Emsealsweetscatalog2

Transcript

® 05800/EMS BuyLine 0339 Established 1959. In North America since 1979. January 2002 Page 1 of 4 Copyright © 2001 EMSEAL JOINT SYSTEMS LTD, All Rights Reserved ® PROJECT PHOTOS - CHECKLISTS - ARTICLES www.emseal.com FACADE AND ABUTMENT JOINTS CAD - TECH DATA - INSTALL DATA - SPECS USES: Curtainwall, New-To-Existing, Skywalks, Seismic, Masonry, Metal Panels, etc „ A binary (integrated primary plus secondary) seal „ Ideally suited to EIFS, curtainwall and metal cladding systems, as well as concrete, brick, stone, etc „ Combines factory-applied and cured silicone facing with permanently elastic acrylic-impregnated open-cell foam sealant backing „ Minor puncturing of silicone facing does not affect sealant system performance „ Back pressure maintains seal and ensures that silicone is virtually never under tension „ Supplied pre-compressed to smaller than joint size with self-adhesive on one face, material is inserted into joint and adhered to one side. It then expands to seal the joint. Addition in the field of a silicone corner bead ensures sealing between the silicone facing and substrate „ Standard sizes from 10" (8 mm) to 10" (250 mm) „ Sizes up to 3/4" (20 mm) have single convex facing „ Sizes from 1" (25 mm) and bigger have multiple bellows facing „ COLORSEAL movement capability +25%, -25% (50% total) „ SEISMIC COLORSEAL movement capability +50%, -50% (100% total) USES: Masonry Walls, New to Existing, Shadow Lines „ Long-term, high-performance seal for above-grade wall joints in concrete, brick, stone, etc. where black reveal or shadow-line effect is desired „ Permanently elastic, high-density, open-cell polyurethane foam, impregnated with water-based, polymer-modified asphalt, compressed to approximately 25% of its uncompressed dimension „ Supplied pre-compressed to smaller than joint size with additional self-adhesive on one face to aid installation. Material is inserted into the joint and adhered to one side. It then expands to seal the joint „ Sealing between the foam and substrate is achieved through a combination of the pressure-sensitive adhesive impregnation and the back pressure of the expanding foam „ Material is installed flush or near to the surface as a primary seal „ Standard sizes from 1/8" (3 mm) to 6" (150 mm) „ Movement capability is +25%, -25% (50% total) of nominal material size „ Joints in below-grade foundation walls utilize the higher-density 20H SYSTEM USES: Wall, Doors, Windows, Panels, Control Joints, etc „ An economical, high-performance expanding foam secondary sealant to fieldapplied liquid sealant „ Ideally suited to EIFS, as well as concrete, brick, stone, etc „ Consists of acrylic-impregnated open-cell foam material combined with laminations of closed-cell EVA foam in sizes over 3/8” (10 mm) „ Non-staining and compatible with a wide range of caulking materials „ Minor puncturing of caulked facing does not effect sealant system performance „ Supplied pre-compressed to smaller than joint size with self-adhesive on one face. Material is inserted into joint and adhered to one side. It then expands to seal the joint „ Sealing between the foam and substrate is achieved through a combination of the pressure-sensitive adhesive impregnation and the back pressure of the expanding foam „ Standard sizes from 1/8" (3 mm) to 6" (150 mm) „ +25%, -25% (50% total) movement - permanently elastic COLORSEAL™ & SEISMIC COLORSEAL™ 25V™ BACKERSEAL™ (GREYFLEX™ ) Figure 1: As a secondary sealant to liquid sealant with backer-rod. Figure 2: As a secondary sealant to directly-applied liquid sealant BACKERSEAL (Greyflex) BACKERSEAL (Greyflex) BACKERSEAL (Greyflex) recessed from joint-face prior to direct field-application of liquid sealant. Page 2 of 4 January 2002 Copyright © 2001 EMSEAL JOINT SYSTEMS LTD, All