Transcript
EOS MINI / EOS MINI WIFI The Lumishore Color Change system takes the concept of marine underwater lighting installations to new levels of brightness, color and underwater experience. The innovative EOS Mini / EOS Mini WiFi allows the boat owner to achieve unrivalled levels of color options and lighting modes over the full color spectrum. The Color Controller allows you to choose and easily adjust your light color, and by scrolling through the various inbuilt lighting modes, you can select from a number of predefined colors, color cycle sequences. The Controller also incorporates fish attraction modes with variable strobe rates to enhance your fishing trip or sea life observation requirements. Color cycles and color sweeps bring dynamic moving light scenes to the boat. The EOS Mini WiFi controller has built in WiFi. This allows you to control your lights from your iPhone or iPad using the Lumishore App, which mimics the controller on you mobile device. For the ultimate party boat, The EOS Mini Controller has built in sound to light capabilities. The lights can be setup to synchronise their color change with the beat and frequency of your favourite music. Note: Refer to the relevant light installation instructions for how to install the lights onto your boat, and how to connect the system together.
PN: 45 – 0050 v 1.1
1.0 EOS MINI / EOS MINI WIFI COLOUR CHANGE CONTROLLER INSTALLATION EOS CONTROLLER COMPONENTS:
Mounting Nuts
EOS Mini / EOS Mini WiFi Colour Controller
Protective Sun Cover
Mounting Bracket
1.1 EOS MINI / EOS MINI WIFI MECHANICAL INSTALLATION The Color Controller has been designed to be mounted inside or outside within the cockpit or dash board of the vessel.
Clearance of 123mm required behind panel Choose correct size bolt for
Screw Bracket in place using supplied bolts Choose correct size bolt for
Cut through holes as required for thicker panels
Installation Considerations: Select a suitable flat surface that is accessible from behind. Ensure there are no obstructions and there is adequate clearance behind the surface to allow for the Colour Controller cable entry and positioning. (Ensure the chosen position also has easy cable routing to the first Lumi-Hub in the series) Installation Procedure: 1. Cut the hole to the correct size (60mm diameter), and ensure there is enough clearance behind the mounting panel for the controller to fit into (123mm clearance required). NB: Extreme care should be taken to cut the hole to the correct size. Always cut a smaller hole than necessary and file outwards until it is the correct size. 2.
Feed the Colour Controller through the hole and then using the clamp provided lock in place. Place the nuts onto the threaded bar, and tighten. Do not exceed 1Nm torque force on each nut.
3.
For thicker panels the mounting bracket can be shortened using the guide holes as cut points.
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
2
For external installations or where water may access the unit it is recommended that an appropriate marine sealant be used between the back of the Controller and the surface.
1.2 EOS MINI / EOS MINI WIFI ELECTRICAL INSTALLATION The controller uses a form of DMX to communicate between the lights and controller (RDMX - 2 way DMX). The Color Controller is plugged into the first Lumi-Hub in the series. The installation is terminated using a DMX Terminator plugged into the last Lumi-Hub in the series refer to the SMX 92 – SMX 152 installation manuals for further information.
The EOS controller is for 12/24volt DC operation. Under no circumstances should the Controller be connected directly to Mains AC voltage. Always use a suitable fuse or circuit breaker to protect the complete system.
Connecting the 3 pin data cables
Using the supplied DMX cable connect one end to the 3 pin pig tail connector on the back of the controller. Connect the other end to the “data in” port of the Lumi-Hub.
If using more Use a DMX extension cable to link the next Lumi-Hub. Do not cut or extend the DMX link cable. Pre-molded Extension cables are available in 1 meter, 5 meter and 15 meter lengths as required. Multiple extensions cables can be combined together if a further distance is required.
Plug the supplied DMX terminator into the last Lumi-Hub.
Always ensure the DMX Terminator is used and securely in place, without the terminator environmental noise and interference can cause faults in the communication. For full electrical installation guide please refer to the SMX 92 / SMX 152 installation manual. COMBI CABLE: - POWER CONNECTION / SOUND TO LIGHT / 3rd PARTY DMX CONTROLLER The EOS Controller is provided with a universal 3 way Combi-Cable. The Combi-Cable provides connection for power, sound to light and a 3rd party DMX controller.
