Epower Controller

Transcript

EPower™ MODEL • Fully software configurable • Predictive Load Management • Current rating 50A to 630A (nominal load 16A to 630A) • Voltage up to 690V ac • All types of firing modes • Measurement accuracy <1% • Large integral four row display • Remote display option • Multi-channel unit • Event Log Power management and control units Specification Sheet EPower™ is the Eurotherm® series of advanced power control units. Combining the advantages of the latest technologies and innovations to produce a truly impressive performance for your process. Ratings The EPower current ratings cover the range from 50 Amps up to 630 Amps (nominal 16 Amps to 630 Amps). Ratings are designed at 40°C, but operation can be defined up to 50°C with associated deratings. The voltage rating can go up to a maximum of 690 volts. Predictive Load Management (Patented) You can reduce your energy costs across your plant by using the Predictive Load Management functionality within EPower. This innovative feature provides a better distribution of energy across different loads in your installation by managing the priority and if necessary, load shedding. • Optional I/O • Modbus RTU comms • Profibus DP comms • DeviceNet® comms • Ethernet (Modbus TCP) comms • EtherNet/IP comms • CC-Link comms • Profinet IO comms • Voltage, current and power control • Complete diagnostics • Energy counter • Single phase Load Tap Changer Multi Channel Unit EPower includes seven different power configurations within one unit, depending on the number of power modules fitted. From single phase configuration to two times two phase control, the unit is perfectly modular and configurable to your process requirements. Multiple zones can be controlled with one unit. Many more features are available (Log file management, advanced alarm strategy, optional I/O…) to provide you with the best of the technology for your process. Display and Remote Display EPower is fitted with a 4 line x 10 character display with indication of the process values, and diagnostic information, along with an alarm and event message centre. Optionally, the EPower has a 32h8e remote display to allow for the process values and alarm information to be presented front of panel in a clear and unambiguous way. Secure access to the local setpoint is also provided to allow for local control when needed. The remote display, as an indicator, can also provide over temperature policeman functionality removing the need imagine having the power to save energy Power module Number of modules: Up to four identical units per Driver Module Voltage range: 100 to 600V ac (+10% - 15%) or 100 to 690V ac (+10% - 15%) as specified at time of order Frequency range: 47 to 63Hz Nominal current: 16 to 630A depending on power module Power dissipation: 1.3W per Amp per phase Rated short-circuit conditional current: CE Rated. 92kA all modules except: 98kA for 500A modules; 105kA for 630A modules. Note: this is not a UL508A test Cooling Up to and including 100A: Natural convection Above 100A: Fan cooling. Fans are connected in parallel to driver module connector Fan supply voltage: 115 or 230V ac, as specified at time of order (see ‘Caution’ above) Fan power requirement: 10W for 160A/250A modules; 15W for 400A, 500 and 630A modules Protection Thyristor drive: RC circuits and high-speed fuses Pollution degree: Pollution degree 2 (EN60947-1) Installation category Power network: Installation category III up to 600V; Installation category II up to 690V Auxiliary (fan) supply: Installation category II assuming nominal phase voltage with respect to earth is ≤300V rms Utilisation categories AC51: non inductive or slightly inductive loads, resistance furnaces AC56a: switching of transformers Duty cycle: Uninterrupted duty/continuous operation Form designation: Form 4 Short circuit protection co-ordination type: Type1 (fuses) Load types: Single or multiphase control of resistive loads (low/high temperature coefficient and non-aging/aging types) and transformer primaries. Load voltage/current feedback either internal (standard) or external (option for use with transformer secondaries for example) Communication Eurotherm has an approach to open communications, offering standard fieldbus networks such as Modbus RTU, Profibus DP, DeviceNet®, Ethernet (Modbus TCP), EtherNet/IP, CC-Link and Profinet IO communications.. The use of Fieldbus makes integration into PLCs and other supervisory systems easy to accomplish. It allows an easier integration into PLCs and other supervisory systems by using the main protocols of the market. Configuration “Quick Start” HMI menus provide an easy and friendly way to quickly configure the unit. With the more complex configurations using the iTools software package. General specification Physical Dimensions and fixing centres: See Fixing Details Weight: See Table 2 (weights ± 50gm (2oz) General Standards The product is designed and produced to comply with EN60947-4-3 (Low voltage switch gear and control gear). Other applicable standards are cited where appropriate. Weight (including 2kg (4.4lb) for driver module) Current 1 phase 2 phases 3 phases 4 phases 50A/100A 6.5 (14.3) 11.0 (24.3) 15.5 (34.2) 20.0 (44.1) 160A 6.9 (15.2) 11.8 (26.0) 16.7 (36.8) 21.6 (47.6) 250A 7.8 (17.2) 13.6 (30.0) 19.4 (42.8) 25.2 (55.6) 400A 11.8 (26.0) 21.6 (47.6) 31.4 (69.2) 41.2 (90.8 500A 14.0 (30.9) 26.0 (57.3) 38.0 (83.8) 50.0 (110.2) 630A 14.5 (32.0) 27.0 (59.5) 39.5 (87.1) 52.0 (114.6) Table 2 Weights Installation Categories General installation category details for the driver and power units are summarised in the table below. Installation Category Rated impulse withstand voltage (Uimp) Communications II 0.5kV Standard I/O II 0.5kV Driver module power II 2.5kV Relays III 4kV Power Modules (up to 600V) III 6kV Power Modules (690V) II 6kV Auxiliary (Fan) supply II 2.5kV Table 1 Installation category details Rated insulation voltage 50V 50V 230V 230V 600V 690V 230V lb oz 0.1 1.6 0.2 3.2 0.3 4.8 0.4 6.4 0.5 8.0 0.6 9.6 0.7 11.2 0.8 12.8 0.9 14.4 Environment Temperature limits Operating: 0°C to 50°C (derate above 40°C as per accompanying curves) Storage: -25°C to 70°C 630 Amp unit 600 Power (at 40°C) Maximum current (A) Humidity limits: Altitude (maximum): Protection: Atmosphere: Voltage range: 100 to 240V ac (+10% - 15%) Frequency range: 47 to 63Hz Power requirement: 60W + Power Module fans (15W each for 400A/500A/630A power modules; 10W each for 160A/250A modules) Installation Category Installation category II (category III for relays) External wiring: Shock (EN60068-2-29): Vibration (EN60068-2-6): 2 400 Amp unit 400 300 250 Amp unit 200 160 Amp unit 100 Amp unit 100 0 Driver module Eurotherm Part No. HA029669 Issue 5 June 10 500 Amp unit 500 Caution Although the driver module supply voltage range is 85 to 265V ac, the fans (if any) fitted to the power (thyristor) modules are specified for use at one of 115V ac or 230V ac as specified at time of order. Before plugging the fan harness into the driver module, ensure that the utility supply voltage is suitable for the fan(s). Otherwise, fan life may be shortened or the cooling effect may not be sufficient, either case presenting a possible hazard to the equipment or to the operator. 50 Amp unit 0 10 20 30 Temperature °C 40 50 5% to 95% RH (non-condensing) 1000 metres IP10 (EN60529) Non-explosive, non-corrosive and non-conductive Must comply with IEC 364 10g Peak; 6ms duration; 100 bumps 67-150Hz at 1g EPower Specification Sheet EMC Standard: Immunity criteria: Operator Interface Display: Character format: Push buttons: LED indicators (beacons): Analogue input: Current input performance Parameter Typical Max/Min Total current working input span -1mA to +25mA Resolution (noise free) (Note 1) 12 bits Calibration error (Notes 2 and 3) <0.25% <0.5% Linearity error (Note 2) ±0.1% Ambient temperature error (Note 2) <0.01%/°C Input resistance (+‘ve to -’ve terminal) 235Ω Input resistance (-‘ve terminal to 0V) 150Ω Allowable voltage (-‘ve terminal to 0V) <±1V Series mode rejection of mains interference 46dB >30dB Common mode dc rejection 46dB >40dB Hardware response time 5ms Note 1: w.r.t. total working span Note 2: % of effective range (0 to 20mA) Note 3: After warm up. Ambient =25°C EN60947-4-3 Emissions class A This product has been designed for environment A (Industrial). Use of this product in environment B (domestic, commercial and light industrial) may cause unwanted electromagnetic disturbances in which cases the user may be required to take adequate mitigation measures. Immunity criterion 1 (criterion 3 for voltage dips and short-time interruptions) 4 lines of up to 10 characters each. Display pages can be used to view process variable values and to view and edit the configuration of the unit. (Editing of the configuration is better carried out using configuration software (iTools). In addition to the standard displays, up to four ‘custom’ pages can be defined which allow bargraph displays, text entry etc. 7 high x 5 wide yellow-green LCD dot matrix array 4 push buttons provide page and item entry and scroll facilities 3 indicators (PWR LOC and ALM) are supplied to indicate that power is applied, that Local Control is selected and that there is one or more active alarm respectively Table 4 Analogue input specification table (current inputs) Analogue output: Voltage output performance Parameter Typical Max/Min Total voltage working span -0.5V to +12.5V (within ±20mA (typ.) current span) Short circuit current <24mA Resolution (noise free) (Note 1) 12.5 bits Calibration error (Notes 2 and 3) <0.25% <0.5% Linearity error (Note 2) <±0.1% Ambient temperature error (Note 2) <0.01%°C Minimum load resistance >800Ω DC output impedance <2Ω Hardware response time (10% to 90%) 20ms <25ms Note 1: w.r.t. total working span Note 2: % of effective range (0 to 5V, 0 to 10V) Note 3: After warm up. Ambient = 25°C Standard Inputs/Outputs (SK1) All figures are with respect to driver module 0V, unless otherwise stated. Number of inputs/outputs No of analogue inputs: 2 No of analogue outputs: 1 No of digital inputs/outputs: 2 (each configurable as an input or an output) 10V (Potentiometer) supply: 1 Update rate: Twice the mains frequency applied to power module 1. Defaults to 83.2Hz (12ms) if no power applied to power module1 or if supply frequency lies outside the range 47 to 63Hz) Termination: Removable 10-way connector. (5.08 mm. pitch) Table 5 Analogue output specification table (voltage outputs) Analogue output: Current output performance Parameter Typical Max/Min Total current working span -24mA to +24mA (within -0.3V to +12.5V voltage span) Open circuit voltage <16V Resolution (noise free) (Note 1) 12.5 bits Calibration error (Notes 2 and 3) <0.25% <0.5% Linearity error (Note 2) <±0.1% Ambient temperature error (Note 2) <0.01%°C Maximum load resistance <550Ω DC Output conductance <1μA/V Hardware response time (10% to 90%) 20ms <25ms Note 1: w.r.t. total working span Note 2: % of effective range (0 to 20mA) Note 3: After warm up. Ambient = 25°C Analogue Inputs Performance: Input types: See Tables 3 and 4 Each input is configurable as one of: 0 to 10V, 1 to 5V, 2 to 10V, 0 to 5V, 0 to 20mA, 4 to 20 mA Absolute maxima + terminal: ±16V or ±40mA - terminal: ±1.5V or ±300mA Table 6 Analogue output specification table (current outputs) 10V supply (Potentiometer supply) Output voltage: 10.0V ± 0.3V @ 5.5mA Short circuit o/p current: 15mA max. Ambient temperature drift: ± 0.012%/°C (typ); ±0.04%/°C (max.) Absolute maxima Pin 1: (-0.7V or -300mA) or (+16V or +40mA) Analogue outputs Performance: See Tables 5 and 6 Output types: Each output is configurable as one of 0 to 10V, 1 to 5V, 2 to 10V, 0 to 5V, 0 to 20mA, 4 to 20 mA Absolute maxima + terminal: (-0.7V or -300mA) or (+16V or +40mA) 0V terminal: ±2A Digital I/O Hardware response time: Voltage inputs Active level (high): Non-active level (low): Input impedance: Contact closure inputs Source current: Open contact (non active) resistance: Closed contact (active) resistance: Current source output Source current: Analogue input: Voltage input performance Parameter Typical Max/Min Total voltage working input span (Note 1) -0.25V to +12.5V Resolution (noise free) (Note 2) 13 bits Calibration error (Notes 3 and 4) <0.25% <0.5% Linearity error (Note 3) ±0.1% Ambient temperature error (Note 3) <0.01%/°C Input resistance (+‘ve terminal to 0V) >140kΩ Input resistance (-‘ve terminal to 0V) 150Ω Allowable voltage (-‘ve