Rights Reserved BACKERSEAL (Greyflex) Directly applied liquid-sealant BACKERSEAL (Greyflex) as part of a hybrid sealant system with directly-applied liquid sealant. USA Toll Free: 800.526.8365 PH: 508.836.0280 FX: 508.836.0281 CANADA Toll Free: 866.436.7325 PH: 416.740.2090 FX: 416.740.0233 ® PROJECT PHOTOS - CHECKLISTS - ARTICLES www.emseal.com 05800/EMS BuyLine 0339 CAD - TECH DATA - INSTALL DATA - SPECS MIGUTAN® All EMSEAL deck and floor joint systems can be fire-rated and are ADA compliant - Contact EMSEAL. THERMAFLEX™ USES: Parking Decks, Including Top Decks, Stadiums, Treads & Risers, etc „ Durable under vehicular traffic and extreme weather conditions „ Cost-effective system for new and retrofit installations „ Double-cell & multi-cell designs ensure system integrity „ Extruded seals with perforated flanges embedded in high-strength, flexible, impact-absorbing elastomeric nosing „ Nosing material is two-part polyurethane reinforced with fiberglass and silica sand „ System becomes integral with deck as nosing material penetrates perforations and bonds to the concrete „ Cold applied nosing mortar is self-curing—requires no outside heat source „ Nosing material flows uniformly and is easily trowelled „ For terminations/transitions to vertical surfaces, non-sag additive is available for nosing material „ Santoprene seals are heat-weldable enabling provision of continuous seals through factory-fabricated transitions and terminations All EMSEAL deck and floor joint systems can be fire-rated and are ADA compliant - Contact EMSEAL. 20H SYSTEM™ USES: Poured-in-place intermediate level deck joints, perimeter joints, sidewalks, aprons, joints at utility rooms, parapets, belowgrade foundation wall joints, icefloors etc „ Economical, resilient, traffic-durable seal „ System consists of 20H foam, epoxy adhesive & topcoat „ Permanently elastic, high density, open-cell polyurethane foam, impregnated with water-based, polymer-modified asphalt, compressed to approximately 20% of its uncompressed dimension „ Supplied pre-compressed to smaller than mean joint size, installed flush with, or near to, surface into wet epoxy adhesive, the material expands to seal the joint „ Exposed top surface is treated with Topcoat flexible coating to enhance sealing and durability All EMSEAL deck and floor joint systems can be fire-rated and are ADA compliant - Contact EMSEAL. KONFLEX™ USES: Bus/Truck Ramps (For parking decks see THERMAFLEX) „ Shock absorbing and corrosion free „ Suitable for new and retrofit installations „ System consists of co-extruded Santoprene and high density polyethylene anchoring pads bolted down to clamp the flanges of a continuous Santoprene sealing gland into a adhesive setting bed „ Heat weldable sealing gland ensures continuity through factory fabricated transitions „ Flanges feature continuously extruded locking darts for proper locating of anchoring pads All EMSEAL deck and floor joint systems can be fire-rated and are ADA compliant - Contact EMSEAL. USA Toll Free: 800.526.8365 PH: 508.836.0280 FX: 508.836.0281 CANADA Toll Free: 866.436.7325 PH: 416.740.2090 FX: 416.740.0233 January 2002 Page 3 of 4 Copyright © 2001 EMSEAL JOINT SYSTEMS LTD, All Rights Reserved PARKING, PLAZA, STADIUM, ROADWAY JOINTS USES: Plaza (Podium), Decks, Split-Slab Roadways, Stadium Concourses „ Exceptional durability under vehicular traffic and extreme weather and temperature conditions „ Unique patented design incorporating side membranes which integrate with deck waterproofing system to form a continuous, completely watertight system „ Heavy-duty aluminum or steel retainer legs. Stainless steel protective cappings allow long-term maintenance access „ Continuous heat-weldable seal through transitions and terminations „ Positive interlocking design eliminates unsightly misalignment