Transcript
al ! st e to or bi dd en
il f
ile
,f
fa
nv
Version: Release date:
<2014-2-12>
© 2011 - 2014 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd (Abbreviated as Fanvil hereafter). Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
Specifications are subject to change without notice.
fa
nv
il f
ile
,f
or bi dd en
to
st e
al !
Liability Disclaimer Fanvil may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked as reserved or undefined. Fanvil reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The information here is subject to change without notice. Do not finalize a design with this information. The products described in this document may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Fanvil sales office or your distributor to obtain the latest specification and before placing your product order.
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
2
al !
Table of Contents
Table of Contents ................................................................................................................................... 3
Revision History ........................................................................................................................... 4
2
Introduction .................................................................................................................................. 5 2.1 2.2
Overview ............................................................................................................................... 5 Target Audience ................................................................................................................... 5
........................................................................................................ 6
,f
or bi dd en
to
................................................................................................................. 6 GLOBAL CONFIG MODULE ................................................................................................ 6 LAN CONFIG MODULE ..................................................................................................... 11 TELE CONFIG MODULE ................................................................................................... 11 DSP CONFIG MODULE ..................................................................................................... 17 SIP CONFIG MODULE ...................................................................................................... 20 IAX2 CONFIG MODULE .................................................................................................... 30 MCAST CONFIG MODULE................................................................................................ 31 PPPoE CONFIG MODULE................................................................................................. 32 MMI CONFIG MODULE ..................................................................................................... 32 QOS CONFIG MODULE .................................................................................................... 34 DEBUG CONFIG MODULE ............................................................................................... 35 AAA CONFIG MODULE ..................................................................................................... 35 ACCESS CONFIG MODULE ............................................................................................. 36 DHCP CONFIG MODLUE .................................................................................................. 36 NAT CONFIG MODULE ..................................................................................................... 37 PHONE CONFIG MODULE ............................................................................................... 38 SCREEN KEY CONFIG MODULE ..................................................................................... 44 AUTOUPDATE CONFIG MODULE ................................................................................... 46 VPN CONFIG MODULE ..................................................................................................... 47 DOT1X CONFIG MODULE ................................................................................................ 48 TR069 CONFIG MODULE ................................................................................................. 48
fa
nv
il f
3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22
ile
3
st e
1
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
3
Revision History
al !
1
Author
Date
Description
1.0.0
<2014-02-12>
fa
nv
il f
ile
,f
or bi dd en
to
Revision
st e
Revision history:
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
4
Overview
st e
2.1
Introduction
al !
2
2.2
or bi dd en
to
Fanvil C series products of the company's new products, so we will provide the perfect C series product related documents, and increases the detailed information about the configuration, to help users a comprehensive understanding of Fanvil VoIP products C series product configuration file, if according to the file format, TXT and XML;If according to the document classification, system configuration and equipment configuration file two types. In addition if FILE based framework, the definition OF configuration to < < VOIP CONFIG FILE > > as a start tag, in < < the END OF the FILE > > as the ending tag;If based on the model, the configuration file can have version and digests in two ways We will based on C62 V23 version described in detail the architecture of the configuration file and the configuration items.
Target Audience
fa
nv
il f
ile
,f
This document in Xml Remote telephone need to test the function of internal staff and customers.
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
5
al !
3
or bi dd en
to
st e
System configuration files are usually includes the following modules: 1. GLOBAL CONFIG module 2. LAN CONFIG module 3. DSP CONFIG module 4. PPPoE CONFIG module 5. MMI CONFIG module 6. QOS CONFIG module 7. DEBUG CONFIG module 8. AAA CONFIG module 9. ACCESS CONFIG module 10. DHCP CONFIG module 11. PHONE CONFIG module 12. SCREEN KEY CONFIG module 13. AUTOUPDATE CONFIG module 14. VPN CONFIG module 15. DOT1X CONFIG module 16. TR069 CONFIG module Details of these modules in the configuration file can be downloaded directly by terminal equipment check.
3.1
FILE header keyword and version information contained in the beginning, for example, FILE header is a < < VOIP CONFIG FILE > > % CUS_VERSION % : % CUS_VERSION_NUMBER %.If the file header contains digests, so only on the server configuration file do not match the configuration file and terminal, terminal will upgrade;If the file does not contain digests, so by changing the version number, upgrade
,f
Note: the length of the first line of the file must be 64 characters
GLOBAL CONFIG MODULE
ile
3.2
il f
Global configuration module covers the entire configuration, network interfaces, which are included with the RTP port, SNTP, daylight saving time, the Action URL configuration module, etc Note1: the configuration file parameters length of 20 characters, including ":" Note2: the configuration parameter illustrative introduced 20 characters in length, case insensitive Global Config Module
Description
WAN Mode
Network model is a way of Internet access, DHCP, static network, including the PPPoE, for DHCP mode by default
WAN IP
Network IP address, and support the IPv4 address mode
fa
nv
Name
WAN Subnet Mask
Subnet mask ,support the IPv4 address mode
WAN Gateway
Gateway , support the IPv4 address mode
Default Protocol
The default protocol, support SIP, PSTN, IAX2 protocol, etc.If the value of 2 means using the SIP protocol;If the value of 3 means using PSTN agreement;If
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
6
al !
the value of 4 means using the IAX2 protocol.The default using the SIP protocol.(PSTN protocol used in the gateway only) Primary DNS, gives priority to the DNS server, use it to IPv4 address mode
Secondary DNS
Backup DNS, when the primary DNS server cannot be used properly, automatically using backup DNS server, its to IPv4 address mode
Enable DHCP
DHCP network mode is optional configuration.If the value is 1, the model for DHCP, if the value is 0, the model for the static network, not with the Enable PPPoE value to 1 at the same time.The default is 1
Use Vendor Class ID
Enable manufacturers identification code, the network data interaction can be included in the corresponding vendor information, if is not enabled, the network information data will not contain the manufacturer.Is not enabled by default
Vendor Class ID
Set manufacturer identification code, the default format for Vendor + model form, support manual configuration
DHCP Auto DNS
Through DNS DHCP automatically, if the value is 1, said is enabled, the DNS server addresses to be received by DHCP;If the value is 0, said is not enabled, the DNS server will use the parameters in the static network directly.Enabled by default
DHCP Auto Time
Carry through the DHCP parameters to gain time and SNTP server address.Is not enabled by default
Domain Name
DNS domain name
Host Name
Terminal host name, the default value for VOIP
Enable PPPoE
PPPoE network mode is optional configuration . If the value is 1, the current network mode for PPPoE, if value is 0 , is not currently open PPPoE . Is not enabled by default
RTP Initial Port
RTP voice packets starting port, the first port of RTP call, default value is 10000
RTP Port Quantity
RTP voice packets port number, said on the basis of the initial port , can increase the number of ports, the default value is 200
to
or bi dd en
,f
SNTP Server
Main SNTP server, preferred to use SNTP server address, Terminal can be connected to SNTP server update corresponding time through the network
SNTP
Backup SNTP server, when the main SNTP server can’t be used properly, it will automatically switch to the backup SNTP server, and update the time synchronization
ile
Second Server
st e
Primary DNS
If the value is 1, will be through the SNTP server configured, update the corresponding time; if the value is 0, is not updated by means of SNTP time . The default is enable SNTP service
Time Zone
Select the corresponding time zone of the area .Default to 56,Beijing time
nv
il f
Enable SNTP
Time zone names, and corresponding to the name of the selected time zone, The default is CST_008
Enable DST
If the value is 1, enabling daylight saving time;If the value is 0, is not enabled daylight saving time.The user can be configured according to the local actual situation.Is not enabled by default
fa
Time Zone Name
SNTP Timeout
Though the network connection SNTP server update local time intervals .Default is 60 , said 60 seconds will be a time of synchronization with the SNTP server
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
7
Daylight saving time change length , the default value is 60 minutes
DST Start Mon
Daylight saving time start, in the choice of support January - December. The default is 3,said in March
DST Start Week
Daylight saving time starting weeks , the choice of support 1 – 6 weeks . The default is 5, said the fifth week
DST Start Wday
Daylight saving time start week , support the choice to 0 – 6 , 0 said Sunday, 6 said Saturday . The default is 0, said on Sunday
DST Start Hour
Daylight saving time start hours , support manually enter 0 – 24 hours a day . The default is 2, said 2 PM
DST Start Min
Daylight saving time start minutes , support manually enter 0 – 60 specific detailed minutes , The default is 0.
DST End Mon
Daylight saving time by the month, the choice of support 1 – 12 month . the default is 10, said in October
DST End Week
Daylight saving time by weeks , the choice of support 1 – 6 weeks , The default is 5 , said the fifth week
DST End Wday
Daylight saving time by week, support the choice of 0 – 6, 0 said Sunday, 6 said Saturday. The default is 0 , said on Sunday
DST End Hour
Daylight saving time by the hour, support manually enter 0 – 24 hours , The default is 2 , said 2 PM
DST End Min
Daylight saving time by minutes , support manually enter 0 – 60 specific detailed minutes . The default is 0
Default UI
Set WEB page and LCD display the default language, the default is 1, said after the restore factory setting, the phone’s default language is english
MTU Length
The maximum transmission unit length , the default value is 1500
Push XML IP
Set the terminal to push XML file server address
Enable Call History
If the value is 1 , the terminal has a call history in call records , if the value is 0, the terminal don’t display the call history in call records . The default is 1(enable)
st e
to
or bi dd en
,f
Active Uri IP
Configure the IP address of the remote host , the remote host operated terminal via a URI information
Completed
Terminal completely started , terminal report start the complete event to host via the URL
ile
Boot Url
al !
DST Min Offset
Reg On Url
il f
Terminal registered success, terminal report registration successful event to host via the URL Terminal report cancel the registration event via the URL when cancel the l registration
Reg Failed Url
Terminal registration failed, terminal report the registration failed events to host via the URL
nv
Reg Off Url
Offhook Url
Terminal offhook, terminal report the offhook event to host via the URL
Onhook Uri
Terminal onhook , terminal report the onhook event to host via the URL
Call
Terminal calls incoming , terminal report calls incoming event to host via the URL
Outgoing Url
Call
Terminal have call, terminal report calls event to host via the URL
fa
Incmoing Url
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
8
Terminal connect to talk on the phone, terminal report connect to talk event to host via the URL
Call Stop Url
Terminal end call , terminal report end call event to host via the URL
DND On Url
Terminal enable DND, terminal report enable DND event to host via the URL
DND Off Url Always FWD Url
Terminal disable DND, terminal report disable DND event to host via the URL
FWD
On
Terminal enable unconditional forward, terminal report enable unconditional forward event to host via the URL
Off
Terminal disable unconditional forward, terminal report disable unconditional forward event to host via the URL
st e
Always Url
al !
