Evh-1152d/43 Key Features: Single 15” Two-way Coaxial 40° X 30° Full-range

Transcript

EVH-1152D/43 Single 15” Two-Way Coaxial 40° x 30° Full-Range High-Efficiency Loudspeaker System Key Features: • • • • • • • • • DH7N 3” (76 mm) diaphragm, 1.4” (36 mm) exit pure titanium compression driver SMX2151 15” (381 mm) LF transducer with fully symmetric drive Advanced fourth-order crossover network with HF protection Coverage pattern: 40° x 30° Constant DirectivityTM 12” rotatable waveguide 106 dB sensitivity, 139 dB maximum SPL System rating: 500 W continuous, 2000 W peak Active rating: LF 400 W/HF 75 W continuous (1600 W/300 W peak) (28) M10 threaded suspension points PI and FG versions available with gland nut and stainless-steel grille Technical Specifications: Freq. Response1 (-3 dB): 60 Hz - 17 kHz Freq. Range1 (-10 dB): 50 Hz - 20 kHz Rotatable Coverage: 40° x 30° Rec. High-Pass Frequency: 60 Hz Passive Crossover Freq.: 1300 Hz Axial Sensitivity1: 106 dB (1 W/1 m) Max. Calculated SPL1: 139 dB Passive Power Handling2: 500 W continuous, 2000 W peak Impedance: 8 ohms (nominal), 6.0 ohms (min.) LF Transducer - SMX2151, 15” (381 mm) driver LF Axial Sensitivity4: 107 dB (1 W/1 m) LF Max. Calculated SPL: 139 dB LF Power Handling3: 400 W continuous, 1600 W peak LF Impedance: 8 ohms (nominal), 6.1 ohms (min.) HF Transducer - DH7N, 3” (76 mm) diaphragm compression driver HF Axial Sensitivity4: 114 dB (1 W/1 m) HF Max. Calculated SPL: 139 dB HF Power Handling3: 75 W continuous, 300 W peak HF Impedance: 8 ohms (nominal), 6.0 ohms (min.) General Description: The Electro-Voice EVH-1152D/43 is a high-power, two-way horn-loaded coaxial loudspeaker system that can be used in a variety of applications where excellent sound reinforcement, wide bandwidth directivity control, and high efficiency is required in a compact package. The EVH-1152D/43 utilizes the DH7N, a high-output 3” titanium compression driver, coupled to a Constant Directivity™ 40° x 30° waveguide. The SMX2151 15” woofer was developed using FEA optimization for motor, suspension, and electrical design to ensure very low distortion, high efficiency, and maximum intelligibility at high SPL. The crossover uses steep, 24-dB-per-octave slopes with equalization for very smooth response in the vocal range, linear off-axis response, and a protection circuit for long-term reliability. This combination of technologies results in a smooth response to 20 kHz and excellent pattern control down to 500 Hz. The EVH-1152D/43’s features make it ideal for many fixed-install applications. The trapezoidal enclosure is constructed of weather-resistant birch, and coated with EVCoatTM for protection from the elements. For maximum protection against extreme outdoor elements, a fully-weatherized fiberglass version is available. The unique acoustic and rigging design allows for vertical and horizontal clusters to be built using any combination of loudspeakers from the entire EVF and EVH series. With seven horn patterns to choose from, along with an assortment of lowfrequency and subwoofer loudspeakers, you have the tools to maximize flexibility of system design, no matter what the application and budget. The innovative input panel provides a choice of Phoenix-style connector (included in all standard models) or the ability to add a dual NL4-type connector cover plate or gland-nut cover plate (for weatherizing applications). An externally accessible jumper selects passive or active operation. An available 70.7/100-V transformer kit may be easily mounted to the input panel for use in distributed systems. All these features give you the flexibility to address a large range of venues, quickly and precisely supporting customer requirements with fewer items in inventory. Connectors: Dual four-pin 10 AWG Phoenix/Euro Block screw-terminals PI/FG Versions - CDG dual-glandnut input panel cover included Enclosure: 13-ply weather-resistant FG Version - 13-ply weather-resisbirch with EVCoatTM tant birch with fiberglass finish Grille: 16 GA powder-coated galvanneal with rotatable logo PI/FG Versions Stainless steel with hydrophobic cloth Environmental: IEC 60529 IP55 for PI and FG versions Suspension: (28) M10 threaded suspension points Dimensions 30.26” x 30.26” x 26.77” (H x W x D): (768.6 mm x 768.6 mm x 680.1 mm) Weight: 145.5 lb (66.1 kg) net, 160.5 lb (72.9 kg) shipping Half-space measurement. 2 EIA RS-426A, tested for eight hours. 1 3 4 AES 2-1984, tested for eight hours. Arithmetic averages, 300 - 1,300 Hz (LF) and 1,300 - 5,000 Hz (HF). EVH-1152D/43 Loudspeaker System Frequency Response & Impedance: Horizontal Off-Axis Frequency Response: 100 100 100 90 Passive Mode, Half Space Impedance, Passive Mode 20 50 100 1000 10000 90 80 10 80 70 SPL (dB) 1W/1m 110 Impedance (Ohms) 316 SPL (dB) 1W/1m 110 70 3.16 20000 20 50 100 On Axis 10° Horizontal 20° Horizontal 30° Horizontal 1000 10000 20000 Frequency (Hz) Frequency (Hz) Vertical Off-Axis Frequency Response: 110 SPL (dB) 1W/1m 100 90 80 70 On Axis 10° Vertical 20° Vertical 20 50 100 1000 5° Vertical 15° Vertical 10000 20000 Frequency (Hz) Directivity: Horizontal Vertical Directivity Index (DI), dB -6dB Beamwidth (degrees) 360 100 50 20 30 1000 20 100 Directivity Factor (Q) Beamwidth: 10 0 3.6 20 100 1000 Frequency (Hz) Block Diagram (biamp): 10000 20000 10 20 100 1000 Frequency (Hz) Block Diagram (passive): 10000 1 20000 Engineering Data Sheet Polar Plots (1/3 Octave): 400 Hz 500 Hz 630 Hz 1.6 kHz 800 Hz 1 kHz 1.25 kHz 2.5 kHz 3.15 kHz 4 kHz 5 kHz 6.3 kHz 8 kHz 10 kHz 12.5 kHz 16 kHz 20 kHz Horizontal = Black Vertical = Grey 2 kHz Dimension Drawings: End View Front View Side View EVH-1152D/43 Part Numbers • PRD000303-001 EVH-1152D/43-BLK, 40° x 30°, black finish • PRD000303-002 EVH-1152D/43-WHT, 40° x 30°, white finish • PRD000303-003 EVH-1152D/43-PIB, 40° x 30°, black finish, weather resistant • PRD000303-004 EVH-1152D/43-PIW, 40° x 30°, white finish, weather resistant • PRD000303-005 EVH-1152D/43-FGB, 40° x 30°, black finish, weather resistant fiberglass • PRD000303-006 EVH-1152D/43-FGW, 40° x 30°, white finish, weather resistant fiberglass Performance Match • • • • • • • • • • • PRD000304 PRD000305 PRD000306 PRD000307 PRD000308 PRD000300 PRD000302 