Transcript
Echo® PowerWake™ Instructions VIBRATING AND SOUNDING ALARM CLOCK
Product Code: 474-1005-01 Hearing Products International Limited
Page 1
IMPORTANT When using this unit, basic safety precautions as below should always be followed to avoid the risk of electric shock or personal injury. Do not use in an environment that is damp, wet, very hot or very cold. To clean the clock and its accessories, use only a soft cloth and an inorganic cleaner. Install the unit securely on a stable surface and install the unit where the power cord will not be subject to damage or cause a tripping hazard. The unit may get warm when being used; ensure the unit has adequate ventilation. Only use the Hearing Products approved mains adapter. Do not use any other type of mains adapter.
Battery Backup PLEASE NOTE....that the alarm can only be used when the mains power adapter is plugged in and power is switched on. If power is removed from the clock the clock will keep its time for up to 72 hours – in case of a power cut.
Page 2
PowerWake™ top panel:
1. TIME
Page 3
2. ALARM
3. SNOOZE 4. HOUR 5. MIN.
PowerWake™ back panel :
6. ALARM ON/OFF
7. DIMMER HI / LO
9. SOUND HI/LO/OFF
10. TONE HI/MED/LO
12. 12V DC JACK
13. SIDE LIGHT ON/OFF
Page 4
8. BED SHAKER JACK 11. 12/ 24 HR CLOCK
CONTENTS 1 x Alarm Clock 1 x Bed Shaker 1 x Mains power adapter 12V DC 2A Positive Centre
Set up Procedure 1. Plug the mains power adapter into the wall socket and plug the jack plug at the end of the power lead into 12V DC socket (12) on the back of the PowerWake™. 2. Plug the bed shaker into the socket (8) on the back of the PowerWake™ and place the bed shaker under the pillow.
Set Time - When the clock is first plugged in, you will need to set the time. If the clock is set for 12 hour mode and you wish to set the time to PM, the clock PM indicator should be lit (top left on display). When it is off, it indicates 'AM'. Unless using the 24 hour clock. To alter between 12 and 24 hour display you will need to flick the switch which is located on the back of the clock (11). When the alarm indicator is on, the alarm will sound at the set time.
Page 5
Set Time Select 12 / 24 hour mode on the back of the clock (11). 1. Press the time button (1) and the hour button (4) at the same time until the correct hour time is displayed. 2. Release the hour and press the Minute button (5) still pressing the time button, until the correct minute time is displayed. Note: You can press the Hour and Min button once or press and hold to reach the desired time, faster. 3. If you are in 12 hour mode, ensure you set correctly for AM (indicator will not be lit) or PM (indicator will be lit).
To Set the Alarm 1. Press and hold the Alarm button (2) and the hour button (4) at the same time until required Alarm hour is displayed. 2. Release the hour button and press the Minute button (5) still pressing the Alarm button, until the correct Alarm minute is displayed. Note: You can press the Hour and Min button once or press and hold to reach the desired time faster. 3. Be sure to select AM/PM correctly, unless using the 24 hour clock.
Page 6
To Operate the Alarm Slide the Alarm On/Off switch (6) to On Position. The alarm will then sound at the set time. Snooze When the snooze button (3) is depressed, the snooze button gives approx. 9 minute snooze. Hi-Low Dimmer Switch If more intense display is preferred, press the dimmer button (7) on the back of the clock to the 'HI' position. If less intense display is desired, press the dimmer (7) button on the back of the clock to the ‘LO’ position. Options Vibrate Only/ Sound Only/ Flash Only/ Vibration & Sound/ Flash & Sound/ Vibrate & Flash.
To stop vibrate simply remove bed shaker from bed shaker jack (8). All other options select on/off on back panel.
(9) AUDIO SOUND SWITCH: Can choose the alarm sound loudness HIGH or LO or OFF. (10) AUDIO TONE SWITCH: Can choose the alarm tone to HIGH (1500 Hz) or MEDIUM (1000 Hz) or LO (520 Hz). (13) SIDE LIGHT SWITCH: this switch can turn on or off the side light.
Page 7
Replacement Parts P/N
Qty
Description
4720
1
PowerWake™ Clock
471
1
Bed Shaker
570-1010-01
1
UK Power Adapter
570-1011-01
1
PowerWake™ box/ instructions
Technical Specifications Power Supply
12V DC 2A Positive Centre
Snooze Time
Approximately 9 minutes
Dimensions
0.75KGS
Weight Bed Shaker Voltage
Page 8
22.5x9x9cm 9V
Hearing Products International Limited Echo House, 26 / 27 Haigh Park, Stockport, SK4 1QR, England Tel. +44 (0) 161 480 8003 Fax +44 (0) 161 480 8006 www.hear4you.com
Hearing Products International Limited declares that the Echo® PowerWake™ complies with all relevant EU directives. The full EU declaration of conformance for the Echo® Powerwake™ is available from Hearing Products International Ltd.
Hearing Products International Ltd. reserve sole right to alter prices, design and/ or technical specifications or colours without prior notice. Echo® PowerWake™ Instructions ©Copyright Hearing Products International Limited. E&OE 09/16. Version 1.
Page 9