Call Active Url
Terminal enable busy forward , terminal report enable busy forward event to host via the URL
Busy Url
Off
Terminal disable busy forward , terminal report disable busy forward event to host via the URL
On
Terminal enable no answer forward , terminal report enable no answer forward event to host via the URL
No Ans FWD Off Url
Terminal disable on answer forward, terminal report disable no answer forward event to host via the URL
Transfer Url
Terminal transfer , terminal report transfer event to host via the URL
B Transfer Url
Terminal blind transfer , terminal report blind transfer event to host via the URL
A Transfer Url
Terminal attend transfer , terminal report attend transfer event to host via the URL
Hold Url
Terminal hold, terminal report hold event to host via the URL
Unhold Url
Terminal unhold , terminal report unhold event to host via the URL
Missed call Url
Terminal have missed call, terminal report missed call event to host via the URL
IP Change Url
Terminal IP address changes , terminal report IP address change event to host via the URL
Idle Url
to
Busy
Terminal idle to busy, terminal report turn idle busy event to host via the URL
Busy Url
to
Idle
Terminal busy to idle , terminal report busy turn idle event to host vial the URL
or bi dd en
FWD
ile
No Ans Url
,f
FWD
to
Busy FWD On Url
Example：
fa
nv
il f
WAN Mode :DHCP WAN IP :192.168.1.179 WAN Subnet Mask :255.255.255.0 WAN Gateway :192.168.1.1 Default Protocol :2 Primary DNS :202.96.134.133 Secondary DNS :202.96.128.68 Enable DHCP :1 Use Vendor Class ID:0 Vendor Class ID :Fanvil C62 DHCP Auto DNS :1 DHCP Auto Time :0 Domain Name : Host Name :VOIP Enable PPPoE :0 RTP Initial Port :10000
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
9
fa
nv
il f
ile
,f
or bi dd en
to
st e
al !
RTP Port Quantity :200 SNTP Server :209.81.9.7 Second SNTP Server : Enable SNTP :1 Time Zone :56 Time Zone Name :CST_008 Enable DST :0 SNTP Timeout :60 DST Min Offset :60 DST Start Mon :3 DST Start Week :5 DST Start Wday :0 DST Start Hour :2 DST Start Min :0 DST End Mon :10 DST End Week :5 DST End Wday :0 DST End Hour :2 DST End Min :0 Default UI :2 MTU Length :1500 Push XML IP : Enable Call History:1 Active Uri IP : Boot Completed Url : Reg On Url : Reg Off Url : Reg Failed Url : Offhook Url : Onhook Uri : Incmoing Call Url : Outgoing Call Url : Call Active Url : Call Stop Url : DND On Url : DND Off Url : Always FWD On Url : Always FWD Off Url : Busy FWD On Url : Busy FWD Off Url : No Ans FWD On Url : No Ans FWD Off Url : Transfer Url : B Transfer Url : A Transfer Url : Hold Url : Unhold Url : Mute Url : Unmute Url : Missed call Url : IP Change Url : Idle to Busy Url : Busy to Idle Url :
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
10
LAN CONFIG MODULE
al !
3.3
LAN LAN port module mainly for terminal network configuration LAN CONFIG MODULE Description
LAN IP
Terminal LA N IP，default is 192.168.10.1
LAN SubNetMask
Terminal LAN subnet mask，default is 255.255.0.0
Enable Bridge Mode
If the value is 1, said to enable bridge mode, the unit under the LAN port of device and WAN port will use the same IP network segment;Routing mode, if the value is 0, said the use of telephone equipment under the LAN port will use LAN port IP communication within the designated IP segment.The default is 1, enabled
Enable Port Mirror
Only talk effect in bridge mode, Enable the Port Mirror，will be able
to
st e
Name
Example： LAN IP LAN SubNetMask Enable Bridge Mode Enable Port Mirror
or bi dd en
to capture of the WAN Port through the LAN Port of network information, otherwise, cannot capture.The default is 1, enabled
:192.168.10.1 :255.255.0.0 :1 :1
Note: all LAN module configuration will be effective after the restart!
3.4
TELE CONFIG MODULE
TELE CONFIG MODULE mainly include dial plan and the phone features related to the configuration of the module. TELE CONFIG MODULE
Description
,f
Name
ile
Dial by Pound
il f
BTransfer by Pound
nv
Onhook to BXfer
fa
Onhook to AXfer
Press “#” to send. if the value is 1, after user input number, as long as the input “#” again, can directly receive, notice sent out at this time the number does not include “#”;If the value is 0, the user input number again, even if the input “#” will not to accept to send .The default value is 1, enable Press “#” to do blind transfer. If the value is 1, user can realized blind transfer though “#” end; if the value is 0 , not by “#” to do blind transfer. The default is 1,enable Blind transfer on Onhook, if the value is 1, user can realize blind transfer though on Onhook, if the value is 0, user can’t achieve blind transfer, the default is 0,disable Attend transfer on Onhook，if the value is 1, the user can transfer by hang up to attend, if the value is 0,hang up will not realize transfer to attend, the default value is 0,disable
Memory Key to BXfer
Press DSSKEY to do blind transfer, If the value is 1, the user can blind transfer by DSS key implementation;If the value is 0, don't blind transfer was achieved by hang up.The default is 0, is not
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
11
enabled Transfer on conference Onhook , if the value is1, conference talking,user can transfer by hang up ,if the value is 0, will not realize this function,default is 0,disable
Dial Fixed Length
Dial fixed length to send, if the value is 1, send to number when input number length reaches the preset number, if the value is 0,even reaches preset length not to send, the default is 0,disable
Fixed Length Nums
Set fixed length of number, user can enable default number of fixed length, default is 11,said input number length reaches 11 numbers ,automatic to send
Dial by Timeout
Send after timeout. If the value is 1, dial number when user will not input response than the preset time on dialing screen immediately, if the value is 0, do not use the rules for overtime, the default is 1, enable
Dial Timeout value
Set the timeout time, user can set timeout time value to send, the default is 5, said the input number automatically to dial after 5 seconds
or bi dd en
to
st e
al !
Xfer On Conf Onhook
Dialpeer With Line
Set DialPeer call line . if the value is 0, using SIP line to call , if the value is 0, uing the IAX2 protocol to call, the default is 0
Port Sequence
Set the query port table mode (only applicable for multi-port gateway).If the value is 1, the terminal from high-end voice channel mouth into the low end of the mouth sequential search.If the value is 0, the terminal will be from the voice channel from the low-end to high-end mouth mouth sequential search.The default is 0.
Accept Any Call
,f
Answer any calls , if the value is 1, any calls (includes anonymous calls ,ect)can be inbound is answered , if the value is 0, anonymous call will not be allowed to income , the default is 1, enable Gateway prefix（H323 protocol support ）
Main Digit Prefix
ile
IP Dial Prefix
il f
P1 Enable DND
nv
P1 Mute Ringing
fa
P1 CWaiting Tone
If set the IP dialling prefix, for IP dial, will automatically be before input the number of automatic prefixed with dial Enable don’t disturb , if the value is 0, not enable disturb for all lines, if the value is 1, said to all lines to enable DND, if the value is 2, said on the pecified routes enable DND, the default is 0, all line use DND Mute incoming ringing , if the value is 1, caller display only hint ,ont play ringing , if the value is 0,the telephone rings ,the default is 0, disable Call waiting tone . if the value is 1, the second incoming ringing, there will be call s prompt , if the value is 0, the second incoming,there will be no calls prompt, the default is 1, enabled
P1 Ban Dial Out
Ban dial out, if the value is 1, can’t to call,but answer the phone normally, if the value is 0, disable ban dial out,the default is 0,disable
P1 Ban Empty CID
Do not accept empty calling the call.The default is 0, is not
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
12
enabled. Called id(gateway),the default is 1, enable for incoming display
P1 CallWaiting
Enable call waitig . if the value is 1, has been all the way to speak, more calls can still income; If the value is 0, said has been all the way to speak, other calls will be banned from inbound.The default is 1, enabling inbound (maximum 10 lines and establish talking)
P1 CallTransfer
Enable call transfer, if the value is 1, the terminal can be used to transfer function;If the value is 0, the terminal can not use call transfer.The default is 1, enabled
P1 CallSemiXfer
Enable call semi attend transfer, value is 1, enable; if value is 0, disable, default is 1, disable
P1 CallConference
Enable call conference, if value is 1, can local conference or server conference talking with other terminal , if value is 0, can’t conference opeaation, the default value is 1, enable
P1 AutoAnswer
or bi dd en
to
st e
al !
P1 Enable CLIP
Enable auto answer . if the value is 1, under stardby ,have calls incoming , at the preset time, automatically answer, if the value is 0, have incoming ,only can answer manually, the default is 0, disable
P1 No Answer Time P1 Warm Line Time P1 Port Ext Num
Automatic response time, set automatic answer of the preset time ,the unit is seconds The warm line number dial time setting, the default value is 0, the unit of a second Ues in DEVICE ID mode registered, can configure the number of the phone
P1 Hotline Num
,f
Hotline number, if the value is not empty, press the line key, handsfree headset, or offhook is will directly dial number in reaches the preset time;If is empty, even at the preset time, also won't perform automatic call.The default is empty Record number.
P1 Use SRV Record
Whether to enable recording
P1 Auto PickupNext
End the current call, automatic answer the new call.The default is 0, is not enabled
P1 Busy No Line
If the value is 0, play dial tone forever;If the value is 1, have played a dial tone on the SIP registration, otherwise don't play.The default is 0, is not enabled
il f
ile
P1 SRV Record Num
nv
P1 Auto Onhook
Handsfree Onhook automatically,if the value is 1, after the call end,will be direct return to standby mode when after the preset time, if the value is 0, after the call end, need to manually back to standby, the default is 1, enable Automatically Onhook time, set the end of the call ,direct return to the standby time . the default is 3 seconds
P1 DND Code
DND return code, the default is 4800, said the terminal to enable DND, have incoming,will give the server return 480 ,synchronous for the server, in addition can also choose to return code 480, 603
fa
P1 Auto Onhook Time
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
13
Busy return code, the default value is 486,if the terminal in busy mode,incoming call ,will give the server return 486,synchronous for the server, or can choose 480,603 return code
P1 Reject Code
Refused to return code, the default value is 603, if incoming was rejected, will the server return cod 603,synchronous for the server,or choose to return code 480,486
P1 Enable Intercom
Intercom response, if the value is 1,it was intercom in standby,automatically answer, if the value is 0, the intercom, ringing,can’t automatically answer, the default is 1, enable
P1 Intercom Mute
Intercom mute, if the value is 1, intercom call will enable the mute mode, if the valus is 0, is not enable mute mode, default is 0,disable
P1 Intercom Tone
Intercom prompt tone.If the value is 1, under standby Intercom inbound, automatic answer will play a tone;If the value is 0, under standby Intercom incoming, automatic answer directly.Note only Intercom automatic answer, will play tone prompt.The default is 0, is not enabled
P1 Intercom Barge
or bi dd en
to
st e
al !
P1 Busy Code
Mult Intercom calls, Intercom inbound answer function.If the value is 1, the terminal in the call, have Intercom inbound and automatically answer;If the value is 0, Intercom cannot inbound.Note that if the calls Intercom are contained in the communication, so will not be able to build new calls by Intercom.The default is 0, is not enabled Automatic redial functions.If the value is 1, the call number in a busy state, and the pop-up dialog box in the preset time after n times, dial (default), also can undertake manual dialing, click on the button in the dialog or cancel the dial;If the value is 0, will not enable automatic redial functions.The default value is 0, is not enabled
,f
P1 Use Auto Redial
Set auto redial time interval , unit for seconds, default is 10
P1 AutoRedial Times
Set auto redial the number of times, if the client has been busy, terminal will be completed in the redial corresponding preset number ,end redial ,the default is 10
P1 Call Complete
Call Complete function.If the value is 1, the end of the unit from busy to idle state, the end the pop-up dialog, manually dial back or canceled;If the value is 0, will Call Complete function is not enabled.The default value is 0, is not enabled
il f
ile
P1 AutoRedial Delay
fa
nv
P1 Hide DTMF Type
P1 Talk DTMF Tone
Hide the DTMF function.If the value is 0, the DTMF call input, all will be on the LCD display;If the value is 1, input of DTMF call, will be hidden in the LCD, all with * display;If the value is 2, call the DTMF input will display properly first, and then displayed in a *;If the value is 3, call the input of DTMF is always the last one, according to the normal other are displayed in a *.The default is 0, all DTMF normal display DTMF tone in talking mode,if the value is 1, play local DTMF in the
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
14
al !
talking mode, if the value is 0, DTMF tone in talking mode can’t play ,default is 1,enable Paly DTMF Tone in dialing, if the value is 1, DTMF on dial state can play tone, if the value is 0, DTMF tone on dialing mode, can’t play,the default is 1,enable
P1 Psw Dial Mode
Password dial-up function, .If enabled, you can according to the preset number prefix number to determine whether encryption, judging by the default password length to encrypt the number of digits;If the value is 0, dial does not enable encryption function.The default is 0, is not enabled
P1 Psw Dial Length
Password length dial.The default to hide the password length.The default is 0
P1 Psw Dial Prefix
Enable password dial-up number prefix.If set number prefix, will be used only for matching prefix number password dial-up.If there is no set number prefix, for all Numbers to enable password dial-up function.