terminal to 0V) ±1V Series mode rejection of mains interference 46dB >30dB Common mode dc rejection 46dB >40dB Hardware response time 5ms Note 1: w.r.t. to the relevant -‘ve input Note 2: w.r.t. total working span Note 3: % of effective range (0 to 5V, 0 to 10V) Note 4: After warm up. Ambient = 25°C Open circuit voltage: Internal pull-down resistance: Absolute maxima + terminal: 0V terminal: 4.4V500Ω <150Ω 9mA1mA Voltage: >1V Contact configuration: Single pole change-over (One set of Common, Normally Open and Normally Closed contacts) Termination Relay 1 (standard): 3-way connector on underside of driver module Watchdog relay (standard): 3-way connector on underside of driver module Relays two to four (option): 12-way option module connector Installation Category Installation category III, assuming that nominal phase to earth voltage is ≤300V RMS. Isolation between different relays’ contacts is double isolation, in accordance with the installation category and phase to earth voltage specified above. Absolute max switching capability: <2A at 240V RMS (resistive loads) Load RMS voltage squared (Vsq): Thyristor RMS current squared (Isq): True load power (P): Frequency resolution: Measurement resolution: Meas. drift with ambient temp: Further parameters (S, PF, Q, Z, Iavg, IsqBurst, IsqMax, Vavg, Vsq Burst, VsqMax and PBurst) are derived from the above, for each network (if relevant). See EPower User Guide Section (Meas submenu) for further details. External Current Transformer Ratio: CC-Link Protocol: Connector: Indicators: CC-Link version 1.1 5-way RUN and ERR DeviceNet Protocol: Connector: Indicators: DeviceNet 5-way Network status and Module status EtherNet Type: Protocol: Connector: Indicators: 10baseT (IEEE801) Modbus TCP RJ45 Tx activity (green) and communications activity (yellow) EtherNet/IP Protocol: Connector: Indicators: EtherNet/IP RJ45 NS (Network status), MS (Module status) and LINK (Link status) Optional Input/Output Modules (SK3, SK4, SK5) Up to three input/output modules can be fitted, each containing the inputs and outputs detailed below. Unless otherwise stated below, the specification for the optional I/O (including relays) is as given above for the standard I/O. Number of modules: Number of inputs: Number of outputs: Number of relays: 10V potentiometer supply output voltage: Removable 12-way (5.08mm pitch) connector per module Up to 3 1 analogue input and 2 digital inputs per module 1 analogue output per module 1 set of common, normally open and normally closed contacts per module 10.0V ±0.3V at 5.5mA Modbus RTU Mains Network Measurements All network measurements are calculated over a full mains cycle, but internally updated every half-cycle. For this reason, power control, current limits and alarms all run at the mains half-cycle rate. The calculations are based on waveform samples taken at a rate of 20kHz. Measurements on each phase are synchronised to its own phase and if the line voltage cannot be detected, the measurements stop for that phase. It should be noted that, depending on the configuration, the phase voltage referred to is one of: Protocol: Transmission standard: Connector: Indicators: Isolation (EN60947-4-3): Terminals to ground: a. the line voltage referenced to neutral in four star, b. the line voltage referenced to neutral or another phase for single phase networks or c. the line voltage referenced to the phase applied to the next adjacent power module for three phase star or delta networks. Eurotherm Part No. HA029669 Issue 5 June 10 Chosen such that the full scale output from the current transformer is 5 Amps Communications Note: Normally closed and normally open refer to the relay when the coil is not energised. Termination: ±0.5% of Nominal Vline ±0.5% of Nominal V for voltage readings >1% of Nominal V. Unspecified for readings lower than 1%Vnom ±0.5% of Nominal IRMS for current readings >3.3% of Nominal IRMS Unspecified for readings = 3.3% Nominal IRMS For external current feedback the above specification does not include errors associated with external current transformers. ±1% of (Nominal V)2 ±1% of (Nominal I)2 ±1% of (Nominal V) x (Nominal I) 0.1Hz 11 bits of Nominal value (noise free) <0.02% of reading /°C 4 Modbus RTU slave 3-wire EIA485 Twin, parallel-wired RJ45 Tx activity (green) and Rx activity (yellow) Installation category II, Pollution degree 2 50V RMS or dc to ground (double isolation) Profibus Protocol: Connector: Indicators: Profibus DPV1 9-way D-type Mode and Status Profinet Protocol: Connector: Indicators: Profinet IO R J45 NS (Network status), MS (Module status) and LINK (Link status). EPower Specification Sheet Electrical Installation Front Drive Module Connectors = Polarising pin Local PWR Alarm LOC 14 LOC ALM Pushbuttons Return Scroll down Scroll up 12 View on underside EPower PWR 11 Relay 1 ALM Enter NC Power NO Beacons Com Configuration Port (EIA232) SK6 Relay 1 Mating Connector Polarising Pin Locations 04 01 02 SK6 Watchdog Relay Communications SK2 SK7 Watchdog Relay SK1 Standard I/O 1 +10 Volts out 2 Analogue i/p 1 + 3 Analogue i/p 1 – 4 Analogue i/p 2 + 5 Analogue i/p 2 – 6 Analogue o/p 1 + 7 Analogue o/p 1 0V 8 Digital i/o 1+ 9 Digital i/o 2+ 10 10 Digital i/o 0V SK3 SK4 Predictive Load SK2 Management Option 1 SK1 SK5 SK7 1 5 1 2 3 4 5 Terminator A Low Shield High Terminator B Remote display (isolated EIA485) SK8 SK8 SK9 N L NLE Supply output for power module fan(s) Supply in Mating connector (section) SK9 Polarising key (Position 3) = Polarising pin SK3 Optional I/O 1 1 +10 Volts out 1 2 Analogue i/p 3 + 3 Analogue i/p 3 – 4 Analogue o/p 2 + 5 Analogue o/p 2 0V 6 Digital i/p 3 + 7 Digital i/p 4 + 8 Digital 0V 9 Not used 10 Relay 2 NO (24) 11 Relay 2 Com (21) 12 12 Relay 2 NC (22) SK4 Optional I/O 2 1 +10 Volts out 1 2 Analogue i/p 4 + 3 Analogue i/p 4 – 4 Analogue o/p 3 + 5 Analogue o/p 3 0V 6 Digital i/p 5 + 7 Digital i/p 6 + 8 Digital 0V 9 Not used 10 Relay 3 NO (34) 11 Relay 3 Com (31) 12 12 Relay 3 NC (32) SK5 Optional I/O 3 1 +10 Volts out 2 Analogue i/p 5 + 3 Analogue i/p 5 – 4 Analogue o/p 4 + 5 Analogue o/p 4 0V 6 Digital i/p 7 + 7 Digital i/p 8 + 8 Digital 0V 9 Not used 10 Relay 4 NO (44) 11 Relay 4 Com (41) 12 12 Relay 4 NC (42) Polarising pins: Fixed connector: pins 