Ex1000 Intelligent Motorized Cameras

Transcript

THE ULTIMATE OUTDOOR SURVEILLANCE MACHINES THE EX1000 SERIES MODELS ARE IDEAL FORTRAFFIC CONTROL, SURVEILLANCE OF SEA & AIRPORTS, OIL FIELDS & REFINERIES, MILITARY & POLICE, SPORT STADIUMS & ARENAS, TOWN & CITY CENTERS, BUS & RAIL STATIONS AND OTHER HIGH SECURITY OUTDOOR INSTALLATIONS, FEATURING: ALL WEATHER, LIGHTWEIGHT (LESS THAN 6 KG) HIGH IMPACT POLYCARBONATE BODY 360 UNOBSTRUCTED ROTATION USING HEAVY DUTY LONG LIFE SLIP RINGS REMOTE SETTING OF AUTO PANNING ANGLE AND SPEED BREAK AND CLUTCH PROTECTED PAN AND TILT VARIABLE SPEED CONTROL FOR ALL MOTORIZED FUNCTIONS (PAN, TILT, ZOOM AND FOCUS) UP TO 99 PRESET POSITIONS ENTRY AND RECALL UP TO 16 ALARMS +1 (LOCAL ALARM) PRESET POSITIONS WITH HIGH SPEED ALARM RECALL ENVIRONMENTAL AND AIR FLOW CONTROL FOR INTERNAL AIR CIRCULATION, VENT, HEAT, AND DRY SENSORS FOR CONTROL OF DEW, TEMP., PAN, TILT, ZOOM, FOCUS POSITIONS, WIPER PARKING & MORE DUAL FAN WITH REAR MOTORIZED AIR FLOW DUCT AND FRONT MOTORIZED AIR SHUTTER LINEAR RECIPROCAL WIPER WITH AUTO PARKING FRONT PANE WASHER SYSTEM WITH WATER DELIVERY VIA MAIN SHAFT CONTROLS AND EXT. SYNC VIA SINGLE COAX, OR RS422 CONTROLS VIA TWISTED PAIR OR FIBER OPTIC CABLES EMXC1000 (COLOR) AND EMX1000 (B/W) CAMERA MODULES The EMXC1000 and the EMX1000 offer outstanding performance under low-light or against bright light, with low noise and high resolution Improved video processing along with video enhancement and a low noise efficient AGC amp., both camera modules with high density CCD imagers of 430K pixels, produce superior quality pictures. Dynamic color control using through the lens auto white balance circuitry depict exceptional natural colors regardless of scene content and against a wide range of illuminator’s color temperature permitting unrestrained outdoor color surveillance. The B/W CCD’s extended IR spectrum makes the B/W module suitable* for total darkness surveillance when used against IR illuminators. Perfect color reproduction for varied color temperature range (2856 K~7000 K). Continuous self-adjusting auto white balance, using through the lens detection. High resolution of 570 lines (B/W) OR 470 lines (color). Excellent S/N better than 52dB (B/W) OR 47dB (color) AGC off. Superior light handling capabilities, from light levels of 0.1 lux (B/W) or 1 lux (color) to super bright of 1~100,000 lux. Immunity to vibration and magnetic fields with a wide operating ambient temperature (-20 C~ +55 C). Highly reliable (MTBF 600,000 Hr.) *For IR surveillance the EMX1000 module can be supplied with the IR cut filter removed, specify when ordering. EMMC1000/EMMC1020 Remote setting of fast and slow shutter speed. The shutter mode of the EMX1000 and EMXC1000 camera modules can be remotely set when used with EMMC1000 (B/W) or EMMC1020 (color) memory and control modules. While fast shutter speed of 1/100 sec. ~ 1/10,000 sec. can be used for observing fast moving objects under highly illuminated/bright areas, the slow shutter speed of 1/25 sec. ~10 sec. increases the camera’s sensitivity several hundred times, allowing observation of stationary objects under ecxtreme low light conditions, such sd moonlight. THE PIP CAMERA MODULE EMX2 Small size, high sensitivity 1/2” B/W camera module with built-in wide angle lens. The EMX2 is an optional “range finder” B/W mini camera module, providing together with the EMPP1000 module, a wide angle “picture in picture” for displaying the camera’s entire field of view, thereby enabling the observer “easy reognition” of the camera positioning, particularly whenever the zoom lens is set to telephoto. The EMX2 module with its built-in 10mm F1.4 auto iris lens offers exceptionally crisp pictures which can be displayed in any of the four corners of the monitor