P1 Enable MultiLine
P1 Allow IP Call
Default extern line ,default is 0, disable
Default Ans mode
Automatic answer mode, if the value is 0, voice response, if the value is 1, said the voice and video connect , default is 0,voice answer
Default Dial mode
Automatically dial out mode, if the value is 0,voice out, if the value is 1, voice and video dial , default is 0, voice dial out
,f
Dial by Pound
To enable more line function.If the value is 1, the terminal can support 10 calls, incoming calls,If the value is 0, calls incoming terminal only support 2 road.The default is 1, enabled Enable IP direct function.If the value is 1, you can use the IP call;If the value is 0, don't call via IP.The default is 1, enabled
Default Ext line
Example：
or bi dd en
to
st e
P1 Dial DTMF Tone
:1
BTransfer by Pound :1
:0
Onhook to AXfer
:0
ile
Onhook to BXfer
Memory Key to BXfer:0
il f
Xfer On Conf Onhook:0
Dial Fixed Length :0
Fixed Length Nums :11 Dial by Timeout
:1
nv
Dial Timeout value :5 Dialpeer With Line :0
:0
Accept Any Call
:1
fa
Port Sequence
Main Digit Prefix : IP Dial Prefix
:.
--Port Config--
:
P1 Enable DND
:0
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
15
:1
P1 Ban Dial Out
:0
P1 Ban Empty CID
:0
P1 Enable CLIP
:1
P1 CallWaiting
:1
P1 CallTransfer
:1
P1 CallSemiXfer
:1
al !
:0
P1 CWaiting Tone
st e
P1 Mute Ringing
P1 CallConference :1 P1 AutoAnswer
:0
to
P1 No Answer Time :20 P1 Warm Line Time :0 P1 Port Ext Num
:
P1 Hotline Num
:
P1 Use SRV Record :0 P1 Auto PickupNext :0 P1 Busy No Line
:0
P1 Auto Onhook
:1
P1 Auto Onhook Time:3 P1 DND Code
:1
P1 Busy Code
:2
P1 Reject Code
:3
P1 Enable Intercom :1 P1 Intercom Mute
:0
P1 Intercom Tone
:1
P1 Intercom Barge :1
,f
P1 Use Auto Redial :0
or bi dd en
P1 SRV Record Num :
P1 AutoRedial Delay:10 P1 AutoRedial Times:10 :0
ile
P1 Call Complete
P1 Hide DTMF Type :0 P1 Talk DTMF Tone :1 P1 Dial DTMF Tone :1
:0
il f
P1 Psw Dial Mode
P1 Psw Dial Length :0 P1 Psw Dial Prefix :
nv
P1 Enable MultiLine:1 P1 Allow IP Call
:1
Default Ext line
:0
Default Ans mode
:0
fa
Default Dial mode :0
Note: Dial plan in hands-free,offhook, headset and other non appropriations state of use;”#” to send, fixed length, timeout number, dial plan table can be used at the same time, as long as the user dial over satisfied with any kind of judgment, will be the end of the number, the number is sent out.
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
16
DSP CONFIG MODULE
al !
3.5
DSP CONFIG MODULE MODULE mainly includes voice parameters related parameters Settings DSP CONFIG MODULE Decription
Signal Standard
Set the standard signal. set the value of 1 to 8,respectively
st e
Name
corresponding to the signal of 18 region ,dialing screen can be
set according to the area of the dialing tone, busy tone,etc .the default is 1, China
Enable voice message tone. The value is 0,disable voicemail
Enable MWI Tone
to
message tone has won’t play voice to voice mail; the value is 1, enable voicemail message tone with voice message to prompt,the default I 1, enable voice message prompt
Set the mix response time of Onhook. Setting response time of
or bi dd en
Onhook Time
Onhook, in the setting of time quickly pres onhook, it won’t response,example,int the reaction time quickly press the onhook don’t hang up the current call in talking screen,the default is 200,unit is milliseconds Set
G729 Payload Len
G729
Payload
length.
0,1,2,3,4,5
respectively
10
millseconds,20 millseconds,30 millseconds, 40 millseconds , 50 millseconds,60
millseconds.
The
default
is
1,
use
20
millseconds,use G729 voice code to build communication,to carray the number by bytes to 20. Set the G723 Bit Rate
G723 Bit Rate
ile
,f
0， 5.3Kb/s, use G723 voice code connect a call ，high-rate speech is 5.3Kb/s 1， 6.3Kb/s, use G723 voice code connect a call，high-rate speech is 6.3kb/s The default is 1，use 6.3Kb/s
nv
il f
G722 Timestamps
fa
VAD
Set the G.722 timestamp 0， 160/20ms ， Use G722 voice code on the call ， to send voice packets every 20ms ， timestamp field between adjacent two voice packet length will increase to 160 1， 320/20ms ， Use G722 voice code on the call ， to send voice packets every 20ms，temstamp field between adjacent two voice packet length will increase to 320 The default is 0 Enable noise detection If the value is 0，disable VAD Value is 1，enable VAD，HD handset for noise detection, the unit G711A/U voice coding set up after the call ,for a long time in a quiet environment,played a slight voice, prompt the current call not over yet
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
17
The default is 0, don’t enable the noise detection
al !
Set the default ringtone
Ring Type
1-9 is show ringtone Type1-Type9 101-103 is show ringtone user1-suer3
st e
The default value is 1, use the default ringtone for Type1, telephone ringing tone for Type1 Dtmf Payload Type
Set the DTMF payload length
DTMF payload length range is 96-127,the default value is 101
RTP Probe. Some server needs to send RTP, just can have response,
RTP Probe
the default value is 1, enable
to
will make some equipment lost voice. So need to send RTP probe, Enable the HD voice, when the value is 0,is not enable HD voice,
HD Voice
or bi dd en
the phone does not support high-definition handle; the value is 1, enable the HD audio, phone support HD handle Handle send physical gain, the greater the value, the greater the
TX AGC
sound
Handle receiving physical gain, the greater the value,
RX AGC
the
greater the sound
Sidetone remove. Can eliminate sidetoe in the process of calls,
Sidetone GAIN
to avoid hearing yourself voice.
P1 General Spk Vol
Set the handle call volume. Speak to handle the volume rang of 19,handle telephone calls the volume change according to the set value, the default value is 5
P1 General Mic Vol
Set up radio call volume
,f
Phone cals received when the volume can be change according to set value, the default is 5 Set the headset volume
P1 Headset Vol
ile
Headset volume value range is 1-9,calls of headset volume can be change according to the set values . the default is 5
nv
il f
P1 Ring in Headset
The value is 1, enable automatically headset ringing , telephone plug in headset, have ringing
calls, play ringtone through
headset. When the value is 0,disable automatic headset ringing, have ringing calls ,paly ringtone through the speaker. The default value is 0, disable automatically ringing in headset
P1 Auto Headset
fa
Enable automatic headset ringing.
Enable automatic headphones.Value
is
automatically
we
headphones,
when
0,
the is not enabled
have
to
call
phone
automatically by the timeout answer, answer, Line key answer is to
establish
a
hands-free
or
handle
calls
The value is 1, enable automatic headphones, when we have to call
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
18
answer, answer, Line
timeout
is
set
up
key answer automatically by the headphones
on
the
The default is 1, enable automatic headphones P1 Headset Ring Vol
phone
al !
phone
Set the ring tone headphone volume. Headphones ringing volume according to set value. The default is 5
st e
value range is 1 to 9, headphones ringing volume can be change Set handfsfree call volume. Handsfree calls volume value range is
P1 HandFree Vol
1-9, the volume of the handsfree calls can be change according to set value. The default value is 5.
to
Set handsfree ringtone volume. Handsfree ringing volume in the
P1 RingTone Vol
range of 1-9, handsfree ringing volume can be change according to set value. The default value is 5 Set the first voice code algorithm
or bi dd en
P1 Voice Codec1
PCMA/8000，is G.711A
PCMU/8000，is G.711U G722/8000，is G.722
G723/8000，is G.724
G729/8000，is G.729
G726-32/8000，is G.726
The default is PCMA/8000
Set the second voice code algorithm
P1 Voice Codec2
Same as above，the default is PCMU/8000 Set the third
P1 Voice Codec3
voice code algorithm
Same as above，the default is G722/8000 Set the forth voice code algorithm
,f
P1 Voice Codec4
Same as above，the default is G729/8000
P1 Voice Codec5
Set the fifth voice code algorithm
ile
The default is empty Set the sixth voice code algorithm
P1 Voice Codec6
The default is empty
il f
Codec1 Format
Codec2 Format Codec3 Format
nv
Codec4 Format Codec5 Format Codec6 Format
fa
Codec7 Format Example： Signal Standard
:1
Enable MWI Tone
:1
Onhook Time
:200
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
19
:1
G723 Bit Rate
:1
G722 Timestamps
:0
VAD
:0
Ring Type
:1
al !
G729 Payload Len
:0
HD Voice
:1
TX AGC
:0
RX AGC
:0
Sidetone GAIN
:1
--Port Config--
:
to
RTP Probe
st e
Dtmf Payload Type :101
P1 General Spk Vol :1 P1 General Mic Vol :3 :3
P1 Ring in Headset :0 P1 Auto Headset
:1
P1 Headset Ring Vol:7
or bi dd en
P1 Headset Vol
:2
P1 RingTone Vol
:8
P1 Voice Codec1
:PCMA/8000
P1 Voice Codec2
:PCMU/8000
P1 Voice Codec3
:G722/8000
P1 Voice Codec4
:G729/8000
P1 Voice Codec5
:
P1 Voice Codec6
:
--Codec Config--
:
Codec1 Format
:PCMA/8000;payload=8;
Codec2 Format
:PCMU/8000;payload=0;
Codec3 Format
:G722/8000;payload=9;
Codec4 Format
:G723/8000;payload=4;bitrate=6.3;
ile
,f
P1 HandFree Vol
:G729/8000;payload=18;annexb=no;
Codec6 Format
:G726-32/8000;payload=2;
Codec7 Format
:telephone-event/8000;payload=101;
il f
Codec5 Format
SIP CONFIG MODULE
nv
3.6
SIP CONFIG MODULE MODULE mainly includes the SIP all the parameter configuration. SIP CONFIG MODULE Description
SIP Port
Local SIP signaling port. The range is 1-65535. The default is 5060
STUN Server
Set STUN server address.
