Fast Fixing!

Transcript

34 www.ramset.com.au 1300 780 063 Powder Actuated Systems With over 50 years of experience in designing and manufacturing powder actuated tools and consumables, Ramset™ Powder Actuated fastening systems are innovative, powerful, easy to use and specifically designed for Australian applications. These tools provide a fast fixing method for fastening many common building materials to concrete, masonry and steel. Tools in this range include: • FrameMaster™ (TS750P) • FormMaster™ • FrameBoss™ • TyMaster™ • Rocket www.ramset.com.au 1300 780 063 35 Powder Actuated Systems 36 www.ramset.com.au 1300 780 063 Contents Powder Actuated Systems Fastening Principles 38 Selection Guide 40 FrameBoss™ 42 Rocket 46 FrameMaster™ (TS750P) 48 FormMaster™ 50 TyMaster™ 52 Drive Pins & Power Loads www.ramset.com.au 56 1300 780 063 37 Fastening Principles Powder Actuated Systems Powder Actuated Technology - How it works Fastening Principles Ramset™ Powder Actuated Technology uses a captive piston to transfer the energy from the power load to the fastener. In this way the majority of any excess energy, which is produced by the power load, is absorbed within the tool by the buffer. Ramset™ Powder Actuated tools are powerful and reliable which allows them to fasten to steel, concrete and masonry year after year. 5 4 3 1. Firing Pin 2. Power Load 3. Captive Piston 4. Buffer 5. Powder Actuated Fastener How to select a Ramset™ Drive Pin to directly fasten an object to CONCRETE Fixing to concrete As the fixing enters the concrete, extreme pressure and heat are created. This creates a bond that provides high loading strength in concrete. Edge distance Do not fix closer than 75mm from the edge of concrete. If the concrete cracks, the fixing may not hold. M Recommended minimum fixing spacing Setting fixings too close together can cause the concrete to crack. The recommended minimum distance between fixings is 75mm. Never attempt a fixing application too close to another fixing as this could affect the previously inserted fixing’s embedment. Concrete thickness It is important that the concrete be at least three times as thick as the fixing penetration. If the concrete is too thin, the compressive forces forming at the fixing’s point can cause the free face of the concrete to break away. This creates a dangerous condition from flying concrete and / or the fixing and also results in a reduction of fastener holding power. Minimum Shank Length Thickness + of material (M) 25mm How to select a Ramset™ Drive Pin to directly fasten an object to STEEL Fixing to steel The resilience of steel provides a clamping effect to the fixing. This combined with the tremendous heat that is created, provides a welding and clamping effect to give maximum holding power. M Edge distance The recommended edge distance for a fixing to the edge of steel is 13mm. Never fire the tool within 13mm of the edge of a steel base material because the steel may bend or break off, allowing the fixing to ricochet. T Recommended minimum fastener spacing The recommended minimum distance between fixings is 25mm. Never attempt a fixing application too close to another fixing as this could affect the previously installed fixing’s embedment. Steel thickness Do not fasten into steel base material thinner than the fastener shank diameter. Holding power may be reduced and the fastener may be overdriven. As a guide when: • Fixing into steel - min. steel thickness = 4mm 38 www.ramset.com.au 1300 780 063 Minimum Shank Length Thickness + of material (M) Steel Thickness (T) + 6mm point allowance 2 1 Notes Powder Actuated Systems www.ramset.com.au 1300 780 063 39 Selection Guide Powder Actuated Systems 40 25 to 25 to 100mm 75mm Timber Formwork Pins For Concrete & Easy Pin Removal 56 60 to 60 to 100mm 75mm Premium Drive Pins For Structural Steel 57 25 to 75mm Washered Drive Pins For Concrete , Masonry & Steel 57 25 to 75mm 4 4 4 4 4 4 4 25 to 50mm 4 25 to 75mm 4 4 4 (TS750P) 4 60 to 60 to 75mm 100mm ▲ 25 to 75mm ● 4 4 4 4 25 to 75mm 4 ▲ 60 to 75mm ▲ 25 to 75mm ● 4 25 