screen or recalled into a full screen display. Mini, unobtrusive module size. Excellent light handling capabilities, from low light levels of 0.3 lux to 100,000 lux. Standard resolution of 430 lines. Excellent S/N better than 50dB. Highly reliable (MTBF 600,000 HR.) Low power consumption (150mA max.) EMPP1000 PIP module EMX2 PIP camera module BUILT-IN MOTORIZED PANNING WITH POSITION SENSORS 360 continuous rotation panning PANNING MOTOR DRIVE PCB Precise and efficient mechanism assembled into the camera pedestal, the panning system incorporates the main camera shaft mounted on dual ball bearings, the main roller, the gear assembly and a brushless, servo motor. Employing ball bearings throughout the gear assembly - two for each individual gear - ensures long gear life, complementing the more than 30,000 hour brushlesscoreless motor. MOTOR CLUTCH ASSY 99 panning preser and last positions Reference voltage generated by the dual long life (5 million revolutions) sensors/potentiometers mounted inside the slip ring assembly provide for the 99 preset and last positions, throughout the 360 continuous rotation. Permitting fastest recall from either left or right direction, whichever is closer to the recalled preset position. Remote setting of panning speed PANNING GEAR ASSY MAIN SHAFT The precision panning speed governed by the servo motor circuitry can be remotely set to any of the 8 step speed, whereby each of the speed steps is governed by the servo circuitry from 6 /sec. to 35 /sec. POWER SUPPLY PCB AUTO PANNING Remote setting of auto panning angle The EX1000 series models offer dual auto panning modes, one in a continuous 360 surround rotation at 8 speeds, in both clockwise or counterlockwise directions. The other is pendulum auto panning movement, remotely set via panning keys to a precise angle, covering from 7 up to 360 in any direction, at a selected speed. 360 to left Simple removal of assemblies for prompt servicing Pendulum at remotely set panning angle 360 to right The panning assembly is easily accessible through the removal of the side arm cover and once released the panning gear assy in itself is serviceable whereby, each and every part of the gear assembly is replaceable, requiring no special mechanical tools or jigs for reassembly. 360 ROTATION WITH HEAVY DUTY SLIP-RINGS Noiseless slip-rings inside the camera shaft Mounted inside the main camera shaft is an innovative slip-ring assembly consisting of 13 rings with four contacts per ring, guaranteeing flawless continuity and no noise. The ring and contacts are made of heat treated phosphor bronze and coated with very hard alloy to offer 0.1m resistance and 250VAC/2A or 24VDC/A contact ratings. The slip-ring body made of high impact polycarbonate and pivoted on dual ball bearings also contains the dual panning sensor assembly and a swivel water joint for delivering water to the pane washer. BUILT-IN MOTORIZED TILTING AND POSITION SENSOR 180 of smooth tilting Efficient mechanism assembled into the camera case consists of the main camera case mounted on dual ball bearings, the tilting roller, the tilting gear assembly and a brushless servo motor. Similar to the panning gear assembly, the tilting gear assembly employs ball bearings throughout - two for each individual gear - ensuring long gear life. MAIN TILTING GEAR CLUTCH ASSY TILT GEAR ASSY 99 tilting preset and last position The tilting position sensor mounted inside the camera case generates accurate reference voltage for the 99 preset or the last tilting positions, throughout the 180 tilting rotation. Remote setting of tilting speed Similar to the panning speed control, the precision speed governed by the servo motor circuitry can be remotely set to any of the 8 speeds from 6 /sec. to 35 /sec.. TILT MOTOR