STUN Port
STUN server port. The range is 1-65535. The default value is 3478
STUN Refresh Time
STUN the refresh interval.Words to set every time send a binding
fa
Name
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
20
request packet refresh;The default value is 50, the unit is in seconds SIP waiting STUN response time.After enable of the SIP STUN, STUN setting time response, SIP registration and STUN is carried in response to the call of the network port, or use the network port. The default value is 800 milliseconds
Extern NAT Addrs
External NAT address, if set, line set up different useStun = 2 said using the address, contact address in this address
Reg Fail Interval
Registration failed interval time .If SIP account registration failed, chance every registered retransmission time half again, until the registration;The default value is 32, the unit is in seconds
SIP Pswd Encryption
whether encrypted SIP password.If the value is 1, is to be encrypted.Configuration file can only see the encrypted text, if is 0, is not encrypted, configuration files to see clear;The default value is 0
Strict BranchPrefix
Strict matching Branch field.If the value is 1, enable the configuration item , the SIP phone received messages via field Branch of the value of the words begin with z9hG4bk, reply the phone 4 xx do not response;If the value is 0, disable the configuration items, does not match the Branch field in the SIP message, can receive;The default value is 0
or bi dd en
Video Mute Attr
to
st e
al !
SIP Wait Stun Time
Video incoming voice answered.The video media atrribute keep in sendrecv, but part of the server needs to inactive, judged by the variable.If the value is 1, the unit hold while DSP package with inactive, if the value is 0, hold with sendrecv;The default value is 0 enable the group backup.If the value is 1, enable the configuration item, at this point the unit registered within the same group of the same number of different SIP server, not registered successfully at the same time, namely the SIP1 registered success, SIP2 registered failure, disconnect SIP1, SIP2 registration;If the value is 0, the configuration item is closed, it can register at the same time;The default value is 0
,f
Enable Group Backup
Strictly abide by the RFC4475.If the value is 1, enable the configuration items, at this point the unit receives the from/to field of SIP message with a blank space in the displayname, "", or both, can't set up calls;If the value is 0, the configuration items closed, answering calls properly;The default value is 1
il f
ile
Enable RFC4475
Set the phone number.Used to fill in the registration number
SIP1 Display Name
Set the display name.In standby or call to name displayed on the LCD, than local same number in the phone book and network phone book shows the name of the low priority
nv
SIP1 Phone Number
SIP server name.shows the name of the configuration SIP server
SIP1 Register Addr
Set SIP server address
fa
SIP1 Sip Name
SIP1 Register Port
Register server port. the range is 1-65535；the default is 5060
SIP1 Register Use
Set register user name. for the IP server authentication
SIP1 Register Pswd
Set the register password. For the SIP server authentication
SIP1 Register TTL
Server registration deadline.The range is 0 to 65535 seconds;SIP
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
21
al !
registration expires, the words chance in setting up half the time to the server to send the registration request, to maintain registration status;The default value is 3600, the unit is in seconds Enable register . the value is 0, means enable registration. 0 means disable registration.the default value is 0
SIP1 Proxy Addr
Set up the proxy server IP address
SIP1 Proxy Port
Set up the proxy server port. The range is 1-65535; the default value is 5060
SIP1 Proxy User
Set up the proxy server account.
SIP1 Proxy Pswd
Set up the proxy server password.
SIP1 BakProxy Addr
Set up the backup proxy server IP address.If the primary server address is not available, the opportunity to enable backup proxy server address.
SIP1 BakProxy Port
Set up the backup proxy server port. The range is 1-65535. The default value is 5060
SIP1 SigCrypto Key SIP1 Media Crypto
to
or bi dd en
SIP1 Signal Crypto
st e
SIP1 Enable Reg
Signaling encryption.If the value is 1, enable the configuration items, sip communication encryption, call cannot be caught by sip phone bag;If the value is 0,diablbe the configuration items, communication will not be encrypted;The default value is 0 Set the signal encryption key.
Set media encryption.If the value is 1,enable the configuration items, telephone voice will be encrypted, session call normal on both sides, and through caught cannot hear phone content but noise, if the value is 0, disable the configuration item, through communications caught can hear;The default value is 0
SIP1 MedCrypto Key
Encrypted media encryption.0 s and 1 s on behalf of the use of two different definitions of encryption and authentication algorithms, if the value is 1, using the AES_CM_128_HMAC_SHA1_32 suite, if the value is 0, use AES_CM_128_HMAC_SHA1_80 suite;The default value is 0
ile
,f
SIP1 SRTP Auth-Tag
Set the media encryption key.
The local domain.Set up the SIP domain name, or words to use for SIP server address registered domain name
SIP1 FWD Type
Set forward type.If the value is 0, disable the configuration items;1 is unconditional, before the call is automatically transfer;For 2 is busy before, the unit is in busy reply codes for 486 calls from time to tome, will be moved;Before 3 is no answer, no answer time went unanswered, call will be transferred.The default value is 0
nv
il f
SIP1 Local Domain
fa
SIP1 FWD Number
Configuration forward number.Set to receive transfer party's phone number, after enable forward electricity will be transferred to register the number later on when have ringing calls
SIP1 FWD Timer
Set the no answer forward timer. The range is 0-120 seconds. The default value is 60
SIP1 Ring Type
The ring type.If the value is 0, this configuration for the default ring type, usually the unit will be enabled by default ring 1, if the value is 1-
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
22
al !
9, the corresponding is the default ringtone 1-9, if the value is 101-103, corresponding to the 1-3 is a custom ringtone music;As the default value is 0
Set up a hotline number.If this number is configured, the user to Offhook more than hotline after the delay time is automatically dial the hotline number
SIP1 Enable Hotline
Hotline number.If the value is 1, enable the configuration item, the phone can pick offhook, press the speaker/headset/line, automatically when hotline delay time to exhale hotline number;If the value is 0, the configuration item is closed.The default value is 0
SIP1 WarmLine Time
Set up a hotline delay time.The range is 0 to 9 seconds, telephone hotline number will exhale to time limit;The default value is 0
SIP1 Pickup Num
Set the pickup number.Set the number by function keys to make when they meet in front of the breath number plus the number
SIP1 Join Num
To join the meeting number.Set the number by function keys when they join the meeting in front of the breath number plus the number.
SIP1 NAT UDPUpdate
SIP1 UDPUpdate TTL
Automatically detect the server.If the value is 1, this configuration item type for SIP Option, phone to every set of server detection time Option SIP messages to the server, the server back to the 200 ok to maintain server detection;If the value is 2, this configuration item type for the UDP, words to every configuration server detection time sends UDP messages to the server to maintain the test server.If the value is 0, the configuration item is closed, the unit will not send message to detect;The default value is 1 Setting up a server detect interval.The default value is 60, the unit is in seconds The server type.Choosing the way of signaling encryption or special server types, corresponding COMMON server value is 0, the value 1 corresponding NET2PHONE, a value of 6 corresponding BOTE, value of 14 corresponding NORTEL, a value of 17 corresponding MITEL, corresponding MS_RP value is 22, 23 corresponding value is the CONFIG, value of 24 corresponding FUGITSU, value of 26 corresponding SOFTX3000, value of 28 corresponding BroadSoft, value of 29 corresponding Karel UCAP, a value of 30 corresponding Cellcom, value of 31 corresponding to 3 cx.The default value is 0
il f
ile
,f
SIP1 Server Type
or bi dd en
to
st e
SIP1 Hotline Num
The user agent.Through which users set user agent field, the server through the field judge who's phone
SIP1 PRACK
PRACK.Refers to whether get phone to support SIP PRACK function: (mainly) may be used, if the value is 1, enable the configuration item, if phone have the polyphonic ringtone, in the process of call will send PRACK package;If the value is 0, disalbe the configuration item.The default value is 0
fa
nv
SIP1 User Agent
SIP1 Keep AUTH
When registering with certification.If the value is 1, this configuration is enabled, phone support to register directly with certification to send, this device doesn't have to every time and certification requirements,
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
23
al !
to respond to the server, the server receives with certification of registration request can directly back to the registration confirmation message;If the value is 0, the configuration items closed, registration requires authentication.The default value is 0 The session time.If the value is 1,enable the configuration item, phone when calling regularly send messages, no reply, terminate the call.The default value is 0
SIP1 S.Timer Expire
Session timeout. The default is 0,the unit is in seconds.
SIP1 Enable GRUU
enable GRUU.If the value is 1, enable the configuration items, phone support GRUU;If 0 does not support this feature.The default value is 0
SIP1 DTMF Mode
DTMF type.Deployment of DTMF delivery mode, 0 is the In - band, 1 is RFC2833, 2 is SIP_INFO, 3 to automatically.The default value is 3
SIP1 DTMF Info Mode
DTMF SIP Info type.Choose type of DTMF telephone SIP_INFO, as if the value is 0, when the phone press * / # unit actual value sent for 10/11;If the value is 1, when press the * / #, phone send actual value is * / #.The default value is 0
or bi dd en
to
st e
SIP1 Session Timer
SIP1 NAT Type
NAT type.Whether to enable the SIP line STUN, if the value is 1, enable the configuration, SIP1 enable STUN, 0 to disable.The default is 0
SIP1 Enable Rport
enable Rport.Configuration support RFC3581, enable the configuratio, while value is 1 to 0 when closed.Rport mechanism is used in the network, it is necessary to support SIP server, used to maintain the network devices and network equipment outside NAT connection;The default value is 0
SIP1 Subscribe
,f
enable the MWI subscription.If the value is 1, enable subscription, the unit will subscription information after registering successfully, you can subscribe to other people's status or voice mail, etc., if the value is 0, close the subscription.The default value is 0
SIP1 Sub Expire
ile
Subscribe to the packet expire timeout.Opportunities in the retransmission timeout half way to send subscription package to keep the subscription.The default value is 3600, the unit is in seconds
il f
SIP1 Single Codec
nv
SIP1 CLIR
fa
SIP1 Strict Proxy
Only respond to a voice single codec.When the value is 1,enable the configuration item, called reply of SIP message with phone do a voice coding;When the value is 0, disable the configuration item, reply the sip message with all the voice coding.The default value is 0 An anonymous call specification version.Enabled opportunities in the form of anonymous call each other, each other can't call history view or go back to dial the number.Support RFC3323 and RFC3325, a value of 0 is disabled, is RFC3323 to 1, 2 is RFC3325.The default value is 0 Configuration is compatible with the special server.When the value is 1, enable the configuration item, compatible with the special server, telephone return messages when using the source address of the other party, no longer use via in the address field.When the value is 0, disable the configuration items.The default value is 0
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
24
Value is 0, the two sides through the SIP server communications (phone to send A message to A server, the server to catch to phone B), the value is 1, the two sides to communicate directly (the phone directly to send A message to the unit B).The default value is 0
SIP1 History Info
Enable line for SIP call history information, the default value is 0 (configuration items unused)
SIP1 DNS SRV
Enable the DNS SRV.Support the DNS lookups and _sip. Udp mode, 1 is enabled, 0 for the disabled;The default value is 0.
SIP1 XFER Expire
Transfer timeout.After phone finish attending to hang up, can according to the time set by the hair end call bye.The default value is 0
SIP1 Ban Anonymous
An anonymous call is prohibited.Value is 1, when open this configuration, cannot receive anonymous call;When the value is 0, is not enabled, to receive anonymous calls.The default value is 0
SIP1 Dial Off Line
Allow not registered call.enable this configuration, to 1, with good SIP registration information but not when you start the registration, the unit can exhale through the line operation, but cannot receive incoming;To 0, is not enabled.The default value is 0
SIP1 Quota Name
or bi dd en
to
st e
al !