to 75mm JobMaster™ FrameMaster™ 4 25 to 25 to 25 to 75mm 100mm 32mm ▲ 4 25 to 75mm TyMaster™ 56 FormMaster™ Standard Drive Pins For Concrete, Masonry & Steel Rocket (FrameBoss) FrameBoss™ (FrameBoss75) Product Range FrameBoss™ 42 42 46 48 50 52 54 Page Reference Powder Actuated Systems 4 Recommended ● Maybe possible dependant on substrate ▲ Not suitable 4 4 25 to 32mm 25 to 75mm 25 to 75mm 25 to 32mm 25 to 75mm ▲ ▲ ▲ ▲ ▲ Standard Collated Drive Pins For Concrete, 44 Masonry & Steel 25 to 75mm Premium Collated Drive Pins For Concrete, 44 Masonry & Steel 25 to 75mm 25 to 60mm ▲ ▲ ▲ ▲ ▲ 4 4 4 25 to 60mm 4 Angle Bracket & Threaded Rod Hanger Assemblies 58 4 4 4 4 ▲ 4 4 Drive Pins For Fixing Thin Steel To Steel 58 4 4 4 4 4 4 4 Drive Pins For Fixing Thin Steel To Steel 58 4 4 ▲ ● 4 ▲ ● Insulation Fasteners For Concrete, Masonry & Steel 45 ▲ With Adaptor ▲ ▲ ▲ ▲ ▲ Soft Washered Membrane Fastener 59 4 4 ▲ 4 4 ▲ 4 www.ramset.com.au 4 1300 780 063 Selection Guide Powder Actuated Systems Fastener Selection and Correct Setting The correct selection and setting of Powder Actuated Fasteners is critical with all tools to ensure a secure fixing and long tool life. The correct setting of the fastener should be as detailed in the diagrams to avoid excessive overdrive and a secure fix.­ PIN Part No. PIN Part No. LWU75 SP12 LDU75 SP12 Powder Actuated Systems Where possible, a washer (Part No: RCD16F) or a washered fastener should be used. (Application permitting, to reduce overdrive and produce maximum clamping force). Repeated excessive overdrive will result in damage and short life of tool parts. RDU99 SC925 SC930C SC930C SC925C SC930 SC930 SC950C SC960C PIN Part No. LWU75 LDU75 RDU99 Powerload Selection Guide - Concrete Tool FrameBoss™ FrameMaster™ TS750P FormMaster™ JobMaster™ TyMaster™ Rocket 20 MPa Concrete Low Strength PLSGR22 PLSGR22 PLSGR22 PLCGR22S PLSGR22 PLSGR22 30 MPa Concrete Medium Strength PLSYW22 PLSYW22  PLSYW22   PLCYW22S  PLSYW22    PLSYW22  40 MPa Concrete High Strength PLSRD22 PLSRD22 PLSRD22 PLCRD22S PLSRD22 PLSYW22 This chart is to be used as a guide only. Ramset™ recommends to always start a new application with the minimum powerload strength, and if applicable, the tool at minimum power setting, then gradually increase power with load strengths, and if applicable, a combination of power adjustment setting powerload and pin length. PIN Part No. SP12 SP12 SC925 SC930C SC930C SC925C SC930 SC930 SC950C SC960C www.ramset.com.au 1300 780 063 41 FrameBoss™ Fully Automatic Tool Powder Actuated Systems Quick change fastener guide Power adjustment Automatic piston return NEMW agazine Cushioned rubber grip 75mm odel M le Availab 10 pin magazine FAST FIXING! 75mm or 100mm single shot fastener guide included in tool kit, dependent on tool model 60mm Magazine Model Description The Ramset™ FrameBossTM is a fully automatic powder actuated tool, which is capable of fixing 10 pins without the need to reload or cycle the tool. The automatic piston return system and 10 pin magazine allow for faster fixing rates with less effort. The magazine can be adjusted to lock into a number of positions to allow the tool to be used in confined spaces. The FrameBossTM tool is also supplied with a single shot fastener guide to allow the tool to be used with longer fasteners and assembles such as brackets and clips. With a huge 380 Joules of impact energy coupled with power adjustment, the tool can be used in a wide variety of applications e.g. Timber framing, formwork and the fixing of steel track. FrameBossTM is designed to save you time and money. Specification Model Weight Impact Force Fixing Capacity: Timber to Concrete Timber to Steel Metal to Concrete Metal to Steel Pin Capacity (Single shot) Pin Capacity (Magazine) Overall Length Substrates FrameBoss 3.0 kg (3.2 kg with mag.) 380J FrameBoss75 3.7 kg (3.99 kg with mag.) 380J 50mm 50mm 3mm 3mm up to 75mm 75mm 50mm 3mm 3mm up to 100mm up to 60mm up to 75mm 490mm 525mm Concrete, Steel, Masonary Concrete, Steel, Masonary Related Products Power Loads Drive Pins 42 Tool Accessories