Servicing with ease Similar to all other EX1000 assemblies the tilting gear assy can be easily removed and serviced. Each and every part of the tilting gear assembly can be replaced with no special mechanical tools or jigs for reassembly. BUILT-IN MOTORIZED ZOOM LENS WITH MOTORIZED AUTO IRIS AND POSITION SENSORS A choice of 12X or 20X multi-coated, highly efficient motorized zoom lenses The zoom lens assy incorporates the zoom and focus motors with gear/clutch assembly and the zoom/focus position sensors with gear assembly. Long life moving coil (galvanometer) auto iris The “moving coil”, ND filtered auto iris assures long life with MTBF of more than 600,000 hours and response time of less than 1 sec. The auto iris control system provides for manual override of the iris for operating the camera under atypical lighting conditions. 99 zoom & focus presets and last position recall Similar to the panning and tilting sensors, the zoom and focus position sensors enable remote entering/recalling of 99 preset and “last” positions into and from the memory circuit. Remote setting of zoom and focus speed Consistent with all other motorized functions of the EX1000, the zoom and focus speed are adjustable and can be remotely set to any of eight speed levels. Easy access to all parts simplifies servicing The lens motors, gear assemblies and sensors are serviceable and similar to other major components of the EX1000, permitting replacement of all major parts and assemblies. ALL WEATHER CAMERA CASE WITH BUILT-IN ENVIRONMENTAL SENSING PROTECTION AND AUTO SELF CONTROL SYSTEM Engineered and constructed to last Outdoor, heavy duty, weatherproof camera case constructed of high impact polycarbonate, using all weather assemblies, parts and materials. Insulated integral cover/sunshield POLYURETHANE FROM INSULATION SILICON RUBBER The all weather resistant cover/sunshield assembly made of laminated stainless steel on top of a high impact polycarbonate body filled with polyurethane foam and surrounded by a silicon rubber “O” ring for perfectly sealing the camera case. Condensation repellent front glass pane An anti fogging coated glass with condensation repellent film, assures clear vision through the front pane. DEW SENSOR All environment support system The environment support system sonsists of two brushless servo fans, rear air duct with motorized airflow vanes and filter, front air vent with motorized shutter, high efficiency ceramic heater, dew sensor, high and low temperature sensors. Front shutter Rear air duct Close VANE Vent VANE Internal air circulation Fresh air Heat, cool and dry programs The programmed control circuit connected to the dew and the temperature sensors coordinates the rear vanes, the front vent, the fans and the heater to operate in four modes as follows: Internal air circulation Heat (-35 C~10 C) Dry 1 (10 C~40 C) Fresh air & vent Dry 2 (over 35 C) Dry 1 (over 40 C) Elbex commitment to simple service and maintenance All the environments support components and assemblies such as motors, fans, heater and sensors can be easily replaced and serviced. The air filter is freely accessible for cleaning or replacement through the rear of the air duct. BUILT-IN RECIPROCAL LINEAR WIPER WITH PARKING SENSOR Chain reciprocal movement mechanism Travelling back and forth and wiping the entire front pane, the wiper’s slim mechanism is embedded into the body of the camera case. Long life, constant load and reduced noise Though the wiper features horizontal reciprocal movement, the wiper motor rotates only in one direction with a smooth constant load. The one direction rotation eliminates the startreverse electrical and mechanical noise and extends the motor’s life. Auto parking and locking system A parking sensor (photo interupter) of