SIP1 Direct Contact
Configure display name in quotes.If the value is 1, the unit issued a signal when the display name with quotes quotes;If the value is 0, is not enabled.The default value is 0
SIP1 Presence Mode
SIP1 RFC Ver
Enable SIP Presence mode.Support the Presence of two kinds of standard, the value is 0, as the standard, the value is 1, special custom (to support WUCHUAN 806 phone configuration items)
,f
Using configuration protocol specification version.When the unit needs and CISCO5300 use SIP1.0 gateway communication, need to be configured into RFC2543, won't be able to communicate properly.If the value is 1, use the RFC3261;If the value is 0, use RFC2543.The default value is 1
SIP1 Signal Port
Signal port configuration.the default value is 5060
SIP1 Transport
ile
Transport protocol.SIP communications used in the transport protocol, 0 for UDP, 1 for TCP, 3 for TLS.The default is 0
il f
SIP1 Use SRV Mixer
Set conference type.If the value is 1, using the server tripartite meeting;If the value is 0, using local tripartite meeting.The default value is 0, the use of local tripartite meeting Setting up a server tripartite conference number.
SIP1 Long Contact
Configure Contact fields carry more parameters.The default is 0, is not enabled
nv
SIP1 SRV Mixer Uri
fa
SIP1 Auto TCP
Automatically using TCP protocol.If the value is 1, the configuration when the message body of more than 1300 bytes automatically using TCP protocol transmission;If the value is 0, is not enabled.The default is 0, is not enabled.
SIP1 Uri Escaped
Open special character encoding functions.If the value is 1, can put the number in the '#' into "% 23";If the value is 0, is not enabled.The default value is 1, and enabled.Note: if enabled, please close # # at
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
25
the end of the rules. Click on the dial.The default is 0, is not enabled.(reference: if the value is 1, refer to received a call, need software support.)
SIP1 MWI Num
Voice mail number.Can listen to the corresponding number in the message information.
SIP1 CallPark Num
Calls to callpark number.Will call in to the configuration of number, record the speech of the number, and then use other terminal call record number, can call back.
SIP1 MSRPHelp Num
Special custom MS_RP_BU server.After a successful call to set the number.
SIP1 User Is Phone
User = phone functions.If the value is 1, when a call will bring the user = phone fields, mainly in order to support the special server;If the value is 0, is not enabled.The default is 1, enabled.
SIP1 Auto Answer
Automatic answer.If the value is 1, and when there is a telephone call in, and no response after specified time, the terminal automatically answer;If the value is 0, is not enabled.The default is 0, is not enabled.
SIP1 MissedCallLog
SIP1 SvcCode Mode
st e
to
Automatic answer time configuration.The default is 60, the unit is in seconds Call log function.If the value is 1, end the call records of corresponding SIP can have normal line not call records;If the value is 0, the record will not have a corresponding SIP in line not call records.The default is 1, enabled Enable the service code.If the value is 1, the terminal can send the corresponding information notification server update business functions;If the value is 0, is not enabled.The default is 0, is not enabled Configuration DND enable code, when press the DND button, terminal sends set DND unlocking code notification server functions.
,f
SIP1 DNDOn SvcCode
or bi dd en
SIP1 NoAnswerTime
al !
SIP1 Click to Talk
Configuration DND disable code, when press the DND button, the terminal sends set closed DND function code notification server.
SIP1 CFUOn SvcCode
Configuration no conditional forward enable code, when enable unconditional forward , the terminal will send set of unconditional forward before open yards notification server open unconditional transfer function.
il f
ile
SIP1 DNDOff SvcCode
nv
SIP1 CFUOff SvcCode
fa
SIP1 CFBOn SvcCode
Configuration unconditional forward disable code, when close the unconditional forward, terminal will send set of unconditional forwardf code inform server is shut down before the unconditional before transfer function. Configuration busy forward enable code, when open busy forward, the terminal will send set of busy forward notification server open busy before the transfer function.
SIP1 CFBOff SvcCode
Configuration busy forward disable code, when close the busy forward, the terminal will send set of busy turn off code inform server is shut down before the busy before the transfer function.
SIP1 CFNOn SvcCode
Configuration no answer forward enable code, when open no answer
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
26
al !
forward, the terminal will send set no answer forward notification server open no answer before the transfer function. Configuration no answer forward disable code, when close no answer forward, terminal sends set no answer forward code notification server shut down no answer before the transfer function.
SIP1 ANCOn SvcCode
Configuration ban anonymous call enable code, when open the ban anonymous call, terminal will send set of ban anonymous call open yards notification server open anonymous call function.
SIP1 ANCOff SvcCode
Configuration ban anonymous call disable code, when closed to anonymous call terminal will send set of ban anonymous call close code notification server anonymous call function.
SIP1 VoiceCodecMap
Set up voice codec for line.Support to specify each SIP use different voice codec circuit to call.
SIP1 BLFList Uri
Configuration BLFList number, need to open a STUN, notify the subscription BLF number can lookup this number
to
or bi dd en
SIP1 BLF Server
st e
SIP1 CFNOff SvcCode
Configuration BLF to subscribe to the address of the server.If the registration server does not support subscription package, enter BLF server address, separate registered server and subscribe to the server, so also can realize BLF subscription function
SIP1 Respond 182
Compatible with 182 back to the ringing.If the value is 1, when the call hold back 182;If the value is 0, 180 on hold when reply.The default is 0, is not enabled
SIP1 Enable BLFList
Configuration ring caller id priority.Users can configure the display of the priority, for the FROM 1, 2 PAI - the FROM, 3 RPID - FROM, 4 for PAI - RPID - the FROM, 5 for RPID - PAI - the FROM.The default is 1, according to the from the number
ile
,f
SIP1 Caller Id Type
Enable BLLIST function.If the value is 1, to monitor the state of multiple accounts, need to open a STUN, not configured DSS key will be automatically monitored account information, and DSS will change according to the account of the state;If the value is 0, is not enabled.The default is 0, is not enabled
SNTP time synchronization.If 1 is used, the Date field in the 200 ok update SNTP time;If 0, is not enabled.The default is 0, disable
SIP1 Use VPN
Enable the VPN functionality.If the value is 1, will use the VPN IP by registered;If the value is 0, is not enabled.The default is 1, enablet
il f
SIP1 Syn Clock Time
nv
SIP1 Enable DND
fa
SIP1 Update Reg Exp
SIP1 Inactive Hold
Don't disturb.If the value is 1, the corresponding SIP lines cannot be inbound;If the value is 0, the corresponding SIP lines allow inbound phone.The default is 0, disable Special server for compatibility.The default is 1, enable.(reference: if the value is 1, the expires in the register values will carry the expires in 200 OK, special server supports used for compatibility.) Special server for compatibility.The default is 0, disable.(reference: if the value is 1, communication press keep, caught in the SDP invite show inactive; if the value is 0, is not enabled, caught sendonly.)
Example：
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
27
:5060
STUN Server
:
STUN Port
:3478
al !
SIP Port
STUN Refresh Time :50 SIP Wait Stun Time :800 :
st e
Extern NAT Addrs
Reg Fail Interval :32 SIP Pswd Encryption:0 Strict BranchPrefix:0 Video Mute Attr
:0
Enable RFC4475
to
Enable Group Backup:0 :1
--SIP Line List-- : SIP1 Phone Number : SIP1 Sip Name
:
SIP1 Register Addr : SIP1 Register Port :5060 SIP1 Register User : SIP1 Register Pswd : SIP1 Register TTL :3600 SIP1 Enable Reg
:0
SIP1 Proxy Addr
:
SIP1 Proxy Port
:5060
SIP1 Proxy User
:
SIP1 Proxy Pswd
:
SIP1 BakProxy Addr :
,f
SIP1 BakProxy Port :5060
or bi dd en
SIP1 Display Name :
SIP1 Signal Crypto :0 SIP1 SigCrypto Key :
ile
SIP1 Media Crypto :0 SIP1 MedCrypto Key :
SIP1 SRTP Auth-Tag :0 SIP1 Local Domain :
:0
SIP1 FWD Number
:
SIP1 FWD Timer
:60
il f
SIP1 FWD Type
:0
SIP1 Hotline Num
:
nv
SIP1 Ring Type
SIP1 Enable Hotline:0 SIP1 WarmLine Time :0 :
SIP1 Join Num
:
fa
SIP1 Pickup Num
SIP1 NAT UDPUpdate :1 SIP1 UDPUpdate TTL :60
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
28
:0
SIP1 User Agent
:
SIP1 PRACK
:0
SIP1 Keep AUTH
:0
al !
SIP1 Server Type
SIP1 Session Timer :0 SIP1 Enable GRUU
:0
SIP1 DTMF Mode
:3
st e
SIP1 S.Timer Expire:0
SIP1 DTMF Info Mode:0 SIP1 NAT Type
:0
SIP1 Subscribe
:0
SIP1 Sub Expire
:3600
to
SIP1 Enable Rport :0
SIP1 Single Codec :0 :0
SIP1 Strict Proxy :0 SIP1 Direct Contact:0 SIP1 History Info :0 SIP1 DNS SRV
:0
SIP1 XFER Expire
:0
SIP1 Ban Anonymous :0 SIP1 Dial Off Line :0 SIP1 Quota Name
:0
SIP1 Presence Mode :0 SIP1 RFC Ver
:1
SIP1 Signal Port
:0
SIP1 Transport
:0
,f
SIP1 Use SRV Mixer :0
or bi dd en
SIP1 CLIR
SIP1 SRV Mixer Uri :
SIP1 Long Contact :0
:0
ile
SIP1 Auto TCP SIP1 Uri Escaped
:1
SIP1 Click to Talk :0 SIP1 MWI Num
:
il f
SIP1 CallPark Num : SIP1 MSRPHelp Num :
SIP1 User Is Phone :1
nv
SIP1 Auto Answer
:0
SIP1 NoAnswerTime :60 SIP1 MissedCallLog :1 SIP1 SvcCode Mode :0
fa
SIP1 DNDOn SvcCode : SIP1 DNDOff SvcCode: SIP1 CFUOn SvcCode : SIP1 CFUOff SvcCode:
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
29
SIP1 CFBOn SvcCode :
al !
SIP1 CFBOff SvcCode: SIP1 CFNOn SvcCode : SIP1 CFNOff SvcCode: SIP1 ANCOn SvcCode :
st e
SIP1 ANCOff SvcCode: SIP1 VoiceCodecMap : SIP1 BLFList Uri
:
SIP1 BLF Server
:
SIP1 Respond 182
:0
to
SIP1 Enable BLFList:0 SIP1 Caller Id Type:1 SIP1 Use VPN
:1
SIP1 Enable DND
:0
SIP1 Update Reg Exp:1 SIP1 Inactive Hold :0
3.7
or bi dd en
SIP1 Syn Clock Time:0
IAX2 CONFIG MODULE
IAX2 CONFIG MODULE MODULE includes IAX2 registration parameter configuration. IAX2 CONFIG MODULE Name
Description
Server Address
IAX2 registered server address.
Server Port
IAX2 registered server listening on port. The default value is 4569
User Name
IAX2 authentication account user name.
User Password
,f
IAX2authentication account user password.
User Number
IAX2 authentication account user number.
Voice Number
IAX2 voice mail number. The default value is 0,disable
Voice Text
ile
IAX2 voice mail text. The default value is mail
nv
il f
EchoTest Number
Enable the echo test number support platform.If the value is 1, platform support ring, ring call number to text format, then the unit configuration this loopback test number instead of actual text action number;If the value is 0, is not enabled loopback function.This function is to point to through the platform, the terminal can be loopback call test, check the terminal to platform is normal.The default is 1, enabled. The echo test the text of the number.The default for the echo.