1 and 2; Mating connector: pin 3 Polarising pins: Fixed connector: pins 2 and 3; Mating connector: pin 1 Polarising pins: Fixed connector: pins 1 and 3; Mating connector: pin 2 1 Safety Earth Details Max. load current Minimum earth cable cross-section Size 50/100A 160A 250A 400A 500A 630A 25 mm2 35 mm2 70 mm2 120 mm2 150 mm2 185 mm2 M6 M6 M8 M10 M12 M12 Earth Terminal Tightening torque 5 Nm (3.7 ft lb) 5 Nm (3.7 ft lb) 12.5 Nm (9.2 ft lb) 15 Nm (11.1ft lb) 25 Nm (18.4 ft lb) 25 Nm (18.4 ft lb) Power Module Connectors External feedback connections Load I1 current I2 Load cable exit Underneath view V1 Load Voltage V2 Neutral/phase reference (either pin) Line/Load Termination Details Max. load Terminal current size 50/100A M8 M8 160A 250A M10 M12 400A 2 x M12 500A 2 x M12 630A External Feedback Connector Pinout and Polarising Details Module 1 I2 Current external feedback connector I1 V1 Voltage external feedback connector V2 Module 2 I1 Module 3 Module 4 I1 + I2 None None I1 + I2 I2 V2 V1 + V2 None None V1 + V2 Minimum cable cross-section 35 mm2 70 mm2 120 mm2 240 mm2 2 x 150 mm2 2 x 185 mm2 Recommended torque setting 12.5 Nm (9.2 ft lb) 12.5 Nm (9.2 ft lb) 25 Nm (18.4 ft lb) 28.8 Nm (21.2 ft lb) 30 Nm (22.1 ft lb) 30 Nm (22.1 ft lb) V1 Neutral/ phase reference connector Eurotherm Part No. HA09669 Issue 5 June 10 5 EPower Specification Sheet Communications Pin 1 2 3 4 5 Modbus RTU Pinout Function V– (negative bus supply voltage) CAN_L Cable shield CAN_H V+ (positive bus supply voltage) Network Status LED Indication LED state Interpretation Off Off-line or no power Steady green On-line to 1 or more units Flashing green On-line - no connections Steady red Critical link failure 1 or more connections timed out Flashing red Network Status 1 Notes: 1. See DeviceNet specification for power supply specification 2. During startup, an LED test is performed, satisfying the DeviceNet standard. Module Status LED Indication LED state Interpretation Off No power Steady green Operating normally Flashing green Missing or incomplete configuration Steady red Unrecoverable fault(s) Flashing red Recoverable fault(s) 5 Module Status Pin Signal (EIA485) 8 Reserved 7 Reserved 6 N/C 5 N/C 4 N/C 3 Isolated 0V 2 A 1 B Internal connections: Pin 1 to 5V via 100k Pin 2 to 0V via 100k LEDs: Green = Tx activity Yellow = Rx activity Green 8 MODBUS / RTU DeviceNet Connector Pinout 1 8 1 Yellow Connectors in parallel Function N/C A (RxD–/TxD–) N/C +5 V (1) Pin 5 4 3 2 1 Function Isolated ground RTS B (RxD+/TxD+) N/C N/C Notes: 1. Isolated 5 Volts for termination purposes. Any current drawn from this terminal affects the total power consumption. 2. The cable screen should be terminated to the connector housing. Mode PROFIBUS / DP Pin 9 8 7 6 Modbus TCP (Ethernet 10baseT) Pinout 9 5 6 1 Status Operation Mode LED Indication LED state Interpretation Off Off-line or no power Steady green On-line, data exchange Flashing green On-line, clear Red single flash Parametrisation error Red double flash Profibus configuration error LED state Off Steady green Flashing green Steady red Status LED Indication Interpretation No power or not initialised Initialised Diagnostic event present Exception error Pin 8 7 6 5 4 3 2 1 Function N/C N/C Rx– N/C N/C Rx+ Tx– Tx+ LEDs: Green = Tx activity Yellow = Network activity Yellow MODBUS / TCP Profibus Connector Pinout 8 1 Green CC-Link Connector Pinout Pin Function 1 2 3 4 5 110R, 1/2W, 5% across DA (Rx+/Tx+) pins 1 and 2 of first DB (Rx–/Tx–) and last connectors DG (Signal ground) SLD (Cable Shield) SLD and FG connected internally FG (Protective Ground) Notes: 1. A 110 Ohm (±5% 1/2 watt) terminating resistor should be connected across pins 1 and 2 of the connectors at each end of the transmision line. 2. The cable shield should be connected to pin 4 of each CC-Link connector. 3. The shield and Protective earth terminals (pins 4 and 5) are internally connected. RUN 1 5 ERR LED state Off Green Red ‘RUN’ LED Indication Interpretation Off-line or no power Normal operation Major fault (fatal error) LED state Off Steady red Flickering red Flashing red ‘ERR’ LED Indication Interpretation No error or no power Exception or fatal event CRC Error Station number of Buad rate has changed since startup EtherNet/IP Connector Pinout Pin 1 2 3 4 5 6 7 8 Function Tx+ TxRx+ N/C N/C RxN/C N/C LINK LED Indication LED state Interpretation Off No Link, no activity Steady green Link established Flickering green Activity in progress NS 1 8 LINK MS NS (Network Status) LED Indication LED state Interpretation Off No power or no IP address On-line, one or more connections established (CIP class 1 or 3) Steady green Flashing green On-line, no connections enabled Steady red Duplicate IP address, (’fatal’ error) Flashing red One or more connections timed out (CIP class 1 or 3) MS (Module Status) LED Indication LED state Interpretation Off No power Steady green Controlled by a scanner in Run state Flashing green Not configuration or scanner in idle state Steady red Major fault (Exeption-state, fatal error etc.) Recoverable fault Flashing red Profinet IO Connector Pinout Function Tx+ TxRx+ N/C N/C RxN/C N/C LINK LED Indication LED state Interpretation Off No Link, no activity Steady green Link established; no activity Flickering green Activity in progress Eurotherm Part No. HA029669 Issue 5 June 10 NS PROFINET IO Pin 1 2 3 4 5 6 7 8 LINK MS LED state Off Steady green Flashing green NS (Network status) LED Interpretation No power or no connection with I/O Controller On-line (RUN); connection with IO controller estabished. Controller in ‘Run’ state On-line (STOP); connection with IO controller estabished. Controller in ‘Stop’ state LED state Off Green steady Green 1 flash Green 2 flash Red steady Red 1 flash Red 2 flash Red 3 flash Red 4 flash MS (Module status) LED Interpretation Not initialised No power or the module is in ‘SETUP’ or ‘NW_INIT’ state Normal operation The module has shifted from the ‘NW–INIT’ state Diagnostic event One or more Diagnostic Event present Blink Used by engineering tools to identify the node on the network The module is in ‘EXCEPTION’ state Exception error Configuration error The Expected Identification differs from the Real Identification IP Address error The IP address is not set Station Name error The Station Name is not set Internal error The module has encountered a major internal fault 6 EPower Specification Sheet General diagrams Caution 1. Neutral/phase reference connections (if applicable) must be located between any isolating device and the relevant Power Module. 