the wiper mechanism along with the auto parking control system locks the wiper in its parking position to the right, behind the front shield and outside the visual angle of the lens. The auto parking control system will also park the wiper when the power line is swithced on or when power is restored after random power failure. BUILT-IN WASHER Waher fluid delivery through the main shaft The washer system consists of a high pressure water nozzle, a swivel water joint, flexible water hoses, fittings and control circuitry. Unobstructed movement with built-in swivel water joint The swivel water joint located inside the slip ring assembly and mounted in the main shaft does not obstruct the panning or tilting movements. Similarly the water flows unobstructed through the shaft, the flexible hoses and to the high pressure nozzle. Simple to connect and install The water inlet fitting located at the bottom center of the main shaft is accessible through the pole mount for easy connections. A connector located in the pole mount provides dry contacts (250V: 2A) to operate the washer pump or an electric water valve. BUILT-IN HEATER SYSTEM High efficiency ceramic heater Mounted on an efficient heat sink, the heater assembly incorporates two ceramic heaters and a brushless fan, promptly circulating hot dried air to maintain equal temperature to all of the camera’s inner assemblies and the lens. Simplified service and maintenance The wiper and the washer system are serviceable, permitting easy replacement of parts and assemblies. The wiper blade is freely accessible and can be replaced by simple removal of the front shield. INTEGRATED PCBs WITH ENVIRONMENTAL, MOTORS CONTROL, POWER SUPPLY, CPU & PIP The main PCB contains all the camera system interconnections and comprises the temperature sensors, the heater control, the rear/front fan and the rear/front duct motor control. The main PCB further comprises the pan, tilt, zoom and focus control circuits along with the tilt motor drive circuit. Several types of main PCB are supplied with the camera in accordance with the camera controls and features. The basic main PCB is for (multi-core cable) control, having a single control wire for each motorized function, whereby applying high or low logic levels to the control wires will operate the motors in reciprocal directions, wherein; high is +15V and low is ground. The simplicity of the “high-open-low” control system to operate the motors provides for custom made controls, using three position level switchers: Main PCB FAR FOCUS ZOOM NEAR +15V WIDE TILT N E TELE FO C U S LI UP RIGHT PAN O M LI N E DOWN O Power supply PCB Z ON IL T LI N E LEFT E T AUXILIARY LI G IN OFF N N R Y OPEN PA +15V X RIGHT UP WIDE FAR OFF U LEFT DOWN TELE NEAR ON A PAN TILT ZOOM FOCUS AUX. IL IA LINE Mounted in the side arm, the power PCB, fed by the power transformer, rectifies and supplies 15V DC regulated (noise free and ripple free) to the entire camera system. N TRUTH TABLE INPUT OFF Current: 3mA max Panning motor drive PCB The brushless servo panning motor is driven by a servo circuit mounted in the side arm. The CPU, PIP, memory and shutter control modules All EX1000 series models with preset, controlled via coax or by RS422 (via twisted pair) employs main PCB to accommodate the CPU module EMDU1000. The EMDU1000 also controls the optional EMMC1000 series modules for setting the shutter speed, which also comprises a video memory for supporting the long time exposure (1/25 sec. ~ 10 sec.) and the PIP module EMPP1000. EMPP1000 PIP module EMDU1000 CPU module The PIP module multiplexes the PIP camera module signals into the video output to display a small sized picture into any of the four corners of the main picture display. The PIP module can be set to display