Transcript
ET1500CW
Outdoor Rated Ethernet & PoE Extender Description The ET1500CW is another component of NITEK’s cutting edge EtherStretch line. Our Etherstretch solution allows for the utilization of existing cable infrastructure (coax or UTP) to transmit data from IP cameras and other network devices along with power (PoE) to operate these networked devices over the given wire media. The ET1500CW is apart of a system containing a transmitter that is housed in a NEMA 4X polycarbonate high-impact ABS molded enclosure, which is ideal for use when installing the Etherstretch solution outdoors, and a receiver unit (single or multi-port). Both of the components requires very little installation time and absolutely no set up or configuration. The system can quickly turn ordinary RG59 coax cable into a high speed network communication and PoE pathway.
6.732
4.764
Top (Side View)
0.591
Top (Inside View)
1.07
The ET1500CW is transparent to the network thus requiring no IP and MAC addressing. Simply connect your network devices to the networking ports of the transmitter and receiver along with existing cabling and the system begins communicating. LED indicators show the status of network communication and PoE power. The ET1500CW requires no network settings to be changed or adjusted.
Top (Outside View)
6.732
3.95"
NITEK’s EtherStretch ET1500CW extends network communications to overcome cable distance limitations offering connectivity to devices in locations traditional networking does not allow. The ET1500CW is ideal for retrofitting existing installations.
EL1500C
1.6
Made in USA Right
TOP
Left
Bottom
1.6
4.288 3.602
1.07
4.95"
Features Bottom (Inside View)
Bottom (Outside View)
6.260
7.125
1.640
Bottom (Side View)
● ●
Transmits up to distances of 500 meters (1600 feet)
● ● ● ● ● ● ● ●
Supports mega-pixel technology
● ●
Surge protected inputs
7.125
Available PoE Wattage At PoE Device
Watts
25.5
22.8 18.5
20.0 15.0
16.2
13.8
15.4 13.0
10.0
11.6 11.3
9.3
5.0 0.0
8.0
100 Meters 328 Feet
200 Meters 650 Feet
300 Meters 1,000 Feet
400 Meters 1,300 Feet
500 Meters 1,640 Feet
802.3AT
22.8 Watts
18.5 Watts
16.2 Watts
13.8 Watts
11.6 Watts
802.3AF
15.4 Watts
13.0 Watts
11.3 Watts
9.3 Watts
8.0 Watts
Transmitter is fitted into a NEMA 4X rated enclosure to support outdoor applications Fully transparent to the network Supports any network device, including IP cameras Supports 10/100 and PoE over RG59 cables Easy to install, no set up required No MAC or IP addressing required LED indicators for network signals, link status and power Optional power supply can insert PoE power for non-PoE switches Ground loop isolation
®
5410 Newport Drive, # 24 Rolling Meadows, IL 60008 Phone: (847) 259-8900 Fax: (847) 259-1300 E-mail:
[email protected] WWW.NITEK.NET
RoHS COMPLIANT 2002/95/EC
EUROPE
NITEK
USA
* Results charted were calculated using RG59U coaxial cable with a 20AWG center conductor and power sourcing equipment using IEEE 802.3AF standard with starting voltage of 48 volts DC and IEEE 802.3AT standard with starting voltage of 54 volts DC De Schans 19-21 2a 8231 KA Lelystad Tel: +31(0)320-2300005 Fax: +31(0)320-282186 E-mail:
[email protected] WWW.NITEK.NL
PRODUCT SPECIFICATION
03/24/11
TECHNICAL SPECIFICATION Network Transmission Device Network Port
RJ45 Connector
Link Port
BNC Coax Jack
Ethernet
100BASE-TX Full Duplex
Dimensions Transmitter Enclosure Receiver
6.73” x 4.76 X 2.17 1.1” x 1.6” x 5.1” including tabs & BNC
Operating Temperature
-15° to 60° C / 0° to 140° F
Shipping Weight
5 lbs
Common Installation Type Monitor
Outdoor IP Camera
PoE
PoE
Data
PoE NVR
Data Data
PoE Network Switch
P/T/Z Controller Monitor *PoE is introduced to the system by using a PoE injector (IP1054) in installations where the network switch in not capable of producing power over Ethernet.
PoE
PoE
Data
PoE NVR
Data Data Data
“No PoE” Network Switch
P/T/Z Controller
