Transcript
Your Guide
ERSA MS 250 / MS 250 S Soldering Station
ERSA ANALOG 60 Soldering Station The electronically temperature-controlled ANALOG 60 soldering station is the basic model of the ERSA soldering station series. It has the tried and proven ERSA RESISTRONIC temperature control technology, with the ceramic PTC heating element serving as the temperature sensor. The high initial power enables fast heat-up. The large selection of soldering tips allows a broad range of applications. The internal heating provides high thermal efficiency. A front-installed socket with integrated, highimpedance allows potential equalization between the soldering tip and the workplace. The device is primarily used for smaller and medium-sized solder joints. The low-voltage operated soldering iron Basic tool 60 has a highly flexible, heat-resistant connecting cable.
The ERSA MS250 S offers demanding electronics hobbyists temperature control as well as the option of alternatively connecting two different soldering irons. The Multitip soldering iron with 25 W is suitable for standard soldering work; for microsolder joints, as on SMDs, the Minityp iron with 6 W should be used. Internally heated ERSADUR soldering tips combine high efficiency with a long tip service life.
172 soldering tip series see page 51 12 soldering tip series see page 52
ANALOG 60 with Basic tool 60 soldering iron, ERSA RESISTRONIC control system 832 and 842 soldering tip series see page 45 / 46 Order no.
Description
Rating / Voltage
Heating time
0ANA 60
ANALOG 60 soldering station complete with Basic tool 60 soldering iron 0670 CDJ with soldering tip 0832 CD and tool holder 0A 28
60 W / 230 V, 50 - 60 Hz / 24 V 60 W (at 350°C)
approx. 60 s (280°C)
Temperature range 150°C - 450°C
Weight (w/o cable) 60 g
ERSA ANALOG 80 Soldering Station Experienced amateurs and professional users, especially in wiring harness production, etc. have for many years appreciated the unusually wide range of applications of the ERSA ANALOG 80 soldering station and its predecessors. The light and slim Basic tool 80 soldering iron with an internally heated soldering tip has a high level of thermal efficiency. It can even replace commercially available uncontrolled soldering irons of up to 150 W output. The ERSA SENSOTRONIC control system with its thermocouple temperature sensor inside the soldering tip and near the soldering track immediately reacts to any heat loss. Practically delay-free reheating and high temperature constancy are ensured. The soldering tip is connected with high impedance to the front-installed potential equalization socket. Basic tool 80 has a highly flexible, heat-resistant connecting cable. 20
The soldering tip is connected with high impedance to the front-installed potential equalization socket.
MS 250 S*
Order no.
Description
Rating / Voltage
Heating time
0MS 250 S
MS 250 S soldering station complete with Multitip 25 W soldering iron - 0920BDH040, 0172 BD long-life tip, Minityp 6 W soldering iron - 0015BDH040, 0012 BD long-life tip and 0A 26 tool holder
32 W / 230 V, 50 - 60 Hz / 12 V 25 W / 12 V 6 W / 12 V
ca. 60 s ca. 20 s
Temperature range 120°C - 460°C
Weight (w/o cable)
The integrated funnel tool holder can be mounted on the left or right of the station.
34 g 7g
*The MS 250 S is also available as version MS 250. Minityp soldering iron - 0015BDH040 - with 0012 BD long-life soldering tip is not included in this version, however.
ERSA HS 8000 G Hot Air Soldering & Desoldering Station The electronically temperaturecontrolled HS 8000 G hot air soldering and desoldering station is suitable for soldering and desoldering small to medium-sized SMD components. The hot air iron operates with the tried and proven ERSA RESISTRONIC temperature control system, with the PTC heating element also serving as the temperature sensor. The intensity of the air flow and the temperature is continuously variable. The hot gas nozzle is connected with high impedance to the front-installed potential equalization socket.
ANALOG 80
HS 8000 G
with Basic tool 80 soldering iron, ERSA SENSOTRONIC control system 832 and 842 soldering tip series see page 45 / 46
802 soldering tip series see page 47
Order no.
