каталог En (pdf 438.89 Kb)

Transcript

Intelligent Addressable BMS and Networking Interfaces Single Mode Lon to Fibre Optic Adaptor CFSFL01 - Single Mode Lon to Fibre Optic Adaptor Overview Benefits The single mode Lon to fiber optic adapter (CFSFL01) allows connection the of Cooper system network (LonWorks) devices through optical fiber, and to allow both point to point or multi drop topology. • Simple to install • Easy to use • Extends Cooper panel network • Fast response Using only single mode fiber optic, the (CFSFL01) adapter allows extension of the Cooper system network LonWorks to a maximum distance of 15km with a transmission speed of up to 78Kbit/s or 1.25Mbit/s. Connection is made using SC type fibre optic connectors. In comparison with conventional twisted pair cable, the fibre optic usage in a LonWorks network has many advantages; it is reliable and fast in long distance network transmission even in difficult industrial environments (with transients, surges or electromagnetic interference etc.) without requiring any additional transient protection. Single Mode Lon to Fibre Optic Adaptor - CFSFL01 Dimensions 4mm Technical Specification 36mm 5mm 12mm Code CFSFL01 Description Single Mode Lon to Fibre Optic Adaptor Specification 90mm 115.5mm 10mm 100mm 52mm Operating Voltage 100mm 20mm 135mm 24V dc Communication Protocol LonWorks LonWorks Connectors Screw terminal block LonWorks Rate 78 Kbps / 1.25 Mbps Bit Error Rate 10e-9 Wavelength 1310nm Fiber Type Single mode fiber Fibre Diameter 9/125 micron Fibre Connector SC type (optional ST type) Link Distance 15km Environmental Operating Temperature -30°C to +70°C Humidity (Non Condensing) 20 to 90% RH Physical Dimensions (H x W x D) Typical System Architecture CFSFL01 Single-Mode Fiber Lon-Fiber ADAPTOR CFSFL01 LonWorks NODE Control Panel & Network Card Fiber Optic Star Topology Link LonWorks NODE Single-Mode Fiber Single-Mode Fiber CFSFL02 Terminals SC type connectors TXD RXD POW Lon-Fiber ADAPTOR LonWorks Single-Mode Fiber LonWorks Single-Mode Fiber LonWorks CFSFL02 Lon-Fiber ADAPTOR 1. Ensure that the power supply is switched off during installation. 2. Take care when inserting the fibre optic connector to avoid damage. Note that the "RX" connector in the local module’s port should connect to the "TX" connector in the far end module’s port and vice versa. 3. LonA connects to Net_A of the LonWorks Bus (network card), LonB connects Net_B. Mechanical Layout and Connections LonWorks Lon-Fiber ADAPTOR Installation CFSFL02 LonWorks NODE LonWorks NODE LonWorks NODE Control Panel & Network Card Control Panel & Network Card Control Panel & Network Card Fiber OUT TX Fiber IN RX TX RX GND LonA LonB DC24V Control Panel & Network Card Lon-Fiber ADAPTOR LonWorks LonWorks NODE LonWorks Fiber Optic Point to Point Link 36mm x 116 mm x 135mm + - LonWorks Fiber Optical Adaptor GND LONA LONB 10 9 8 7 6 5 4 3 2 1 + Unused Unused Unused Unused Unused GND LONA LONB Network Screen Connecttion Net_A of Network Card Net_B of Network Card Fiber Transmitting Fiber Receiving Network Screen Net_A Net_B LED Indication POW TXD RXD Power On Indication Fibre Port Transmitting Data Fibre Port Receiving Data on Flashing Flashing Power On Working Working Product Codes Code CFSFL01 Description Single Mode Lon to Fibre Optic Adaptor Descriptions represent only particulars of the goods to which they apply and do not form part of any contract. The company reserves the right to change specification without prior notification or public announcement. Cooper Lighting and Safety Ltd, Wheatley Hall Road, Doncaster, South Yorkshire, DN2 4NB. UK. T: +44 (0) 1302 303350 l F: +44 (0) 1302 303332 l E: [email protected] l W: www.cooperfire.com