Transcript
SDZ16
16x16 SD & AUDIO MATRIX
• Automatic rate selection from 143 to 360Mbit/sec • External switching reference • Switching line selectable • Command by keypad, RS232 or LAN • 16 recallable presets • Balanced audio combined SDZ16 – M 05/03/2007
ELPRO Video Labs s.r.l.
1
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
INSTALLATION AND USE OF SDZ16
INDEX 1.0
Overview
2.0
Power supply
3.0
Settings
4.0
Installation
5.0
Local control
6.0
Computer control via RS232
7.0
LAN control
8.0
Firmware upgrade
9.0
Technical data
10.0 Notes
When installing the SDZ16 unit, please read this handbook carefully. The manufacturer shall not be held responsible for any damage or injury caused by use, even correct, of its products. The data and characteristics of the product may be modified without prior notice.
ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
2
SDZ16
16x16 SD & AUDIO MATRIX
1.0 OVERVIEW Thank you for buying this product. Check the contents of the packaging carefully. It contains:
the SDZ16
the present manual and the CE certificate
the mains cable
.
SDZ16 is a SD 16x16 digital matrix with associated analog audio. The analog audio’s presence does not exclude the possibility of using SD signal’s digital audio (embedded audio). The user has the possibility to save and recall 16 configurations, via keypad and RS232. SDZ16 performs a synchronous switching with an analog external reference (genlock) with the possibility to select the switching line (2nd÷15th). (see paragraph 5.2 and 6.11).
ELPRO Video Labs s.r.l.
3
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
2 .0 POWER SUPPLY Before switching on the unit, make sure that the MAIN VOLTAGE SELECTOR corresponds to the supply voltage in your country. It is possible to choose between 120Vac and 240Vac. The panel plug is complete with fuse-holder for 5X20 fuses. If the fuse blows, replace with a fuse with the same rating as specified on the back of the unit. (T 0,5A). WARNING All operations must be carried out by qualified personnel only who must be informed of the risks of electric shock Do not remove the cover without unplugging the mains cable. In european countries, SDZ16 requires a 230 Vac 50 Hz power suppling through the mains cable. The socket of the cable must be inserted in the related panel plug on the left at the back of the unit. In some countries, the power plug must be adapted to local standards. The wires are identified according to the following coding: - Brown PHASE letter L, may be red)
(Identified with the
- Blue NEUTRAL (Identified with the letter N, may be black) - Yellow/Green GROUND (Identified with the letter E, may be green) WARNING A ground connector is mandatory
MAIN VOLTAGE SELECTOR is factory set on 240Vac. ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
4
SDZ16
16x16 SD & AUDIO MATRIX
3.0 SETTINGS SDZ16 doesn’t dispone of any internal settings by the user. Some of the functional settings are setable via keypad (see paragraph 5.2)
4.0 INSTALLATION a) Make sure that all the units to be installed are off. b) Connect the SD sources and destinations according to the screen-printed instructions on the rear panel. SD is usually a 270 Mbit/sec signal (4:2:2 component) as required by ITU-R601 normatives, or rather SMPTE 259M. However SDZ16 is able to treat also 143 Mbit/sec (4fsc NTSC), 177 Mbit/sec (4 fsc PAL) and 360 Mbit/sec (4:2:2 widescreen) signals. WARNING The Video inputs are 75 Ω terminated. It is not possible a loop in input. c) Connect the external analog reference input (usually a Black Burst) to the BNC nominated REF. If not used, close the loop with a 75Ω termination. WARNING -The presence of the REF is indicated by the letter L in the right corner of the bottom row of the display. -SDZ16 performs syncronous video input switchings to the reference signal, as its field interval. Horizontal switching line is selectable from 2nd to 15th. The advisable line is the 6th. (see paragraph 5.2 and 6.11). The switching takes places physically at the half of the line, between 25µsec. and 35µsec. If the external reference is not connected, the SD signals switch takes place anyway, but in a casual mode. d) Connect the audio sources and destinations according to the screenprinted instructions on the rear panel. ELPRO Video Labs s.r.l.