POWER CONNECTION Cable Colour Key
Function
Red Black External (3rd party) DMX Input Green Blue White
Controller Power V+ Controller Power V-
3 Way Data Out Connector Power / External DMX connections
DMX + DMX DMX Ground Sound to Light 3.5mm Stereo Jack
Power to the controller is fed via the Red and Black wires. Care should be taken to ensure the correct voltage and correct polarity.
Red +V (10 to 30volt DC) Black –V (Ground) Max Current Draw @12Volts = 300mA
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
3
SOUND TO LIGHT CONNECTION A 3.5mm Jack Socket is supplied as part of the combi cable. Use a “Jack to Jack cable” or “Jack to Phono cable” as required to plug the “Line out” from a stereo or Ipad/Iphone. For best results use a stereo output that has constant output irrespective of volume. i.e When using an iPad or iPhone use the line out rather than the headphone socket. That way the sensitivity of the controller will not need continuous adjustment when changing volume. 3rd PARTY DMX CONTROLLER (OPTIONAL) A 3rd Party DMX controller can be used to control the lights in place of the EOS controller. The DMX connection wires are provided as part of the Combi-cable. (See above table for the colour key.) Do not connect the external DMX wires to anything other than an external DMX module. If an external DMX module is not used then the DMX wires should be cut back and insulated to prevent a short circuit on the wires.
EOS MINI / EOS MINI WIFI Overview and Basic Operation
2.0
Back Button (Return to previous page)
Power Button (Standby Power)
Up / Down Arrow Keys (Change settings, e.g. speed or intensity. Hold for 2 seconds for quick change to settings)
Left / Right Arrow Keys (Navigate through menus) Select Button (Press to select an option. Press and HOLD for 2 seconds to enter an adjust settings screen)
The EOS controller interface is very easy to use, use the arrow keys to navigate around menus, use the bottom middle button to select the function desired. Pressing the back button at any point will return to the previous mode or screen.
·
Power/Standby Button – Press once to turn the Controller ON. Note: The lights will not turn on until a mode is selected. Press again to turn controller and lights OFF (Standby mode).
·
Back button – press the back button to return to the previous mode or page.
·
Select Button – press the select button to enable the desired function, or to enter a menu (hold for 2 seconds to enter an adjustment menu, for example to change settings Favorites, or Sound to Light)
·
Left / Right Arrow Keys – move through the menus
·
Up / Down Arrow Keys – Adjust settings (press and hold for 2 seconds to speed up adjustment)
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
4
NOTE : When in standby mode power to the system will still be active until power is disconnected using a master switch or circuit breaker. See installation guide for the correct way to install the system. SUNCOVER: A Suncover is provided to protect the controller from harmful UV rays from the Sun and general weathering and also protects the device from accidental operation. Always ensure the Suncover is in place when the controller is not in use. 3.0 Initial Light Set Up
The Initial Light Setup tells the controller what position the lights are installed on the vessel so that they can be sent information in the correct order and color change in the correct sequence. Setting up the lights with their correct position ensures modes such as “Color Sweep” function correctly. Set up is very straightforward and will only take a short amount of time. Once setup is complete the system will memorise the light positions so this process only needs to be carried out once. To set up the lights use the following steps and the example positions shown below. The diagram shows typical positions of installed lights for three scenarios.
NOTE: In each installation, Position number 1 should be the furthest light forward on the Starboard side. At each stage note the number of each light in accordance with these schematics.
Example Positions Transom Only
Position 3
Position 2
Position 1
Example Positions for 5 lights
Position 1
Position 5
Position 4
Position 3
Position 2
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
5
Entering Light setup mode on the EOS controller: Step 1
Step 2
Step 3
Switch the controller on and scroll through using the left / right arrows until you reach Options. Press the select button.
Select Light setup Mode. Make sure all lights have power before starting the discovery. Press the select button to start the discovery process.
The controller will detect how many lights are connected and then display the result on the screen.
Step 4
Step 5
1
5
The number of lights detected by the controller will be shown once the discovery is complete. Check that the number of lights detected matches the number of lights installed. Press the select button to continue.
4 3
2
The first light detected will then start to flash a color sequence of “Blue, Green, Red”. Note: The position of the light is not yet assigned so it may be at any installation point on the vessel.
Use the up / down buttons to adjust the position of the light to the desired number. Use the right button to move to the next light.
Step 6
Step 7
1
5 4
3
2
The next light will start to flash a color sequence of “Blue , Green and Red”
Use the up / down arrow to change the light position of this light to match its position on the vessel.
Once each light has had a position allocated press the Select button to save the settings.