CPS2.9 120V CPS2.12 120V D170469 D170466 EVH-1152D/64, 60° x 40° coverage EVH-1152D/66, 60° x 60° coverage EVH-1152D/94, 90° x 40° coverage EVH-1152D/96, 90° x 60° coverage EVH-1152D/99, 90° x 90° coverage EVF-2121S, dual 12” bass element EVF-2151D, dual 15” bass element CPS2.9, 120V power amplifier, 2 x 900W CPS2.12, 120V power amplifier, 2 x 1200W CPS4.5, 120V power amplifier, 4 x 500W CPS4.10, 120V power amplifier, 4 x 1000W Electro-Voice 12000 Portland Avenue South, Burnsville, MN 55337 Phone: 952/884-4051, Fax: 952/884-0043 www.electrovoice.com © Bosch Communications Systems Part Number LIT000467043 Rev A 07/2010 Rear View CAUTION This EVH loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the EVF/EVH User Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances. Accessories • • • • • • • • • • • • • • • • ACC000084-000 ACC000085-000 ACC000086-000 ACC000087-000 ACC000089-001 ACC000089-002 ACC000090-001 ACC000090-002 ACC000091-001 ACC000091-002 ACC000092-001 ACC000092-002 ACC000093-001 ACC000093-002 ACC000094-001 ACC000094-002 CDNL4, cover plate, dual NL4 CSG, cover plate, single gland nut CDG, cover plate, dual gland nut TK-150, 70V transformer, 150W HRK-1B, horiz. rigging kit, EVF, black HRK-1W, horiz. rigging kit, EVF, white HRK-2B, horiz. rigging kit, EVF-SUB, black HRK-2W, horiz. rigging kit, EVF-SUB, white HRK-3B, horiz. rigging kit, EVH, black HRK-3W, horiz. rigging kit, EVH, white VRK-1B, vert. rigging kit, EVF, black VRK-1W, vert. rigging kit, EVF, white VRK-2B, vert. rigging kit, EVF-SUB, black VRK-2W, vert. rigging kit, EVF-SUB, white VRK-3B, vert. rigging kit, EVH, black VRK-3W, vert. rigging kit, EVH, white U.S.A. and Canada only. For customer orders, contact Customer Service at: 800/392-3497 Fax: 800/955-6831 Europe, Africa, and Middle East only. For customer orders, contact Customer Service at: + 49 9421-706 0 Fax: + 49 9421-706 265 Other Internatonal locations. For customer orders, Contact Customer Service at: + 1 952 884-4051 Fax: + 1 952 887-9212 For warranty repair or service information, contact the Service Repair department at: 800/685-2606 For technical assistance, contact Technical Support at: 866/78AUDIO Specifications subject to change without notice. EVH-1152D/64 Single 15” Two-Way Coaxial 60° x 40° Full-Range High-Efficiency Loudspeaker System Key Features: • • • • • • • • • DH7N 3” (76 mm) diaphragm, 1.4” (36 mm) exit pure titanium compression driver SMX2151 15” (381 mm) LF transducer with fully symmetric drive Advanced fourth-order crossover network with HF protection Coverage pattern: 60° x 40° Constant DirectivityTM 12” rotatable waveguide 105 dB sensitivity, 138 dB maximum SPL System rating: 500 W continuous, 2000 W peak Active rating: LF 400 W/HF 75 W continuous (1600 W/300 W peak) (28) M10 threaded suspension points PI and FG versions available with gland nut and stainless-steel grille Technical Specifications: Freq. Response1 (-3 dB): 60 Hz - 17 kHz Freq. Range1 (-10 dB): 50 Hz - 20 kHz Rotatable Coverage: 60° x 40° Rec. High-Pass Frequency: 60 Hz Passive Crossover Freq.: 1300 Hz Axial Sensitivity1: 105 dB (1 W/1 m) Max. Calculated SPL1: 138 dB Passive Power Handling2: 500 W continuous, 2000 W peak Impedance: 8 ohms (nominal), 6.0 ohms (min.) LF Transducer - SMX2151, 15” (381 mm) driver LF Axial Sensitivity4: 106 dB (1 W/1 m) LF Max. Calculated SPL: 138 dB LF Power Handling3: 400 W continuous, 1600 W peak LF Impedance: 8 ohms (nominal), 6.1 ohms (min.) HF Transducer - DH7N, 3” (76 mm) diaphragm compression driver HF Axial Sensitivity4: 113 dB (1 W/1 m) HF Max. Calculated SPL: 138 dB HF Power Handling3: 75 W continuous, 300 W peak HF Impedance: 8 ohms (nominal), 6.0 ohms (min.) General Description: The Electro-Voice EVH-1152D/64 is a high-power, two-way horn-loaded coaxial loudspeaker system that can be used in a variety of applications where excellent sound reinforcement, wide bandwidth directivity control, and high efficiency is required in a compact package. The EVH-1152D/64 utilizes the DH7N, a high-output 3” titanium compression driver, coupled to a Constant Directivity™ 60° x 40° waveguide. The SMX2151 15” woofer was developed using FEA optimization for motor, suspension, and electrical design to ensure very low distortion, high efficiency, and maximum intelligibility at high SPL. The crossover uses steep, 24-dB-per-octave slopes with equalization for very smooth response in the vocal range, linear off-axis response, and a protection circuit for long-term reliability. This combination of technologies results in a smooth response to 20 kHz and excellent pattern control down to 500 Hz. The EVH-1152D/64’s features make it ideal for many fixed-install applications. The trapezoidal enclosure is constructed of weather-resistant birch, and coated with EVCoatTM for protection from the elements. For maximum protection against extreme outdoor elements, a fully-weatherized fiberglass version is available. The unique acoustic and rigging design allows for vertical and horizontal clusters to be built using any combination of loudspeakers from the entire EVF and EVH series. With seven horn patterns to choose from, along with an assortment of lowfrequency and subwoofer loudspeakers, you have the tools to maximize flexibility of system design, no matter what the application and budget. The innovative input panel provides a choice of Phoenix-style connector (included in all standard models) or the ability to add a dual NL4-type connector cover plate or gland-nut cover plate (for weatherizing applications). An externally accessible jumper selects passive or active operation. An available 70.7/100-V transformer kit may be easily mounted to the input panel for use in distributed systems. All these features give you the flexibility to address a large range of venues, quickly and precisely supporting customer requirements with fewer items in inventory. Connectors: Dual four-pin 10 AWG Phoenix/Euro Block screw-terminals PI/FG Versions - CDG dual-glandnut input panel cover included Enclosure: 13-ply weather-resistant FG Version - 13-ply weather-resisbirch with EVCoatTM tant birch with fiberglass finish Grille: 16 GA powder-coated galvanneal with rotatable logo PI/FG Versions Stainless steel with hydrophobic cloth Environmental: IEC 60529 IP55 for PI and FG versions Suspension: (28) M10 threaded suspension points Dimensions 30.26” x 30.26” x 26.77” (H x W x D): (768.6 mm x 768.6 mm x 680.1 mm) Weight: 145.5 lb (66.1 kg) net, 160.5 lb (72.9 kg) shipping Half-space measurement. 