, see chapter 6.0 For the data exchange protocol via RS232, refer to chapter 7.0
followed by CR
The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected. 7.10.2 Setting of contrast The host must send the following sequence: YCXX
followed by CR
where YC are the pair of hex characters 59 43 XX indicates the contrast value to be set (from 00 to 48) Example: to set contrast to 28 the following characters must be sent on line: 59 43 32 38 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.10.3 Setting of color The host must send the following sequence: YSXX
followed by CR
where YS are the pair of hex characters 59 53 XX indicates the color value to be set (from 00 to 48) Example: to set the color to 28 the following characters must be sent on line: 59 53 32 38 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected
7.10.4 Setting sharpness The host must send the following sequence: YHXX
followed by CR
where YH are the pair of hex characters 59 48 XX indicates the value of sharpness to be set (from 00 to 48) Example: to set the value of sharpness to 28 the following characters must be sent on line: 59 48 32 38 0D The MDL20000 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
4
13
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
SWITCHER/HIGH RESOLUTION SCALER
7.8 Machine status request The host must send the following sequence:
MDL200 2.0 POWER SUPPLY
The MDL200 unit must be powered with an AC voltage of 90÷240 50/60Hz using the cable provided. The outlet of the cable must be inserted in the related panel plug to the left on the back of the unit. The panel plug is equipped with a fuse-holder for 5X20 fuses. If the fuse blows, replace it with one of equal rating as specified on the back of the unit.
D followed by CR where D is the hex character 44 The MDL200 scaler replies: D hex character 44 AA number of input selected from 01 to 05 B resolution of the output from 1 to 7 CC setting of brightness from 00 to 48 DD setting of contrast from 00 to 48 EE setting of color from 00 to 48 FF setting of sharpness from 00 to 48 GG setting of tint from 00 to 48 H 3D filter 0 or 1 I NR filter 0 or 1 J format 16:9/4:3 0 or 1 L mute audio status 0 or 1 P enabling IR receiver 0 or 1 CR hex character 0D The meaning of the parameters sent by the MDL200 is the same as that of the related commands.
WARNING All operations must be carried out by qualified personnel only who must be informed of the risks of electric shock.
7.9 Firmware identifier request The host must send the following sequence: i
followed by CR
The MDL200 scaler replies:
where i is the hex character 69 i R X CR
SWITCHER/HIGH RESOLUTION SCALER
In some countries, the plug of the cable must be adapted to local standards. The wires will be identified according to the following coding:
hex character 69 MDL200 identifier (hex character 52) identifier of the firmware version (from 0 to 9) hex character 0D
- Brown PHASE (Identified with the letter L, may be red) - Blue NEUTRAL (Identified with the letter N, may be black) - Yellow/Green GROUND (Identified with the letter E, may be green)
7.10 Setting of the image adjustment parameters
WARNING A ground connection is compulsory
This category of commands includes all possible image adjustments on the High Resolution OUT, i.e. the same adjustments as permitted by the menus on OSD. This group of commands always has the Y character (hex 59) as first byte and is followed by a character that identifies the specific command.