Repeat these steps until all lights have been assigned the correct position.
Light Setup is now Complete!
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
6
4.0
Using the Controller Menus
Use the right and left arrows to move between the main menu screens. Press the Select button to make your selection. Use the up / down arrows to adjust any settings required. 4.1 Preset Color Mode Using the left or right arrow button, scroll through the stored colors, selecting a preset color will turn all lights to that color. ·
Presets available: Blue, Green, Red, White, Cyan, Magenta, Sky and Lime
The centre of the icon will change become highlighted to indicate that this mode is currently active. 4.2 Color Cycle Mode All Lights cycle through the selected color modes; · Spectrum – Full Color Spectrum · Ice blues – Whites, Blues and Greens · Sunset – Reds and Ambers · Miami – Blues and Reds Press the select button to start the cycle, use the up and down arrows to adjust the speed of cycle.
4.3 Color Sweep Mode Individual lights will sweep through the selected spectrum creating dynamic moving lighting effects. Choose from: · Ice blues – Whites, Blues and Greens · Sunset – Reds and Ambers · Miami – Blues and Reds Press the select button to start the sweep, use the up and down arrows to adjust the speed of sweep.
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
7
4.4 Favourites Up to 6 favourite colors can be “fine tuned” and stored by the controller for future selection. Use the right / left arrows to move through the different favourite colors. Press the Select button to switch the color on. Press and HOLD the select button for 2 seconds to enter the adjustment screens where the Red, Green, Blue and White color
balance can be adjusted and saved. Use the left / right arrows to change the color to adjust. Use the up / down arrows to adjust the brightness of the color. Note: Press and HOLD the up / down arrows for 2 seconds for quick adjustment
4.5 Strobe Mode All lights will flash with the selected color. Preset Strobe colors available: Blue, Green, Red and White. The strobe can be set to a fixed or random frequency, use the left / right arrows to select. Adjustments to speed can be made whilst the light is operating using the up and down arrows. Selecting the RGB option allows you to set a custom custom strobe color. Pressing the select button for 2 seconds will open a new page where the Red, Green, Blue or White color balance can be adjusted. Save the color by pressing the select button once changes are complete. The Controller will remember this color for future use. Use the left / right arrows to change the color to adjust. Use the up / down arrows to adjust the brightness of the color. Note: Press and HOLD the up / down arrows for 2 seconds for quick adjustment
4.6 WIFI Mode Find the WiFi screen on the main menu and press the select button. The WiFi will take a few seconds to activate and connect. A box will appear around the WiFi when the system is active. Using wifi mode allows you to control your lights using an iPhone, or iPad via the Lumishore App, or by using a third party DMX software such as “Luminair” or “Alcorn McBride inc LightingPad” Note: For this mode to function the iPhone or iPad will need to be set up first. See section iPad / iPhone setup. The inbuilt wifi will only function when wifi mode is activated, returning from this menu and selecting another mode will switch the inbuilt wifi off.
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
8
4.7 External DMX Mode (Professional Installers only) Using External DMX mode hands over all control to a third party DMX device. In this mode the controller acts as a pass through DMX device and does not interfere with the DMX data. To regain control , exit this mode using the back button. External DMX can also be used with the EOS controller in standby mode. However if the controller is switched on and another function other than External DMX is selected then the controller will take precedence and regain control. For wiring installation of the third party DMX device see section 1.2
4.8 Sound to Light Mode The EOS controller has built in sound to light capabilities. The lights can be setup to synchronise their color change with the beat and frequency of the music. The controller splits the audio input into low, mid and high frequencies. The color for these frequency bands can be selected and changed. For best effect choose a different color for each frequency band. Press the select button to activate the Sound to Light mode. Hold down the select button for 2 seconds to enter the adjust settings menu, which allows you to change the colour bands, and back ground color of the Sound to Light function. Adjust the sensitivity slider to compensate for variation in volume of the input music. Choose a low sensitivity for quieter music and a high sensitivity for louder music. This sensitivity will affect the response of the lights, set it to a level that obtains the desired effect. Note, if the input music is supplied by a stereo that does not a have a fixed line level output then the sound to light sensitivity will be dependent on music volume. If little or no lighting effect is observed ensure the volume of the stereo is turned up to a high enough level.