Drive Pin Accessories www.ramset.com.au 1300 780 063 Features & Benefits • Automatic piston return • No manual cycling required • Easy to maintain on site • 10 Pin magazine and single shot fastener guide • 75mm single shot capacity, 100mm with FRAMEBOSS 75 • 60mm magazine capacity, 75mm with FRAMEBOSS 75 • 380J maximum impact energy • Power adjustment • Trigger lock • Hand guard • Cushioned rubber grip FrameBoss™ Fully Automatic Tool Trades & Applications Powder Actuated Systems Residential Home Formwork Ceiling & Partitioning Bricklayer Builder Contractor Contractor Timber to concrete 4 4 Timber to steel 4 4 Sacrificial steel formwork to steel 4 Steel track to concrete & steel 4 4 Brick Ties to concrete & steel 4 4 Standard Operating Procedure Always read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain personal instruction and training from a Ramset™ representative. 1. First cycle the tool and insert the power load strip. 2. Insert the correct fastener or collated fasteners, (without compressing the front of the tool). 3. The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface). 4. Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate. FrameBoss™ Part No FrameBoss FrameBoss75 Description FrameBoss™ tool kit 60 mm Magazine FrameBoss™ tool kit 75 mm Magazine Order Qty 1 1 Kit includes: FrameBoss™ tool, steel tool case, single shot fastener guide, magazine, safety glasses, maintenance kit and instruction manual. FrameBoss Accessories Part No PA37037 010982 010983 PA37040 PA37038 PA9316 PBT PA1613 PA37023 PAWS8 Description Piston Piston Return Spring (x2) Piston Buffer (x2) Fastener Guide Assembly Magazine Assembly PA Lubricating and Release Oil Drive Pin Removal Tool Safety Glasses Spall Shield Explosive Tool in Use - Safety Warning Sign FrameBoss75 Accessories Order Qty 1 1 1 1 1 1 1 1 1 1 Part No PA37041 011483 010983 PA37063 PA37049 PA9316 PBT PA1613 PA37023 PAWS8 Description Piston Piston Return Spring (x1) Piston Buffer (x2) Fastener Guide Assembly Magazine Assembly PA Lubricating and Release Oil Drive Pin Removal Tool Safety Glasses Spall Shield Explosive Tool in Use - Safety Warning Sign Order Qty 1 1 1 1 1 1 1 1 1 1 Power Load Strips Part No PLSGR22 PLSYW22 PLSRD22 Colour Green Yellow Red Strength Weak Medium Strong Order Qty 100 100 100 www.ramset.com.au 1300 780 063 43 FrameBoss™ Collated Drive Pins Standard Collated Drive Pins for Fixing to Concrete and Masonary Powder Actuated Systems Collated Drive Pins designed for use with the FrameBoss™ magazine for fastening to standard strength concrete, masonry and steel up to a maximum of 8mm. Specifications Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Shear Strength Tensile Strength Hardness Carbon Steel (Plastic Collation) Zinc Electroplated (Minimum coating 7µm) 8.8mm 3.7mm 1120N/mm2 1800N/mm2 50 -55HRC Part No Drive Pin Length C925C C930C C940C C950C C960C C975C 25mm 30mm 40mm 50mm 60mm 75mm Max Fixture (thickness to steel) 12mm 18mm 30mm 35mm 45mm 60mm Max Fixture (thickness to concrete) 2mm 5mm 15mm 25mm 35mm 50mm Order Qty 500 500 300 300 300 300 Collated Pins for Fixing to Structural Steel and Hard Concrete The Ramset™ range of Premium Collated Drive Pins is designed for use with the FrameBoss™ magazine for fastening to steel and hard concrete applications. The design of these drive pins allows them to penetrate hard materials with less power while the strengthened shank greatly reduces the possibility of column collapse. Specifications Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Shear Strength Tensile Strength Hardness Carbon Steel (Plastic Collation) Zinc Electroplated (Minimum coating 7µm) 8.8mm 4.0mm / 3.7mm 1240N/mm2 2000N/mm2 54 -58HRC Part No Drive Pin Length SC925C SC930C SC940C SC950C SC960C 25mm 30mm 40mm 50mm 60mm Max Fixture (thickness to steel) 12mm 18mm 30mm 35mm 45mm Max Fixture (thickness to concrete) 2mm 5mm 15mm 25mm 35mm *Refer to page 56 for more fasteners that are suitable for use with the FrameBossTM Tool Ramset™ recommends application test on-site before commencing use. 44 www.ramset.com.au 