2. For single phase configurations, all Neutral reference connections must be individually fused. Single Phase Control Phase Neutral Up to Four Single Phase Control with Independent Loads Phase 1 2 Safety and cut device 3rd phase 1 2 reference Fuse Two Phase Control with Load Coupled in Delta or Star Phase 1 2 12 12 Four independent loads Two times Two Phase Control with Loads Coupled in Delta or Star 3 12 Neutral (or other phase) 12 Fuse Phase 1 Safety and cut device 3rd phase 1 2 reference 4 Safety and cut device Single phase load Neutral 1 2 reference 3 Fuse 2 3 Safety and cut device 3rd phase 1 2 reference 12 12 Three phase load coupled in delta or star 12 Fuse Three phase load coupled in delta or star Three phase load coupled in delta or star Three Phase Control with Load Coupling in Delta or Star Phase 1 2 3 Three Phase Control with Load Coupled in Open Delta Phase 1 12 12 Three phase load coupled in delta or star Eurotherm Part No. HA09669 Issue 5 June 10 Phase 1 3 Voltage 1 2 reference 12 12 2 3 Neutral Safety and cut device Safety and cut device Safety and cut device Voltage 1 2 reference 2 Three Phase Control with Load Coupled in Star with Neutral Three Phase load coupled in open delta Voltage 1 2 reference 12 12 Fuse Load coupled in star with neutral Fuse 7 EPower Specification Sheet 50A/100A (drawing on the right) 160A/250A (drawings next page) Fixing Details 50Amps/100Amps Dimension mm (inches) Overall Widths 50/100/160/250 AMPS 1 No of phases 2 3 149.5 (5.89) 234.5 (9.23) 319.5 (12.58) Door closed 211.0 (8.31) 296.0 (11.65) 381.0 (15.00) Door open Bracket 2-phase 3-phase 4-phase Upper Use A & B Use A, B & C Use A, B, C & D Recommended fixing bolt size = M6 61.4 (2.42) 107.5 (4.232) Safety earth (M6) Recommended tightening torque = 5 Nm (3.7 ft lb) Cable entry 21.5 (0.85) 85.0 (3.346) 85.0 (3.346) 85.0 (3.346) A B C 4 404.5 (15.93) 466.0 (18.35) D 42.0 (1.65) Insert 5 (1/4 in) screwdriver here, and pull down to release door EPower 330 (12.99) 317 (12.48) Note: Units are shown with individual mounting brackets. Multi-phase units come supplied with 2, 3 or 4 phase brackets as appropriate. See table below for details. 6.5 (0.26) FRONT VIEW Door (Open) Lower Use E & F Use E, F & G Use E, F G & H E F G H Cable exit/entry 194.4 (7.65) 252.2 (9.93) Communications VIEW ON UNDERSIDE 400A (drawing on the right) 500A/630A (drawing next page) Fixing Details Note: Units are shown with individual mounting brackets. Multi-phase units come supplied with 2, 3 or 4 phase brackets as appropriate. See table below for details. Dimension mm (inches) 400Amps 8.5 (0.33) FRONT VIEW Line cable entry 25 (0.98) Recommended fixing bolt size = M8 127.5 (5.02) 125 (4.921) A 125 (4.921) B 62 (2.44) 125 (4.921) C D Safety earth (M10) Recommended tightening torque = 15 Nm (11.1 ft lb) Bracket 2-phase 3-phase 4-phase 1 2 189.5 (7.46) 314.5 (12.38) 251.0 (9.88) 376.0 (14.80) Upper Use A & B Use A, B & C Use A, B, C & D 3 439.5 (17.30) 501.0 (19.72) 4 564.5 (22.22) 626.0 (24.65) 474.5 (18.681) Overall Widths 489.5 (19.28) EPower 400/500/630AMPS No of phases Door closed Door open Lower Use E & F Use E, F & G Use E, F G & H Door (Open) Communications E F G H Cable exit/entry 208.4 (8.20) 252.2 (9.93) Load cable entry 10 (0.39) E L N L N VIEW ON UNDERSIDE Eurotherm Part No. HA029669 Issue 5 June 10 8 EPower Specification Sheet 160Amps 250Amps Safety earth (M6) Recommended tightening torque = 5 Nm (3.7 ft lb) 85.0 (3.346) 85.0 (3.346) 85.0 (3.346) A B C D 42.0 (1.65) Insert 5 (1/4 in) screwdriver here, and pull down to release door 361 (14.21) 348 (13.70) EPower Recommended fixing bolt size = M6 61.4 (2.42) 107.5 (4.232) Safety earth (M8) Recommended tightening torque = 12.5 Nm (9.2 ft lb) B C EPower D 42.0 (1.65) Insert 5 (1/4 in) screwdriver here, and pull down to release door Door (Open) Door (Open) C L Communications E F G Communications H C L VIEW ON UNDERSIDE F G H Cable exit/entry 194.4 (7.65) Cable exit/entry 194.4 (7.65) 252.2 (9.93) E 252.2 (9.93) Cable entry 21.5 (0.85) 85.0 (3.346) 85.0 (3.346) 85.0 (3.346) A 388 (15.28) 107.5 (4.232) 6.5 (0.26) Cable entry 21.5 (0.85) Recommended fixing bolt size = M6 61.4 (2.42) FRONT VIEW 401 (15.79) 6.5 (0.26) FRONT VIEW VIEW ON UNDERSIDE 8.5 (0.33) 500Amps/630Amps Line cable entry 30 (1.18) FRONT VIEW Line cable entry 68 (2.68) Recommended fixing bolt size = M8 127.5 (5.02) 125 (4.921) A 125 (4.921) B 62 (2.44) 125 (4.921) C D A EPower 474.5 (18.681) 489.5 (19.27) Safety earth (M12) Recommended tightening torque = 25 Nm (18.4 ft lb) Door (Open) Communications F G Load cable entry 25 (0.98) Load cable entry 63 (2.48) H E L N L N Cable exit/entry 212 (8.35) 296 (11.65) E VIEW ON UNDERSIDE Eurotherm Part No. HA09669 Issue 5 June 10 9 EPower Specification Sheet Order codes 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 EPOWER The code is divided in three sections: 1 Hardware, which defines the type, number and size of the unit and/or the modules. 2 Optional hardware and software functions. 