Description
Rating / Voltage
Heating time
0ANA 80
ANALOG 80 soldering station complete with Basic tool 80 soldering iron 0810 CDJ with soldering tip 0832 CD and tool holder 0A 28
80 W / 230 V 50 60 Hz / 24 V 80 W (at 350°C)
approx. 40 s (280°C)
Temperature range 150°C - 450°C
Weight (w/o cable) 50 g
Order no.
Description
Rating / voltage
Heating time
0HS 8000 G
HS 8000 G hot air sold. & desold. station complete with HSP 80 hot air sold. iron 0800 ARJ, tool holder 0A 09 and foot switch 0FES 820
240 W / 230 V, 50 - 60 Hz / 24 V 50 W (hot rating)/ 24 V
approx. 20 s
Temperature range 150°C - 480°C
Weight (w/o. cable)
The power supply unit has a maximum air output of 7 Nl/min. The maximum hot air flow rate of the electronic control unit is 3 l/min.
50 g
21
Your Guide
ERSA ANALOG 60 A Soldering Station
Antistatic Soldering & Desoldering Stations Display temperature 320°C
Reheating of the heating element to compensate heat loss at the soldering tip
Microprocessor controlled Actual temperature
Compensation of the heat loss at the soldering tip
320°C
Compares the actual soldering tip temperature with the set temperature
Measures the heat loss at the soldering tip
tip
The soldering station reacts
immediately to the task!
The tip directly transfers the heat to the soldering spot.
ANALOG 60 A with Ergo tool soldering iron, ERSA RESISTRONIC control system 832 and 842 soldering tip series see page 45 / 46 Order no.
Description
Rating / voltage
Heating time
0ANA 60 A
ANALOG 60 A soldering station complete with Ergo tool soldering iron 0680 CDJ, with Soldering tip 0832 CD and tool holder 0A 29
60 W / 230 V, 50 - 60 Hz / 24 V 60 W (at 350°C)
approx. 60 s (280°C)
Temperature range 150°C - 450°C
Weight (w/o. cable) 60 g
The electronically temperaturecontrolled ERSA ANALOG 60 A soldering station is antistatic according to the MILSPEC / ESA standard and has all the positive features of the ERSA ANALOG 60. It has the tried and proven ERSA RESISTRONIC temperature control technology based on the ceramic PTC heating element and the fast heat-up characteristics. Internally heated tips guarantee high thermal efficiency. The unusually wide range of tips allows a varied range of applications. The front-installed potential equalization socket is connected with high impedance to the soldering tip. The light and slim Ergo tool soldering iron has a highly flexible, heat-resistant and antistatic connecting cable. The ANALOG 60 A soldering station is especially suitable for producing small and medium-sized solder joints. For tip changing we recommend the tip exchanger 3 ZT 00164 with an additional flat nose pliers and side cutter (see p. 40).
ERSA ANALOG 80 A Soldering Station
A 35 Holder for 832 XD mini solder bath series. Delivery without holder 0A 28/29, soldering iron and mini solder bath
High-tech soldering and desoldering, diverse applications and high-precision: easily attained with ERSA top-quality products. Precise temperature measurement near the soldering tip and a microprocessor controlled heating system will guarantee safe lead-free soldering at low temperatures in the future. The ERSA soldering stations‘ high capacity ensures superior reheating. Even high-mass soldering can be carried out without problems.
24
ANALOG 80 A with Power tool soldering iron, ERSA SENSOTRONIC control system 832 and 842 see page 45 / 46 Order no.