1300 780 063 Order Qty 500 500 300 300 300 FrameBoss™ InsulFastTM Accessory Kit Description The Ramset™ InsulFast™ adaptor kit transforms the FrameBoss™ tool into a specialist insulation fixing tool with automatic piston return. The FrameBoss™ tool in this configuration is capable of fastening insulation from 40mm to 120mm without compression. (This adaptor is not compatible with the FRAMEBOSS75 model tool) Accessories Part No PA11030 011031 011032 Description InsulFast™ adaptor kit includes Fastener Guide Assembly, Piston and Piston Return Spring Piston - includes Piston Return Spring Piston Return Spring x 2 Fastener Specification Fastener Body Material Holding Diameter Lengths Available Drive Pin Material Drive Pin Plating Drive Pin Shear Strength (Ultimate) Technical Load Data Part No. CI960 CI670 CI6100 CI6120* Concrete Strength 25 – 45 MPa 25 – 45 MPa 25 – 45 MPa 25 – 45 MPa Order Qty 1 1 1 Powder Actuated Systems NEW High Density Polyethylene (HDPE) 60 mm (90 mm for CI960) 50 mm to 120 mm Carbon Steel Electroplated Zinc 12.0 kN Tensile Working Load Limit WLL 0.30 kN 0.30 kN 0.30 kN 0.30 kN The recommended loads (kN) are calculated from the mean ultimate load and a factor of safety higher than 4. A minimum of 4 fixings per fastened unit are required. * Available upon request. Insulation Fasteners for Concrete, Masonary and Steel Part No. CI960 CI670 CI6100 CI6120* Rigid Insulation Thickness 60mm 70mm 100mm 120mm Soft Insulation Thickness 60 mm – 65mm 70 mm – 75mm 100mm – 110mm 120mm – 130mm Fastener Order Colour Qty Black 100 Natural (White) 200 Natural (White) 100 Natural (White) 100 * Available upon request. Ramset™ recommends application test on-site before commencing use. www.ramset.com.au 1300 780 063 45 Rocket Automatic Short Pin Tool Power adjustment Powder Actuated Systems Automatic piston return Cushioned rubber grip Description The Ramset™ Rocket is the fastest high volume, short pin tool. This powerful fully automatic tool performs high volume repetitive short pin fixings with ease. Specifications Weight Impact Force Fixing Capacity: Timber to Concrete Timber to Steel Metal to Concrete Metal to Steel Pin Capacity Overall Length Substrates 2.2kg 360J 25mm 35mm 3mm 3mm up to 50mm 435mm Concrete, Steel, Masonary Features & Benefits • Fast - 10 shot strip feed with automatic advance • Optimum fixing - power adjustment ensures consistent performance • Power - adjustable for use with steel or concrete • Lightweight - minimal operator fatigue • Minimal maintenance Related Products Power Loads Drive Pins Tool Accessories Drive Pin Accessories 46 www.ramset.com.au *Refer to page 56 for fasteners that are suitable for use with the Rocket Tool 1300 780 063 Rocket Automatic Short Pin Tool Trades & Applications Residential Home Ceiling & Partitioning Builder Contractor Steel framing to concrete 4 Steel track to concrete & steel 4 Brick Ties to concrete & steel Bricklayer 4 Powder Actuated Systems Standard Operating Procedure Always read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain personal instruction and training from a Ramset™ representative. 1. First insert the power load strip. 2. Insert the correct fastener, (without compressing the front of the tool). 3. The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface). 4. Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate. Rocket Part No ROCKET Description Rocket Tool Order Qty 1 Kit includes: Rocket tool, high impact carry case, safety glasses, maintenance kit and instruction manual. Rocket Accessories Part No A1010 A1049A A1130A PA9316 PBT PA1613 PAWS8 Description Piston Fastener Guide Assembly Buffer Assembly PA Lubricating and Release Oil Drive Pin Removal Tool Safety Glasses Explosive Tool in Use - Safety Warning Sign Order Qty 1 1 1 1 1 1 1 Power Load Strips Part No PLSGR22 PLSYW22 PLSRD22 Colour Green Yellow Red Strength Weak Medium Strong Order Qty 100 100 100 www.ramset.com.au 1300 780 063 47 FrameMaster™ TS750P - Power Adjustable Tool Powder Actuated Systems Power adjustment Cushioned rubber grip Description The