3 QuickStart which is intend to configure the unit for maximum 60 to 80% of the application (single unit in 1, 2 or 3 legs configuration) The code can then be either “Short” and include only the main hardware fields or “medium” and combine the hardware + the optional fields, or finally “Long” with the additional quick start code at the end. Basic Product Power Controller EPOWER 1 Phase/Amps 1PH-50A 1PH-100A 1PH-160A 1PH-250A 1PH-400A 1PH-500A 1PH-630A 2PH-50A 2PH-100A 2PH-160A 2PH-250A 2PH-400A 2PH-500A 2PH-630A 3PH-50A 3PH-100A 3PH-160A 3PH-250A 3PH-400A 3PH-2500A 3PH-630A 4PH-50A 4PH-100A 4PH-160A 4PH-250A 4PH-400A 4PH-500A 4PH-630A PWR-50A PWR-100A PWR-160A PWR-250A PWR-400A PWR-500A PWR-630A DRV-XXX 1 Phase unit 50A 1 Phase unit 100A 1 Phase unit 160A 1 Phase unit 250A 1 Phase unit 400A 1 Phase unit 500A 1 Phase unit 630A 2 Phase unit 50A 2 Phase unit 100A 2 Phase unit 160A 2 Phase unit 250A 2 Phase unit 400A 2 Phase unit 500A 2 Phase unit 630A 3 Phase unit 50A 3 Phase unit 100A 3 Phase unit 160A 3 Phase unit 250A 3 Phase unit 400A 3 Phase unit 250A 3 Phase unit 630A 4 Phase unit 50A 4 Phase unit 100A 4 Phase unit 160A 4 Phase unit 250A 4 Phase unit 400A 4 Phase unit 500A 4 Phase unit 630A 50A Power module 100A Power module 160A Power module 250A Power module 400A Power module 500A Power module 630A Power module Driver module only 4 Warranty XXX WL005 USWL3 Internal Use 5 XXX 6 XXX XXX PLM None Predictive Load Management XX XF None - Standard unit External feedback* * Factory option None 14 Remote Panel 7 Option None - End of Code Unit with options and/ or quick start definition XX 00 8 No optional fieldbus communication 2-wire 485 Modbus (RJ45 connector) Profibus-DPV1 (with D type connector) Modbus-TCP DeviceNet Ethernet/IP CC-Link Profinet IO Y2 PB ET DN IP CC PN 9 XX 32ENG 32FRA 32GER 32ITA 32SPA None 32h8e English 32h8e French 32h8e German 32h8e Italian 32h8e Spanish Communications Protocol XX Module 1 None IO optional board 100V to 600V 100V to 690V For Driver mod only 10 Module 2 XX IO None IO optional board 230V ac ≥160A 115V ac ≥160A No fan ≤100A 11 Module 3 XX IO Eurotherm Part No. HA029669 Issue 5 June 10 None IO optional board Language ENG FRA GER ITA SPA English French German Italian Spanish 20 Load Current (nominal) 16A 25A 40A 50A 63A 80A 100A 125A 160A 200A 250A 315A 400A 500A 630A 16 Amps 25 Amps 40 Amps 50 Amps 63 Amps 80 Amps 100 Amps 125 Amps (Note 1) 160 Amps (Note 1) 200 Amps (Note 1) 250 Amps (Note 1) 315 Amps (Note 1) 400 Amps (Note 1) 500 Amps (Note 1) 630 Amps (Note 1) 15 Software Option 1 XXX EMS LTC None Energy Measurement (Counter) Load Tap Changer 16 Software Option 2 XXX EMS LTC None Energy Measurement (Counter) Load Tap Changer 17 Not Used XX Default Fan Supply 230V 115V XXX 19 13 External Feedback Voltage 600V 690V XXX 3 None Internal Use XX IO 2 Standard 5 Year US Extended 12 Predictive Load Management 18 Quick Start XX QS 10 None - End of code Quick Start config 21 Load Voltage (nominal) 100V 110V 115V 120V 127V 200V 208V 220V 230V 240V 277V 380V 400V 415V 440V 460V 480V 500V 575V 600V 660V 690V 100 Volts 110 Volts 115 Volts 120 Volts 127 Volts 200 Volts 208 Volts 220 Volts 230 Volts 240 Volts 277 Volts 380 Volts 400 Volts 415 Volts 440 Volts 460 Volts 480 Volts 500 Volts 575 Volts 600 Volts 660 Volts (Note 2) 690 Volts (Note 2) EPower Specification Sheet 22 Control Type (Note 3) Single phase Two phase control Three phase control 1P 2P 3P 23 Load Configuration (Note 4) Single phase Star Delta Star with neutral Open delta 1P 3S 3D 4S 6D 24 Load Type Resistive Transformer primary XX TR 25 Firing Mode (Note 5) Phase angle Half cycle Burst firing (default 16 cycles) Fix modulation period (default 2 seconds) Logic mode PA HC BF FX LG 28 Analogue Input 1 Function 33 Analogue Output Type (Note 6) XX SP HR IL VL PL TS Configuration XX 0V 1V 2V 5V 0A 4A None Setpoint Setpoint limit Current limit Voltage limit Power limit Current transfer span 29 Analogue Input 1 Type XX 1V 2V 5V 0A 4A None 0-10 Volt 1-5 Volt 2-10 Volt 0-5 Volt 0-20 mA 4-20 mA XX SH I1 I2 RI DC DI 34 Digital Input 2 Function None 1-5 Volt 2-10 Volt 0-5 Volt 0-20 mA 4-20 mA XX AK RS None Alarm acknowledgement Remote setpoint selection RD Control None – Load Management disabled Sharing Incremental Type 1 Incremental Type 2 Rotating Incremental Distributed Control Distributed Control and Incremental Control Rotating Distributed and Incremental Control 37 Predictive Load Management Address 35 Alarm Relay Configuration XX AA PA FB 30 Analogue Input 2 Function (Note 6) XX SP HR IL VL PL TS 36 Load Management None Setpoint Setpoint limit Current limit Voltage limit Power limit Current transfer span None Any alarm Process alarms Fuse blown XX Predictive Load Management address (00 to 63) Default address 00 SPARE FUSE FOR POWER MODULES 26 Feedback RMS load voltage squared RMS load current squared True power RMS load voltage RMS load current Open loop V2 I2 TP VR IR OL 27 Current Transfer Mode (Linear Current Limit) (Note 6) XXX I2 IR Off RMS load current squared transfer RMS load current transfer Eurotherm Part No. HA09669 Issue 5 June 10 Current rating amps 50A 100A 160A 250A 400A 500A 630A 31 Analogue Input 2 Type XX 0V 1V 2V 5V 0A 4A None 0-10 Volt 1-5 Volt 2-10 Volt 0-5 Volt 0-20 mA 4-20 mA Notes 1. The maximum nominal current selectable is the current rating selected in Field 1. 2. Only available if 690V selected in Field 2. 3. Selection dependent on number of Phases selected in Field 1. 1PH = IP only 2PH = IP or 2P only 3PH = IP or 3P only 4PH = IP or 2P only 4. Selection dependent on number of Phases selected in Field 1. 1PH = 1P only 2PH = 1P, 3S or 3D only 3PH = Any 4PH = 1P, 3S or 3D only If IP selected in Field 22 only option is IP. 5. PA not selectable if 2P selected in Field 22. HC not selectable if TR selected in Field 24. 6. Except XX the selection in Fields 28 and 30 cannot be the same. 32 Analogue Output Function XX X V I P R Fuse number CS179139U315 CS179139U315 CS179139U315 CS179139U350 CS179439U630 CS029859U630 CS029960U900 None None Voltage Current Power Impedance 11 EPower Specification Sheet 32h8e EPower Remote Panel Mechanical Details 96 (3.78) 90 (3.54) 48 (1.89) Panel cut-out 45 (1.77) (–0.0 +0.6) x 92 (3.62) (–0.0 +0.8) 10 (0.39) Model number 32h8e is a horizontal 1/8DIN indicator and alarm unit that performs the dual function of remote display for EPower and independent ‘policeman’. The latter is intended to disconnect should an overtemperature (or other excess process condition) occur. 