Local Port
IAX2 local listener port.The default is 4569.
Enable Register
Enable the IAX2 account registration.If the value is 1, will be to a service to a registered;If the value is 0, is not registered or have registered to the server will be launched to cancel the registration.The default value is 0, is not enabled.
fa
EchoTest Text
Refresh Time
IAX2 Registration update interval time, the unit is in seconds. The
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
30
default value is 60 Enable G.729
st e
al !
To enable support for G.729.If the value is 1, the terminal sends the codec support g. 729.If the value is 0, is not enabled.The default value is 0, is not enabled. Note: if you use the idefisk (does not support G.729), and then call idefisk will cause your PC crash :
Server Port
:4569
User Name
:
User Password
:
User Number
:
Voice Number
:0
Voice Text
:mail
EchoTest Number
:1
EchoTest Text
:echo
Local Port
:4569
Enable Register
:0
Refresh Time
:60
Enable G.729
:0
3.8
or bi dd en
Server Address
to
Example：
MCAST CONFIG MODULE
MCAST CFG MODULE Name
Description
Priority, set the priority of ordinary conversation with multicast A value of 1, is disabled When the value is 0, common calls priority is higher than any multicast; The value is 1, common calls multicast priority is lower than the serial number is 1, higher than any other multicast; Value is 2, common calls the priority below the serial number is 1, 2, multicast, higher than any other multicast; The priority of the value of 3, common calls below the serial number for 1, 2, 3, multicast, higher than any other multicast; The priority of the value of 4, common calls below the serial number is 1, 2, 3, 4, multicast, higher than any other multicast, and so on Value is 9, common calls the lowest priority The default value is 0
nv
il f
ile
,f
Priority
fa
Enbale Priority
Enable Page priority Value is 1, said open this function, multicast will be sorted by the current Page, in the first priority, can call waiting order in the multicast; Value is 0, said is not enabled, multicast will be sorted by the current Page, in the high priority
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
31
The default value is 0 Multicast port Settings, configuration, together with the Host configuration multicast port information in detail, can receive the matching port information from the sponsors of the multicast, the default value is 0
MCAST1 Name
Multicast display name set, when receiving the multicast, the name of the display on the LCD
MCAST1 Host
Multicast band set, together with the port value configuration, can receive the same band port sponsors of multicast
st e
al !
MCAST1 Port
:0
Enbale Priority
:0
--Mcast Addr--
:
MCAST1 Port
:0
MCAST1 Name
:
MCAST1 Host
:
3.9
or bi dd en
Priority
to
Example：
PPPoE CONFIG MODULE
PPPoE CONFIG MODULE mainly contains PPPoE network access parameters configuration. PPPoE CONFIG MODULE Name
Description
Set PPPoE user name. the defaut is user123
PPPoE User
Set PPPoE user password. The default is password
PPPoE Password
Set
the
PPPoE
server
circumstances
can
automatically
search
,f
PPPoE Svc Name
need
the
name.If not
PPPoE
there
set,
is
the
server
no
special
terminal in
the
can
network
address.The default for ANY
Example： PPPoE User
Set PPPoE server address.
ile
PPPoE IP Address
:user123
:password
il f
PPPoE Password
:ANY
PPPoE IP Address
:
nv
PPPoE Svc Name
3.10
MMI CONFIG MODULE
MMI CONFIG MODULE parameters including web pages and TELNET access security Settings.
fa
MMI CONFIG MODULE Name
Description
Telnet Port
TELNET protocol port Settings.The default port is 23, you can access by Telnet commands directly to the end.If the modification for the
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
32
al !
custom port, please pay attention to the best set port is greater than 1024 to avoid port conflicts;After the custom port access require explicit carry port access;After the custom port need to restart the The HTTP protocol port Settings.The default port is 80, can be directly through the browser address input terminal IP access.If the changes for the custom port, please note please set port is greater than 1024 to avoid port conflicts;After the custom port access require explicit carry port access;After the custom port need to restart the unit.
Web Server Type
Access Web of server type protocol Settings.If 0, said need through HTTP access web pages;If is 1, said need via HTTPS access web pages.The default is 0, enable HTTP.Restart to take effect
Https Web Port
The HTTPS protocol WEB port Settings.The default port is 443, can be directly through the browser address input terminal access at https://IP.If the changes for the custom port, please note please set port is greater than 1024 to avoid port conflicts;After the custom port access require explicit carry port access;After the custom port need to restart the unit to work;If you use the HTTPS protocol, need to upgrade the HTTPS certificate, otherwise does not guarantee that the unit can be normal use HTTPS.
or bi dd en
to
st e
Web Port
Remote Control
To enable remote access functions.If the value is 1, said terminal can be access through the WAN;If the value is 0, said WAN port terminal is not permitted to access.The default is 1, enabled
Enable MMI Filter
,f
Telnet Prompt
To enable web filtering capabilities.If the value is 1, you need to specify the IP section, only through the web access IP segment host;If the value is 1, do not specify the IP section, all host cannot be accessed via the web.If the value is 0, is not enabled.The default is 0, disable TELNET Prompt.After setting, through TELNET command to connect on the phone display after the prompt information， Terminal access user name.Support web page, such as Telnet access.Support ninja team multiple users, and distribution permissions.The default is admin
ile
Account1 Name
il f
Account1 Password Account1 Level
Terminal access password. The default value is admin user Lever.If the value is 10, said user with ROOT lever;If the value is 5, said the user with a guest user lever.The default is 10, the administrator lever
nv
Example：
:23
Web Port
:80
Web Server Type
:0
fa
Telnet Port
Https Web Port
:443
Remote Control
:1
Enable MMI Filter :0 Telnet Prompt
:
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
33
:
Account1 Name
:admin
al !
--MMI Account--
Account1 Level
:10
Account2 Name
:guest
Account2 Password :guest Account2 Level
3.11
:5
QOS CONFIG MODULE
st e
Account1 Password :admin
QOS CONFIG MODULE
to
QOS CONFIG MODULE mainly includes the detailed configuration of VLAN related function. Description
Enable VLAN
Enable VLAN.If the value is 1, said enable VLAN, VLAN exchange opportunities based on the VLAN ID divided into different VLAN network;If the value is 0,disable
Enable diffServ
To enable QoS data difference service.The default value is 0, is not enabled
LLDP Transmit
Enable LLDP transmit . the default is 0,disable
LLDP Refresh Time
LLDP Learn Policy
Sends LLDP a refresh packet interval time.In the case of enabling QoS, according to the set time interval to update the LLDP.The default is 60, the unit is in seconds Enable LLDPlearning function, the automatic learning exchange of QoS, VLAN ID, etc. The value of the configuration.The default is 0, is not enabled
Singalling DSCP
,f
SIP singaling DSCP value configuration, in the SIP packet network layer DSCP values is the hex value . the default is 1
Voice DSCP
SIP voice DSCP, In RTP packets DSCP values of the network layer is the hex value , the default is 46 WAN port VLAN ID configuration. The default value is 256
ile
VLAN ID
or bi dd en
Name
Set Signalling Priority. The value is range of 0-7 . the default value is 0
Voice Priority
Set Audio 802.1Ppriority. the value is range of -7. The default is 0
VLAN Recv Check
VLAN ID matching strict inspection.If the value is 0, no more data packets in WLAN carry VLAN ID is same, can be processed;If the value is 1, enable matching strict inspection.The default is 0, disable
nv
il f
Signalling Priority
fa
Enable PVID
LAN port VLAN configuration.If the value is 1, disable the LAN port VLAN, LAN port equipment cannot be assigned to the VLAN ID, and other VLAN devices can not communicate; If the value is 2, enable the LAN port VLAN, LAN port equipment will be assigned to the VLAN ID, to be able to communicate with VLAN ID in the same equipment; If 0, equipment can be assigned to the WAN VLAN Settings under the LAN port VLAN ID and be able to communicate with VLAN devices.The default is 0,
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
34
PVID Value
al !
LAN port VLAN ID configuration.Mainly used for to LAN device.The default value is 254
Example：
3.12
or bi dd en
Note: the terminal VLAN function in bridge mode to use.
to
st e
Enable VLAN :0 Enable diffServ :0 LLDP Transmit :0 LLDP Refresh Time :60 LLDP Learn Policy :0 Singalling DSCP :-1 Voice DSCP :46 VLAN ID :256 Signalling Priority:0 Voice Priority :0 VLAN Recv Check :1 Enable PVID :0 PVID Value :254
DEBUG CONFIG MODULE
The DEBUG CONFIG MODULE mainly contains the syslog MGR, SIP, IAX2 log level Settings.Specific include eight log level (0 to 7) respectively as follows: 0 - none, 1 - alert, 2 - critical, 3 - error, 4 - warning, 5 - notice, 6 - info, 7 - the debug. DEBUG CONFIG MODULE Name
Description
MGR Trace Level
Set MGR trace level.The default is 0，none
SIP Trace Level
Set SIP trace level. The default is 0，none
IAX Trace Level
Set IAX2trace level. The default is 0，none
Trace File Info
Trance file and line number display . the default is 0, disable
,f
Enable watch dog. If the value is 1, unpredictable sudden situation lead to terminal crashed, can’t be used properly, the terminal can automatically restart in order to ensure the normal use; if the value I 0, disable. The default is 1, enabled.
ile
Enable Watch Dog
Example：
:0 :0 :0 :0 :1
nv
il f
MGR Trace Level SIP Trace Level IAX Trace Level Trace File Info Enable Watch Dog
AAA CONFIG MODULE
fa
3.13
Triple CONFIG MODULE mainly includes the syslog related Settings, syslog is mainly used for phone problem debugging, tracking and positioning, etc. AAA CONFIG MODULE
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
35
Description
Enable Syslog
Enable Syslog.If the value is 1, the terminal will conform to the conditions of the log information display on the specified in the syslog, if the value is 0, is not enabled syslog function.The default is 0, is not enabled.
Syslog address
Set the syslog computer's IP address.
Syslog port
Set the syslog port.The default value is 514
3.14
:0 :0.0.0.0 :514
ACCESS CONFIG MODULE
to
Enable Syslog Syslog address Syslog port
st e
Example：
al !
Name
or bi dd en
ACCESS CONFIG MODULE used for dispensing firewall MODULE, mainly through the web to configure terminal. ACCESS CONFIG MODULE Name
Description
Enable In Access
Enable in access rules.If the value is 1, the rules of the remote IP terminal can not access to the local terminal, but local terminal can access remote IP terminal;If the value is 0, said is not enabled rules.The default is 0, disabled
Enable Out Access
Example：
,f
Enable In Access :0 Enable Out Access :0
To enable the output access rules. If the value is 1, local terminal of remote IP terminals cannot access rules, but a remote terminal can access local terminal; If the value is 0, said is not enabled rules. The default is 0, disabled
DHCP CONFIG MODLUE
il f
3.15
ile
Note: all the rules is only aimed at the terminal effect in rules, has no effect on the rules of the terminal
DHCP CONFIG MODULE
Description
DHCP Server Type
Lan port under the DHCP service status The value is 1, said LAN mouth enable DHCP service When the value is 0, means LAN shut down the DHCP service Value of 2, means enable DHCP relay agent The default value is 1, enable the DHCP service
fa
nv
Name
DHCP Relay IP
When a DHCP server type, type is 2 the IP address of the relay
Enable DNS Relay
Value is 1, the enabled DNS Relaey When the water is 0, the DNS Relaey
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
36
The default value is 1, enabled Set up automatic upgrade configuration items When the value is 0, shut off the automatic update function The value is 1, enabled the automatic upgrade the firmware Value of 2, enabled automatically upgrade the function of the configuration file The default value is 0, disabled the automatic update function
Update TFTP SRV IP
Indicates that the use of automatic updates the address of the TFTP server
st e
al !