3.0 PRESETS The MDL200 does not have hardware presets. Some firmware presets can be made directly from the keypad (see paragraph 5.3)
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
12
5
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
4.0 INSTALLATION 4.1 Video Signals Connect the composite Video sources to the 2 BNC called CV1 and CV2. The inputs are already terminated at 75 Ω; the inputs not used can be left free. Connect the Y/C source to the mini-Din connectors called Y/C. 4.2 Graphic Signals Connect the graphic sources (Notebook or computer) to the HDD15p.f. connectors called PC1 and PC2. Connect the destination (Video-projector or plasma or TFT monitors) to the HIGH RESOLUTION OUT output. WARNING If destination is a PLASMA MONITOR could be advisable to set “ON” the 3D and NOISE REDUCTION functions “on” MDL200 (OSD)
SWITCHER/HIGH RESOLUTION SCALER
7.4 Set output resolution The host must send the following sequence: fX followed by CR where f is the hex character 66 X indicates the resolution of the output (from 1 to 7) 1 format SVGA 2 format XGA 3 format SXGA 4 format 480p 5 format 576p 6 format 720p 7 format 1080i Example: to set the output format SXGA the following characters must be sent on line: 66 33 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.5 Save settings The current status of the MDL200 (i.e. the input selected, the resolution of the output, the image adjustment parameters (brightness, contrast, color, tint, sharpness), the status of the filters (3D filter and Noise Reduction filter), the output format (16:9 or 4:3) is saved in the non-volatile memory. The mute condition are not saved. The host must send the following sequence: S followed by CR where S is the hex character 53 The current settings are saved in the non-volatile memory and setat the next power-on. Example: to save the settings made the following characters must be sent on line: 53 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.6 Recall settings The host must send the following sequence: R
followed by CR
where R is the hex character 52 the setting saved previously is restored. Example: to recall the settings saved the following characters must be sent on line: 52 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.7 Restore default settings The command restores the factory settings of the parameters described above for the "Save settings" command. The host must send the following sequence: Z followed by CR where Z is the hex character 5A The factory settings are restored Example: to restore the factory settings the following characters must be sent on line: 5A 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
6
11
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
7.1 Physical connection Physical connection must be afforded using a cable according to the diagram below:
SWITCHER/HIGH RESOLUTION SCALER
4.3 Audio Signals Connect the audio of all the sources to the RCA stereo AUDIO INPUTS sockets. The MDL200 has two audio outputs: one balanced and one unbalanced. Connect the unbalanced audio output to its destination (usually a VHS recorder). Remember that level of both audio outputs cannot be regulated.
TO MDL 200
Connect the balanced audio output to a set of active speakers or to a stereo amplifier. WARNING If the speakers or the amplifier have the input unbalanced, use outputs “a” and GND leaving output “b” free. In this case, half of the output level is lost.
7.2 Video and audio input selection command The host must send the following sequence: BXX
followed by CR
where:
B is the Hex character 42 XX is the video and audio input (from 01 to 05) 01 and 02 indicates the inputs CV1, CV2 03 indicates the inputs Y/C 04 and 05 indicates the inputs PC1, PC2 Example: to select the Y/C input number 2 the following characters must be sent on line: 42 30 35 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.3 Setting mute audio The host must send the following sequence: mX
followed by CR
where m is the hex character 6D X indicates the status of the mute (0 or 1) 0 indicates mute audio de-activated 1 indicates mute audio activated Example: to activate the mute audio the following characters must be sent on line: 6D 31 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
10
7
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
SWITCHER/HIGH RESOLUTION SCALER
5.0 LOCAL CONTROL 5.1 Input selection
The following functions, divided into seven active groups, are performed with the IR remote control:
The input to be converted to high resolution is selected pressing one of the five INPUT SELECT keys. The led ON indicates which input is selected at that moment.
1st Group – 1 key: Self-teaching: Set + key CV1 Self-teaching of the remote control each time the batteries are changed. 2nd Group - 2 keys: Save and recall Save Saves all the current presets. Recall Recalls the presets saved previously with SAVE. 3rd Group - 1 key: Default DEFAULT Restores all the standard conditions of the unit.