2 EIA RS-426A, tested for eight hours. 1 3 4 AES 2-1984, tested for eight hours. Arithmetic averages, 300 - 1,300 Hz (LF) and 1,300 - 5,000 Hz (HF). EVH-1152D/64 Loudspeaker System Frequency Response & Impedance: Horizontal Off-Axis Frequency Response: 100 100 100 90 Passive Mode, Half Space Impedance, Passive Mode 20 50 100 1000 10000 90 80 10 80 70 SPL (dB) 1W/1m 110 Impedance (Ohms) 316 SPL (dB) 1W/1m 110 70 3.16 20000 20 50 100 On Axis 10° Horizontal 20° Horizontal 30° Horizontal 1000 10000 20000 Frequency (Hz) Frequency (Hz) Vertical Off-Axis Frequency Response: 110 SPL (dB) 1W/1m 100 90 80 On Axis 70 20 50 100 10° Vertical 1000 20° Vertical 10000 20000 Frequency (Hz) Directivity: Horizontal Vertical Directivity Index (DI), dB -6dB Beamwidth (degrees) 360 100 50 20 3.6 20 100 1000 Frequency (Hz) Block Diagram (biamp): 10000 20000 30 1000 20 100 Directivity Factor (Q) Beamwidth: 10 0 10 20 100 1000 Frequency (Hz) Block Diagram (passive): 10000 1 20000 Engineering Data Sheet Polar Plots (1/3 Octave): 400 Hz 500 Hz 630 Hz 1.6 kHz 800 Hz 1 kHz 1.25 kHz 2.5 kHz 3.15 kHz 4 kHz 5 kHz 6.3 kHz 8 kHz 10 kHz 12.5 kHz 16 kHz 20 kHz Horizontal = Black Vertical = Grey 2 kHz Dimension Drawings: End View Front View Side View EVH-1152D/64 Part Numbers • PRD000304-001 EVH-1152D/64-BLK, 60° x 40°, black finish • PRD000304-002 EVH-1152D/64-WHT, 60° x 40°, white finish • PRD000304-003 EVH-1152D/64-PIB, 60° x 40°, black finish, weather resistant • PRD000304-004 EVH-1152D/64-PIW, 60° x 40°, white finish, weather resistant • PRD000304-005 EVH-1152D/64-FGB, 60° x 40°, black finish, weather resistant fiberglass • PRD000304-006 EVH-1152D/64-FGW, 60° x 40°, white finish, weather resistant fiberglass Performance Match • • • • • • • • • • • PRD000303 PRD000305 PRD000306 PRD000307 PRD000308 PRD000300 PRD000302 CPS2.9 120V CPS2.12 120V D170469 D170466 EVH-1152D/43, 40° x 30° coverage EVH-1152D/66, 60° x 60° coverage EVH-1152D/94, 90° x 40° coverage EVH-1152D/96, 90° x 60° coverage EVH-1152D/99, 90° x 90° coverage EVF-2121S, dual 12” bass element EVF-2151D, dual 15” bass element CPS2.9, 120V power amplifier, 2 x 900W CPS2.12, 120V power amplifier, 2 x 1200W CPS4.5, 120V power amplifier, 4 x 500W CPS4.10, 120V power amplifier, 4 x 1000W Electro-Voice 12000 Portland Avenue South, Burnsville, MN 55337 Phone: 952/884-4051, Fax: 952/884-0043 www.electrovoice.com © Bosch Communications Systems Part Number LIT000467064 Rev A 07/2010 Rear View CAUTION This EVH loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the EVF/EVH User Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances. Accessories • • • • • • • • • • • • • • • • ACC000084-000 ACC000085-000 ACC000086-000 ACC000087-000 ACC000089-001 ACC000089-002 ACC000090-001 ACC000090-002 ACC000091-001 ACC000091-002 ACC000092-001 ACC000092-002 ACC000093-001 ACC000093-002 ACC000094-001 ACC000094-002 CDNL4, cover plate, dual NL4 CSG, cover plate, single gland nut CDG, cover plate, dual gland nut TK-150, 70V transformer, 150W HRK-1B, horiz. rigging kit, EVF, black HRK-1W, horiz. rigging kit, EVF, white HRK-2B, horiz. rigging kit, EVF-SUB, black HRK-2W, horiz. rigging kit, EVF-SUB, white HRK-3B, horiz. rigging kit, EVH, black HRK-3W, horiz. rigging kit, EVH, white VRK-1B, vert. rigging kit, EVF, black VRK-1W, vert. rigging kit, EVF, white VRK-2B, vert. rigging kit, EVF-SUB, black VRK-2W, vert. rigging kit, EVF-SUB, white VRK-3B, vert. rigging kit, EVH, black VRK-3W, vert. rigging kit, EVH, white U.S.A. and Canada only. For customer orders, contact Customer Service at: 800/392-3497 Fax: 800/955-6831 Europe, Africa, and Middle East only. For customer orders, contact Customer Service at: + 49 9421-706 0 Fax: + 49 9421-706 265 Other Internatonal locations. For customer orders, Contact Customer Service at: + 1 952 884-4051 Fax: + 1 952 887-9212 For warranty repair or service information, contact the Service Repair department at: 800/685-2606 For technical assistance, contact Technical Support at: 866/78AUDIO Specifications subject to change without notice. EVH-1152D/66 Single 15” Two-Way Coaxial 60° x 60° Full-Range High-Efficiency Loudspeaker System Key Features: • • • • • • • • • DH7N 3” (76 mm) diaphragm, 1.4” (36 mm) exit pure titanium compression driver SMX2151 15” (381 mm) LF transducer with fully symmetric drive Advanced fourth-order crossover network with HF protection Coverage pattern: 60° x 60° Constant DirectivityTM 12” rotatable waveguide 105 dB sensitivity, 138 dB maximum SPL System rating: 500 W continuous, 2000 W peak Active rating: LF 400 W/HF 75 W continuous (1600 W/300 W peak) (28) M10 threaded suspension points PI and FG versions available with gland nut and stainless-steel grille Technical Specifications: Freq. Response1 (-3 dB): 60 Hz - 17 kHz Freq. Range1 (-10 dB): 50 Hz - 20 kHz Rotatable Coverage: 60° x 60° Rec. High-Pass Frequency: 60 Hz Passive Crossover Freq.: 1300 Hz Axial Sensitivity1: 105 dB (1 W/1 m) Max. Calculated SPL1: 138 dB Passive Power Handling2: 500 W continuous, 2000 W peak Impedance: 8 ohms (nominal), 6.0 ohms (min.) LF Transducer - SMX2151, 15” (381 mm) driver LF Axial Sensitivity4: 106 dB (1 W/1 m) LF Max. Calculated SPL: 138 dB LF Power Handling3: 400 W continuous, 1600 W peak LF Impedance: 8 ohms (nominal), 6.1 ohms (min.) HF Transducer - DH7N, 3” (76 mm) diaphragm compression driver HF Axial Sensitivity4: 112 dB (1 W/1 m) HF Max. Calculated SPL: 137 dB HF Power Handling3: 75 W continuous, 300 W peak HF Impedance: 8 ohms (nominal), 6.0 ohms (min.) General Description: The Electro-Voice EVH-1152D/66 is a high-power, two-way horn-loaded coaxial loudspeaker system that can be used in a variety of applications where excellent sound reinforcement, wide bandwidth directivity control, and high efficiency is required in a compact package. The EVH-1152D/66 utilizes the DH7N, a high-output 3” titanium compression driver, coupled to a Constant Directivity™ 60° x 60° waveguide. The