the PIP picture on a full screen or reverse its position to become the main picture, while the main camera picture becomes the PIP. The EMPP1000 module plugs into the main PCB, allowing easy retrieval for adjustment and servicing. The CPU module consists of a micro processor, operational memories, circuit and an array of drivers, converters and memory backup circuits. The module plugs into the main PCB and hooks up to the sensors and interconnection harnesses. The CPU module controls the speed and operates the pan, tilt, zoom, focus and iris; preset positioning, alarm, local alarm preset and annunciation; heater, wiper, washer, fans, rear and front ducts; auto panning angle and speed; and many more setup functions of the camera module. EMMC1000 video memory and shutter modules The four models EMMC1000, EMMC1000C (CCIR), EMMC1020 and EMMC1020P (PAL) provide the video memory needed for long exposure of 1/25 sec. to 10 sec.. The modules also control the fast shutter speed (short exposure) of 1/100 sec. to 1/ 10,000 sec. and incorporate the PIP circuit for multiplexing the EMX2 camera module’s signal into the video output. Module selection chart SYSTEM MODE B/W EIA CCIR COLOR NTSC EIA FAST SHUTTER SPEED FAST-SLOW SHUTTER SPEED FAST-SLOW SHUTTER SPEED + PIP (B/W) EMDU1000 EMDU1000 EMMC1000 EMDU1000 EMMC1000 EMX2 EMDU1000 EMDU1000 EMMC1000 EMDU1000 EMMC1000 EMX2C EMDU1000 EMDU1000 EMMC1020 EMDU1000 EMMC1020 EMX2 EMDU1000 EMDU1000 EMMC1020P EMDU1000 EMMC1020P EMX2C PIP ONLY (B/W) EMDU1000 EMPP1000 EMX2 EMDU1000 EMPP1000C EMX2C EMDU1000 EMPP1000 EMX2 EMDU1000 EMPP1000C EMX2C Simple removal of all PCBs and modules for prompt servicing Elbex commitment to simplified service assures that all PCB and module assemblies are easily accessible and removable, requiring no special tools or jigs. CAMERA CONTROL AND SYSTEM MANAGEMENT EQUIPMENT Three way switcher/controller, and RS422 for controlling the EX1000 along with other cameras via coax, twisted pair or multi-core cables. Amazingly powerful yet simple to operate, the EXS126 and EXS136 switcher/controller models also offer three way operation, via front panel keys, hand held IR remote control or via PC using software program. The EXS126 and EXS136 further offer. 8 inputs/2 outputs manual/sequential switcher. Remote pan, tilt, zoom and focus control. Remote setting of auto panning angle and speed. Remote iris control (EXS136 only). Enter/recall of 8 preset and last positions. Enter/recall of alarm preset positions. Independent sequence time setting for each camera ()1~99 sec.) Alarm homing and multi alarm sequence. Built-in sync. generator. Cascaded RS422 for larger systems and Built-in for displaying a camera’s I.D.. EXS136 : Windows based system control and management, offering convenience of a keyboard, mouse or touch screen. Easy to install, setup and operate the features: Individual control of cameras, switchers, controllers and VCR’s. Slavos and comprehensive control of the entire system. Instant monitoring of alarms in accordance with user programmed events. Preprogrammed equipment responses for multiple or single alarms. User friendly messages and on-line help. EXS126 (station 005) Exit Setting... AUTO AUTO/PRESET 1 2 3 4 5 6 7 8 6 7 8 VTR MANUAL SELECT 1 2 3 4 5 LAST I.D. POSITION SEQ. TIME PAN/TILT ALARM ZOOM FOCUS WIDE FAR AUTO PAN AUX WIPER PRESET TELE NEAR POWER SWITCHER EXS126 The EXS126 panel as seen in - Elbex offers a wide range of equipment to remotely control the camera’s pan, tilt, zoom, focus and auxiliary via multi core cables. The include manual or auto/manual switchers, B/W or color monitors with built-in switchers and matrix switchers with IR remote controls. Manual audio-video switchers with pan, tilt, zoom, auxiliary controls and remote setting of panning speed. 