Ramset™ FrameMaster™ TS750P is the timber framing expert. A power adjustable tool designed for fixing timber framing to concrete and general repetitive work. Specifications Weight Impact Force Fixing Capacity: Timber to Concrete Timber to Steel Metal to Concrete Metal to Steel Pin Capacity Overall Length Substrates 2.5kg 300J 60mm 50mm 3mm 3mm up to 85mm 380mm Concrete, Steel, Masonary Features & Benefits • Fast – 10 shot strip feed with automatic advance • Optimum fixing – positive power adjustment ensures consistent performance • Power – adjustable for use with steel or concrete • Minimal maintenance – easy to dismantle & clean to reduce downtime • Long Life – long life piston & buffer Related Products Power Loads Drive Pins Tool Accessories Drive Pin Accessories 48 www.ramset.com.au *Refer to page 56 for fasteners that are suitable for use with the FrameMasterTM TS750P Tool 1300 780 063 FrameMaster™ TS750P - Power Adjustable Tool Trades & Applications Residential Home Formwork Bricklayer Builder Contractor 4 4 4 4 4 4 Timber to concrete Timber to steel Brick Ties to concrete & steel Powder Actuated Systems Standard Operating Procedure Always read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain personal instruction and training from a Ramset™ representative. 1. First cycle the tool and insert the power load strip. 2. Insert the correct fastener, (without compressing the front of the tool). 3. The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface). 4. Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate. FrameMaster™ TS750P Part No TS750P Description FrameMaster™ TS750P tool Order Qty 1 Kit includes: FrameMaster™ tool, high impact carry case, safety glasses, maintenance kit and instruction manual. FrameMaster™ TS750P Accessories Part No PA27833 PA27432 PA27831 PA9316 PBT PA1613 PA27580 PAWS8 Description Piston Assembly - Standard Piston Assembly - High Power Fastener Guide Assembly PA Lubricating and Release Oil Drive Pin Removal Tool Safety Glasses Spall Shield Explosive Tool in Use - Safety Warning Sign Order Qty 1 1 1 1 1 1 1 1 Power Load Strips Part No PLSGR22 PLSYW22 PLSRD22 Colour Green Yellow Red Strength Weak Medium Strong Order Qty 100 100 100 www.ramset.com.au 1300 780 063 49 FormMaster™ The Formworker’s Tool Powder Actuated Systems Power adjustment Cushioned rubber grip HIGH POWER! Description The Ramset™ FormMaster™ is the professional’s choice for long pin fixing. A high powered fastening system with the power and comfort to meet the demands of the timber and steel formwork industry and heavier repetitive fixing jobs. Specifications Weight Impact Force Fixing Capacity: Timber to Concrete Timber to Steel Metal to Concrete Metal to Steel Pin Capacity Overall Length Substrates 3.0kg 400J 75mm 50mm 3mm 3mm up to 100mm 448mm Concrete, Steel, Masonary Features & Benefits • Fast – 10 shot strip feed with automatic advance • Optimum fixing – positive power adjustment ensures consistent performance • Power – adjustable for use with steel or concrete • Front barrel safety grip & hand guard – all day use comfort • Minimal maintenance – easy to dismantle & clean to reduce downtime • Long Life – long life piston & buffer Related Products Power Loads Drive Pins Tool Accessories Drive Pin Accessories 50 www.ramset.com.au *Refer to page 56 for fasteners that are suitable for use with the FormMasterTM Tool 1300 780 063 FormMaster™ The Formworker’s Tool Trades & Applications Standard Operating Procedure Powder Actuated Systems Residential Home Formwork Bricklayer Builder Contractor Timber to concrete 4 4 Timber to steel 4 4 Brick Ties to concrete & steel 4 4 Sacrificial steel formwork to steel 4 Always read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain personal instruction and training from a Ramset™ representative. 1. First cycle the tool and insert the power load strip. 2. Insert the correct fastener, (without compressing the front of the tool). 3. The tool should then be compressed against the work surface. (Making sure that the tool is perpendicular to the work surface). 