Update SRV Mode
Example： DHCP Relay IP
:
Enable DNS Relay
:1
Update SRV Mode
:0
Update TFTP SRV IP :0.0.0.0
3.16
to
:1
or bi dd en
DHCP Server Type
NAT CONFIG MODULE
NAT CONFIG MODULE Name
Description
Enable Nat
NAT service enable / disable settings
The value is 1, enable NAT service The value is 0, disable NAT service The default value is 1, enable NAT service
Enable Ftp ALG
,f
Enable FTP ALG The value is 1, to enable FTP ALG, able to use this network of IP at the time of contract into the network IP value is 0, disable FTP ALG The default value is 1, enable the FTP ALG
Enable H323 ALG
ile
The value is 1, enable H323 ALG The value is 0, disable H323 ALG The default value is 0,disable H323 ALG version(currently only the configuration items in the configuration file)
il f
Enable PPTP ALG
fa
nv
Enable IPSec ALG
Point-to-point tunel protocol(PPTP) The value is 1, enable the PPTP ALG The value is 0,disable the PPTP ALG The default value is 1, enable the PPTP ALG
Encryption technology to unlock The value is 1, enable the IPSec ALG The value is 0, disable the IPSec ALG The default value is 1, enable the IPSec ALG
Example： Enable Nat
:1
Enable Ftp ALG
:1
Enable H323 ALG
:0
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
37
:1
Enable IPSec ALG
:1
PHONE CONFIG MODULE
PHONE CONFIG MODULE
st e
3.17
al !
Enable PPTP ALG
Description
Menu Password
According to the value of the set menu for the password, enter the advanced Settings on the LCD need to enter a password The default value is 123
KeyLock Password
Display value is set by the keyboard lock password, keyboard lock, enter the password can unlock the keyboard lock, can be operation for any key The default value is 123
Enable KeyLock
or bi dd en
Fast Keylock Code
to
Name
Shows the value of the lock for the password, enter the password to lock the keyboard under the standby, locked only after the number keys and a few other buttons (for example, answer, reject the call interface key) The default is an empty Show the current state of the keyboard lock Value is 1, enable the keyboard lock state When the value is 0, disable the keyboard lock state The default value is 0, disable the keyboard lock
Emergency Call
Emergency call number Under the open state of the keyboard lock can exhale set emergency call number The default value is 110
LCD Title
ile
,f
Greeting words Greeting contents of display Settings, the default value for VOIP PHONE
il f
LCD Constrast
nv
LCD Luminance
fa
Backlight Off Time
Enable Power LED
Contrast Contrast value of the current phone screen, LCD's definition according to the contrast values change The default value is 5 Backlight The value is 1, backlight open, the screen backlight within the set Off Time value is highlighted Value is 0, the backlight closed, the screen backlight for darkness The default value is 1, the backlight enable
Backlight off timeout time enable backlight, it will set at certain timeout period is highlighted, the phone unoperation, after more than setting value, phone backlight dimming The default value is 30 s Set the power light
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
38
st e
al !
Value is 1,the power LED is light, the standby power supply, light red light long on call, power red light flash, have not call/not read information, the power light slow flash a red light value is 0, the supply the lamp is off, standby power supply when the lamp is destroyed, calls, power red light flash, have not call/not read information, the power light slow flash a red light The default value is 0, the power off state Time display format When the value is 0, the time to 24 hours style for display The value is 1, time to 12 hours style for display The default value is 0, in 24 hours style for display
Enable TimeDisplay
Time display (the current version does not support this function) Value is 1, enable time display, according to the phone can display the standby time The value is 0, disable time display, according to the phone does not display the standby time The default value is 1, enable time display
or bi dd en
to
Time Display Style
Phone Model
Phone model Show the current phone models, for example, C62 phones and it displayed value for C62
About Info
The content of the item displayed on the screen about (now the configuration will not work)
Missed Call LED
Alarm Clock
,f
Have Missed call light Value is 1, enable the lamp power supply did not call phone did not call, slow flash a red light to indicate power lamp Value is 0, disable the lamp power supply not call phone when we have not call power lights flashing a prompt The default value is 1, enable the lamp power supply did not call Enable alarm clock. Date display format Value is 0, use the date format is the first one, a total of 14 kinds of formats to choose corresponding value 0-13, respectively The default value is 0, the use of the first date display format
ile
Date Display Style
il f
Date Separator
fa
nv
Enable Pre-Dial
Default Line
Date display separator forms Value is 0, the use of "/" is the first separator forms, a total of four kinds of forms, respectively corresponding value 0 to 3 The default value is 0, the use of the first separator display form Enable predial The value is 1, enable the function of predial, under the standby mode will not enable to receive the number input rules Value is 0, disable function of predial, standby mode will enable to receive the number input rules The default value is 1, disable the predial function The default line selection Show the current phone is used by default which one SIP line, need
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
39
al !
to open the default line selection The default value is 1, using the first SIP enable/disable the default line selection The default value is 1, open line selection function, offhook, handsfree, headphones opened the dial is using the default line When the value is 0, the default line selection function, offhook, hands-free, is the first opened the dial using the headset available line
Enable Auto SelLine
Automatic selection line function The value is 1, enable the function of automatic select line, when the default line unregistered or registered failure, can automatically switch to the available line Value is 0, disable automatically in line function, when the default line unregistered or registered failure, not to switch to other lines The default value is 1, and disable the function of automatic in line
or bi dd en
to
st e
Enable Default Line
Agent Username
Agent username Log on to the Agent to fill in the user name
Agent Password
Agent password Login to use when the Agent user password
Agent Number
Agent number Login to use when the Agent user number
Agent Sipline
Agent SIP line When login to the Agent, the use of SIP, the first SIP line 0 corresponding is, 1 corresponding is the second SIP lines, and so on The default value is 0, the first SIP line is used
Agent Status
ile
,f
State of the Agent When the value is 0, it is state of logon The value is 1, is logoff state Value is 2, it is UNAVAILABLE state Value is 3, is the AVAILABLE state Value is 4, is WRAPUP state The default value is 0, is logon status
il f
LDAP1 Title
nv
LDAP1 Server
fa
LDAP1 port
The name of the LDAP phonebook Set the name of the LDAP telephone, enter the LDAP applications through LCD, you can see the set of values The default is empty
LDAP server Input LDAP server, click the LDAP to login to the server access to the LDAP directory. The default value is null The LDAP server port value Fill in the LDAP server corresponding port value, the unit can change port value access server to get the phone book The default port values for 389
LDAP1 Authenticate
The LDAP authentication Value is 0, the choice of authentication for no, anonymous access
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
40
st e
al !
Value is 1, the selected authentication way to DIGEST - MD5, with the user name password Value of 2, choose the authentication way to CRAM - MD5, with the user name password Value of 4, the choice of authentication method is simple, with a user name password The default value is 0, to choose understanding way, anonymous access LDAP version Value is 3, chosen is version 3 Value of 2, choose the version 2 The default value is 3, choose the version 3
LDAP1 Calling Line
LDAP calling line Value is 0, using the automatic line, through the LDAP directory to create default to the current line calls Value is 1, using the SIP1, build calls by LDAP directory, default to SIP1 lines Value of 2, using the SIP2, through LDAP telephone this set up on the phone, the default SIP2 lines The default value is 0, using the automatic
LDAP1 Base
or bi dd en
Enable LDAP Call the query Value is 1, enable automatically call query function, when breath/call search contacts in the name of the LDAP server Settings,, if the search is displayed on the screen.Priority is the local phone book - > LDAP directory - > SIP displaynam to carry Value is 0, dsiable automatically call query function, when breath/call does not search contacts in the name of the LDAP server Settings The default value is 0, disable automatically query function
,f
LDAP1 Enable Search
to
LDAP1 Version
The root of the query LDAP username Show the login user name used by the LDAP
ile
LDAP1 Username
LDAP password Show the login of LDAP user password
LDAP1 Tel Attr
Match the properties of the telephone, the default value is telephoneNumber, can filter out under contact number attribute for telephoneNumber number
il f
LDAP1 Password
nv
LDAP1 Mobile Attr
Matching Mobile properties, the default value is Mobile, can filter out under contact number attribute for the Mobile number Match the Other properties, the default value is home, showed the home phone number
LDAP1 Displayname
Value is the cn, can display the contact name, normal for other values or empty, can not display the contact name, can display the phone number
fa
LDAP1 Other Attr
XML-PBook1 Name
The name of the network the phonebook Display Settings, according to the network when the phone book to fill
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
41
al !
in by LCD can see when you enter a network phone book application name disp The address of the network the phonebook Display Settings network server that USES the phone book, IP address, name of the phonebook file
XML-PBook1 Auth
network phonebook this user name and password Display Settings of network when the phone book to fill in the user name and password
XML-PBook1 Policy
Authentication of LDAP directory (LDAP directory after independence, the configuration items temporarily doesn't work) Value is 0, the choice of authentication for no, anonymous access Value is 1, the selected authentication way to DIGEST - MD5, with the user name password Value of 2, choose the authentication way to CRAM - MD5, with the user name password Value of 4, the choice of authentication method is simple, with a user name password The default value is 0, to choose understanding way, anonymous access Use SIP line network phone book When the value is 0, the use of automatic line, the phone book to establish communication through the network, the default to the current line Value is 1, using the SIP1, the phone book to establish communication through the network, the default use SIP1 lines Value of 2, using the SIP2, the phone book to establish communication through the network, use the default SIP2 line, and so on The default value is 0, using the automatic
,f
XML-PBook1 Sipline
or bi dd en
to
st e
XML-PBook1 Addr
The contact group Show the current name of the telephone all people groups The default has six groups, each friend, home, work, business, classmate, colleague
ile
Phonebook Groups
fa
nv
il f
Fkey1 Type
Fkey1 Value
Button type When the value is 0, the function key type to none, without any function When the value is 1, the function key type for the Memory key Value of 2, function key type for the Line key Function, when the value of 3 Key type of Key Event Value is 4, function key types of DTMF Function, when the value of 7 key type of UR Value is 13, function Key types of BLF List Key Value is 14, for Multicast function key type The value of the function keys Shows the configured function key Value, the Line, Subtype, Pickup Number Value
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
42
Can be displayed on LCD and the name of the function keys (now the configuration will not work)
exKey1 Type
Expansion board button type When the value is 0, the function key type to none, without any function When the value is 1, the function key type for the Memory key Value of 2, function key type for the Line key Function, when the value of 3 Key type of Key Event Value is 4, function key types of DTMF Function, when the value of 7 key type of URL Value is 13, function Key types of BLF List Key Value is 14, function key type of Multicast
exKey1 Val
The value of the function keys Shows the configured function key Value, the Line, Subtype, Pickup Number Value
exKey1 Name
or bi dd en
to
st e
al !