5
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
Audio inputs and outputs are balanced. If the source to connect at the input has an unbalanced output, place the hot signal at the a input of the SDZ16, connect the signal’s mass and the b input to the GND. Connect the balanced audio inputs and outputs to active speakers or to a stereo amplifier. WARNING If the speakers or the amplif ier have an unbalanced input, use the “a” outputs and the GND leaving free the "b" output In this case half of the output level will be lost.
.
WARNING: SDZ16 saves internally its own configuration, as benefit for a following switch on, 15 seconds after the last modified setting. For this reason any command sent less than 15 seconds before switching off will not be saved.
e)Supply power to the devices. The unit will predispose itself: e1) as factory configuration connecting inputs and outputs having the same number (Input 1 to output 1, input 2 to output 2 etc...). This is the case of the units first switching on. e2) as last configuration, current during the switching off. This is the regular case.
ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
6
SDZ16
16x16 SD & AUDIO MATRIX
e3) as last default configuration (see paragraph 5.2 and 6.10). Once activated, the Default configuration status will be maintained for all the successive switch ons independently of the active state before switching off. If inactivated, at switch on SDZ16 will maintain the status had at the previous switch off. At switch on, Active Default Configuration is mark ed by the “ Default Status” message that appeares for a few seconds on the right side of the display.
5.0 LOCAL CONTROL "MODE" button is used to select the functioning modality: - Only Analogic Audio Switching - Only Video Switching - SD Video+Audio Switching - LOCK, blocked keyboard
( AUDIO) ( SDI) ( BOTH) ( LOOK)
(green led on) (red led on) (both leds on) (both leds off)
TAKE, FUNCTION e CANCEL buttons are used for the matrix settings and to activate a switching command (TAKE). Matrix status is revealed on a LCD 40x2 display. On the display are indicated the sources switched on the 16 destinations numberated from 1 to 16, directly incripted on the front. Alternatively are indicated the video sources (Xpoint Video), or audio sources (Xpoint Audio) based on the setting selected using the MODE button. WARNING If 16th output is used as PREVIEW output an * (asterisk ) mark es the corresponding source on the display. (see paragraph 5.2 and 6.8) The right side of the display (8 charaters) is used for the interactivity with the user that works on the console. WARNING "Warning RPM fan" appearing on the right side of the display instead of the usual “Xpoint Video” or “Xpoint Audio” message announces a cooler fan fault so please contact Elpro assistance service.
ELPRO Video Labs s.r.l.
7
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
5.1 SWITCHING OF THE SIGNALS The video and audio outputs of the unit can be controlled using the console on the front panel. a) Press the SOURCE / DEST button to proceed with the source selection. On the right of the first display line will appear : AV or A or V in base of the function mode and S b) If the function mode is not the one desired, press MODE button until the relative writing will appear on the display c) Press one of the 16 INPUT / OUTPUT buttons to select the source. The selection will be visualized on the display. WARNING It’s possible to select more than one sources consecutively. This is extremly helpful when PREVIEW is set on the 16th output to monitorize the sources without any switching. (see paragraph 5.2 and 6.8) d) Press INPUT / OUTPUT BUTTON to abilitate the destination source. On the right side of the second display line will appear a D character : e) Press one of the 16 INPUT / OUTPUT buttons to select the destination. The selection will be visualized on the display. WARNING It’s possible to select more than one destinations consecutively without any switching. The switch will be decided pressing the TAKE button. f) Press the TAKE to effectuate the switch that will be confirmed by the visualization on the display.
ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
8
SDZ16
16x16 SD & AUDIO MATRIX
5.2 SETTINGS USING THE KEY PAD SDZ16 allows some of the settings to be operated using the keypad with the help of an LCD display. To activate settings press FUNCTION. Display shows the writing MENU with its first submenu: MENU Move using FUNCTION or 1(↑) and 9 (↓)
Recall Preset (Allows recalling previously saved presets) Confirm using TAKE Select 1......16
Confirm using TAKE and escape the MENU
Save Preset (Allows saving up to 8 presets) Confirm using TAKE Select 1......16
Confirm using TAKE and escape the MENU (Note 1)
Preview (Allows setting the 16th output as preview output) Confirm using TAKE On or Off
Move using MODE or 1(↑) and 9 (↓), confirm using TAKE and escape the MENU (Note 2)
Def. Configuration (Allows setting SDZ16 as default configuration) Confirm using TAKE On or Off
Move using MODE or 1(↑) and 9 (↓), confirm using TAKE and escape the MENU (Note 3)
Backlight (Allows setting the intensity of display’s retroillumination) Confirm using TAKE Select 1……5, Confirm using TAKE and escape the MENU
Setup Confirm using TAKE Move among following settings using FUNCTION:
Switch on _ line (Allows selecting the switching line) Select 2…….15 (Advisable line 6, fabric default) Communication: (Allows selecting the type of communication; RS232 always free running) TCP or UDP Move using MODE or 1(↑) and 9 (↓) IP-addr.: (Allows setting the IP Adress) Select using 1........10 (10 stands for 0) Move using FUNCTION among the various fields of IP-Addr. To confirm the Setup and escape the MENU, press TAKE
ELPRO Video Labs s.r.l.
9
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
WARNING To cancel any settings and escape from MENU press CANCEL for 2 seconds. Note 1: WARNING We remind you that SDZ16 allows creating and recalling presets also via RS232. The presets are superimposed, so the keypad settings might cancel or substitute the RS232 settings and viceversa. Note 2: WARNING To remind that the 16th output is used as preview output an * (asterick) markes the corresponding source on the display. Note 3: WARNING This switching state of the SDZ16 becomes Default configuration for all the successive switch ons independently of the active state before switching off. When switched on, in case of an inactive function the SDZ16 will preset itself to the same status had at the previous switch off. At switch on, Active Default Configuration is marked by the “Default Status” message that appeares for a few seconds on the right side of the display.
ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
10
SDZ16
16x16 SD & AUDIO MATRIX
6.0 COMPUTER COMMAND via RS232 A software in Windows, available on Elpro’s website www.elprovideolabs.com, is able to control the SDZ16 via RS232 .If the user is interested in downloading and installing on its own PC the program it is available in the Software Download section of the mentioned site. SDZ16 must be connected to a PC serial using a f./f. crossed RS232 cable as in the further instructions and the management program must be activated. If the user wants to develop his own customized software, in the following pages is described the related protocol. All the functions of the SDZ16 matrix can be controlled through transmission and reception of strings of hexadecimal and ASCII characters by a computer. Exchange via RS232 is based on the following procedure: 8 data bits transmission standard, no parity, 1 stop bit, speed of 9600 baud.
6.1 THE PHYSICAL CONNECTION The physical connection must be performed with a cable as described in the following plan: -SDZ16 side is a sub-D9p.f. where: pin 2 RX; pin 3 TX; pin 5 GND -the Host side is a sub-D9p.f. where: pin 2 RX ; pin3 TX; pin 5 GND
TO SDZ16
ELPRO Video Labs s.r.l.