32h8e communicates with EPower using Modbus protocol via the EIA485 RJ45 connector located on the underside of the EPower controller. Dimension mm (inches) 38 (1.50) Recommended minimum spacing The remote panel is normally ordered as an option with EPower units. It is a fixed hardware build consisting of a relay output in OP1 and an analogue output in OP3. There are no user communications since this is used to communicate with EPower and the supply is high voltage only (100-240Vac). The unit is configured using ‘QuickStart’ code on initial start up. If more than one unit is mounted in the same panel they should be spaced to allow sufficient air flow between them. Rear Terminals 100 to 240V ac 50/60Hz Neutral Line The 32h8e is based on a 32h8i indicator and has the same and additional features as this instrument. For features not covered please refer to HA029005. Dig in B Output 3 (OP3) PV Retransmission V/mA Output 1 (OP1) Changeover Relay N L 3D 3C 3B 3A LC LB 2B 2A 1B 1A V– V+ VI LA C CT HF HE HD AC AB AA The 32h8e displays EPower Current, Voltage, Power and Setpoint parameters for each EPower Network. The Setpoint of the EPower networks can be adjusted via the 32h8e HMI. Indication of selected setpoint is included: local or remote. Wire sizes The screw terminals accept wire sizes from 0.5 to 1.5mm (16 to 22AWG). Hinged covers prevent hands or metal making accidental contact with live wires. The rear screws should be tightened to 0.4Nm (3.3lb in). ! T/C Ensure that the supply to the unit does not exceed 240V ac +10% mA mV/V Example Wiring Diagram – + Sensor Pt100 Input B (–) A (+) COM Digital Comms Dig in A 2.49 N * General notes about relays and Inductive Loads L1 L2 L3 Coil Auxiliary circuit fuse Contactor * 32h8e Fuse L N N L 3D 3C 3B 3A LC LB 2B 2A 1B 1A EPower Driver V- – V+ VI LA C CT HF HE HD AC AB AA + Furnace Temperature T/C EPower Power U nit RJ45 connector Screen EPower Power U nit EPower Power U nit When switching inductive loads such as contactors or solenoid valves, wire the 22nF/100 ‘snubber’ supplied across normally open relay terminals. This will prolong contact life and reduce interference. ! Snubbers pass 0.6mA at 110V and 1.2mA at 230V ac, which may sufficient to hold on high impedance loads. Local ground Eurotherm Part No. HA029669 Issue 5 June 10 12 EPower Specification Sheet Cold junction accuracy: Linear (process) input range: Thermocouple types: Specification - 32h8e Remote display General Environmental performance Temperature limits Operation: Storage: Humidity limits Operation: Storage: Panel sealing: Shock: Vibration: Altitude: Atmospheres: Resistance thermometer types: Bulb current: Lead compensation: Input filter: Zero offset: User calibration: 0 to 55°C -10 to 70°C 5 to 85% RH non condensing 5 to 85% RH non condensing IP65, Nema 4X BS EN61010 2g peak, 10 to 150Hz <2000 metres Not suitable for use in explosive or corrosive atmosphere <±1°C at 25°C ambient –10 to 80mV, 0 to 10V K, J, N, R, S, B, L, T, C, custom download (Note 2) 3-wire Pt100 DIN 43760 0.2mA No error for 22 ohms in all leads Off to 100s User adjustable over full range 2-point gain & offset Notes (1) Calibration accuracy quoted over full ambient operating range and for all input linearisation types (2) Contact Eurotherm for details of availability of custom downloads for alternative sensors Electromagnetic compatibility (EMC) Emissions and immunity: BS EN61326 OP 1 Electrical safety (BS EN61010): Type: Rating: Installation cat. II; Pollution degree 2 INSTALLATION CATEGORY II The rate impulse voltage for equipment on nominal 230V mains is 2500V. Functions: OP 3 POLLUTION DEGREE 2 Normally, only non-conductive pollution occurs. Occasionally, however, a temporary conductivity caused by condensation shall be expected Physical Panel mounting: Dimensions and weight: Panel cut-out dimensions: 1/8 DIN, horizontal 96mm (3.78”) W x 48mm (1.89”) H x 90mm (3.54 inches) D, 350g (0.77lbs) 92mm (1.77 inches W x 45mm (3.62 inches) H Operator interface Type: Main PV display: Lower display: Status beacons: LCD TN with backlight 5 digits, green or red 9 character starburst, green Units, outputs, alarms Power requirements Voltage: Frequency: 100 to 240V ac, –15%, +10%, max 9W 48 to 62Hz Form C (changeover) Min 100mA @12V dc, max 2A@240V ac resistive Alarms, events Isolation: Functions: Current output 264V ac double insulated Retransmission Rating: 0-20mA into <500Ω Accuracy: ±(<0.25% of Reading + <50μA) Resolution: 13.6 bits Voltage output Resolution: Rating: 0-10V into >500Ω Accuracy: ±(<0.25% of Reading +<25mV) 13.6 bits Software features Alarms Number: Type: 4 Absolute high & low, Rate of change (rising or falling) Latching: Auto or manual latching, non-latching, event only Output assignment: Up to four conditions can be assigned to one output EPower Alarms: Missing mains, Thyristor short circuit, Open thyristor, Fuse blown, Over temperature, Voltage dips, Frequency fault, Power module 24V fault, Total load failure, Chop off, Partial Load Failure, Partial Load Unbalance, Volt fault, Temperature pre alarm, Power module wdog fault, Power module comms error, Power module timeout, Closed loop, Output fault The pre-set alarms have a fixed medium priority enables indicator alarms to be configured as lower, the same or higher priority. EPower alarms can be globally acknowledged via the 32h8e HMI. Approvals CE, cUL listed (file E57766) Communications Serial communications option Protocol: Modbus RTU Master Isolation: 264V ac, double insulated Transmission standard: EIA485 (2 wire) The 32h8e has Modbus Master RS485 Comms with a fixed set of EPower Modbus addresses. Power up the display for the first time, configure the QuickStart code for the standard indicator functions, and the process values and alarm messages are immediately displayed, automatically configured to match the EPower display - for example RMS values or average values for current, voltage and power displayed as 3 phase or as several times single phase as defined by the EPower configuration. Other status outputs Functions: Output assignment: 32h8e Terminal RJ45 Pin Number HD White/Green Common 3 HE Orange Rx A(+) 2 HF White/Orange Tx B(-) 1 Custom messages Number: No of characters: Languages: Selection: Process variable input Calibration accuracy: Sample rate: Isolation: <±0.25% of reading ±1LSD (Note 1) 9Hz(110ms) 264V ac double insulation from the PSU and communication Resolution (μV): <0.5μV with 1.6s filter (mV range) <0.25mV with 1.6s filter (Volts range) Resolution (effective bits): >17 bits Linearisation accuracy: < 0.1% of reading Drift with temperature: <50ppm (typical) <100ppm (worst case) Common mode rejection: 48-62Hz, >-120db Series mode rejection: 48-62Hz, >-93dB Input impedance: 100MΩ (200KΩ on volts range C) Cold junction compensation: >30/1 rejection of ambient change External cold junction: Reference of 0°C Eurotherm Part No. HA03296695 Issue 5 June 10 Recipes