5.2 Resolution of the output signal The resolution of the output signal can be set pressing the RESOLUTION / SELECT button repeatedly. The resolution active is indicated by the led ON and remains saved after subsequent power-on. WARNING Selecting PC1 - PC2, the format in output remains that of the PC input signal. 5.3 Presets from keypad a) Setting of the input at power-on To enable a particular input at power-on of the unit, hold down the button of that input for 3 seconds. A flash of the built-on led indicates saving of the command. From this moment on, the MDL200 will enable that input at power-on. The factory setting enables the PC1 input. b) IR reception IR reception can be disabled maintaining pressed the RESOLUTION / SELECT button during the power-on. IR reception can be re-enabled repeating the routine as above the default unit enables IR reception. 6.0 FUNCTIONS WITH IR REMOTE CONTROL The unit is equipped with a receiver for an IR remote control which must be purchased separately. WARNING The remote control is of the self-teaching type. After inserting the batteries and each time these are changed, press the "Set" key for a few moments followed by the button with violet border ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
8
4th Group - 11 keys: INPUT SELECT Press the key of the input to be converted to high resolution. The input selected is identified by switching on of the built-in led of the button located on the console. ATTENTION: ONLY TIME FIRST 5 KEYS ARE ACTIVE 5th Group - 4 keys: On Screen Display Use the 4 keys +, -, PICT and MODE to use OSD. 6th Group - 1 key: Resolution RESOLUTION Sets the format of the high resolution output signal. The format set can be viewed by checking the leds on the console of the MDL200 unit. 7th Group - 2 keys: VOLUME OUT THIS FUNCTION IS NOT AVAILABLE 8th Group - 2 keys: MICrophone THIS FUNCTION IS NOT AVAILABLE 9th Group - 10 keys: AUX DRY CONTACTS THIS FUNCTION IS NOT AVAILABLE 10th Group - 2 keys: MUTE ON-OFF THIS FUNCTION IS NOT AVAILABLE Puss MUTE ON to reset the audio level Puss MUTE OFF to restore the audio level 7.0 COMPUTER CONTROL via RS232 On its site www.elprovideolabs.com, Elpro has made available software running under Windows suitable for controlling the MDL200 via RS232. If the user intends to develop personalized software, the protocols to be implemented RS232 is available on the same site. All functions of the MDL200 can be controlled through transmission/reception by a computer of strings of hexadecimal and ASCII characters. The procedure for data exchange via RS232 is as follows: Transmission standard:
9
8 data bits, no parity, 1 stop bit and speed of 9600 baud.
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
SWITCHER/HIGH RESOLUTION SCALER
5.0 LOCAL CONTROL 5.1 Input selection
The following functions, divided into seven active groups, are performed with the IR remote control:
The input to be converted to high resolution is selected pressing one of the five INPUT SELECT keys. The led ON indicates which input is selected at that moment.
1st Group – 1 key: Self-teaching: Set + key CV1 Self-teaching of the remote control each time the batteries are changed. 2nd Group - 2 keys: Save and recall Save Saves all the current presets. Recall Recalls the presets saved previously with SAVE. 3rd Group - 1 key: Default DEFAULT Restores all the standard conditions of the unit.
5.2 Resolution of the output signal The resolution of the output signal can be set pressing the RESOLUTION / SELECT button repeatedly. The resolution active is indicated by the led ON and remains saved after subsequent power-on. WARNING Selecting PC1 - PC2, the format in output remains that of the PC input signal. 5.3 Presets from keypad a) Setting of the input at power-on To enable a particular input at power-on of the unit, hold down the button of that input for 3 seconds. A flash of the built-on led indicates saving of the command. From this moment on, the MDL200 will enable that input at power-on. The factory setting enables the PC1 input. b) IR reception IR reception can be disabled maintaining pressed the RESOLUTION / SELECT button during the power-on. IR reception can be re-enabled repeating the routine as above the default unit enables IR reception. 6.0 FUNCTIONS WITH IR REMOTE CONTROL The unit is equipped with a receiver for an IR remote control which must be purchased separately. WARNING The remote control is of the self-teaching type. After inserting the batteries and each time these are changed, press the "Set" key for a few moments followed by the button with violet border ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
8
4th Group - 11 keys: INPUT SELECT Press the key of the input to be converted to high resolution. The input selected is identified by switching on of the built-in led of the button located on the console. ATTENTION: ONLY TIME FIRST 5 KEYS ARE ACTIVE 5th Group - 4 keys: On Screen Display Use the 4 keys +, -, PICT and MODE to use OSD. 6th Group - 1 key: Resolution RESOLUTION Sets the format of the high resolution output signal. The format set can be viewed by checking the leds on the console of the MDL200 unit. 7th Group - 2 keys: VOLUME OUT THIS FUNCTION IS NOT AVAILABLE 8th Group - 2 keys: MICrophone THIS FUNCTION IS NOT AVAILABLE 9th Group - 10 keys: AUX DRY CONTACTS THIS FUNCTION IS NOT AVAILABLE 10th Group - 2 keys: MUTE ON-OFF THIS FUNCTION IS NOT AVAILABLE Puss MUTE ON to reset the audio level Puss MUTE OFF to restore the audio level 7.0 COMPUTER CONTROL via RS232 On its site www.elprovideolabs.com, Elpro has made available software running under Windows suitable for controlling the MDL200 via RS232. If the user intends to develop personalized software, the protocols to be implemented RS232 is available on the same site. All functions of the MDL200 can be controlled through transmission/reception by a computer of strings of hexadecimal and ASCII characters. The procedure for data exchange via RS232 is as follows: Transmission standard:
9
8 data bits, no parity, 1 stop bit and speed of 9600 baud.