Description
Rating / voltage
Heating time
0ANA 80 A
ANALOG 80 A soldering station complete with Power tool soldering iron 0840 CDJ, with soldering tip 0842 CD and tool holder 0A 29
80 W / 230 V, 50 - 60 Hz / 24 V 80 W (at 350°C)
approx. 40 s (280°C)
Temperature range 150°C - 450°C
Weight (w/o. cable) 50 g
The antistatic, electronically temperature-controlled highpowered ERSA ANALOG 80 A soldering station according to the MIL-SPEC / ESA-standard is the ideal tool for producing solder joints with a high heat requirement. The light and slim Power tool soldering iron has high thermal efficiency, and can replace even ordinary uncontrolled soldering irons of up to 150 W power. The ERSA SENSOTRONIC control system with its thermocouple temperature sensor inside the soldering tip and near the soldering track immediately reacts to any heat loss. Practically delay-free reheating and high temperature constancy are ensured. The soldering tip is connected with high impedance to the frontinstalled potential equalization socket. The low-voltage soldering iron Power tool has a highly flexible, heat-resistant and antistatic connecting cable.
25
Your Guide
ERSA DIGITAL 2000 A Desoldering Station with Compressor Unit This desoldering station is suitable for removing residual solder and for desoldering wired components, even from multilayer PCBs. The station consists of the ERSA DIGITAL 2000 A described on pages 26 and 27, a vacuum unit with the X-Tool desoldering iron and the 0A 36 tool holder. The desoldering tip is heated by two PTC heating elements. A thermocouple temperature sensor near the desoldering tip immediately reacts to any heat loss. Practically delayfree reheating is therefore ensured. The vacuum for suctioning the liquefied solder is immediately available when the pushbutton is pressed. The recesses of the combination tool holder 0A 36 / 0SH 09 allow exchanging inserted soldering tips, even when hot, without an additional tool.
X-Tool with compressor unit
28
The Tool Selector is connected instead of the soldering or desoldering tool to the ERSA DIGITAL 2000 A soldering station. The Micro tool, Tech tool, Power tool or Desoldering Pincette 40 can be alternatively used without bothersome re-attachment (see illustration). Thanks to the internally heated soldering and desoldering tips with PTC heating elements, the tools quickly attain their operating temperatures. Changing over to the desired tool also changes the program slot (parameter set) (see pages 26-27). As an alternative to the soldering tools and the SMD Desoldering Pincette 40, the X-Tool desoldering iron can be operated through the Tool Selector. The device requires a line voltage of 230 V / 50 - 60 Hz at a power consumption of 3.5 W.
Application with optional accessories
with electronic station 0DIG 203 A and ERSA SENSOTRONIC control system 722 desoldering tip series see page 47
Figure with optional rack * incl. tip and cable
Order no.
Description
Rating / Voltage
Vacuum
0DIG 20 A XT
DIGITAL 2000 A desoldering station complete with compressor unit 0CU 103 A, X-Tool desoldering iron 0720 ENJ, tip 0722 EN 1223, holders 0A 36 and 0SH 09
80 W / 230 V, 50 - 60 Hz / 24 V 45 W 80 W (350°C)
800 mbar max.
Temperature range 50°C - 450°C
Weight
ERSA Tool Selector
1.25 kg approx. 240 g*
ERSA DIGITAL 2000 A Desoldering Station for External Compressed Air Supply With a suitable compressed air supply (4 - 6 bar, dry and oil-free), this device has the same efficiency as the device described above, which requires only a protected contact socket. The device also consists of the ERSA DIGITAL 2000 A described on pages 26 and 27, along with a venturi unit with the X-Tool desoldering iron and tool holder 0A 36 with 0SH 09. The venturi unit with integrated injector generates the required vacuum at the press of a button, for suctioning superfluous solder without leaving any residue behind. The 0722 ED soldering tips with the greatest possible service life are suitable for standard desoldering jobs. The 0722 EN desoldering tips are mainly used for soldering multilayer PCBs, that is, for solder joints with a high heat requirement.