Fkey1 Title
Can be displayed on LCD and the configuration of the name of the function keys (now the configuration will not work)
Example： Menu Password
:123
KeyLock Password
:123
Fast Keylock Code : Enable KeyLock
:0
Emergency Call
:110
LCD Title
:VOIP PHONE
LCD Constrast
:5
LCD Luminance
:1
Backlight Off Time :30 :0
,f
Enable Power LED
Time Display Style :0 Enable TimeDisplay :1
:C62
About Info
:
ile
Phone Model
Missed Call LED
:1
Alarm Clock
:0,,1
il f
Date Display Style :0
:0
Enable Pre-Dial
:1
Default Line
:1
nv
Date Separator
Enable Default Line:0 Enable Auto SelLine:1 :
Agent Password
:
Agent Number
:
Agent Sipline
:0
Agent Status
:0
fa
Agent Username
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
43
:
LDAP1 Title
:
LDAP1 Server
:
LDAP1 port
:389
al !
--LDAP Config--
LDAP1 Authenticate :0 :3
st e
LDAP1 Version
LDAP1 Calling Line :0 LDAP1 Base
:
LDAP1 Username
:
LDAP1 Password
:
LDAP1 Tel Attr
:telephoneNumber
to
LDAP1 Enable Search:0
LDAP1 Mobile Attr :mobile LDAP1 Other Attr
:home
--Xml PhoneBook-- : XML-PBook1 Name
:
XML-PBook1 Addr
:
XML-PBook1 Auth
:
XML-PBook1 Policy :0 XML-PBook1 Sipline :0
or bi dd en
LDAP1 Displayname :cn
Phonebook Groups
:friend,home,work,business,classmate,colleague
--Function Key--
:
Fkey1 Type
:2
Fkey1 Value
:SIP1
Fkey1 Title
:
--Extern Console-- : :0
exKey1 Val
:
exKey1 Name
:
ile
3.18
,f
exKey1 Type
SCREEN KEY CONFIG MODULE
il f
SCREEN KEY CONFIG MODULE mainly includes the softkey navigation button and the SCREEN configuration. SCREEN KEY CONFIG MODULE
nv
Name
Desktop Softkey
Description Desktop
softkey
configuration . the default
is history; contact; dnd;
menu； Talking softkey configuration . the default is hold; xfer; conf; end;
Ringing Softkey
Ringing softkey configuration .the default is accept; none; cfwd; reject;
Alerting Softkey
Alerting softkey configuration. The default is none; none; none; end;
XAlerting Softkey
Transfer alerting softkey configuration .the default is xfer; none; none; end;
Conference Softkey
Conference talking softkey configuration .the default is hold; none; split;
fa
Talking Softkey
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
44
end; Hold waiting softkey configuration .the default is hold;xfer;conf;end;
Ending Softkey
Another call end the talking call ,local ending softkey configuration. Default is repeat; none; none; end;
DialerPre Softkey
Dialer pre softkey configuration. The default is delete; save; send; exit;
DialerCall Softkey
Dialer call softkey configuration .the default is delete; none; send; exit;
DialerXfer Softkey
Dialer transfer softkey configuration . the default is delete; xfer; send; exit;
DialerCfwd Softkey
Dialer forward softkey configuration . the default is delete; none; cfwd; exit;
Desktop Click
The active navigation key press event corresponding configuration. By default the history;The status; Paccout; Naccout;The menu; Corresponding navigation keys of up, down key, to the left, to right click the OK button
Dailer Click
The talking navigation key press event corresponding configuration.The default is pline;Nline;None;None;None;Corresponding navigation keys of up, down key, to the left, to right click the OK button The talking navigation key press event corresponding configuration.The default value is: pcall;Ncall;Voldown;Volup;None;Corresponding navigation keys of up, down key, to the left, to right click the OK button
Desktop Long Press
Softkey Mode
Desktop long navigation key press event corresponding configuration.By default the status;None;None;Sdial;None;Corresponding navigation keys of up, down key, to the left, to right click the OK button Softkey use mode.If the value is 0, said not to use a custom softkey, directly use the default softkey;If the value is 1, expressed support for custom softkey, support more than 4 softkey shows at the same time;If the value is 2, expressed support for softkey, but the screen can only display on four softkey, beyond the number will not be displayed.The default is 1
,f
Example：
st e
to
Click
or bi dd en
Call
al !
Waiting Softkey
:history;contact;dnd;menu;
Talking Softkey
:hold;xfer;conf;end;
Ringing Softkey
:accept;none;cfwd;reject;
Alerting Softkey
:none;none;none;end;
ile
Desktop Softkey
XAlerting Softkey :xfer;none;none;end;
il f
Conference Softkey :hold;none;split;end; Waiting Softkey
:hold;xfer;conf;end;
Ending Softkey
:repeat;none;none;end;
DialerPre Softkey :delete;save;send;exit;
nv
DialerCall Softkey :delete;none;send;exit; DialerXfer Softkey :delete;xfer;send;exit; DialerCfwd Softkey :delete;none;cfwd;exit;
fa
Desktop Click
:history;status;paccout;naccout;menu;
Dailer
Click
:pline;nline;none;none;none;
Call
Click
:pcall;ncall;voldown;volup;none;
Desktop Long Press :status;none;none;sdial;none; Softkey Mode
:1
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
45
al !
3.19
AUTOUPDATE CONFIG MODULE
st e
AUTOUPDATE CONFIG MODULE includes PnP, Phone Flash, Option66 automatic update of detailed configuration, etc AUTOUPDATE CONFIG MODULE Description
Download Username
Automatic update server user name.Mainly used in automatic upgrade process using set user name to the corresponding FTP, HTTP and HTTPS authentication
Download Password
Automatic update server password.
Config File Name
Configuration file name.Need to download a configuration file name specified
Config File Key
Encryption key configuration file.
Download Server IP Download Protocol
Download Mode
The key of common configuration file Automatic update server address
Automatic update the protocol used if the value is 1, use the FTP protocol;If the value is 2, using the TFTP agreement;If the value is 4, using the HTTP protocol;If the value is 5, using the HTTPS protocol.The default is 1, use the FTP protocol Automatic upgrade pattern configuration.If the value is 0, not to upgrade;If the value is 1, restart after the upgrade, after restart the unit can automatically download information to obtain, download the update item;If the value is 2, according to certain update interval, interval every once in a while to get updated information, if there are any updates to download.The default value is 0, no update Automatic update interval time .If set interval every once in a while to get updated information, if there are any updates to download
,f
Download Interval
The DHCP mode Option.If the value is 0, disable DHCP Option;If the value is 66, using the Option 66;If a value of 43, use Option 43;If the value is between 128-254, using a custom DHCP Option.The default value is 66, using the Option 66 model
ile
DHCP Option
or bi dd en
Common Cfg File Key
to
Name
il f
PNP Enable
The PNP function.If the value is 0, close the PNP function;If the value is 1, enable the PNP function.The default is 1, enable the PNP function The PNP server address.Show the PNP server address
PNP Port
PNP server listener port configuration.The default value is 5060
PNP Transport
The PNP protocol.If the value is 0, use the UDP protocol;If the value is 1, using the TCP protocol.The default value is 0, use the UDP protocol
fa
nv
PNP IP
PNP Interval
The PNP interval.If display values set by the PNP cycle, opportunity value every cycle to get updated information, if there are any updates to download.The default value is 1 (h)
Save Provision Info
Save updates automatically.If the value is 0, the is not saved
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
46
st e
al !
automatically update information;If the value is 1, save the automatic updates, to preserve the unit automatically upgrade when input configuration information (for example, a user name, password, custom file ID value, etc.), phone upgrade again, don't have to manually enter again.The default value is 0, do not save updates automatically Example： Download Username : Config File Name
:
Config File Key
:
to
Download Password :
Common Cfg File Key: Download Server IP : Download Mode
:0
Download Interval :1
or bi dd en
Download Protocol :0
DHCP Option
:66
PNP Enable
:1
PNP IP
:224.0.1.75
PNP Port
:5060
PNP Transport
:0
PNP Interval
:1
Save Provision Info:0
3.20
VPN CONFIG MODULE
The VPN CONFIG MODULE mainly includes two OpenVPN and L2TP VPN configuration in detail.
,f
VPN CONFIG MODULE Name
Description
VPN mode
ile
VPN using mode.If the value is 0, using UDP Tunnel;If the value is 1, use L2TP;If the value is 2, the use of OpenVPN.The default value is 2, the use of OpenVPN
L2TP LNS IP
il f
L2TP server ip address，support IPv4 address mode L2TP user name
L2TP Password
L2TP password
Enable VPN Tunnel
Enable VPN. if the value is 1, means can Enable the corresponding OpenVPN or L2TP functions;If the value is 0, means disable VPN.The default value is 0, disable
nv
L2TP User Name
UDP Tunnel server ip address. the default is 0.0.0.0
VPN Server Port
UDP Tunnel server port . the default is 0
fa
VPN Server IP
Server Group ID
VPN server group id (abandon)
Server Area Code
VPN server area code(abandon)
Example： VPN mode
:2
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
47
:
L2TP User Name
:
L2TP Password
:
al !
L2TP LNS IP
VPN Server IP
:0.0.0.0
VPN Server Port
:80
Server Group ID
:VPN
Server Area Code
:12345
DOT1X CONFIG MODULE
DOT1X CONFIG MODULE mainly includes details of 802.1 X DOT1X CONFIG MODULE Description
Xsup User
or bi dd en
Name
802.1 Authentication user name
Xsup Password
802.1X Authentication user password
Xsup Enable
Enable the 802.1 X authentication.The default is 0, disable;If the value is 1, enable
Xsup AuthMac
802.1X authentication for mac address
Xsup UseDefaultMac Example：
Enable 802.1X use default mac authentication mode. The default is 0,disable
Xsup User
:admin
Xsup Password
:admin
Xsup Enable
:0
Xsup AuthMac
:01:80:C2:00:00:03
,f
Xsup UseDefaultMac :0
TR069 CONFIG MODULE
ile
3.22
to
3.21
st e
Enable VPN Tunnel :0
TR069 CONFIG MODULE mainly include telecom and standard TR069 server configuration in detail TR069 CONFIG MODULE
il f
Name
nv
ACS Server Type
fa
ACS URL
Description The ACS server type, if the value is 0, compatible with telecom (CTC) ACS server;If the value is 1, compatible with standard (Common) ACS server.The default is 1 ACS authentication server address, set the ACS certification service complete address, used to use the ACS certification.The default is 0.0.0.0
ACS UserName
ACS user name.The ACS server authentication
ACS Password
ACS user password.The ACS server authentication
CPE UserName
CPE user name.The ACS server authentication
CPE Password
CPE user password.The ACS server authentication
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
48
Equipment serial number
TR069 Auto Login
Enable TR069 automatic connection.If the value is 1, startup will automatically connect the ACS server, and launch a certification;If the value is 0, boot will not automatically launch certification.The default is 0, is not enabled
Enable TR069
Enable TR069 function.If the value is 1, the terminal will be launched an authentication, the ACS server configuration management for terminal;If the value is 0, said don't use TR069 function.The default is 0, is not enabled
Periodix Interval
CPE send packet interval time l.The default is 3600, the unit is in seconds.
Area Code
Area code.
Example： :1
ACS URL
:0.0.0.0
ACS UserName
:admin
ACS Password
:admin
CPE UserName
:dps
CPE Password
:dps
CPE SerialNumber
:00100400XH020010000000010e597052
TR069 Auto Login
:0
Enable TR069
:0
Periodix Interval :3600 :020
fa
nv
il f
ile
,f
Area Code
or bi dd en
ACS Server Type
to
st e
al !
CPE SerialNumber
© 2012 Fanvil Co., Ltd. This document contains information that is proprietary to Fanvil Co., Ltd. Unauthorized reproduction or disclosure of this information in whole or in part is strictly prohibited.
49