11
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
6.2 VIDEO AND AUDIO SWITCHING COMMANDS The host must send the following sequence: B XXYY followed by CR where: B is the character Hex 42 XX is the output (from 01 to 16) YY is the video and audio input (from 01 to 16) WARNING if YY is 00 the video output will be set to high impedance the audio output will be set to 0 Volt Example: To switch video and audio input 5 on output 11, the following characters must be sent on line: 42 31 31 30 35 0D
A video input and an audio input coming from different sources can be rotated towards a video and audio output. The sequence of the characters becomes: B XXY Y
ZZ followed by CR where: B is the character Hex 42 XX is the output (from 01 to 16) YY is the video input (from 01 to 16) ZZ is the audio input (from 01 to 16)
WARNING if YY is 00 the video output will be set to high impedance If ZZ is 00 the audio output will be set to 0 Volt Example: To switch the video of input 10 and the audio of input the following characters must be sent on line: 42 30 34 31 30 30 33 0D
3
on
output
4,
The SDZ16 matrix replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected
ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
12
SDZ16
16x16 SD & AUDIO MATRIX
6.3 VIDEO SWITCHING COMMAND The host must send the following sequence: VXXYY followed by CR
where: V is the character Hex 56 XX is the output (from 01 to 08) YY is the video input (from 01 to 08)
WARNING if YY is 00 the video output will be set to high impedance Example: To bring video output 15 to high impedance, the following characters must be sent on line: 56 31 35 3030 0D
The SDZ16 matrix replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected
6.4 AUDIO SWITCHING COMMAND The host must send the following sequence: AXXYY
followed by CR
where: A is the character Hex 41 XX is the output (from 01 to 16) YY is the audio input (from 01 to 16)
WARNING if YY is 00 the audio output will be set to 0 Volt Example: To bring audio output 14 to 0 Volt, the following characters must be sent on line: 41 31 34 30 30 0D
The SDZ16 matrix replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected
ELPRO Video Labs s.r.l.
13
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
6.5 STATUS REQUEST The host must send the following sequence: D followed by CR
where: D is the character Hex 44
The SDZ16 matrix replies: D (Hex 44) followed by: -N° 32 couples of Hex characters each one representing the video or audio input switched on the output (Each input is represented by 1 couple of ASCII characters). -N° 8 hex characters hex representing: a) The preset that is active in that moment b) The fact that the 16 output is used or not as preview c) The state of the cooler fan’s well functioning d) Mute state on Audio and Video previews e) Default configuration state f) The selected switching line
2 Hex characters 1 Hex character 1 Hex character 1 Hex character 1 Hex character 2 Hex characters
-N° 1 closing character : CR Here is the replies detail: YY Video input present on bus 1 (from 01 to 16) (Example, the 3032 couple in this position means that the Video input 2 is switched on the output 1)
ZZ Audio input present on bus 1 (from 01 to 16) YY Video input present on bus 2 (from 01 to 16) ZZ Audio input present on bus 2 (from 01 to 16) (Example, the 3132 couple in this position means that the audio input 12 is switched on the output 2)
Etc… YY Video input present on bus 15 ZZ Audio input present on bus 15 YY Video input present on bus 16 ZZ Audio input present on bus 16
(from 01 to 16) (from 01 to 16) (from 01 to 16) (from 01 to 16)
CR ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
14
SDZ16
16x16 SD & AUDIO MATRIX
WARNING If the matrix replies 00 (or 30 30 on line), this means that that output is at high impedance in the case of the video and at 0 Volts in the case of the audio. P active preset number (from 01 to 16) WARNING If the matrix replies 00 (or 30 30 on line) this means that there is no preset activated
V 16th output used as preview (0=output 16 normaly used; 1= output 16 used as preview) F Functional state of the cooler fan (0= OK; 1= Fault) M Mute state on preview (0= Mute OFF; 1=Mute Audio; 2=Mute Video; 3= Mute Audio + Video) C Default configuration state (See paragraph 5.2 Note 3) (0= Not active; 1=Active) L Selected switching line (from 02 to 15) CR Example: A S DZ 16 with: a) A ll inputs connected to homony mous outputs b) 12th preset activated c) N ormal use of the 16th output ( no preview) d) C ooler fan in normal state of functioning ( no fault) e) A ctive A u dio and Video Mute f) I nactive Default C onfiguration g) L ine 6 selected as switching line, will reply: 44 30 31 30 31 30 32 30 32 30 33 30 33 30 34 30 34 30 35 30 35 30 36 30 36 30 37 30 37 30 38 30 38 30 39 30 39 31 30 31 30 31 31 31 31 31 32 31 32 31 33 31 33 31 34 31 34 31 35 31 35 31 36 31 36 31 32 30 30 33 30 30 36 0D
ELPRO Video Labs s.r.l.