ERSA Tool Selector
Order no. 0MIC 608 A
Tool Selector
ERSA TWIN 80 A Soldering Station
Ergo tool
X-Tool and venturi unit with electronic station 0DIG 203 A and ERSA SENSOTRONIC control system 722 desoldering tip series see page 47
Figure with optional rack
Micro tool
ERSA TWIN 80 A with Micro tool and Ergo tool soldering irons, ERSA RESISTRONIC control system 832 and 842 soldering tip series see pages 45 / 46, 212 soldering tip series see page 50
* incl. tip and cable Order no.
Description
Rating / voltage
Vacuum
0DIG 20 A VU
DIGITAL 2000 A desoldering station complete with venturi unit for compressed air supply 0VU 103 A, X-Tool desoldering iron 0720 ENJ, with tip 0722 EN 1223, holders 0A 36 and 0SH 09
80 W / 230 V, 50 - 60 Hz / 24 V 230 V / 5 W 80 W (350°C)
900 mbar max.
Temperature range 50°C - 450°C
weight
Order no.
Description
Rating / voltage
Heating time
Temperature range
Weight (w/o. cable)
1.25 kg
0TW 80 A
TWIN 80 A soldering station complete with Ergo tool soldering iron 0680 CDJ, tip 0832 CD, Micro tool soldering iron 0270 BDJ, tip 0212 BD and 2 tool holders 0A 29
80 W / 230 V, 50 - 60 Hz / 24 V 60 W (at 350°C) 20 W (at 350°C)
approx. 60 s (280°C) approx. 50 s (280°C)
150°C - 450°C 150°C - 400°C
approx. 60 g approx. 25 g
approx. 240 g*
The ERSA duo-soldering station TWIN 80 A corresponds to the MIL-SPEC / ESA standard. The TWIN 80 A has two mutually independent, simultaneously operating electronically temperature-controlled soldering tools and is suitable for micro-solder joints, as in SMD technology, and for medium-sized conventional solder joints. Mix-assembled PCBs can then be processed extremely efficiently with low expenditure for technical devices. The Micro tool and Ergo tool soldering irons are connected through their respective, iron-specific plug connectors. Both soldering devices operate with the tried and proven ERSA RESISTRONIC temperature control system, with the ceramic heating element also serving as the temperature sensor. The soldering tips are connected with high impedance to the front-installed potential equalization socket. Both soldering irons have a highly flexible, heat-resistant and antistatic connecting cable. 29
Your Guide
ERSA SMT 60 A SMD Soldering & Desoldering Station The ERSA SMT UNIT 60 A is most often used in the repair of SMD PCBs. It is the basic device for soldering and desoldering the most common SMD components. Antistatic according to the MILSPEC/ESA standard and therefore safe for electrostatically endangered components, this combination station comes with the Micro tool soldering iron and the Desoldering Pincette 40. Both are equipped with the tried and proven ERSA RESISTRONIC temperature control system, with the ceramic PTC heating elements serving as the temperature sensor. The use of these heating elements with a high positive temperature coefficient affords high heat-up power, so that the tools can be brought to the desired operating temperature very fast. The Micro tool soldering iron and the Desoldering Pincette 40 are connected to the 0SMT 603 A electronic station through coded plug connectors to prevent a mixup, and can be independently and simultaneously operated. The internal heating of the tips provides great thermal efficiency. The soldering and desoldering tips are connected with high impedance to the front-installed potential equalization socket. Both tools are equipped with a highly flexible, heat-resistant and antistatic connecting cable. The Mini, Micro and SolderWell soldering tips (see page 50) allow fine-pitch components to be soldered in the shortest possible time with top solder quality. The desoldering tips of the ERSA Desoldering Pincette 40 range from paired desoldering tips for MICROMELFs to inserts for PLCC 84 housing (see page 49). The two duroplastic tool holders have a sponge receptacle with a viscous sponge for tip cleaning and also serve as clearly arranged tip holders. Since the soldering and desoldering tips are only plugged in, they can be easily exchanged using the ERSA tip exchanger 3ZT00164 even when hot.
