Enrolling/pairing Sensors And Devices To The Base Unit

Transcript

ENROLLING/PAIRING SENSORS AND DEVICES TO THE BASE UNIT On the base unit When enrolling or pairing devices, press the enrol button on base unit till it beeps and then activate the sensors or devices within 30 seconds. Base will then sound 3 beeps for success. Note: Disconnect the base unit from router whenever enrolling sensors or devices. Sensors & devices Sensor and device list PIR Burglar sensor [PIR-2SN] Door/window contact switch MX-3DS Remote control RC-3 OUTDOOR PIR sensor PIR-OD1 Glass-break detector TX-3GS Flood detector TX-3FS Smoke detector SM-3S Temperature sensor TP-3 Wireless keypad KP-3S Wireless repeater/range extender RP-2S Wireless internal siren WS-1S Wireless solar powered external siren WS-30S Wireless home automation receiver Page 1 2 2 2 2 3 3 3 3 3 3 4 4 PIR Burglar sensor [PIR-2SN] Let’s start with the PIR or passive infrared sensor which is triggered when installed, by movement PLUS body heat within 10 metres and a 110 degree arc. To enrol: 1. 2. 3. Insert the 2 AA standard alkaline batteries provided in the sensor, Press the enrol button on the Securepro base unit for 3 seconds (it will start beeping) then press the RED test button inside sensor within 30 seconds. Base will then beep acknowledgement and then stop. On the video we will show you some further settings for sensors you have enrolled. MOUNTING Use the mounting screws or Velcro tabs. For best coverage, mount it in a corner adjacent to wall with entry points, 2-2.5m high. If using Velcro, brush the wall first. When mounting in a corner, cut Velcro into strips and stick on rear corners of sensor. BATTERIES Battery life is 5 years and you will be advised when they are near replacement. The long battery life for these sensors is because they do not flash again or activate after they see you until the area has been vacated for 3 minutes. Pet immune PIR burglar sensor [PIR-3SP] When the system is armed, this sensor will ignore animals up to 20kgs. To enrol: 1. 2. 3. Insert the 2 AAA standard alkaline batteries provided in the sensor. Press the enrol button on the Securepro base unit for 3 seconds (it will start beeping) then press the BLUE test button inside sensor within 30 seconds. Base will then beep acknowledgement and then stop. MOUNTING Mount 2.3m high. Because this sensor does not look down as much as previous sensor, height is critical. When mounting, the sensor window should be at the bottom. BATTERIES 2 AAA batteries last 3-5 years. The long battery life for these sensors is because they do not flash again or activate after they see you until the area has been vacated for 3 minutes. Door/window contact switch [MX-3DS] This sensor is made up of a transmitter and a magnet. To enrol: 1. 2. 3. Open the sensor with a small screwdriver on the side and insert the 2v lithium battery in the holder. Stick the transmitter on a door or window frame and the magnet within 1 cm of the side of transmitter with the raised arrow. Press enrol button on base unit and then move magnet away from transmitter. Base will beep for success. Remote control [RC-3] The remotes have the battery already installed. The four buttons are AWAY (ARM), ENTER (DISARM), HOME MODE and PANIC. To enrol: 1. Press enrol button on base unit then press ENTER button on remote. To operate the remote, press PANIC to trigger the alarm. Press HOME mode to arm the selected sensors you have put in HOME MODE. OUTDOOR PIR sensor [PIR-OD1] The outdoor PIR sensor is weather-proof and ignores pets up to 20kg. It has a range of up to 10m with a 100 degree arc. Only a human will activate it. To enrol: 1. Insert supplied 2 AA batteries and close sensor 2. Press the enrol button on the base unit and swipe a magnet up and down the sensors right hand side till you hear base unit’s response beep. MOUNTING Mount 2m high generally at property rear covering entry points. Glass-break detector [TX-3GS] The glass break sensor is made up of a transmitter and sensor which sticks on the glass. A heavy hit or the glass breaking will activate the alarm. To enrol: 3. 4. 5. Remove screw and open the sensor. Connect the 2 wires to small terminals and insert batteries. Press enrol button on base unit and red test button in sensor, base will beep success. Stick transmitter above window with double sided tape provided and peel of sensor paper and stick to window. Long range door/window contact [TX-3dS] Just attached transmitter to door or window frame and magnet on door or window within 1cm of sensor and near arrow. Just use double side tape provided To enrol: 1. 