SMX2151 15” woofer was developed using FEA optimization for motor, suspension, and electrical design to ensure very low distortion, high efficiency, and maximum intelligibility at high SPL. The crossover uses steep, 24-dB-per-octave slopes with equalization for very smooth response in the vocal range, linear off-axis response, and a protection circuit for long-term reliability. This combination of technologies results in a smooth response to 20 kHz and excellent pattern control down to 500 Hz. The EVH-1152D/66’s features make it ideal for many fixed-install applications. The trapezoidal enclosure is constructed of weather-resistant birch, and coated with EVCoatTM for protection from the elements. For maximum protection against extreme outdoor elements, a fully-weatherized fiberglass version is available. The unique acoustic and rigging design allows for vertical and horizontal clusters to be built using any combination of loudspeakers from the entire EVF and EVH series. With seven horn patterns to choose from, along with an assortment of lowfrequency and subwoofer loudspeakers, you have the tools to maximize flexibility of system design, no matter what the application and budget. The innovative input panel provides a choice of Phoenix-style connector (included in all standard models) or the ability to add a dual NL4-type connector cover plate or gland-nut cover plate (for weatherizing applications). An externally accessible jumper selects passive or active operation. An available 70.7/100-V transformer kit may be easily mounted to the input panel for use in distributed systems. All these features give you the flexibility to address a large range of venues, quickly and precisely supporting customer requirements with fewer items in inventory. Connectors: Dual four-pin 10 AWG Phoenix/Euro Block screw-terminals PI/FG Versions - CDG dual-glandnut input panel cover included Enclosure: 13-ply weather-resistant FG Version - 13-ply weather-resisbirch with EVCoatTM tant birch with fiberglass finish Grille: 16 GA powder-coated galvanneal with rotatable logo PI/FG Versions Stainless steel with hydrophobic cloth Environmental: IEC 60529 IP55 for PI and FG versions Suspension: (28) M10 threaded suspension points Dimensions 30.26” x 30.26” x 26.77” (H x W x D): (768.6 mm x 768.6 mm x 680.1 mm) Weight: 145.5 lb (66.1 kg) net, 160.5 lb (72.9 kg) shipping Half-space measurement. 2 EIA RS-426A, tested for eight hours. 1 3 4 AES 2-1984, tested for eight hours. Arithmetic averages, 300 - 1,300 Hz (LF) and 1,300 - 5,000 Hz (HF). EVH-1152D/66 Loudspeaker System Frequency Response & Impedance: Horizontal Off-Axis Frequency Response: 100 100 100 90 Passive Mode, Half Space Impedance, Passive Mode 20 50 100 1000 10000 90 80 10 80 70 SPL (dB) 1W/1m 110 Impedance (Ohms) 316 SPL (dB) 1W/1m 110 70 3.16 20000 20 50 100 On Axis 10° Horizontal 20° Horizontal 30° Horizontal 1000 10000 20000 Frequency (Hz) Frequency (Hz) Vertical Off-Axis Frequency Response: 110 SPL (dB) 1W/1m 100 90 80 70 20 50 100 On Axis 10° Vertical 20° Vertical 30° Vertical 1000 10000 20000 Frequency (Hz) Directivity: Horizontal Vertical Directivity Index (DI), dB -6dB Beamwidth (degrees) 360 100 50 20 30 1000 20 100 Directivity Factor (Q) Beamwidth: 10 0 3.6 20 100 1000 Frequency (Hz) Block Diagram (biamp): 10000 20000 10 20 100 1000 Frequency (Hz) Block Diagram (passive): 10000 1 20000 Engineering Data Sheet Polar Plots (1/3 Octave): 400 Hz 500 Hz 630 Hz 1.6 kHz 800 Hz 1 kHz 1.25 kHz 2.5 kHz 3.15 kHz 4 kHz 5 kHz 6.3 kHz 8 kHz 10 kHz 12.5 kHz 16 kHz 20 kHz Horizontal = Black Vertical = Grey 2 kHz Dimension Drawings: End View Front View Side View EVH-1152D/66 Part Numbers • PRD000305-001 EVH-1152D/66-BLK, 60° x 60°, black finish • PRD000305-002 EVH-1152D/66-WHT, 60° x 60°, white finish • PRD000305-003 EVH-1152D/66-PIB, 60° x 60°, black finish, weather resistant • PRD000305-004 EVH-1152D/66-PIW, 60° x 60°, white finish, weather resistant • PRD000305-005 EVH-1152D/66-FGB, 60° x 60°, black finish, weather resistant fiberglass • PRD000305-006 EVH-1152D/66-FGW, 60° x 60°, white finish, weather resistant fiberglass Performance Match • • • • • • • • • • • PRD000303 PRD000304 PRD000306 PRD000307 PRD000308 PRD000300 PRD000302 CPS2.9 120V CPS2.12 120V D170469 D170466 EVH-1152D/43, 40° x 30° coverage EVH-1152D/64, 60° x 40° coverage EVH-1152D/94, 90° x 40° coverage EVH-1152D/96, 90° x 60° coverage EVH-1152D/99, 90° x 90° coverage EVF-2121S, dual 12” bass element EVF-2151D, dual 15” bass element CPS2.9, 120V power amplifier, 2 x 900W CPS2.12, 120V power amplifier, 2 x 1200W CPS4.5, 120V power amplifier, 4 x 500W CPS4.10, 120V power amplifier, 4 x 1000W Electro-Voice 12000 Portland Avenue South, Burnsville, MN 55337 Phone: 952/884-4051, Fax: 952/884-0043 www.electrovoice.com © Bosch Communications Systems Part Number LIT000467066 Rev A 07/2010 Rear View CAUTION This EVH loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the EVF/EVH User Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances. Accessories • • • • • • • • • • • • • • • • ACC000084-000 ACC000085-000 ACC000086-000 ACC000087-000 ACC000089-001 ACC000089-002 ACC000090-001 ACC000090-002 ACC000091-001 ACC000091-002 ACC000092-001 ACC000092-002 ACC000093-001 ACC000093-002 ACC000094-001 ACC000094-002 CDNL4, cover plate, dual NL4 CSG, cover plate, single gland nut CDG, cover plate, dual gland nut TK-150, 70V transformer, 150W HRK-1B, horiz. rigging kit, EVF, black HRK-1W, horiz. rigging kit, EVF, white HRK-2B, horiz. rigging kit, EVF-SUB, black HRK-2W, horiz. rigging kit, EVF-SUB, white HRK-3B, horiz. rigging kit, EVH, black HRK-3W, horiz. rigging kit, EVH, white VRK-1B, vert. rigging kit, EVF, black VRK-1W, vert. rigging kit, EVF, white VRK-2B, vert. rigging kit, EVF-SUB, black VRK-2W, vert. rigging kit, EVF-SUB, white VRK-3B, vert. rigging kit, EVH, black VRK-3W, vert. rigging kit, EVH, white U.S.A. and Canada only. For customer orders, contact Customer Service at: 800/392-3497 Fax: 800/955-6831 Europe, Africa, and Middle East only. For customer orders, contact Customer Service at: + 49 9421-706 0 Fax: + 49 9421-706 265 Other Internatonal locations. For customer orders, Contact Customer Service at: + 1 952 884-4051 Fax: + 1 