30
ERSA SMD 8012 and SMD 8013 Tip Holders The SMD 8012 and SMD 8013 tip holders are equipped with the latest soldering tips or desoldering tip pairs, in particular for SMD technology. Tips can be stored neatly arranged for space-saving, quick access.
212 soldering tip series see page 50, 422 desoldering tip series see page 49
ERSA SMD 8013
ERSA SMD 8012
SMT 60 A
Order no. 0SMD 8012
Tip holder SMD 8012 tip holder, complete
Equipped with 212... ERSADUR soldering tips ...BD, ...CD, ...ED, ...KD
0SMD 8013
SMD 8013 tip holder, complete
...BD, ...CD, ...ED, ...MS, ...WD, ...SD, ...FD, ...GD
with Micro tool soldering iron and Desoldering Pincette 40, ERSA RESISTRONIC control system 212 soldering tip series see page 50, 422 soldering tip series see page 49 Order no.
Description
0SMT 60 A
SMT 60 A electronic station complete with 60 W / 230 V, 50 - 60 Hz / 24 V Micro tool soldering iron 0270 BDJ, tip 0212 BD and 20 W (350°C) approx. 50 s (280°C) 150°C - 400°C SMD Desoldering Pincette 40 - 0430 EDJ, tips 0422 ED 40 W (350°C) subject to tips subject to tips and tool holders 0A 29 and 0A 30 Tip turn protection set and fine adjustment for Desoldering Pincette 40, consisting of tip turn protection set E043400 complete, fine adjustment E043600 complete with accessories for holder 0A 30 and desoldering tip pair 0422 SD for MICROMELF Extension set for tip turn protection set E043400 for another desoldering tip pair of the 422 series
E043700 E043500
E043700
Rating / voltage
Heating time
Temperature range
E043500
E043400
Equipped with 422 desoldering tip pairs ...ED, ...FD1, ...FD2, ...QD1, ...QD3, ...QD4, ...QD2, ...MD ...ED, ...FD1, ...FD2, ...FD4, ...FD5, ...FD6, ...QD3, ...QD5, ...MD, ...SD
The range of currently available soldering tips and desoldering tip pairs, with the component-specific dimensions, can be found on pages 49 and 50. All soldering tips and desoldering tip pairs are manufactured according to the ERSADUR process. They have excellent thermal conductance and a long service life.
Weight (w/o. cable) approx. 25 g approx. 75 g
Fig.: SMD Desoldering Pincette 40 with tip turn protection set and fine adjustment for safe desoldering of component sizes as small as 0201.
Award-Winning Rework and Inspection Solutions
E043600
E043700 Tip turn protection set and fine adjustment for Desoldering Pincette 40, complete with desoldering tip pair 0422 SD
Quick and easy SMD rework: A process description on Fine-Pitch soldering and desoldering of SMD components is available at: www.ersa.com
ERSA IR 550 A Rework System Removal of residual solder
Superfine SMD soldering tip (0212 SD)
Desoldering with SMD Desoldering Pincette 40
SMD soldering with the Micro tool
IR 500 AS Rework System
With over 4000 systems installed worldwide, ERSA IR rework technology sets the standards for lead-free, selective reflow processes. The award-winning IR 550 A Rework System is worldwide the only system with a genuine closed loop control system, which employs the current temperature at the component in order to regulate the process. The patented aperture control makes component-specific nozzles and inserts unnecessary. In addition, the system offers the professional user 1,600 W of heating power and repeatable,
top-quality lead-free soldering results. The included ERSA IRSoft allows the lead-free rework process to be fully documented for the first time and represents a milestone in quality assurance for rework processes. ERSA has also achieved a milestone in visual inspection with the ERSASCOPE 2, the 2nd generation of inspection systems. The patented ERSASCOPE, ERSA’s revolutionary contribution to visual inspection under the slogan “To see is to survive,” has been duly further developed.
Full range of rework & inspection solutions made by ERSA. Ask for our free catalogs.
31
