Transcript
the conversion technology experts Fast Ethernet Media Converter
■ Automatically detects faults in a link using Far End Fault. The feature of the Fast Ethernet Fiber standard allows you to troubleshoot a fault, even if it is only in one direction; alerting the device on the same side as the failure. ■ The converters will also automatically reestablish link when connected to two 10/100 auto-negotiating switches if link is lost. With other manufacturers’ converters the user must intervene to re-establish link.
100BASE-TX to 100BASE-FX Media Converter With Transition Networks’ full-featured 100BASE-TX to 100BASE-FX Media Converter, cost-effective integration of twisted pair and fiber optics in Fast Ethernet networks is easier than ever before. Features ■ Operates under heavy traffic loads without excess heat, so there is no need for a failureprone internal fan. ■ Round trip delay of only 40 bit times—far below the Class II rating of 92 bit times. ■ N-Way Auto-Negotiation Only Transition Networks guarantees compatibility with any 10/100 compliant port. This feature allows you to force the proper port configuration through an external switch on the converter, unlike competitive products that ship in auto-negotiation mode and may require both hardware and software configuration.
■ Pause is a component of Auto-Negotiation and because Auto-Negotiation is not supported over a fiber link, switches cannot utilize this flow control feature without our converters. Enabling the Pause feature on the converters between two switches allows users to take advantage of this flow control feature on their equipment. Applications Extend Network Distance in Full-Duplex Networks: Used in pairs, this media converter can extend distances between two twisted pair switches or a switch and a server up to 2,000 meters over multimode fiber or up to 80,000 meters over single mode fiber. Connect Remote Devices: Using one media converter, a switch with a copper port can be connected to a switch with an existing fiber interface.
■ Automatically detects and reports loss of link on a connection using Link Pass Through. This feature allows the equipment at the remote end of a link failure to "see" this failure and respond with corrective actions, such as Spanning Tree fail-over links, proprietary trunking links, or failure reports through SNMP or RMON procedures built into the switch, router or hub.
Transition Networks, Inc. 6475 City West Parkway Minneapolis, MN 55344 USA
tel 952.941.7600 or 800.526.9267 fax 952.941.2322
[email protected] http://www.transition.com
100BASE-TX to 100BASE-FX Media Converter Specifications
Dimensions: 3.0" x 4.7" x 1.0" (76 mm x 119 mm x 25 mm)
Standards: IEEE 802.3 1998 Edition 100BASE-FX, 100BASE-TX
Power: Stand-Alone Unit: External AC required; +7.5 to 16.0 V DC; .5A, Slide-In-Module: Supplied by chassis
Connectors: 1 RJ-45 (100BASE-TX: 100 meters); 1 duplex fiber optic Switches: SW1: Auto-Negotiation On/Off; SW2: Pause TX On/Off; SW3: LPT On/Off; SW4: FEF On/Off
Operating Environment: 0 – 50˚ C; 5% – 95% humidity non-condensing; 0 – 10,000 feet altitude Shipping Weight: 8 oz. (.2 kg) Compliance: UL Listed; FCC Class A; EN55024; EN55022 Class A; CE Mark
Jumpers: Jumper Block 1: Auto Cross enable; Jumper Block 2: HSTR enable
Warranty: Lifetime
Unit LED: Power: Lit for normal operation Port LEDs: FACT (Fiber Activity): Blinking indicates activity; FLNK (Fiber LInk): Lit indicates Link; TPACT (Twisted Pair Activity): Blinking indicates activity; TPLNK (Twisted Pair Link): Lit indicates Link Fiber Optic Connector Specs Stand-Alone E-100BTX-FX-05 E-100BTX-FX-05(LH) E-100BTX-FX-05(LW) E-100BTX-FX-05(MT) E-100BTX-FX-05(SC) E-100BTX-FX-05(SM) E-100BTX-FX-05(SMLC) E-100BTX-FX-05(XL)
Slide-In-Module C/E-100BTX-FX-05 C/E-100BTX-FX-05(LH) C/E-100BTX-FX-05(LW) C/E-100BTX-FX-05(MT) C/E-100BTX-FX-05(SC) C/E-100BTX-FX-05(SM) C/E-100BTX-FX-05(SMLC) C/E-100BTX-FX-05(XL)
Connector Type ST SC SC MT-RJ SC SC LC SC
Fiber Type Multimode Single Mode Single Mode Multimode Multimode Single Mode Single Mode Single Mode
Wavelength 1300nm LED 1300nm MQW laser 1550nm DFB laser 1300nm LED 1300nm LED 1300nm ELED 1300nm ELED 1300nm laser
Typical Distance 2 km 40 km 80 km 2 km 2 km 20 km 20 km 60 km
Min TX PWR -19.0 dBm -8.0 dBm -5.0 dBm -19.0 dBm -19.0 dBm -15.0 dBm -15.2 dBm -5.0 dBm
Max TX PWR -14.0 dBm -2.0 dBm 0.0 dBm -14.0 dBm -14.0 dBm -8.0 dBm -8.0 dBm 0.0 dBm
Sensitivity -30.0 dBm -34.0 dBm -34.0 dBm -33.5 dBm -30.0 dBm -31.0 dBm -32.5 dBm -34.0 dBm
Max In PWR -14.0 dBm -14.0 dBm -7.0 dBm -7.0 dBm -14.0 dBm -8.0 dBm -3.0 dBm -7.0 dBm
Link Budget 11.0 dB 26.0 dB 29.0 dB 14.5 dB 11.0 dB 16.0 dB 17.3 dB 29.0 dB
6/01 Technical information subject to change without notice.
T R A N S I T I O N networks The Conversion Technology Experts Company Overview Transition Networks designs and manufacturers Conversion Technology products, specializing in media converters. These products help customers, such as AT&T, Internap, Lowes, and Chrysler, cost-effectively deploy fiber by reducing the costs of electronics as much as 40%. Due to the built-in reliability and management features of Transition's Point System Platform, customers can experience these cost savings without jeopardizing the availability of their fiber networks. Our principle of conversion technology is to
Transition Networks, Inc. 6475 City West Parkway Minneapolis, MN 55344 USA
make the necessary adaption while not affecting the performance, nature or appearance of the network to the users or devices. Products Transition Networks develops and distributes media conversion tools that enable today's—and tomorrow's— bandwidth growth requirements. The company's products are designed to protect the investment made in network infrastructure while optimizing its performance capacity. Distribution Transition Networks distributes product exclusively through a network of resellers in North America and 50 countries worldwide. The company also supports key OEM partners that private label its products.
tel 952.941.7600 or 800.526.9267 fax 952.941.2322
[email protected] http://www.transition.com