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
7.1 Physical connection Physical connection must be afforded using a cable according to the diagram below:
SWITCHER/HIGH RESOLUTION SCALER
4.3 Audio Signals Connect the audio of all the sources to the RCA stereo AUDIO INPUTS sockets. The MDL200 has two audio outputs: one balanced and one unbalanced. Connect the unbalanced audio output to its destination (usually a VHS recorder). Remember that level of both audio outputs cannot be regulated.
TO MDL 200
Connect the balanced audio output to a set of active speakers or to a stereo amplifier. WARNING If the speakers or the amplifier have the input unbalanced, use outputs “a” and GND leaving output “b” free. In this case, half of the output level is lost.
7.2 Video and audio input selection command The host must send the following sequence: BXX
followed by CR
where:
B is the Hex character 42 XX is the video and audio input (from 01 to 05) 01 and 02 indicates the inputs CV1, CV2 03 indicates the inputs Y/C 04 and 05 indicates the inputs PC1, PC2 Example: to select the Y/C input number 2 the following characters must be sent on line: 42 30 35 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.3 Setting mute audio The host must send the following sequence: mX
followed by CR
where m is the hex character 6D X indicates the status of the mute (0 or 1) 0 indicates mute audio de-activated 1 indicates mute audio activated Example: to activate the mute audio the following characters must be sent on line: 6D 31 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
10
7
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
4.0 INSTALLATION 4.1 Video Signals Connect the composite Video sources to the 2 BNC called CV1 and CV2. The inputs are already terminated at 75 Ω; the inputs not used can be left free. Connect the Y/C source to the mini-Din connectors called Y/C. 4.2 Graphic Signals Connect the graphic sources (Notebook or computer) to the HDD15p.f. connectors called PC1 and PC2. Connect the destination (Video-projector or plasma or TFT monitors) to the HIGH RESOLUTION OUT output. WARNING If destination is a PLASMA MONITOR could be advisable to set “ON” the 3D and NOISE REDUCTION functions “on” MDL200 (OSD)
SWITCHER/HIGH RESOLUTION SCALER
7.4 Set output resolution The host must send the following sequence: fX followed by CR where f is the hex character 66 X indicates the resolution of the output (from 1 to 7) 1 format SVGA 2 format XGA 3 format SXGA 4 format 480p 5 format 576p 6 format 720p 7 format 1080i Example: to set the output format SXGA the following characters must be sent on line: 66 33 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.5 Save settings The current status of the MDL200 (i.e. the input selected, the resolution of the output, the image adjustment parameters (brightness, contrast, color, tint, sharpness), the status of the filters (3D filter and Noise Reduction filter), the output format (16:9 or 4:3) is saved in the non-volatile memory. The mute condition are not saved. The host must send the following sequence: S followed by CR where S is the hex character 53 The current settings are saved in the non-volatile memory and setat the next power-on. Example: to save the settings made the following characters must be sent on line: 53 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.6 Recall settings The host must send the following sequence: R
followed by CR
where R is the hex character 52 the setting saved previously is restored. Example: to recall the settings saved the following characters must be sent on line: 52 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.7 Restore default settings The command restores the factory settings of the parameters described above for the "Save settings" command. The host must send the following sequence: Z followed by CR where Z is the hex character 5A The factory settings are restored Example: to restore the factory settings the following characters must be sent on line: 5A 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
6
11
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
SWITCHER/HIGH RESOLUTION SCALER
7.8 Machine status request The host must send the following sequence:
MDL200 2.0 POWER SUPPLY
The MDL200 unit must be powered with an AC voltage of 90÷240 50/60Hz using the cable provided. The outlet of the cable must be inserted in the related panel plug to the left on the back of the unit. The panel plug is equipped with a fuse-holder for 5X20 fuses. If the fuse blows, replace it with one of equal rating as specified on the back of the unit.