952 887-9212 For warranty repair or service information, contact the Service Repair department at: 800/685-2606 For technical assistance, contact Technical Support at: 866/78AUDIO Specifications subject to change without notice. EVH-1152D/94 Single 15” Two-Way Coaxial 90° x 40° Full-Range High-Efficiency Loudspeaker System Key Features: • • • • • • • • • DH7N 3” (76 mm) diaphragm, 1.4” (36 mm) exit pure titanium compression driver SMX2151 15” (381 mm) LF transducer with fully symmetric drive Advanced fourth-order crossover network with HF protection Coverage pattern: 90° x 40° Constant DirectivityTM 12” rotatable waveguide 105 dB sensitivity, 138 dB maximum SPL System rating: 500 W continuous, 2000 W peak Active rating: LF 400 W/HF 75 W continuous (1600 W/300 W peak) (28) M10 threaded suspension points PI and FG versions available with gland nut and stainless-steel grille Technical Specifications: Freq. Response1 (-3 dB): 60 Hz - 17 kHz Freq. Range1 (-10 dB): 50 Hz - 20 kHz Rotatable Coverage: 90° x 40° Rec. High-Pass Frequency: 60 Hz Passive Crossover Freq.: 1300 Hz Axial Sensitivity1: 105 dB (1 W/1 m) Max. Calculated SPL1: 138 dB Passive Power Handling2: 500 W continuous, 2000 W peak Impedance: 8 ohms (nominal), 6.0 ohms (min.) LF Transducer - SMX2151, 15” (381 mm) driver LF Axial Sensitivity4: 106 dB (1 W/1 m) LF Max. Calculated SPL: 138 dB LF Power Handling3: 400 W continuous, 1600 W peak LF Impedance: 8 ohms (nominal), 6.1 ohms (min.) HF Transducer - DH7N, 3” (76 mm) diaphragm compression driver HF Axial Sensitivity4: 112 dB (1 W/1 m) HF Max. Calculated SPL: 137 dB HF Power Handling3: 75 W continuous, 300 W peak HF Impedance: 8 ohms (nominal), 6.0 ohms (min.) General Description: The Electro-Voice EVH-1152D/94 is a high-power, two-way horn-loaded coaxial loudspeaker system that can be used in a variety of applications where excellent sound reinforcement, wide bandwidth directivity control, and high efficiency is required in a compact package. The EVH-1152D/94 utilizes the DH7N, a high-output 3” titanium compression driver, coupled to a Constant Directivity™ 90° x 40° waveguide. The SMX2151 15” woofer was developed using FEA optimization for motor, suspension, and electrical design to ensure very low distortion, high efficiency, and maximum intelligibility at high SPL. The crossover uses steep, 24-dB-per-octave slopes with equalization for very smooth response in the vocal range, linear off-axis response, and a protection circuit for long-term reliability. This combination of technologies results in a smooth response to 20 kHz and excellent pattern control down to 500 Hz. The EVH-1152D/94’s features make it ideal for many fixed-install applications. The trapezoidal enclosure is constructed of weather-resistant birch, and coated with EVCoatTM for protection from the elements. For maximum protection against extreme outdoor elements, a fully-weatherized fiberglass version is available. The unique acoustic and rigging design allows for vertical and horizontal clusters to be built using any combination of loudspeakers from the entire EVF and EVH series. With seven horn patterns to choose from, along with an assortment of lowfrequency and subwoofer loudspeakers, you have the tools to maximize flexibility of system design, no matter what the application and budget. The innovative input panel provides a choice of Phoenix-style connector (included in all standard models) or the ability to add a dual NL4-type connector cover plate or gland-nut cover plate (for weatherizing applications). An externally accessible jumper selects passive or active operation. An available 70.7/100-V transformer kit may be easily mounted to the input panel for use in distributed systems. All these features give you the flexibility to address a large range of venues, quickly and precisely supporting customer requirements with fewer items in inventory. Connectors: Dual four-pin 10 AWG Phoenix/Euro Block screw-terminals PI/FG Versions - CDG dual-glandnut input panel cover included Enclosure: 13-ply weather-resistant FG Version - 13-ply weather-resisbirch with EVCoatTM tant birch with fiberglass finish Grille: 16 GA powder-coated galvanneal with rotatable logo PI/FG Versions Stainless steel with hydrophobic cloth Environmental: IEC 60529 IP55 for PI and FG versions Suspension: (28) M10 threaded suspension points Dimensions 30.26” x 30.26” x 26.77” (H x W x D): (768.6 mm x 768.6 mm x 680.1 mm) Weight: 145.5 lb (66.1 kg) net, 160.5 lb (72.9 kg) shipping Half-space measurement. 2 EIA RS-426A, tested for eight hours. 1 3 4 AES 2-1984, tested for eight hours. Arithmetic averages, 300 - 1,300 Hz (LF) and 1,300 - 5,000 Hz (HF). EVH-1152D/94 Loudspeaker System Frequency Response & Impedance: Horizontal Off-Axis Frequency Response: 100 100 100 90 Passive Mode, Half Space Impedance, Passive Mode 20 50 100 1000 10000 90 80 10 80 70 SPL (dB) 1W/1m 110 Impedance (Ohms) 316 SPL (dB) 1W/1m 110 70 3.16 20000 On Axis 20° Horizontal 40° Horizontal 20 50 100 10° Horizontal 30° Horizontal 50° Horizontal 1000 10000 20000 Frequency (Hz) Frequency (Hz) Vertical Off-Axis Frequency Response: 110 SPL (dB) 1W/1m 100 90 80 70 20 50 100 On Axis 10° Vertical 20° Vertical 30° Vertical 1000 10000 20000 Frequency (Hz) Directivity: Horizontal Vertical Directivity Index (DI), dB -6dB Beamwidth (degrees) 360 100 50 20 30 1000 20 100 Directivity Factor (Q) Beamwidth: 10 0 3.6 20 100 1000 Frequency (Hz) Block Diagram (biamp): 10000 20000 10 20 100 1000 Frequency (Hz) Block Diagram (passive): 10000 1 20000 Engineering Data Sheet Polar Plots (1/3 Octave): 400 Hz 500 Hz 630 Hz 1.6 kHz 800 Hz 1 kHz 1.25 kHz 2.5 kHz 3.15 kHz 4 kHz 5 kHz 6.3 kHz 8 kHz 10 kHz 12.5 kHz 16 kHz 20 kHz Horizontal = Black Vertical = Grey 2 kHz Dimension Drawings: End View Front View Side View EVH-1152D/94 Part Numbers • PRD000306-001 EVH-1152D/94-BLK, 90° x 40°, black finish • PRD000306-002 EVH-1152D/94-WHT, 90° x 40°, white finish • PRD000306-003 EVH-1152D/94-PIB, 90° x 40°, black finish, weather resistant • PRD000306-004 EVH-1152D/94-PIW, 90° x 40°, white finish, weather resistant • PRD000306-005 EVH-1152D/94-FGB, 90° x 40°, black finish, weather resistant fiberglass • PRD000306-006 EVH-1152D/94-FGW, 90° x 