Transcript
EURO II HIGH CHAIR Assembly Instructions. Adult Assembly Required. Read all instructions before use. Save instructions for future use. MODEL NUMBERS: 00920 Natural Euro II High Chair (One Step Ahead® #13300-NATU) 00922 Cherry Euro II High Chair (One Step Ahead® #13300-CHER)
VERSION CODE: 6.0/0309/TG BADGER BASKET CO. Toll-Free Customer Service: 1-800-236-1310 (Monday to Thursday 7:30 AM-4:30 PM CST) Web: http://www.badgerbasket.com/parts • E-mail:
[email protected] Mail: PO Box 227, Edgar, WI 54426-0227 • Phone: 715-352-2311 • Fax: 715-352-3163
Manufactured Exclusively for OneStepAhead® PO Box 517, Lake Bluff, IL 60044-0517 Page 1 of 6
6.0/0309/TG
BEFORE YOU BEGIN ASSEMBLY: Check all parts and hardware. If anything is missing or not satisfactory, please DO NOT call One Step Ahead or return the product to them. Contact Badger Basket. Most problems are resolved without you needing to leave home. When contacting us, please have this instruction manual, your product model number, and your product version code ready. For fastest service, go to http://www.badgerbasket.com/parts Your Product Version Code is: 6.0/0309/TG Read all instructions before beginning so you’ll be familiar with the parts and their final positions. CARE INSTRUCTIONS: Wipe the straps and seat cushion with a damp cloth after each use; periodically wipe down the chair with a damp cloth and mild detergent.
WARNING! FAILURE TO FOLLOW THESE WARNINGS AND THE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH WARNING: PREVENT SERIOUS INJURY OR DEATH FROM FALLS OR SLIDING OUT. ALWAYS SECURE CHILD IN THE RESTRAINT. NEVER LEAVE CHILD UNATTENDED.
You may begin using this chair when your child is sitting unassisted. The child should be secured in the high chair at all times by the restraining system, regardless of child’s age/weight or the height position of the seat. ALWAYS keep your child in view while in the chair. NEVER leave your child unattended, not even for “just a minute”. Once the chair is assembled and all the bolts are tightened, the seat and footrest platforms SHOULD NOT HAVE ANY MOVEMENT front to back or side-to-side. If your seat and/or footrest is NOT FIRMLY HELD IN POSITION, DO NOT USE THE CHAIR until you have contacted Badger Basket Company for assistance. DO NOT skip installation of the passive restraint crotch belt if you are installing the Curved Front Rail. Curved Front Rail and Crotch Restraint Belt are ONLY FOR USE WITH THE SEAT PANEL IN THE TOPMOST HEIGHT POSITION. If you adjust the seat height to a lower position for any reason, you MUST REMOVE and not use the Curved Front Rail and Crotch Restraint Belt parts. DO NOT use the high chair if any parts or hardware are broken or missing. REGULARLY check the bolts and retighten as needed using the included allen wrench.
Page 2 of 6
6.0/0309/TG
Parts list A
B
1x Left Side
1x Right Side
F
1x Seat Platform
G
1x Foot Rest Platform
K
L
C
1x Bottom Rail
H
D
2x Curved Back Pieces
I
1x Curved Front Rail
J
1x Seat Cushion 1x Crotch Restraint Belt 1x 5 Point Seat Harness See STEP 2 for information .
M
N
O
2x Connecting Rods
1x Allen Wrench
6x Long Bolts
4x Short Bolts
6x Barrel Nuts
Save this wrench for future use!
M6 x 50mm
M6 x 40mm
M6 x 12mm
Page 3 of 6
E
6.0/0309/TG
IMPORTANT: DO NOT TIGHTEN THE BOLTS UNTIL THE CHAIR IS FULLY ASSEMBLED or you will not be able to insert the Seat and Footrest Platforms and the Curved Front Rail.
1
L
D
N L
L
N
D
N
B
A
N
M
O
L
I M
M
O M L N
C
N
L
I
K
L
M
N
O 1x Allen Wrench
TOOL
2
4xShort Bolts M6 x 40mm
6xBarrel Nuts M6 x 12mm
In the TOPMOST SEATING POSITION, the seat platform MUST be pushed back until it stops and will not slide in any further. Footrest platform MUST be inserted so that at least 21 2 inches stick out the back. Seat must be installed in the TOP height position if you are using the Curved Front Rail and Crotch Restraint Belt.
F
G
Page 4 of 6
6xLong Bolts M6 x 50mm
The 5 POINT SEAT HARNESS (J) is pre-attached to the SEAT PLATFORM (F). It is not shown in the diagrams because no assembly is needed except you must review the proper use of the harness detailed on PAGE 6.
6.0/0309/TG
3
E I
Put the chair into its upright position on a flat, level floor. Level the chair, and then securely tighten ALL of the bolts! Periodically check the bolts to ensure they remain tight. As your child grows you can loosen the bolts to change the position of the seat and foot rest platforms. Be sure to level the chair and then retighten the bolts securely whenever adjustments are made. If the Seat Platform is in any slot other than the top one, you must remove and not use the Curved Front Rail and Crotch Restraint Belt.
4 H
Page 5 of 6
6.0/0309/TG
PROPER USE OF THE 5 POINT SEAT HARNESS (PART J): SEE FIGURE A (BELOW) When your child is sitting in the high chair, the shoulder straps (3) come up BEHIND the chair and OVER THE TOP OF the CURVED BACK RAILS and then down over the child’s shoulders to hook to the harness buckle in front. The waist straps (4) go around the child’s waist and snap into the harness buckle in front, and the crotch strap (5) will rest beneath the child and between the legs. The CROTCH RESTRAINT BELT in FIGURE A was moved out of the way and the seat is in a lower position so the 5-POINT SEAT HARNESS could be shown clearly. It is essential that you install the CROTCH RESTRAINT BELT per the instructions and do not leave it out; and only use the CURVED FRONT RAIL and 5 POINT SEAT HARNESS with the seat in the TOP position as noted in the safety warnings!
FIGURE A 3
3 Part I removed for picture.
4
4 5
Page 6 of 6
6.0/0309/TG