142 122 125 145 EXS145 4 camera inputs 14" monitor 4 camera inputs Q R S T 5 U 6 V 7 W 8 X EXSQ9305 8 camera inputs V ID IN EO N A V M A E D IN 24 P JA R V ID O E U O T ETC35:24V AC ETC35-120: 100~120V AC ETC35-120: 200~240V AC IN 4 N D 3 G 2 ET C 61 1 CO NV ER TE R EXM1495 A C 15 15 V V ETC35 series three telemetry converter models provide simple interfacing of commonly used telemetry site receivers with Elbex standard pan, tilt, zoom and focus controls. T S U R O EXX9205 matrix switcher (8x4) with built-in F ext. sync gen. and pan, tilt, zoom and focus control via IR remote (from 4 locations) or front pnnel control. N D 14" B/W monitor with audio and built-in auto homing sequential/ manual switcher and pan, tilt, zoom & focus controls. EXS125 8 camera inputs G EXS122 8 camera inputs 42 2 R TE S 42 LE 2 MET RY EXS142 4 camera inputs INTEGRATED OUTDOOR POLE MOUNT Heavy duty pole mount, made of all weather Constructed of cast aluminum base with polycarbonate and stainless steel enclosure, the heavy duty camera mount contains the camera’s power line terminals, fuses, the control wiring terminals and the camera system connectors. The mount further includes the water supply inlet, a control circuit for the water pump and the water pump’s (or an electric water valve’s) connection terminals. A pole mount is supplied as standard with the different EX1000 camera models in accordance with the camera functions, power line and accessories used. Electrical junction box within the mount simplifies installation and maintenance. The camera power, controls and video connectors are located inside the mount and are accessible through the mount’s front cover. The BNC, 8 pin DIN and PCB plugs offer simplified and convenient hook up or removal of the camera. Screw terminals offer simple hook up of the installation cables which can be inserted through the base or by using locally procured outdoor cable bushings, mounted onto the side cable duct. The mount’s terminals and connectors EMS1000 pole mount BNC EMW1000/EMW1010 wall mount adaptors (optional). Non rusting stainless steel adaptor for mounting the camera with its pole mount on walls or other vertical structures. DIN Lightning and surge protection with builtin gas arrestor and solid body grounding. The camera power, controls and video connectors are located inside the mount and are accessible through the mount’s front cover. The BNC, 8 pin DIN and PCB plugs offer simplified and convenient hook up or removal of the camera. Screw terminals offer simple hook up of the installation cables which can be inserted through the base or by using locally procured outdoor cable bushings, mounted onto the side cable duct. EMW1000 Wall mount adaptor Optional water pump EXWP1000 The optional water pump offer 1.5 liter container in stainless steel enclosure, providing high pressure pumping power for feeding washer fluid or water for up to 5m. (16ft) height. Specify 24V, 120V or 230V when ordering. The pole mount easy selection chart With a total twelve models, the pole mounts differ by their power transformer of 24V AC, 100120V AC or 200-240 V AC; Control method using or /RS422; and the use of water pump control connections. Refer to the chart below. POWER/WATER SUPPLY CONTROL METHOD MULTI CORE CABLE VIA COAX/TWISTED PAIR EMW1010 Wall, corner or mid pole mounting adaptor WITHOUT WATER SUPPLY WITH WATER SUPPLY CONNECTIONS POWER LINE (ALL 50/60Hz) 24V AC EMS1000 EMS1010 100-120V(U) EMS1000U EMS1010U 200-240V(E) EMS1000E EMS1010E 24V AC EMS1006 EMS1016 100-120V(U) EMS1006U EMS1016U 200-240V(E) EMS1006E EMS1016E Total service concept applies to mounts as well The mounts like all the other camera’s assemblies are servicable, permitting simple removal and removal and replacement of power trans, fuses