Featherweight 75 Instruction Book Operating Manual, Same As Singer 4166 Except Accessories

Transcript

MAIN PARTS 7 8 9 10 11 12 13 1 2 14 3 01 02 03 04 05 06 07 08 09 10 11 17 4 15 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 16 56 57 58 59 60 61 62 63 64 65 66 5 6 1.Face Plate 2.Reverse Stitch Button 3.Slow Button 4.Start/Stop Button 5.Speed Control Lever 6.Extension Table (Accessory Case) 7.Bobbin Winder Tension disc 8.Needle Up/Down Button 9.Thread Tension Regulator 10.Spool pin 11.Bobbin winder Shaft 12.Bobbin Winder Stop 13.Hand Wheel 14.Stitch Width Button 15.Stitch Length Button 16.Pattern Selector Button 17.Thread Cutter -2- 19 18 25 20 24 21 23 22 18.Carrying Handle 19.Thread guide for upper threading 20.Power switch 21.Air vent 22.Foot control plug 40 23.Plug socket 26 24.Power cord 25.Foot control 27 26.Lower thread guide 27.Needle threader lever 28 28.Needle threader 29 29.Buttonhole lever 30.Presser foot thumb screw 31.Needle plate 30 32.Bobbin cover 33.Bobbin cover release lever 31 34.Presser foot holder 35.Presser foot 32 36.Needle thread guide 37.Needle clamp screw 38.Presser foot lever 39.Drop feed lever 40.LED light 38 37 36 35 34 33 39 -3- ACCESSORIES Some accessories are provided in the accessory case. 1.Needle set 2.Bobbins 3.Spool pin cap (large) 4.Spool pin cap (small) 5.Straight stitch foot 6.Needle plate screwdriver 7.Screwdriver 8.Buttonhole opener with brush 9.Oiler 10.Buttonhole Foot 11.Overcasting Foot 12.Zipper Foot 13.Blind hem Foot 14.Satin Foot 15.Rolled hem Foot 16.Gathering Foot 17.Darning & Embroidery Foot 18.General purpose foot(on machine) 19.Extension table 2 1 3 4 7 6 5 8 11 13 12 10 9 14 18 15 19 OPENING THE ACCESSORY CASE To open the accessory case, lift up on the top left side of the table and pull toward you. -4- 16 17 a.REMOVING THE EXTENSION TABLE Hook your finger to the bottom of extension table and slid to the left. To attach, insert to the right. b.OPENING THE ACCESSORY CASE Hook your finger to the left side of accessory case and pull toward you. DUST COVER Cover the machine with dust cover when it is not in use. This manual will be stored on the holder provided on the side of the cover. -5- CHANGING THE PRESSER FOOT The presser foot must be changed according to the stitch you sew, or work you do. ! CAUTION:To prevent accidents. Turn off the power switch before you change the presser foot. 1.Turn the hand wheel toward you until the needle is at its highest point. 2.Raise the presser foot lifter. 3.Remove the presser foot by pushing the presser foot release lever toward you. 4.Place desired foot with its pin directly under the slot in presser foot holder. 5.Lower the presser foot lifter and the presser foot will snap into place. 2 5 3 REMOVING THE PRESSER FOOT HOLDER 1 You may need to remove the presser foot holder to use some presser feet. To remove, raise the presser foot lifter and loosen the presser foot thumb screw (A). To attach, tighten the screw after raising the presser foot holder. A 4 INSERTING THE NEEDLE Select a needle of the right type and size for the fabric to be sewn. ! CAUTION:To prevent accidents. 2 Turn off the power before removing the needle. 1.Turn the hand wheel toward you until the needle is at its highest point. 2.Loosen the needle clamp screw. 3.Remove the needle. 4.Insert new needle into needle clamp with the flat side to the back and push it up as far as it will go. 5.Tighten the needle clamp screw. 1 5 3 A.Do not use bent or blunt needles. Place needle on a flat surface and check to see if bent. 4 A -6- CONNECTING THE MACHINE 1 2 -7- FOOT CONTROLLER For this machine use foot controller type YSD 180034. C A B -9- BOBBIN WINDING REMOVING THE BOBBIN 1 2 1.Remove the slide cover by sliding the locker to right and push down the left corner of slide cover. At the same time. 2.Remove the bobbin from the machine. WINDING THE BOBBIN 1 2 4 3 5 1.Pivot spool pin into highest horizontal spool pin position. 2.Pass a spool of thread on the spool pin. Secure to place a spool of thread on the pin. Secure it with the spool cap to ensure smooth flow of thread. 3.Pass thread from spool through thread guides as shown. 4.Pull end of thread through hole in bobbin as shown. 5.Make sure the bobbin winder shaft is in left position. Place bobbin onto shaft with end of thread coming from top of bobbin. Push bobbin winder shaft to right until it clicks. Hold onto end of thread. 6.Start machine. The thread that is held will snap or may be trimmed with a scissors. Bobbin will cease turning when completely filled. Push shaft to left to remove bobbin. -11- INSERTING THE BOBBIN 1. Place bobbin into bobbin holder with the 1 thread unwinding counter clockwise. 2. Draw thread into notch (A). 2 A 3. Pull thread toward the left and along the inside of spring (B) until it slips into notch (C) being sure that thread does not slip out of notch (A). 3 C B A C B 4. Pull thread out about 10 inches and replace the slide cover. 4 -12-