40°, white finish, weather resistant fiberglass Performance Match • • • • • • • • • • • PRD000303 PRD000304 PRD000305 PRD000307 PRD000308 PRD000300 PRD000302 CPS2.9 120V CPS2.12 120V D170469 D170466 EVH-1152D/43, 40° x 30° coverage EVH-1152D/64, 60° x 40° coverage EVH-1152D/66, 60° x 60° coverage EVH-1152D/96, 90° x 60° coverage EVH-1152D/99, 90° x 90° coverage EVF-2121S, dual 12” bass element EVF-2151D, dual 15” bass element CPS2.9, 120V power amplifier, 2 x 900W CPS2.12, 120V power amplifier, 2 x 1200W CPS4.5, 120V power amplifier, 4 x 500W CPS4.10, 120V power amplifier, 4 x 1000W Electro-Voice 12000 Portland Avenue South, Burnsville, MN 55337 Phone: 952/884-4051, Fax: 952/884-0043 www.electrovoice.com © Bosch Communications Systems Part Number LIT000467094 Rev A 07/2010 Rear View CAUTION This EVH loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the EVF/EVH User Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances. Accessories • • • • • • • • • • • • • • • • ACC000084-000 ACC000085-000 ACC000086-000 ACC000087-000 ACC000089-001 ACC000089-002 ACC000090-001 ACC000090-002 ACC000091-001 ACC000091-002 ACC000092-001 ACC000092-002 ACC000093-001 ACC000093-002 ACC000094-001 ACC000094-002 CDNL4, cover plate, dual NL4 CSG, cover plate, single gland nut CDG, cover plate, dual gland nut TK-150, 70V transformer, 150W HRK-1B, horiz. rigging kit, EVF, black HRK-1W, horiz. rigging kit, EVF, white HRK-2B, horiz. rigging kit, EVF-SUB, black HRK-2W, horiz. rigging kit, EVF-SUB, white HRK-3B, horiz. rigging kit, EVH, black HRK-3W, horiz. rigging kit, EVH, white VRK-1B, vert. rigging kit, EVF, black VRK-1W, vert. rigging kit, EVF, white VRK-2B, vert. rigging kit, EVF-SUB, black VRK-2W, vert. rigging kit, EVF-SUB, white VRK-3B, vert. rigging kit, EVH, black VRK-3W, vert. rigging kit, EVH, white U.S.A. and Canada only. For customer orders, contact Customer Service at: 800/392-3497 Fax: 800/955-6831 Europe, Africa, and Middle East only. For customer orders, contact Customer Service at: + 49 9421-706 0 Fax: + 49 9421-706 265 Other Internatonal locations. For customer orders, Contact Customer Service at: + 1 952 884-4051 Fax: + 1 952 887-9212 For warranty repair or service information, contact the Service Repair department at: 800/685-2606 For technical assistance, contact Technical Support at: 866/78AUDIO Specifications subject to change without notice. EVH-1152D/96 Single 15” Two-Way Coaxial 90° x 60° Full-Range High-Efficiency Loudspeaker System Key Features: • • • • • • • • • DH7N 3” (76 mm) diaphragm, 1.4” (36 mm) exit pure titanium compression driver SMX2151 15” (381 mm) LF transducer with fully symmetric drive Advanced fourth-order crossover network with HF protection Coverage pattern: 90° x 60° Constant DirectivityTM 12” rotatable waveguide 105 dB sensitivity, 138 dB maximum SPL System rating: 500 W continuous, 2000 W peak Active rating: LF 400 W/HF 75 W continuous (1600 W/300 W peak) (28) M10 threaded suspension points PI and FG versions available with gland nut and stainless-steel grille Technical Specifications: Freq. Response1 (-3 dB): 60 Hz - 17 kHz Freq. Range1 (-10 dB): 50 Hz - 20 kHz Rotatable Coverage: 90° x 60° Rec. High-Pass Frequency: 60 Hz Passive Crossover Freq.: 1300 Hz Axial Sensitivity1: 105 dB (1 W/1 m) Max. Calculated SPL1: 138 dB Passive Power Handling2: 500 W continuous, 2000 W peak Impedance: 8 ohms (nominal), 6.0 ohms (min.) LF Transducer - SMX2151, 15” (381 mm) driver LF Axial Sensitivity4: 106 dB (1 W/1 m) LF Max. Calculated SPL: 138 dB LF Power Handling3: 400 W continuous, 1600 W peak LF Impedance: 8 ohms (nominal), 6.1 ohms (min.) HF Transducer - DH7N, 3” (76 mm) diaphragm compression driver HF Axial Sensitivity4: 111 dB (1 W/1 m) HF Max. Calculated SPL: 136 dB HF Power Handling3: 75 W continuous, 300 W peak HF Impedance: 8 ohms (nominal), 6.0 ohms (min.) General Description: The Electro-Voice EVH-1152D/96 is a high-power, two-way horn-loaded coaxial loudspeaker system that can be used in a variety of applications where excellent sound reinforcement, wide bandwidth directivity control, and high efficiency is required in a compact package. The EVH-1152D/96 utilizes the DH7N, a high-output 3” titanium compression driver, coupled to a Constant Directivity™ 90° x 60° waveguide. The SMX2151 15” woofer was developed using FEA optimization for motor, suspension, and electrical design to ensure very low distortion, high efficiency, and maximum intelligibility at high SPL. The crossover uses steep, 24-dB-per-octave slopes with equalization for very smooth response in the vocal range, linear off-axis response, and a protection circuit for long-term reliability. This combination of technologies results in a smooth response to 20 kHz and excellent pattern control down to 500 Hz. The EVH-1152D/96’s features make it ideal for many fixed-install applications. The trapezoidal enclosure is constructed of weather-resistant birch, and coated with EVCoatTM for protection from the elements. For maximum protection against extreme outdoor elements, a fully-weatherized fiberglass version is available. The unique acoustic and rigging design allows for vertical and horizontal clusters to be built using any combination of loudspeakers from the entire EVF and EVH series. With seven horn patterns to choose from, along with an assortment of lowfrequency and subwoofer loudspeakers, you have the tools to maximize flexibility of system design, no matter what the application and budget. The innovative input panel provides a choice of Phoenix-style connector (included in all standard models) or the ability to add a dual NL4-type connector cover plate or gland-nut cover plate (for weatherizing applications). An externally accessible jumper selects passive or active operation. An available 70.7/100-V transformer kit may be easily mounted to the input panel for use in distributed systems. All these features give you the flexibility to address a large range of venues, quickly and precisely supporting customer requirements with fewer items in inventory. Connectors: Dual four-pin 10 AWG Phoenix/Euro Block screw-terminals PI/FG Versions - CDG dual-glandnut input panel cover included Enclosure: 13-ply weather-resistant FG Version - 13-ply weather-resisbirch with EVCoatTM tant birch with fiberglass finish Grille: 16 GA powder-coated galvanneal with rotatable logo PI/FG Versions Stainless steel with hydrophobic cloth Environmental: IEC 60529 IP55 for PI and FG versions Suspension: (28) M10 threaded suspension points Dimensions 30.26” x 30.26” x 26.77” (H x W x D): (768.6 mm x 768.6 mm x 680.1 mm) Weight: 145.5 lb (66.1 kg) net, 160.5 lb (72.9 kg) shipping Half-space measurement. 