15
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
6.6 RECALL OF A PRESET A previously stored preset can be activated. The host must send the following sequence: RNN
followed by CR
where: R is the character Hex 52 NN is the preset number (from 01 to 16)
Example: If the preset identified by the number 15 is to be recalled, the host will send the following sequence on line: 52 31 35 0D
6.7 CREATION OF A PRESET (SAVING CURRENT STATUS) The SDZ16 can create and perform up to 16 internal presets. A preset is a predefined configuration of 32 switching points, 16 video and 16 audio, saved in the memory and which can be recalled at any time. The presets are created from the current status of the matrix and are maintained in the case of a blackout. WARNING We remind you that SDZ16 allows creating and recalling presets also via keypad. The presets are superimposed, so the RS232 settings might cancel or substitute the keypad settings or viceversa. The host must send the following sequence: SNN
followed by CR
where: S is the character Hex 53 NN is the preset number (from 01 to 16)
Example: If preset 08 is to be assigned to the current state of the matrix, the host will send the following sequence on line: 53 30 38 0D
The SDZ16 matrix replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected
ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
16
SDZ16
16x16 SD & AUDIO MATRIX
6.8 SETTING PREVIEW OUTPUT The host must send the following sequence: pX
followed by CR
.
where: p is the character Hex 70 X indicates if the 16th output must be used as a preview output: 1 = 16 output is a preview output 0 = 16 output is a normal output
The SDZ16 matrix replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected Example: To set 16 output as preview output the host will send the following sequence on line: 70 31 0D
6.9 SETTING MUTE ON PREVIEW OUTPUT It is possible to set Audio Mute,Video Mute or both on the preview output. The host must send the following sequence: mX followed by CR where: m is the character Hex 6D X indica il tipo di mute per l' uscita di preview: 0 = mute OFF 1 = mute Audio analogic 2 = mute SD 3 = mute Audio analogic + SD The SDZ16 matrix replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if output 16 wasn’t already set as preview or if transmission errors have been detected Example: To set only A udio M ute on the preview output the host must send the following sequence: 6D 31 0D; to set mute on both A udio and Video preview outputs the host must send the following seq uence: 6D 33 0D
ELPRO Video Labs s.r.l.
17
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
6.10 DEFAULT CONFIGURATION SETUP Once activated the Default configuration status will be maintained for all the successive switch ons independently of the active state before switching off. If inactivated, at switch on SDZ16 will maintain the status had at the previous switch off. At switch on, Active Default Configuration is marked by the “Default Status” message that appeares for a few seconds on the right side of the display. The host must send the following sequence: CX
followed by
CR
where: C is the character Hex 43 X indicates the Default Configuration Status 0 = Inactive 1 = Active
The SDZ16 matrix replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected Example: To activate the Default C onfiguration the host must send the following sequence: 43 31 0D F rom that moment on S DZ 16 connections status will become Default C onfiguration for all succesive switch ons.
6.11 SWITCHING LINE SELECTION It is possible to send to SDZ16 a command that could allow selecting the switching line on a vertical interval. We advise to select line N° 6. The host must send the following sequence: LXX followed by CR where: L is the character Hex 4C XX indicates the switching line (from 01 to 15)
The SDZ16 matrix replies: ACK (Hex 06) if the command has been performed correctly NACK (Hex 15) if transmission errors have been detected Example: To switch to line 6 the host must send the following sequence: 4C 30 36 0D
ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
18
SDZ16
16x16 SD & AUDIO MATRIX
6.12 REQ UEST OF FIRMWARE RELEASE IDENTIFICATION The host must send the following sequence: i
followed by CR
where: i is the character Hex 69
The SDZ16 matrix replies: i (Hex 69) b byte highly identifiable unit (Hex 62, in case of SDZ16) Z byte low identifiable firmware release (from 0 to 9) CR Example: I f replied 69 62 31 that unit is a S DZ 16 ( H ex 62) and the uploaded firmware is release number 1 ( H ex 31).