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
9
5.0
5.0 Options Menu Selecting Options will open a further Sub-menu which allows the user to adjust some of the controller settings
5.1 Global Intensity This allows the brightness level of ALL lights to be adjusted to the desired level
5.2 WiFi Setup This screen allows the user to view or change the network name (SSID) for the controller Wifi and also set the Wifi password key. It also allows you to switch to a different WiFi channel, which may be useful in a busy marina. Note: The default SSID is “LUMISDMX”, this is the network name that will appear on your mobile device. The default Key is : 12345678. We recommend that both be changed during set-up to keep your lighting network secure. The SSID and password key will be required to configure the wireless network within an iPhone or iPad device. To configure the iPhone / iPad refer to the next section.
5.3 Display Settings The screen colours can be changed from normal (Black text on white background) to inverse (White text on black background) by pressing the select button
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
10
6.0 EOS MINI WIFI - iPhone / iPad Pairing To control the lights using an iPhone or iPad the device first has to be configured to link with the EOS Mini WiFi. This setup only needs to be carried out once per device. The following guide shows how to pair the controller with an iPhone device. (The same procedure applies for an iPad.)
Step 1
Step 2
Make a note of the SSID name and password KEY in the WIFI setup Mode in setup. The default settings are: SSID: LUMISDMX Network Key: 12345678 Note: The SSID is the network name that will appear on the WiFi list on your phone. We recommend that you change the SSID and Network key to improve the security of the system.
Once the information has been recorded return to home page and select WIFI mode. The internal wifi will be activated. Note: exiting this mode will turn the Wifi off again and the controller will not be found by the iPhone.
Step 4
Tap the blue “I” symbol to show more settings
Step 3
Next, using your iPhone search for local wifi networks. Select the SSID name for the controller and enter the password.
Step 5
Tap on ‘DHCP’ IP address. The IP address, subnet mask and router settings should be as shown above. Ensure that the DNS setting is the same as the Router setting. Once complete tap the wifi icon at the top left of the screen. Note: This procedure is for iOS 8 and above
Step 6
Launch the Lumishore App on your phone to wirelessly control your lights Note: The iPhone can take up to 60 seconds to connect with the EOS controller at which time the Wi-Fi signal strength icon will be shown in the top left hand corner of the display. iPhone Pairing is now complete!
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
11
7.0 EOS MINI WIFI - APP
Use your phone to control your lights to their full capability with the new, four channel, control EOS App from Lumishore. The Lumishore EOS App is designed for iPad and iPhone control of the Lumishore EOS Color change system installed on boats with Lumishore EOS Color controllers (with WiFi option). The App gives full control over the installed Lumishore EOS Color-change lighting system including preset Color selection, customer-defined Color mixes using the Lumishore Color wheel, preset Color cycles and stunning light sweep sequences to suit the boat owner’s every mood. When the EOS system has been connected to a music source it will also enable remote control of the Lumishore in-built sound-to-light entertainment system for that perfect party experience.
The Lumishore App gives you control of your Lumishore EOS Color-change system wherever you are on your boat, from the dock and even in your tender.
EOS App Operates with: Compatible with:
EOS mini WiFi iPhone, iPad, iPod touch (requires wireless connection) iOS 6 or later App Store / iTunes
iOS versions supported Download from:
Functions Manufacturer Preset Colors Customisable Favourites Color Cycle Fixed Strobe Mode (Any Color) Cycle Speed Adjust Random Strobe Mode (Any Color) Color Sweep Customisable Strobe Mode Color Sweep Speed Adjust Sound to Light Global Intensity Adjustment External DMX select Note: The Lumishore App will be available for download from Jan 2016
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
12
8.0 Product Support and Warranty
If you have questions or comments, please e-mail
[email protected] or call USA (941) 405-3302, United Kingdom +44(0)208 144 1694, or France +33(0)493 582 537. LUMISHORE Ltd warrants the EOS Controller to be free from defects in workmanship and materials for a period of two years, starting from the date of original purchase. Misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters such as fire, flood, and lightning, installation by unqualified personnel, unauthorized repair or modification will void this warranty. For the avoidance of confusion and doubt, non-compliance with all installation, maintenance and operating instructions in this document constitute non-conformance with warranty terms. Full warranty details are available at www.lumishore.com
Lumishore UK Unit 3, Technium 1, Kings Road, Swansea, SA1 8PH, UK | +44(0)208 144 1694 |
[email protected] www.Lumishore.com Lumishore USA 7137 24TH Court East Sarasota, Florida 34234 | (941) 405-3302 |
[email protected]
13