2 EIA RS-426A, tested for eight hours. 1 3 4 AES 2-1984, tested for eight hours. Arithmetic averages, 300 - 1,300 Hz (LF) and 1,300 - 5,000 Hz (HF). EVH-1152D/96 Loudspeaker System Frequency Response & Impedance: Horizontal Off-Axis Frequency Response: 100 100 100 90 Passive Mode, Half Space Impedance, Passive Mode 20 50 100 1000 10000 90 80 10 80 70 SPL (dB) 1W/1m 110 Impedance (Ohms) 316 SPL (dB) 1W/1m 110 70 3.16 20000 On Axis 20° Horizontal 40° Horizontal 20 50 100 10° Horizontal 30° Horizontal 50° Horizontal 1000 10000 20000 Frequency (Hz) Frequency (Hz) Vertical Off-Axis Frequency Response: 110 SPL (dB) 1W/1m 100 90 80 70 20 50 100 On Axis 10° Vertical 20° Vertical 30° Vertical 1000 10000 20000 Frequency (Hz) Directivity: Horizontal Vertical Directivity Index (DI), dB -6dB Beamwidth (degrees) 360 100 50 20 30 1000 20 100 Directivity Factor (Q) Beamwidth: 10 0 3.6 20 100 1000 Frequency (Hz) Block Diagram (biamp): 10000 20000 10 20 100 1000 Frequency (Hz) Block Diagram (passive): 10000 1 20000 Engineering Data Sheet Polar Plots (1/3 Octave): 400 Hz 500 Hz 630 Hz 1.6 kHz 800 Hz 1 kHz 1.25 kHz 2.5 kHz 3.15 kHz 4 kHz 5 kHz 6.3 kHz 8 kHz 10 kHz 12.5 kHz 16 kHz 20 kHz Horizontal = Black Vertical = Grey 2 kHz Dimension Drawings: End View Front View Side View EVH-1152D/96 Part Numbers • PRD000307-001 EVH-1152D/96-BLK, 90° x 60°, black finish • PRD000307-002 EVH-1152D/96-WHT, 90° x 60°, white finish • PRD000307-003 EVH-1152D/96-PIB, 90° x 60°, black finish, weather resistant • PRD000307-004 EVH-1152D/96-PIW, 90° x 60°, white finish, weather resistant • PRD000307-005 EVH-1152D/96-FGB, 90° x 60°, black finish, weather resistant fiberglass • PRD000307-006 EVH-1152D/96-FGW, 90° x 60°, white finish, weather resistant fiberglass Performance Match • • • • • • • • • • • PRD000303 PRD000304 PRD000305 PRD000306 PRD000308 PRD000300 PRD000302 CPS2.9 120V CPS2.12 120V D170469 D170466 EVH-1152D/43, 40° x 30° coverage EVH-1152D/64, 60° x 40° coverage EVH-1152D/66, 60° x 60° coverage EVH-1152D/94, 90° x 40° coverage EVH-1152D/99, 90° x 90° coverage EVF-2121S, dual 12” bass element EVF-2151D, dual 15” bass element CPS2.9, 120V power amplifier, 2 x 900W CPS2.12, 120V power amplifier, 2 x 1200W CPS4.5, 120V power amplifier, 4 x 500W CPS4.10, 120V power amplifier, 4 x 1000W Electro-Voice 12000 Portland Avenue South, Burnsville, MN 55337 Phone: 952/884-4051, Fax: 952/884-0043 www.electrovoice.com © Bosch Communications Systems Part Number LIT000467096 Rev A 07/2010 Rear View CAUTION This EVH loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the EVF/EVH User Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances. Accessories • • • • • • • • • • • • • • • • ACC000084-000 ACC000085-000 ACC000086-000 ACC000087-000 ACC000089-001 ACC000089-002 ACC000090-001 ACC000090-002 ACC000091-001 ACC000091-002 ACC000092-001 ACC000092-002 ACC000093-001 ACC000093-002 ACC000094-001 ACC000094-002 CDNL4, cover plate, dual NL4 CSG, cover plate, single gland nut CDG, cover plate, dual gland nut TK-150, 70V transformer, 150W HRK-1B, horiz. rigging kit, EVF, black HRK-1W, horiz. rigging kit, EVF, white HRK-2B, horiz. rigging kit, EVF-SUB, black HRK-2W, horiz. rigging kit, EVF-SUB, white HRK-3B, horiz. rigging kit, EVH, black HRK-3W, horiz. rigging kit, EVH, white VRK-1B, vert. rigging kit, EVF, black VRK-1W, vert. rigging kit, EVF, white VRK-2B, vert. rigging kit, EVF-SUB, black VRK-2W, vert. rigging kit, EVF-SUB, white VRK-3B, vert. rigging kit, EVH, black VRK-3W, vert. rigging kit, EVH, white U.S.A. and Canada only. For customer orders, contact Customer Service at: 800/392-3497 Fax: 800/955-6831 Europe, Africa, and Middle East only. For customer orders, contact Customer Service at: + 49 9421-706 0 Fax: + 49 9421-706 265 Other Internatonal locations. For customer orders, Contact Customer Service at: + 1 952 884-4051 Fax: + 1 952 887-9212 For warranty repair or service information, contact the Service Repair department at: 800/685-2606 For technical assistance, contact Technical Support at: 866/78AUDIO Specifications subject to change without notice. EVH-1152D/99 Single 15” Two-Way Coaxial 90° x 90° Full-Range High-Efficiency Loudspeaker System Key Features: • • • • • • • • • DH7N 3” (76 mm) diaphragm, 1.4” (36 mm) exit pure titanium compression driver SMX2151 15” (381 mm) LF transducer with fully symmetric drive Advanced fourth-order crossover network with HF protection Coverage pattern: 90° x 90° Constant DirectivityTM 12” rotatable waveguide 104 dB sensitivity, 137 dB maximum SPL System rating: 500 W continuous, 2000 W peak Active rating: LF 400 W/HF 75 W continuous (1600 W/300 W peak) (28) M10 threaded suspension points PI and FG versions available with gland nut and stainless-steel grille Technical Specifications: Freq. Response1 (-3 dB): 60 Hz - 17 kHz Freq. Range1 (-10 dB): 50 Hz - 20 kHz Rotatable Coverage: 90° x 90° Rec. High-Pass Frequency: 60 Hz Passive Crossover Freq.: 1300 Hz Axial Sensitivity1: 104 dB (1 W/1 m) Max. Calculated SPL1: 137 dB Passive Power Handling2: 500 W continuous, 2000 W peak Impedance: 8 ohms (nominal), 6.0 ohms (min.) LF Transducer - SMX2151, 15” (381 mm) driver LF Axial Sensitivity4: 106 dB (1 W/1 m) LF Max. Calculated SPL: 138 dB LF Power Handling3: 400 W continuous, 1600 W peak LF Impedance: 8 ohms (nominal), 6.1 ohms (min.) HF Transducer - DH7N, 3” (76 mm) diaphragm compression driver HF Axial Sensitivity4: 110 dB (1 W/1 m) HF Max. Calculated SPL: 135 dB HF Power Handling3: 75 W continuous, 300 W peak HF Impedance: 8 ohms (nominal), 6.0 ohms (min.) General Description: The Electro-Voice EVH-1152D/99 is a high-power, two-way horn-loaded coaxial loudspeaker system that can be used in a variety of applications where excellent sound reinforcement, wide bandwidth directivity