4. Once the tool is compressed the trigger is actuated and the fastener is driven through the material being fastened into the substrate. FormMaster™ Part No Description FORMMASTER FormMaster™ Tool Order Qty 1 Kit includes: FormMaster™ tool, high impact carry case, safety glasses, maintenance kit and instruction manual. FormMaster™ Accessories Part No PA28811 PA312860 PA28816 PA9316 PBT PA1613 PA310000 PAWS8 Description Piston Assembly Buffer x 5 Fastener Guide Assembly PA Lubricating and Release Oil Drive Pin Removal Tool Safety Glasses Spall Shield Explosive Tool in Use - Safety Warning Sign Order Qty 1 1 1 1 1 1 1 1 Power Load Strips Part No PLSGR22 PLSYW22 PLSRD22 Colour Green Yellow Red Strength Weak Medium Strong Order Qty 100 100 100 www.ramset.com.au 1300 780 063 51 TyMaster™ The Overhead Tool Powder Actuated Systems Automatic piston return Dedicated pole tool Automatic charge advance OVERHEAD FIXING! Description The Ramset™ TyMaster™ is an effortless, overhead fixing, fully automatic tool with extension pole for efficient, remote, overhead fixing of suspended ceilings and services installations. Typical Properties Weight Impact Force Fixing Capacity: Metal to Concrete Metal to Steel Pin Capacity Overall Length (including pole) Substrates 2.3kg 320J 3mm 3mm up to 32mm 2000mm Concrete, Steel, Masonary Features & Benefits • Fast 10 shot strip feed with automatic advance • Lightweight – reduced fatigue in overhead operation • Fully automatic – high install rate • Safe – patented “Breech lockout” prevents the tool from firing while directed horizontally or while directed below the horizontal • Minimal maintenance Related Products Power Loads Drive Pins Tool Accessories Drive Pin Accessories 52 www.ramset.com.au *Refer to page 56 for fasteners that are suitable for use with the TyMasterTM Tool 1300 780 063 TyMaster™ The Overhead Tool Trades & Applications Ceiling & Partitioning Contractor Fixing of suspended ceilings 4 Light duty cable tray Catenary wire fixings Electrical Contractor 4 4 Powder Actuated Systems Standard Operating Procedure Always read and understand the instruction manual before attempting to operate a Ramset™ powder actuated tool. Ramset™ also recommends users obtain personal instruction and training from a Ramset™ representative. 1. First insert the power load strip in the tool. 2. Load the correct drive pin, (without compressing the front of the tool). 3. Carefully raise the tool to the ceiling and depress the barrel assembly where the fastening is to be made. 4. While holding the tool perpendicular and compressed against the work surface, forcibly push upwards on the pole handle to fire the tool. TyMaster™ Part No TYMASTER Description TyMaster™ Tool Order Qty 1 Kit includes: TyMaster™ tool, high impact carry case, 1560mm (3 x 520mm) pole extension, safety glasses, maintenance kit and instruction manual. TyMaster™ Accessories Part No 653116 PAT1085 653021 653106 653035 PA9316 PBT PA1613 PAWS8 Description Piston Standard Piston High Power Buffer x 3 Fastener Guide Assembly Spall Shield PA Lubricating and Release Oil Drive Pin Removal Tool Safety Glasses Explosive Tool in Use - Safety Warning Sign Order Qty 1 1 1 1 1 1 1 1 1 Power Load Strips Part No PLSGR22 PLSYW22 PLSRD22 Colour Green Yellow Red Strength Weak Medium Strong Order Qty 100 100 100 www.ramset.com.au 1300 780 063 53 Drive Pins Powder Actuated Systems Standard Drive Pins for Concrete, Masonry and Steel Powder Actuated Systems Drive Pins designed for fastening to standard strength concrete, masonry and steel up to a maximum of 8mm. Specifications Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Shear Strength Tensile Strength Hardness Carbon Steel Zinc Mechanically Plated (Min coating 6µm) 7.8mm 3.7mm 1200N/mm2 1950N/mm2 52 - 55HRC Part No Drive Pin Length LDU25 LDU32 LDU38 LDU42 LDU50 LDU57 LDU65 LDU75 LDU90 LDU99 25mm 32mm 38mm 42mm 50mm 57mm 65mm 75mm 90mm 100mm Max Fixture (thickness to steel) 12mm 20mm 25mm 30mm 35mm 45mm 50mm N/A N/A N/A Max Fixture (thickness to concrete) 2mm* 7mm 12mm 20mm 25mm 35mm 45mm 50mm 