2. Remove screw and open the sensor. Insert batteries, press enrol button on base till it beeps and within 30 seconds, press test button in sensor. Flood detector [TX-3FS] The flood detector is made up of a transmitter and water sensor. The transmitter sticks to a surface above expected wet area and the sensor close to expected wet area. To enrol: 3. 4. 5. Remove screw and open the sensor. Connect the 2 wires to small terminals and insert batteries. Press enrol button on base unit and red test button in sensor, base will beep success. Smoke detector [SM-3S] The photoelectric smoke detector is installed anywhere in the premises where it will give you the earliest fire warning. To set up: 1. 2. 3. Loosen the locking screw will a small Philips screw driver, twist the bottom half to open. Insert the 9V battery and close up. To enrol, press the enrol button on base unit and square test button on front of sensor, base unit will beep success. Temperature sensor [TP-3] You can install the temperature sensor anywhere you need to be alerted if the temperature moves out of a high or low set range (for example, a freezer or a wine cellar). Set the temperature range on Living Pattern. Click ‘TP-3 sensor’ on the list of devices you have enrolled. To enrol: 1. 2. Insert the battery. Press enrol button on base unit and red test button in sensor, base unit will beep for success. Wireless keypad [KP-3S] Place the keypad near any entry. If there are sensors near the keypad, use Living Pattern website to set an Entry/Exit delay time. Go to ‘Userguides’ and download accessory manuals for more info. To enrol: 1. 2. Insert batteries in keypad. Press enrol button on base unit and enter 0 0 0 0 and the button under the 9. Base unit will beep success. Wireless repeater/range extender [RP-2S] This will add approximately 200m to the range of any sensor or accessory if it is too far away to communicate to the base unit. You can use up to 10 accessories via the range extender. Position the range extender in the area of these units. Included are a 12v/240v adapter and a built in backup battery. To enrol: 1. 2. 3. Press the enrol button on base unit. Switch on range extender and base will beep success. To add any accessory, press the button on the extender and it will flash a number of times if you have other sensors enrolled to tell you how many, then trigger the sensor or accessory the same way you did when you enrolled them to the base unit. Wireless internal siren [WS-1S] Although the base unit has an internal siren you can connect extra wireless sirens to a power point anywhere in the premises. It also has a back-up battery built in. To enrol: 1. Turn on the siren switch and on Living Pattern click Siren image. The base will beep for success. Wireless solar powered external siren [WS-30S] The solar powered 100 decibel siren and blue strobe can be mounted anywhere to receive direct sunlight on the solar panel for 10-15 hours per week. Battery life is 40 days without sunshine. The mounting bracket has a tamper switch so don’t the remove bracket with the switch on. The connections are for pre-charging. Please ignore these as the device is precharged for you. To enrol: 1. 2. 3. 4. 5. Enrol siren to base by holding enrol button till it beeps Turn on the siren switch and swipe a magnet along bottom RH side. Siren chirps. Now turn off siren for a minute or two, turn on and click Siren omage on living pattern Try to do this within 30 seconds. Turn off siren, remove bracket and fix to wall. Turn on siren before you mount it. Wireless home automation receiver You can enrol up to unlimited number of these devices to turn on lamps and appliances via the smartphone app or by a sensor or remote when triggered. To enrol: 1, Plug into power point and turn on. Press the On/Off button for 5 Sec. 2, Click Control at bottom of app and select a switch on list. Just click ON Working with Living Pattern The living pattern app will give you complete control of your security system. Not only can you arm disarm etc. but you may check past events, change all settings, name sensors and accessories etc. So.. after pairing/enrolling sensors, connect base unit to router and reboot router. Wait a few minutes then activate an accessory, eg. Press test/enroll button inside a sensor. This activation connects system to LivingPattern. Just download the app and use the username and password emailed to you. You will then see in the app all the accessories you have paired/enrolled. On this page below you can arm, disarm, select home mode (only selected sensors on) and clear events button. For example, if you have an external solar siren it will slowly flash to warn you when you get home that there has been an event. The siren button is to occasionally test siren and also for initial setup of internal or external siren. Camera