control, and high efficiency is required in a compact package. The EVH-1152D/99 utilizes the DH7N, a high-output 3” titanium compression driver, coupled to a Constant Directivity™ 90° x 90° waveguide. The SMX2151 15” woofer was developed using FEA optimization for motor, suspension, and electrical design to ensure very low distortion, high efficiency, and maximum intelligibility at high SPL. The crossover uses steep, 24-dB-per-octave slopes with equalization for very smooth response in the vocal range, linear off-axis response, and a protection circuit for long-term reliability. This combination of technologies results in a smooth response to 20 kHz and excellent pattern control down to 500 Hz. The EVH-1152D/99’s features make it ideal for many fixed-install applications. The trapezoidal enclosure is constructed of weather-resistant birch, and coated with EVCoatTM for protection from the elements. For maximum protection against extreme outdoor elements, a fully-weatherized fiberglass version is available. The unique acoustic and rigging design allows for vertical and horizontal clusters to be built using any combination of loudspeakers from the entire EVF and EVH series. With seven horn patterns to choose from, along with an assortment of lowfrequency and subwoofer loudspeakers, you have the tools to maximize flexibility of system design, no matter what the application and budget. The innovative input panel provides a choice of Phoenix-style connector (included in all standard models) or the ability to add a dual NL4-type connector cover plate or gland-nut cover plate (for weatherizing applications). An externally accessible jumper selects passive or active operation. An available 70.7/100-V transformer kit may be easily mounted to the input panel for use in distributed systems. All these features give you the flexibility to address a large range of venues, quickly and precisely supporting customer requirements with fewer items in inventory. Connectors: Dual four-pin 10 AWG Phoenix/Euro Block screw-terminals PI/FG Versions - CDG dual-glandnut input panel cover included Enclosure: 13-ply weather-resistant FG Version - 13-ply weather-resisbirch with EVCoatTM tant birch with fiberglass finish Grille: 16 GA powder-coated galvanneal with rotatable logo PI/FG Versions Stainless steel with hydrophobic cloth Environmental: IEC 60529 IP55 for PI and FG versions Suspension: (28) M10 threaded suspension points Dimensions 30.26” x 30.26” x 26.77” (H x W x D): (768.6 mm x 768.6 mm x 680.1 mm) Weight: 145.5 lb (66.1 kg) net, 160.5 lb (72.9 kg) shipping Half-space measurement. 2 EIA RS-426A, tested for eight hours. 1 AES 2-1984, tested for eight hours. Arithmetic averages, 300 - 1,300 Hz (LF) and 1,300 - 5,000 Hz (HF). 3 4 EVH-1152D/99 Loudspeaker System 100 100 Impedance (Ohms) 316 SPL (dB) 1W/1m 110 90 80 70 Horizontal Off-Axis Frequency Response: 110 100 SPL (dB) 1W/1m Frequency Response & Impedance: 80 10 Passive Mode, Half Space Impedance, Passive Mode 20 50 100 1000 10000 90 70 3.16 20000 On Axis 20° Horizontal 40° Horizontal 20 50 100 10° Horizontal 30° Horizontal 50° Horizontal 1000 10000 20000 Frequency (Hz) Frequency (Hz) Vertical Off-Axis Frequency Response: 110 SPL (dB) 1W/1m 100 90 80 70 On Axis 20° Vertical 40° Vertical 20 50 100 1000 10° Vertical 30° Vertical 10000 20000 Frequency (Hz) Directivity: Horizontal Vertical Directivity Index (DI), dB -6dB Beamwidth (degrees) 360 100 50 20 30 1000 20 100 Directivity Factor (Q) Beamwidth: 10 0 3.6 20 100 1000 Frequency (Hz) Block Diagram (biamp): 10000 20000 10 20 100 1000 Frequency (Hz) Block Diagram (passive): 10000 1 20000 Engineering Data Sheet Polar Plots (1/3 Octave): 400 Hz 500 Hz 630 Hz 1.6 kHz 800 Hz 1 kHz 1.25 kHz 2.5 kHz 3.15 kHz 4 kHz 5 kHz 6.3 kHz 8 kHz 10 kHz 12.5 kHz 16 kHz 20 kHz Horizontal = Black Vertical = Grey 2 kHz Dimension Drawings: End View Front View Side View EVH-1152D/99 Product Descriptions • • • • • EVH-1152D/99-BLK, 90° x 90°, Black Finish EVH-1152D/99-WHT, 90° x 90°, White Finish EVH-1152D/99-PIB, 90° x 90°, Black Finish, Weather Resistant EVH-1152D/99-PIW, 90° x 90°, White Finish, Weather Resistant EVH-1152D/99-FGB, 90° x 90°, Black Finish, Weather Resistant Fiberglass • EVH-1152D/99-FGW, 90° x 90°, White Finish, Weather Resistant Fiberglass Performance Match • • • • • • • • • • • EVH-1152D/43, 40° x 30° Coverage EVH-1152D/64, 60° x 40° Coverage EVH-1152D/66, 60° x 60° Coverage EVH-1152D/94, 90° x 40° Coverage EVH-1152D/96, 90° x 60° Coverage EVF-2121S, Dual 12” Bass Element EVF-2151D, Dual 15” Bass Element CPS2.9, 120V Power Amplifier, 2 x 900W CPS2.12, 120V Power Amplifier, 2 x 1200W CPS4.5, 120V Power Amplifier, 4 x 500W CPS4.10, 120V Power Amplifier, 4 x 1000W Electro-Voice 12000 Portland Avenue South, Burnsville, MN 55337 Phone: 952/884-4051, Fax: 952/884-0043 www.electrovoice.com © Bosch Communications Systems Part Number F.01U.196.275 Rev 02 05/2011 Rear View CAUTION This EVH loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the EVF/EVH User Manual and possible manual update notices. This system should be suspended with certified rigging hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances. Accessories • • • • • • • • • • • • CDNL4, Cover Plate, Dual NL4 CSG, Cover Plate, Single Gland Nut CDG, Cover Plate, Dual Gland Nut TK-150, 70V Transformer, 150W HRK-2B, Horiz. Rigging Kit, EVF-SUB, Black HRK-2W, Horiz. Rigging Kit, EVF-SUB, White HRK-3B, Horiz. Rigging Kit, EVH, Black HRK-3W, Horiz. Rigging Kit, EVH, White VRK-2B, Vert. Rigging Kit, EVF-SUB, Black VRK-2W, Vert. Rigging Kit, EVF-SUB, White VRK-3B, Vert. Rigging Kit, EVH, Black VRK-3W, Vert. Rigging Kit, EVH, White U.S.A. and Canada only. For customer orders, contact Customer Service at: 800/392-3497 Fax: 800/955-6831 Europe, Africa, and Middle East only. For customer orders, contact Customer Service at: + 49 9421-706 0 Fax: + 49 9421-706 265 Other Internatonal locations. For customer orders, Contact Customer Service at: + 1 952 884-4051 Fax: + 1 952 887-9212 For warranty repair or service information, contact the Service Repair department at: 800/685-2606 For technical assistance, contact Technical Support at: 866/78AUDIO Specifications subject to change without notice.