and all other major parts. SPECIFICATIONS Pick-up Device : 1/2" interline transfer CCD Picture Elements (Pixels) : PAL 438K (752H X 582V) : NTSC 380K (768H X 494V) Horizontal Resolution : 470 TVL (color); 570 TVL (B/W) Vertical Resolution : 440 (PAL); 375 (NTSC) TVL Amplitude Response : 50% at 340H. TVL (color) : 50% at 400H. TVL (B/W) Bandwidth : 8MHz 3dB Video Output : 1.0V p-p/75 S/N Ratio : Better than 47dB (color) : Better than 52dB (AGC off) (B/W) AGC : Up to 32dB gain AGC Off Level : 10~30 Lux (color) : 3~4 Lux (B/W) Usable Sensitivity : Better than 1 Lux (color) : Better than 0.1 Lux (B/W) White Balance : Automatic trace via image signal Light Control Range : 1 ~ 100,000 Lux (color) : 0.1 ~ 100,000 Lux (B/W) Infra-Red Extended Range : Up to 1050nm (without IR cut filter) (B/W) Scanning System - PAL/CCIR : 625 lines, 50 vertical fields NTSC/EIA : 525 lines, 59.94 vertical fields Sync. System : 2:1 interlaced EIA (RS 170) or CCIR Geometric Linearity : No geometric distortion Ext. Sync : 8V p-p via video coax cable LENS SYSTEM Lens System 12 x Zoom : 10.5mm~126mm; F1.6 with ND and IR cut filter (B/W) or with optical quartz LPF coated IR cut filter (color) Lens System 20 x Zoom : 10mm~200mm; F2.5 with ND and IR cut filter (B/W) or with optical quartz LPF coated IR cut filter (color) Auto Iris Delay : Less than 1 second Motorized Zooming Speed : (12x) 15 sec. (average); (20x) 4 sec. (average) Zoom Preset Accuracy : 3 Motorized Focus Speed : 20 sec. (12x) average; 4 sec. (20x) average Focus Preset Accuracy : 3 Zoom/Focus Preset Sensor : Long life potentiometer (5x10 ) rotations 6 PRESET MEMORY & CONTROL PAN & TILT Panning Motor Panning Angle Panning Speed Panning Preset Accuracy Tilting Motor Tilting Angle Tilting Speed Tilting Preset Accuracy Pan/Tilt Preset Sensors : : : : : : : : : 12V DC Brushless, servo (30,000hr.) 360 continuous 6 /sec.~30 /sec. adjustable in 8 steps 1.5 12V DC Brushless, servo (30,000hr.) 90 6 /sec.~30 /sec. adjustable in 8 steps 1.5 Long life (5 x 10 revolutions) 6 Preset Position & Memory Position Entry and Recall Pan/Tilt Speed Memory Pan/Tilt Speed Entry Speed Reentry Limitation Alarm Preset Position Alarm Preset Recall Speed Local Alarm Memory Back-up : : : : : : : : : Up to 99 + last (P, T, Z, F) Remote via coax or RS422 8 speeds, user selectable Remote via coax or RS422 None; Freely entered 16 positions, user selectable Fixed at high speed Dry relay contacts More than 30 days ENVIRONMENTAL Camera I.D. : : : Bit Width : Bit Level High : Bit Level Low : Pulse Level : Pulse Pedestal : I.D. Control Signal Transmission : Control Signal Code : Camera Access Code : Camera Diagnostic Code : 001~999 selectable via DIP switch 16 bit code transmitted during single horizontal line (H12 1 line) of every field. 3.2 sec. Pulse width 0.8 sec. 5% (25% of bit width) Pulse width 2.4 sec. 5% (75% of bit width) 0.7V p-p/75 0.3V p-p/75 Via coax, twisted pair, fiber optics or any other RS422 transmission medium 3 bit key followed by 3 bit 4 levels access - 2 bit code 3 bit key followed by 4 bit Rear Fan Front Fan Rear Duct Motor Front Shutter Motor Heater : : : : : Heater Saturated Temp. Heater Operating Voltage Wiper Motor Wiper Speed Wiper Parking Sensor Operating Temperature Relative Humifity : : : : : : : POWER, MEASUREMENT & WEIGHT Camera Operating Voltage Power Consumption Heater Power Dimensions Weight  Specifications and dimensions subject to change without notice. 80mm, 12V DC, brushless 60mm, 12V DC, brushless 6 V DC, 5 slots 6 V DC, 5 slots Dual posistor/ceramic heater, 40W~100W self adjustable 260 C (measured on element) 100V AC 50/60Hz 12V DC, coreless, (7,000 hr.) 3 sec./120mm (average) Photo interrupter -35 C~+50 C Up to 100% : : : : : 24V AC or standard power line 30W (without heater) 100 V; 0.15A~1A AC 50/60Hz Refer to illustrations Approx. 