D followed by CR where D is the hex character 44 The MDL200 scaler replies: D hex character 44 AA number of input selected from 01 to 05 B resolution of the output from 1 to 7 CC setting of brightness from 00 to 48 DD setting of contrast from 00 to 48 EE setting of color from 00 to 48 FF setting of sharpness from 00 to 48 GG setting of tint from 00 to 48 H 3D filter 0 or 1 I NR filter 0 or 1 J format 16:9/4:3 0 or 1 L mute audio status 0 or 1 P enabling IR receiver 0 or 1 CR hex character 0D The meaning of the parameters sent by the MDL200 is the same as that of the related commands.
WARNING All operations must be carried out by qualified personnel only who must be informed of the risks of electric shock.
7.9 Firmware identifier request The host must send the following sequence: i
followed by CR
The MDL200 scaler replies:
where i is the hex character 69 i R X CR
SWITCHER/HIGH RESOLUTION SCALER
In some countries, the plug of the cable must be adapted to local standards. The wires will be identified according to the following coding:
hex character 69 MDL200 identifier (hex character 52) identifier of the firmware version (from 0 to 9) hex character 0D
- Brown PHASE (Identified with the letter L, may be red) - Blue NEUTRAL (Identified with the letter N, may be black) - Yellow/Green GROUND (Identified with the letter E, may be green)
7.10 Setting of the image adjustment parameters
WARNING A ground connection is compulsory
This category of commands includes all possible image adjustments on the High Resolution OUT, i.e. the same adjustments as permitted by the menus on OSD. This group of commands always has the Y character (hex 59) as first byte and is followed by a character that identifies the specific command.
3.0 PRESETS The MDL200 does not have hardware presets. Some firmware presets can be made directly from the keypad (see paragraph 5.3)
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
12
5
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
SWITCHER/HIGH RESOLUTION SCALER
7.10.1 Setting of brightness
The audio output, which presents the associated audio of the selected input, is both unbalanced and balanced.
The host must send the following sequence: YBXX
where YB are the pair of hex characters 59 42 XX indicates the brightness value to be set (from 00 to 48) Example: to set brightness to 28 the following characters must be sent on line: 59 42 32 38 0D
For details of operation of the IR remote control, see chapter 6.0 For the data exchange protocol via RS232, refer to chapter 7.0
followed by CR
The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected. 7.10.2 Setting of contrast The host must send the following sequence: YCXX
followed by CR
where YC are the pair of hex characters 59 43 XX indicates the contrast value to be set (from 00 to 48) Example: to set contrast to 28 the following characters must be sent on line: 59 43 32 38 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.10.3 Setting of color The host must send the following sequence: YSXX
followed by CR
where YS are the pair of hex characters 59 53 XX indicates the color value to be set (from 00 to 48) Example: to set the color to 28 the following characters must be sent on line: 59 53 32 38 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected
7.10.4 Setting sharpness The host must send the following sequence: YHXX
followed by CR
where YH are the pair of hex characters 59 48 XX indicates the value of sharpness to be set (from 00 to 48) Example: to set the value of sharpness to 28 the following characters must be sent on line: 59 48 32 38 0D The MDL20000 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
4
13
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