65mm 75mm Order Qty 100 100 100 100 100 100 100 100 100 100 * Denotes steel fixture only Timber Formwork Pins for Concrete and Easy Pin Removal Drive Pins designed for fastening timber formwork to concrete. When the timber needs to be removed, the small head reduces the force required to strip the timber. The groove in the shank allows the pin to be removed easily with Ramset’s drive pin breaker tool. Specifications Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Shear Strength Tensile Strength Hardness PBT (Pin Breaker Tool) Carbon Steel Zinc Mechanically Plated (Min coating 6µm) 6.3mm 3.7mm 1200N/mm2 1950N/mm2 52 - 55HRC Part No LDU60F LDU75F LDU99F PBT (Pin Breaker Tool) Drive Pin Length 60mm 75mm 100mm Max Timber Thickness 35mm 50mm 75mm Ramset™ recommends application test on-site before commencing use. 56 www.ramset.com.au 1300 780 063 Order Qty 200 200 200 1 Drive Pins Powder Actuated Systems Premium Drive Pins for Structural Steel Ramset’s range of Premium Drive Pins has been designed for steel and hard concrete applications. The design of these drive pins allows them to penetrate hard materials with less power while the strengthened shank greatly reduces the possibility of column collapse. Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Shear Strength Tensile Strength Hardness Carbon Steel Zinc Electroplated (Min coating 7µm) 8.8mm 4.0 / 3.5mm 1240N/mm2 2000N/mm2 54 - 58HRC Part No Description SC925 SC930 SC940 SC950 SC950W SC960 SC960W SC970 Thin Steel to Structural Steel Pin Timber to Structural Steel Pin Timber to Structural Steel Pin Timber to Structural Steel Pin Frame & Truss 16mm Washered Pin Timber to Structural Steel Pin Frame & Truss 16mm Washered Pin Timber to Structural Steel Pin Max Fixture (thickness to steel) 12mm 18mm 30mm 35mm 35mm 45mm 45mm 55mm Max Fixture (thickness to concrete) 2mm 5mm 15mm 25mm 25mm 35mm 35mm 45mm Order Qty 100 100 100 100 100 100 100 100 Powder Actuated Systems Specifications Washered Drive Pins For Concrete, Masonry and Steel Washered Drive Pins designed to provide maximum clamping load while improving tool piston life. Wherever possible the use of washered drive pins is recommended to prevent failure of the material being fastened. LWU25K Specifications Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Shear Strength Tensile Strength Hardness Carbon Steel Zinc Mechanically Plated (Min coating 6µm) 7.8mm 3.7mm 1200N/mm2 1950N/mm2 52 - 55HRC LWU25 Part No Washer Diameter Drive Pin Length LWU25 LWU32 LWU75 LWU25K 22mm 22mm 16mm 16mm 25mm 32mm 75mm 25mm Max Fixture (thickness to concrete) 2mm* 7mm 50mm 2mm* Order Qty 100 100 100 100 * Denotes steel fixture only Ramset™ recommends application test on-site before commencing use. www.ramset.com.au 1300 780 063 57 Drive Pins Powder Actuated Systems Angle Bracket and Threaded Rod Hanger Assemblies LAU25 Powder Actuated Systems Ramset’s Angle Bracket and Threaded Rod Hanger Assemblies provide a secure fixing point for a wide variety of applications. Specifications Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Part No LAU25 LAU30H LZU30H LZU30H Carbon Steel Zinc Plated 7.8mm Various Description Standard Duty Heavy Duty Threaded Rod Hanger - M10 Drive Pin Length 25mm 25mm 25mm Order Qty 100 100 100 Drive Pins For Fixing Thin Steel To Steel Drive pin for fixing thin steel to structural steel sections. Specifications Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Shear Strength Tensile Strength Hardness Carbon Steel Zinc Mechanically Plated (Min coating 6µm) 7.8mm 4.0mm 1200N/mm2 1950N/mm2 52 - 55HRC Part No SP12 Description Premium Steel Pin Drive Pin Length 13mm Order Qty 100 Washered Drive Pins For Fixing Thin Steel To Steel Drive Pin designed for fixing thin steel to structural steel sections. This drive pin provides excellent clamping with a special 14mm diameter washer that interacts with a tapered section on the shank of the drive pin. Specifications Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Shear Strength Tensile Strength Hardness Part No SBR9 Carbon Steel Zinc Electroplated (Min