button is where you can add your own camera. A 30 second clip will be recorded on remote server if system is activated and of course you can check out premises anytime. Config is to change base unit settings, see next image. Here is where you may change base unit settings. Set entry/exit delays (Later you must choose sensor/s you want to delay) Set wireless siren duration, 60 seconds default from factory. Here is where you enter up to 5 email addresses for all notifications. No need to enter SMS numbers as anyone downloading the App will receive messages to their smartphone from Living Pattern server. Click on the ‘Name’ and give the sensor a name, eg. Lounge, office etc. Click and select camera to record if this sensor is triggered. Click Config. To change sensor settings. By clicking Config. On any burglar sensor, you have all the following settings to choose from… Bypass. Ignore sensor Delay activation. Set time IE 30 seconds on base unit settings. This is usually for a sensor at entry where you may have our Wireless keypad 24 hour zone. Sensor always on. Guard in Home mode. When you click Home mode on app, 4 button remote or keypad, only sensors in home mode are armed, usually at night. Alarm with beep/relay. Base beeps before alarm Bell in disarm. Base will beep when someone walks past this sensor. By clicking on Control at bottom of screen you can bring up the home automation feature. These buttons control the wireless receiver included in the two larger packages. Just plug in lamps or appliances to the receiver. All you do to set up is connect the wireless receiver to a power point, press its ON/OFF button for 5 seconds then press any on/off button on App screen. Note. Control as many receivers as you wish. DOWNLOAD THE APP Download the app now to get complete control of your security system. Available now on Securepro BASE UNIT Specs. The Blue LED flashes when there is data being sent from the base unit. Three LEDs in green, yellow and red colors represent the system operation mode and alarm/ warning status as listed in the following table. State DISARM LED HOME AWAY DISARM with Warning Message DISARM with Alarm Message DISARM with Warning & Alarm Message HOME with Warning Message HOME with Alarm Message HOME or AWAY with Warning & Alarm Message AWAY with Warning Message AWAY with Alarm Message Red OFF Yellow OFF Green Flash OFF Flash OFF Flash OFF ON OFF OFF Flash ON ON OFF ON ON Flash ON OFF ON ON Flash ON ON OFF Flash Flash OFF OFF OFF OFF OFF Connections 1. Micro USB: 2. Tamper sensor: for tamper detection (Only for wall mounting bracket.) 3. Automation control: RJ-9 connector for X-10 control interface. (No longer available, we now use wireless automation receivers) 4. 3 wire sensor input terminals. (connect your own hardwired sensors) 5. Wire siren output terminals. 6. Aux output: for Arm/Disarm indication (driver LED indicator) 7. Power Socket: 7V DC power input. 8. SIM Card slot: Only available on our 3G security system 9. RJ-45 Ethernet Socket: Connect via Ethernet cable supplied to your router. 10. Clear/Enroll Button: Clear LED Status: Press the button for about 0.2 sec. to clear the alarm and warning LED status. Specifications Input Power: 7V DC or Micro USB input. Standby Current: About 280mA RF : (Follows local regulations, other frequencies as requested) Receiving Frequency: 915MHz Transmission Frequency: 915.MHz Data Modulation: OOK (On Off Key). Power: less than 10mW. Range: 200m to 300m or more @open field, 25℃ (Depends on sensors and Hardware version). Receiver Type: super heterodyne. RF Security Code: 16,777,216 combinations with check sum for each type of sensors. More than 4 billion combinations in total. Communication Link: Ethernet interface. Event Log: max. 512 records. Display: 4 LEDs (Away/Home/Disarm/Data). Sensor Zones: total 288 zones. (Burglar zones x 128, Fire zones x 64, Controller zones x 32, Medical zones x 32, Special sensor zones x 32) Power: NiMH rechargeable battery, back-up time 6 hours. Delay Activation Time: 0- 255 seconds programmable. Digital Interfaces : micro USB socket. Internet Interface: RJ45 Automation Switch control: RJ11 6-pin Control of 16 units X-10 switches or ( 8 XRM-01) Relay Modules. Internal siren for Alarm warning. Internet CMS protocol: Proprietary Scientech Protocol (ST-I, ST-II), CSV and SIA ADM-CID (2007) IP Alarm protocol. Wire Sensor Input: x3 can be assigned as Panic, Burglar, Fire, Medical, Tamper or Controller. Alarm Out: Open collector transistor output for 5V external siren or other alarm device. Clock Accuracy: within 5 seconds daily. Operation Temp.: -10℃~40℃. Storage Temp.: -20℃~55℃. Humidity: 10-95%RH. Size: 118x78x32 mm.(Main body) Weight: about 108 g. (Main body)