Number: Selection: Other features Display colour: Scrolling text: Display filter: Peak monitor: 13 Including sensor break, power fail, new alarm, pre-alarm Up to four conditions can be assigned to one output 15 scrolling text messages 127 characters per message max English, German, French, Spanish, Italian Active on any parameter status using conditional command 5 recipes with 19 parameters HMI interface, communications or digital IO Upper display selectable green or red or change on alarm Parameter help, custom messages Off to zero last 2 digits Stores high and low values EPower Specification Sheet 32h8e Initial configuration At first switch on, after the start-up sequence, the initial configuration page is displayed. Note: the following ‘quickstart’ description apples only to new (not previously configured) instruments. If the instrument has previously been configured (either at the factory or subsequently) the instruments starts up showing the relevant process value. 32h8 The initial display shows ‘Set1’ on the top line, with a coded display below with its first item flashing. The lower line is decoded as shown in table. The ‘mode’ (up/down arrows) are used to scroll through the available choices for each item. Once the required value is displayed, the scroll key is used to select the next character for editing. Once all five characters have been edited, further operations of the scroll key call the range high display (allowing the high range Set1 Display value to be edited usingthe mode keys), then the range low display (allowing the low range value to be edited). A further operation calls the Set2 display, which is decoded in the table below. Input type Display units B J K L N R S T C P M 2 4 0 3 6 C F K * P 0 1 2 3 4 5 6 7 8 9 Type B T/C Type J T/C Type K T/C Type L T/C Type N T/C Type R T/C Type S T/C Type T T/C Custom T/C Pt100 RTD Linear 0 to 80 mV Linear 0 to 20 mA Linear 4 to 20 mA Linear 0 to 10V dc Linear 2 to 10V dc Linear 0 to 5V dc Degrees Celsius Degrees Fahrenheit Kelvins None % Pa (Pascals) mPa (milli Pascals) kPa (kilo Pascals) Bar mBar PSI kg/cm mmWG inWG mmHg A B D E G H J L M R T U W Y Z After Set2 parameters have been edited, a further operation of the scroll key invites the user to Exit. Operating the scroll key returns to the Set1 display; operating a mode key to display ‘yes’ quits the quickstart menuand causes the unit to enter operating mode. Eurotherm: AUSTRALIA Sydney T (+61 2) 9838 0099 E [email protected] AUSTRIA Vienna T (+43 1) 7987601 E [email protected] BELGIUM & LUXEMBOURG Moha T (+32) 85 274080 E [email protected] BRAZIL Campinas-SP T (+5519) 3707 5333 E [email protected] CHINA T (+86 21) 61451188 E [email protected] Beijing Office T (+86 10) 5909 5700 E [email protected] Display top line (PV) colour Home display 0 1 2 3 4 G R C N A 1 2 I V P nnnnn nnnn.n nnn.nn nn.nnn n.nnnn Green Red Red in alarm, else green PV only First alarm setpoint (SP) only PV + Alarm SP (Read/Write) PV + Alarm SP (Read only) Current (see note) Voltage (see note) Power (see note) Note: The default display for I, V and P is network 1. The ‘page’ key isused to access the parameter for other networks. Page key Scroll key Mode keys Set2 parameter coding Relay output (OP1) Analogue output (OP3) x H L R N O P 7 8 9 A B C E F G x 1 2 3 4 5 6 Not configured High alarm only Low alarm only Rate of change (ROC) alarm only New alarm Sensor break only After power fail only High alarm or sensor break Low alarm or sensor break ROC alarm or sensor break High alarm or after power fail Low alarm or after power fail ROC alarm or after power fail High alarm or sensor break or power fail Low alarm or sensor break or power fail ROC alarm or sensor break or power fail Decimal places T orr litres/hr litres/min % RH %O2 %CO2 %CP V Amp mA mV Ohm ppm RPM m etres/sec Not used Not configured 4 to 20mA output 0 to 20mA output 0 to 5 V dc output 1 to 5V dc output 0 to 10V dc output 2 to 10V dc output International sales and service DENMARK Copenhagen T (+45 70) 234670 E [email protected] FINLAND Abo T (+358) 22506030 E [email protected] FRANCE Lyon T (+33 478) 664500 E [email protected] GERMANY Limburg T (+49 6431) 2980 E [email protected] INDIA Chennai T (+91 44) 24961129 E [email protected] IRELAND Dublin T (+353 1) 4691800 E [email protected] Digital input A Digital input B x W K U D V J M Y x W K U D V J M Y Not configured Alarm acknowledge Keylock Remote up button Remote down button Recipe 2/ select Alarm inhibit Peak Reset Freeze PV Not configured Alarm acknowledge Keylock Remote up button Remote down button Recipe 2/ select Alarm inhibit Peak Reset Freeze PV www.eurotherm.com ITALY Como T (+39 031) 975111 E [email protected] KOREA Seoul T (+82 31) 2738507 E [email protected] NETHERLANDS Alphen a/d Rijn T (+31 172) 411752 E [email protected] NORWAY Oslo T (+47 67) 592170 E [email protected] POLAND Katowice T (+48 32) 78395000 E [email protected] SPAIN Madrid T (+34 91) 6616001 E [email protected] SWEDEN Malmo T (+46 40) 384500 E [email protected] SWITZERLAND Wollerau T (+41 44) 7871040 E [email protected] UNITED KINGDOM Worthing T (+44 1903) 268500 E [email protected] U.S.A. Ashburn VA T (+1 703) 724 7300 E [email protected] ED61 © Copyright Eurotherm Limited 2010 Invensys, Eurotherm, the Eurotherm logo, Chessell, EurothermSuite, Mini8, Eycon, Eyris, EPower nanodac and Wonderware are trademarks of Invensys plc, its subsidiaries and affiliates. All other brands may be trademarks of their respective owners. All rights are strictly reserved. No part of this document may be reproduced, modified, or transmitted in any form by any means, nor may it be stored in a retrieval system other than for the purpose to act as an aid in operating the equipment to which the document relates, without the prior written permission of Eurotherm limited. Eurotherm Limited pursues a policy of continuous development and product improvement. The specifications in this document may therefore be changed without notice. The information in this document is given in good faith, but is intended for guidance only. Eurotherm Limited will accept no responsibility for any losses arising from errors in this document. Eurotherm Part No. HA029669 Issue 5 June 10 14 EPower Specification Sheet