7.10.5 Setting tint The host must send the following sequence: YTXX followed by CR where YT are the pair of hex characters 59 54 XX indicates the value of tint to be set (from 00 to 48) Example: to set the value of tint to 28 the following characters must be sent on line: 59 54 32 38 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.10.6 Setting of the 3D filter The host must send the following sequence: YDX followed by CR where YD are the pair of hex characters 59 44 X indicates the status of the 3D filter (0 or 1) 0 = filter OFF 1 = filter ON Example: to activate the filter 3D the following characters must be sent on line: 59 54 31 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.10.7 Setting of noise reduction filter The host must send the following sequence: YNX followed by CR where YN are the pair of hex characters 59 4E X indicates the status of the filter Noise Reduction (0 or 1) 0 = filter OFF 1 = filter ON Example: to activate the NR filter the following characters must be sent on line: 59 4E 31 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected 7.10.8 Setting of aspect The host must send the following sequence: YAX followed by CR where YA are the pair of hex characters 59 41 X indicates the format (0 or 1) 0 = 16:9 1 = 4:3 Example: to set the format 16:9 the following characters must be sent on line: 59 41 30 0D The MDL200 scaler replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detecte
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
14
SWITCHER/HIGH RESOLUTION SCALER
1.0 OVERVIEW Thank you for purchasing this product. Check the contents of the packaging carefully. It contains: - The MDL200 unit
- This handbook and certificate of conformity
- The mains cable
- The IR remote control (OPTIONAL)
The MDL200 transforms a video signal into a high resolution signal. Output format is selectable, from SVGA to SXGA. The Y,Cb, Cr progressive format from 480 to 1080i is also available. The output vertical frequency is set to 60Hz. The MDL200 can be used to improve image quality in the case of video-projections or display on TFT or plasma video. The wide choice of input signals each with associated audio makes the MDL200 very useful in presentation environments where several video and computer sources must be displayed on a single device.
3
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
SWITCHER/HIGH RESOLUTION SCALER
MDL200
SWITCHER/HIGH RESOLUTION SCALER
8.0 TECHNICAL DATA
INSTALLATION AND USE THE MDL200
VIDEO: Inputs:
1.0
Overview
3
2.0
Power supply
5
3.0
Presets
5
Synch. level Vertical synch.
:N°2 Graphic (active bypass) with HDD15p.f. :N°2 CVBS (Pal, Secam, NTSC) :N°1 Y/C :High resolution with HDD15p.f. :Selectable SVGA, XGA, SXGA and HDTV 480p, 576p, 720p, 1080i :TTL :60Hz
4.0
Installation
6
Remote command
:RS232 and IR
5.0
Local control
8
6.0
Functions with IR remote control
8
7.0
Computer control via RS232
9
8.0
Technical data
15
9.0
Notes
16
INDEX:
Output Output Format
AUDIO:
Please read this handbook carefully when installing the MDL200 unit.
Inputs Input coupling Input impedance Input level Frequency response Crosstalk Distortion Hum & noise Outputs
:N°5 with RCA outlet :AC, unbalanced :56KΩ :+9 dBm Max. :-1 dB from 40Hz to 20KHz :60 dB at 5KHz :<0,03% at 0 dBm with 10KΩ load :-75 dBm unweighted :Unbalanced, 150Ω, with RCA outlet Balanced, 600Ω, with Phoenix screwtype
Main input Power consumption Size (WxDxH)
:90÷240 Vac 50-60Hz :10VA :483x210x44
Operating temp.range Safety EMC
:0÷45° :according to EN60065 :according to EN55103-1 and-2
The manufacturer does not assume any responsibility for damages caused by use, even correct, of its products. The data and characteristics of the product may vary without prior notice.
CE Mark
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
2
15
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
MDL200
MDL200
SWITCHER/HIGH RESOLUTION SCALER
SWITCHER/HIGH RESOLUTION SCALER
9.0 NOTES This product is guaranteed for 2 years from the date of purchase. If the fault in the product is due to improper use or operations carried out by third parties, the warranty is forfeited. During the warranty period, Elpro will repair the faulty units free of charge. The faulty units must be sent CARRIAGE FREE to the Elpro offices in Turin with a regular accompanying note. The units repaired will be returned CARRIAGE FORWARD to the addressee. Outside the warranty period, Elpro will repair the faulty units EX its Turin offices, charging the cost of the repair to the customer.
For any problems during installation of the MDL200, call the Elpro hot-line 011 9348778 or E-mail:
[email protected]
•
5 inputs with associated audio
•
Selectable output format
•
Maintenance of settings
•
Optional IR remote control
•
Can be controlled via RS232
MDL200-M ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
16
1
ELPRO Video Labs s.r.l. Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY Tel.+39 0119348778 - FAX +39 0119348779