between adjoining sections „ Tees, crosses, directional changes, column details, terminations, and changes in plane are available as factory-fabricated assemblies „ Leg heights from 1" (25 mm) to 12" (305 mm) accommodate pavers, asphalt and other toppings ® PROJECT PHOTOS - CHECKLISTS - ARTICLES www.emseal.com INTERIOR FLOOR JOINTS CAD - TECH DATA - INSTALL DATA - SPECS The Migua (mig’-yoo-ah) interior movement joint line is a comprehensive range of expertly engineered and manufactured joints. Only a partial representation of the line is given here. Please contact EMSEAL for specific needs. MIGUA® SURFACE MOUNTED USES: Shopping Mall, Office, Airport, etc „ Durability, craftsmanship, and economy in a surface-mounted solution to new and retrofit applications „ Aesthetically pleasing with minimal exposed surface area „ FTN series features a raised insert for integration with carpet or other flooring „ Unique center “T” for support across larger joints „ Exceptional durability under pedestrian, light trolley traffic, and constant cleaning „ Floor-to-wall, tees, crosses, directional changes and column details available „ Heavy-duty aluminum construction All interior joint systems can be fire-rated and are ADA compliant - Contact EMSEAL. FN Surface-mounted w/fire barrier USES: Heavy-Duty Interior, Warehouse, Factory, Hospital, Casino, Airport, Convention Center, etc „ Heavy-duty extruded aluminum mechanical joints „ Exceptional durability under fork lift, pallet truck, hospital equipment, cleaning equipment and other heavy traffic „ Profiles available to handle up to 134,000 lbs gross or 13,000 lbs wheel load „ 3-way movement capability „ Positive interlocking design eliminates unsightly misalignment of joint sections „ Perforated mounting flanges for correct fixing and profile stability „ Various leg heights available for different floor-topping thicknesses MIGUTRANS® TUNNELS / FOUNDATIONS All interior joint systems can be fire-rated and are ADA compliant - Contact EMSEAL. USES: Positive-side sealing of joints in single-side forming applications, lagging walls, tunnel floors „ Integrates with the foundation waterproofing system on the POSITIVE side of the wall. Flanges are embedded in waterproofing mastic on top of the waterproofing geotextile. The tops of the flanges are covered with mastic as well and sandwiched with another layer of the waterproofing sheet „ Specially designed protruding anchors provide a mechanical bond to the concrete „ Thermoplastic-rubber sealing gland and side-flashing sheet components allow the heat-welding of watertight changes in direction, plane and transition to verticalplane expansion joint materials „ The BG SYSTEM integrates with Emseal's MIGUTAN FP 110/... system which is designed for use on free standing, accessible foundation walls and tunnel roofs or plaza (podium) decks BG SYSTEM™ Earth Lagging Concrete wall Below-grade waterproofing BG SYSTEM BG SYSTEM and waterproofing sandwich cast into positive side of foundation wall against lagging. Tunnel or foundation floor BG SYSTEM EMSEAL JOINT SYSTEMS, LTD., 23 Bridle Lane, Suite 3, Westborough, MA 01581-2603 EMSEAL CORPORATION, 84 Brydon Drive, Rexdale, ON, Canada M9W 4N6 EMSEAL standard warranties are available on request. EMSEAL reserves the right to change, modify, redesign, or withdraw any of its products without prior notice. Below-grade waterproofing Earth Santoprene® is a registered trademark of Monsanto Company licensed exclusively to Advanced Elastomer Systems. BG SYSTEM and waterproofing sandwich cast into positive side of foundation or tunnel floor. Page 4 of 4 January 2002 Copyright © 2001 EMSEAL JOINT SYSTEMS LTD, All Rights Reserved USA Toll Free: 800.526.8365 PH: 508.836.0280 FX: 508.836.0281 CANADA Toll Free: 866.436.7325 PH: 416.740.2090 FX: 416.740.0233