7 .0 LAN CONTROL It’s possible to control the SDZ16 through LAN,using the same protocol as in case of the RS232. SDZ16 requires the optional LAN202 for the LAN control possibility. To set the LAN parameters and the SDZ16 available to the existing network, please refer to our web site and download from the Software Down Load section the application related to the Product LAN202: http://www.elprovideolabs.com/dwnload/LAN202usermanual-ita.zip for the italian version or http://www.elprovideolabs.com/dwnload/LAN202usermanual-eng.zip for the english version. The same user manual describes the procedures to follow for the creation af a virtual COM that allows connecting through LAN your PC to the SDZ16. An Elpro Management software able to set the COMs paramaters, respecting the settings of a previously created COM, is available to be installed and activated on your PC.
ELPRO Video Labs s.r.l.
19
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
8.0 FIRMWARE UPGRADE As for all the last generation Elpro products a remote firmware upgrade is available. Such is very useful as also customers that previously aquisted our products may benefit and add the new performances to their equipments. The firmware upgrade of SDZ16 is possible through the UPLOADER program, that must be downloaded from our web site www.elprovideolabs.com , Download software section – Firmware upgrade, and installed on your PC (Windows operating sistem required). For the firmware upgrade you must: -Download the .hex file from the firmware version that you want to install from the Elpro web site, Download software section – Firmware upgrade, and please save it to your PC. -Switch on the SDZ16 keeping pressed the MODE button. The upgrade condition is mentioned centered in the first display line by the ”Upgrade” message -Start UPLOADER and upgrade following the programs instructions -At the end of the upgrade restart the SDZ16
ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
20
SDZ16
16x16 SD & AUDIO MATRIX
9.0 TECHNICAL DATA 9.1 SD: Standard : From 143 to 360Mb/s, SMPTE259M, 8 or 10 bits Input coupling : AC, 75 Ω Inputs : 16, on BNC, with equalizer Equalization input : Up to 200 mt RG59B/U Reclocking : Automatic Input ret. Loss : >15 dB at 270MHz Switching : line 6 default, selectable from 2 to 15 Outputs : 16,on BNC, with reclocker Jitter : <0,2 UI Output level : 800 mV± 5% Ext. synch. Reference : Analog looping, Black Burst or generic CV
9.2 AUDIO: Input type
:Differential, AC, balanced with Phoenix screwtype removable. Input impedance :44KΩ differential; 22KΩ single ended Input level :11 dBm max Output impedance :600Ω Frequency response :-0.1 dB from 20Hz to 20KHz Distortion :<0.2% from 20Hz to 20KHz at +6dBm Crosstalk (Worst case):55dB at 16 KHz Hum & Noise :-63dBm unweighted (Worst case) Main Input :230Vac / 115Vac (Selectable) Power consumption :20VA Dimensioni (WXDXH) :483X220X132 Weight :4.9Kg Operating temp.range :0÷45° Safety :according to EN60065 EMC :according to EN55103-1 e 55103-2
ELPRO Video Labs s.r.l.
21
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
10.0 NOTES This product is warranted for 2 years from the date of purchase. If the fault in the product is dued to improper use or operations carried out by third parties, the warranty is forfeited. During the warranty period, Elpro will repair the faulty units free of charge. The faulty units must be sent CARRIAGE FREE to the Elpro offices in Turin with a regular accompanying note. The units repaired will be returned CARRIAGE FORWARD to the addressee. Outside the warranty period, Elpro will repair the faulty units EX its Turin offices, charging the cost of the repair to the customer.
For any problems during installation of the SDZ16 use the Elpro hot-line +39 011 7701583 or E-mail:
[email protected]
ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
22
SDZ16
16x16 SD & AUDIO MATRIX
YOUR NOTES
ELPRO Video Labs s.r.l.
23
Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
SDZ16
16x16 SD & AUDIO MATRIX
ELPRO Video Labs s.r.l. Strada della Pronda, 45/B 10142 TORINO – ITALY Tel.+39 0117701583 – Fax +39 011703751
24