9kg (lens included) EX1000 INTELLIGENT MOTORIZED CAMERAS MAJOR OPERATING COMPONENTS (FRONT VIEW) (SIDE VIEW) 360mm 360mm POLE MOUNT MOUNTING HOLES 175mm INSULATED COVER WATER NOZZLE (TOP VIEW) WIPER 485mm 210mm FRONT AIR DUCT REAR AIR DUCT 210mm SIDE ARM PANNING GEAR MECHANISM 245mm PEDESTAL POWER TRANS 210mm POLE MOUNT MODELS SELECTION CHART 200-240V AC E EX1060 EX1061 EX1062 EX1063 EX1064 EX1065 EX1066 EX1067 EX1068 EX1069 EX1070 EX1071 EX1072 EX1073 EX1074 EX1075 EX1076 EX1077 EX1078 EX1079 MOUNT 100-120V AC U EX1040 EX1041 EX1042 EX1043 EX1044 EX1045 EX1046 EX1047 EX1048 EX1049 EX1050 EX1051 EX1052 EX1053 EX1054 EX1055 EX1056 EX1057 EX1058 EX1059 PRESET/ ALARM EX1020 EX1021 EX1022 EX1023 EX1024 EX1025 EX1026 EX1027 EX1028 EX1020 EX1030 EX1031 EX1032 EX1033 EX1034 EX1035 EX1036 EX1037 EX1038 EX1039 AUTO PAN EX1000 EX1001 EX1002 EX1003 EX1004 EX1005 EX1006 EX1007 EX1008 EX1009 EX1010 EX1011 EX1012 EX1013 EX1014 EX1015 EX1016 EX1017 EX1018 EX1019 P.T.Z. & F. COLOR POSITIONING AIR FLOW SYSTEM B/W WASHER COLOR WIPER B/W ENVIRONMENT HEATER/DEW SYSTEM ZOOM LENS 20X 24V AC VIA COAX/RS422 MULTICORE CABLE CONTROL METHOD ZOOM LENS 12X EMS1000 EMS1000 EMS1000 EMS1000 EMS1000 EMS1000 EMS1006 EMS1000 EMS1006 EMS1006 EMS1010 EMS1010 EMS1010 EMS1010 EMS1010 EMS1010 EMS1016 EMS1010 EMS1016 EMS1016 EMS1000U EMS1000U EMS1000U EMS1000U EMS1000U EMS1000U EMS1006U EMS1000U EMS1006U EMS1006U EMS1010U EMS1010U EMS1010U EMS1010U EMS1010U EMS1010U EMS1016U EMS1010U EMS1016U EMS1016U EMS1000E EMS1000E EMS1000E EMS1000E EMS1000E EMS1000E EMS1006E EMS1000E EMS1006E EMS1006E EMS1010E EMS1010E EMS1010E EMS1010E EMS1010E EMS1010E EMS1016E EMS1010E EMS1016E EMS1016E Elbex Bldg. 1-11, Nishi-Gotanda 8-Chome, Shinagawa-ku Tokyo 141-0031, Japan Tel:(03) 3779 - 5222 Fax:(03) 3779 -5201 10761 Noel Street, Los Alamitos, CA 90720, U.S.A. Tel:(714) 761- 8000/ (800) FOR-CCTV, Fax:(714) 761- 8400 NORTHWEST OFFICE:33739-9th Ave South Federal Way, WA 98003 Tel:(253) 925 -2111 Fax:(253) 925 -2112 300, Corporate Dr., Suite 5, Blauvelt, NY 10913, U.S.A. Tel:(845) 353 -0600 / (800) 343 - 5239 Fax:(845) 353 -0657 ELBEX AMERICA (N.Y.) INC. ELBEX (DEUTSCHLAND) GMBH Arzberger Str. 2, D- 93057 Regensburg, Germany Tel:(0941) 69531- 0 Fax:(0941) 68306 ELBEX (UK) PLC ELBEX House, Phoenix Business Park Avenue Road, Birmingham, B7 4NU, U.K. Tel:(121) 359 - 6611 Fax:(121) 359 - 8080 LONDON OFFICE: The Pavillions, Kiln Lane, Epsom, Surrey KT17 1JG Tel:(0137)274-7776 Fax:(0137)274-7675 ELBEX BENELUX N.V. Katwilgweg 11, 2050 Antwerpen, Belgium Tel:(03)254-0954 Fax:(03)254-0323 De Maas 13, 5684 PL Best, Holland Tel:0499 - 372025 Fax:0499 - 372199 ELBEX NEDERLAND ELBEX FRANCE 17 rue Casimir Perier, 95875 Bezons Cedex, France Tel:01.34 .23.59.00 Fax:01.30.76.16.13 ELBEX VIDEO LTD. (ISRAEL) 8, Kehilat Venezia St. Tel Aviv 69010, Israel Tel:972 - 3 - 6494149 Fax:972-3 - 6494561 ELBEX SCANDINAVIA A/S Damhus Boulevard 98, DK-2610 Roedovre Denmark Tel:(36)730020 Fax:(36)730029 Datavagen 6, S- 436 32 Askim, Sweden Tel:(031) 748 07 95 Fax:(031) 748 07 99 ELBEX SWEDEN Unit A, 1/F. On Fat Industrial Building, 12-18 Kwai Wing Road, Kwai Chung, N.T., Hong Kong Tel:27987608 Fax:27987774 ELBEX VIDEO (H.K.) LTD. ELBEX AUSTRALIA PTY. LTD. SYDNEY: Unit 15, 20 - 30 Stubbs Street, Silverwater, NSW 2128, Australia Tel:(02) 9748 6377 Fax:(02) 9748 6090 MELBOURNE: Unit 2, 15, Shearson Crescent, Mentone, Vic. 3194 , Australia Tel:(03) 9583 8122 Fax:(03) 9583 6447 BRISBANE: Unit 1, 121 Newmarket Street, Windsor, Qld. 4030, Australia Tel:(07) 3857 6411 Fax:(07)3857 6445 ELBEX SINGAPORE PTE. LTD. 153 Kampong Ampat #05 - 03, Junjie Industrial Bldg., Singapore 368326 Tel:285 6233 Fax:382 3978 LTD. ELBEX AMERICA INC. Printed in Japan, February, 2001