coating 7µm) 8.8mm 4.0mm 1240N/mm2 2000N/mm2 54 - 58HRC Description Decking Pin Washer Diameter 14mm Drive Pin Length 20mm * Suitable for use with Kingflor®, Bondek®, Condeck® Ramset™ recommends application test on-site before commencing use. 58 www.ramset.com.au 1300 780 063 Order Qty 100 Drive Pins Powder Actuated Systems Soft Washered Membrane Fastener Soft Washered Drive Pin designed for fastening insulation up to 25mm, also designed for fastening foils and membranes such as drainage sheeting to concrete. The soft washer prevents any damage to the foil or membrane. Specifications Powder Actuated Systems Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Shear Strength Tensile Strength Hardness Washer Diameter Carbon Steel (Plastic Washer) Zinc Electroplated (Min coating 7µm) 8.8mm 3.7mm 1120N/mm2 1800N/mm2 50 - 55HRC 35mm Part No Drive Pin Length CR950P 50mm Max Insulation Thickness 25mm Order Qty 200 Drive Pin Accessories Drive Pin accessories for use with Ramset’s standard LDU range of Standard Drive Pins for concrete, masonry and steel. The use of the discs provides maximum clamping loads while improving tool piston life. The use of the angle clip provides a fixing point for applications such as catenary wire. Specifications Raw Material Corrosion Protection Low Carbon Steel Zinc Electroplated (Min coating 6µm) RCD16F Part No RCA25F RCD16F RCD22F Description 25mm Angle Clip 16mm Disc 22mm Disc RCD22F RCA25F Order Qty 100 100 100 Ramset™ recommends application test on-site before commencing use. www.ramset.com.au 1300 780 063 59 Misc. Drive Pins Powder Actuated Systems Collated Drive Pins to suit Hilti™, DX 351, DX 460, DX A40, DX A41 Magazine Tools Powder Actuated Systems Collated Drive Pins designed for use with Hilti tools; DX460, DX351, DX-A40/41 fitted with a magazine. Specifications Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Shear Strength Tensile Strength Hardness Part No RHC22 RHC27 ­RHC52 RHC62 RHC72 Carbon Steel Zinc Mechanically Plated (Min coating 7µm) 8.2mm 3.7mm 1200N/mm2 1950N/mm2 52 - 55HRC Nominal Head Diameter 8.2mm 8.2mm 8.2mm 8.2mm 8.2mm Length 22mm 27mm 52mm 62mm 72mm Max Fixture (Thickness to steel) 10mm 14mm 37mm 47mm 62mm Max Fixture (Thickness to Concrete) 1mm 3mm 27mm 42mm 47mm Order Qty 100 100 100 100 100 Drive Pins to suit Previous Ramset™ Tools J20S, J20, 1/4” Barrel Drive Pins for use with previous Ramset™ direct acting powder actuated tools; J20, J20S fitted with a ¼” barrel. Specifications Raw Material Corrosion Protection Nominal Head Diameter Nominal Shank Diameter Shear Strength Tensile Strength Hardness Carbon Steel Zinc Mechanically Plated (Min coating 6µm) 6.3mm 3.7mm 1200N/mm2 1950N/mm2 52 - 55HRC Part No HDB50 HDB64 HDB75 HDB95 Nominal Head Diameter 6.3mm 6.3mm 6.3mm 6.3mm Length 50mm 64mm 75mm 95mm Ramset™ recommends application test on-site before commencing use. 60 www.ramset.com.au 1300 780 063 Order Qty 100 100 100 100 Power Loads Powder Actuated Systems Powerloads to suit Previous Ramset™ Tools - J20S, J20, 1/4” Barrel Power Load Cartridge designed for use with Ramset’s JobMaster™ tool and previous Ramset™ direct acting powder actuated tools; J20, J20S. Charge Type Calibre Part No PLCGR22S PLCYW22S PLCRD22S *PLCPU22S Single Cartridge 5.6 x 16mm Calibre 5.6mm x 16mm 5.6mm x 16mm 5.6mm x 16mm 5.6mm x 16mm Colour Green Yellow Red Purple Strength Weak Medium Strong Very Strong Order Qty 100 100 100 100 * Not suitable for use with JobMaster™ Strip Powerloads to suit Previous Ramset™ Strip Feed Tools & Hilti™ Strip Feed Tools Powder Actuated Systems Specifications Power Load Strip designed for use with Ramset™ tools; FrameBoss™, FormMaster™, TyMaster™, FixMaster™ (TS60P), FrameMaster™ (TS750(P)), S75A, FrameFix™, Striker, Rocket. Also suitable for use with Hilti tools; DX460, DX351, DX-A40/41, DX36. Specifications Charge Type Calibre Part No PLSGR22 PLSYW22 PLSRD22 10 Shot Strip 6.8 x 11mm Calibre 6.8mm x 11mm 6.8mm x 11mm 6.8mm x 11mm Colour Green  Yellow  Red   Strength Weak Medium Strong www.ramset.com.au Order Qty 100 100 100 1300 780 063 61