Transcript
TDS
EPISOL PU TOPCOAT WB Wear resistant polyurethane top coat
USAGE
PROCESSING
Water based polyurethane top coat for epoxy and polyurethane synthetic resin floors. High scratch and fade resistance.
• Preparing the application surface Make sure the surface is clean. The recommended processing temperature for the surface, the surroundings and the material is 15 to 25°C. Do not use below 10°C and it should be at least 3°C higher than the dew point temperature.
CHEMICAL RESISTANCE Maximum relative humidity is 80%. Good chemical resistance to alkalis, petroleum derivatives, acid, diluted organic acids, salts and solutions. Low resistance against tannines, anti-oxidants and plasticizers. Stains made by these products will become darker by UV. For more information please contact RESIPLAST NV.
PROPERTIES
EPISOL PU TOPCOAT WB is applied to a cured system. Polyurethane and epoxy synthetic resin floors that are older than 2 days must be roughened. Resin floors of unknown composition can only be coated once an adhesion test has been carried out and the results of this test are positive.
• Mixing Stir the base (component A) evenly before use. Add the full amount of hardener (component B) and mix mechanically (300 rev/min) until both components are homogeneous.
• Water based • Very high UV resistance • High wear and scratch resistance • Low consumption • Smooth surface • Low dirt build-up
• Application Apply EPISOL PU TOPCOAT WB with a lint-free roller using a paint bucket or paint roller tray. Spread crosswise using firm pressure. Finish off after 15 minutes with a broad paint roller working crosswise. The last paint strokes should always be in the same direction to avoid structural differences. Make sure there is adequate ventilation and low humidity during the curing process. Replace the paint rollers after 45 minutes. A second coat must be applied after 24 hours.
• Use EPISOL PU TOPCOAT WB can be mechanically loaded after 72 hours. Make sure there is adequate ventilation. Complete chemical resistance after 7 days at 20°C, lower temperatures will extend the curing time.
Resiplast NV/SA • Gulkenrodestraat 3 • B-2160 Wommelgem •
[email protected] • www.resiplast.be Tel.+32 3 320 02 11 • Fax+32 3 322 63 80
PACKAGING
USAGE
EPISOL PU TOPCOAT WB
Comp A
Comp B
4,5kg
0,575
Set 5,075kg
TECHNICAL SPECIFICATIONS
100g/m² per layer
APPEARANCE Component A
Polyurethane dispersion
Component B
Aliphatic hardener
Specific mass
1.04kg/dm³
Colour
Transparent
Viscosity
55Mpa.s
Layer thickness
80 – 100µm
• Paint roller and paint roller tray
Adhesion
>2.6N/mm²
• Cleaning solvent for tools: MEK SOLVENT
Surface
Smooth
Pot life
90 min
Hardness Shore D
80 – 90
Min. application temperature Hardening temperature
+10°C +10°C
Hardening time at 20°C
Touch dry 6 h Can be mechanically loaded 72 h Can be chemically loaded 7 days
YOU WILL NEED TO SUPPLY
STORAGE Store EPISOL PU TOPCOAT WB in a dry, well ventilated storage area between 5 and 35°C. Six months shelf life.
Curing
Non-shrinking
Shelf life
12 months
If in doubt, contact RESIPLAST NV and provide the batch number on the package. Do not let the product get in contact with ground water, surface water or sewage systems. Dispose of contaminated packaging and remnants according to legal regulations.
SAFETY
CE CERTIFICATE
Resiplast NV, Gulkenrodestraat 3, B-2160 Wommelgem 12
Carefully read the safety instructions before using EPISOL PU TOPCOAT WB.Products have a characteristic odour when being applied. Ensure there is sufficient ventilation, stay away from ignition sources and do not smoke. Avoid contact with skin. Eye irritation and/or sensitivity may occur during heavy vapour concentrations, inhalation and/or skin contact. Do not keep food products (food, beverages) in the same workspace. Always wear personal protective equipment according to local guidelines and regulations. Gloves and safety goggles are mandatory.
EN 13813 Resin screed/coating for use indoors in buildings. Reaction to fire
NPD
Release of corrosive substances
SR
Water permeability
NPD
Abrasion resistance (Taber)
<10 mg (CS10-1000tr-1kg )
Adhesion strength
B 1,5
Impact resistance (DIN EN ISO 6272)
>10Nm
Soundproofing
NPD
Sound absorption
NPD
Thermal resistance
NPD
Chemical resistance
NPD
VOC complies with Belgium emission legislation (2012/0568/B) (EU CEN/TS 16516)
The above information is provided in good faith, but without any guarantees. The application, use and processing of the products are beyond our control and are, as such, the sole responsibility of the user/ processor. In the event that Resiplast N.V. is still held liable for damages, then the claim will still be limited to the value of the goods delivered. We always aim to deliver consistently high quality goods. This version replaces all previous versions. Version 1.3 Date: 8 June 2016 12:28 PM
Resiplast NV/SA • Gulkenrodestraat 3 • B-2160 Wommelgem •
[email protected] • www.resiplast.be Tel.+32 3 320 02 11 • Fax+32 3 322 63 80
