Transcript
88Y6057-A
SFP+, 10GBASE-SR 10G Ethernet Module 850mn, 300m, MMF, LC RoHS6
88Y6057-A
10Gbase SFP+ Transceiver
Features
• • • • • • • • •
Compliant to SFP+ Electrical MSA SFF-8431 Compliant to SFP+ Mechanical MSA SFF-8432 Multi-rate compliance for Ethernet and Fiber Channel Transmission distance up to 300m (OM3 fiber) Sub watt power consumption: 0.65W (typ.) 0°C to +70°C case operating temperature range Laser Class 1 IEC / CDRH compliant RoHS 6/6 compliant Compliant with product safety standards
Product Description The 88Y6057-A is a multipurpose multi-rate optical transceiver module for transmission at 850nm over multimode fiber. Supporting Ethernet and Fiber Channel standards make it ideally suited for 10G data communication and storage area network applications. Its sub watt power consumption and its excellent EMI performance allow system design with high port density. The small form factor integrates an 850nm vertical cavity surface emitting laser (VCSEL) in an LC package and a PIN receiver. Approved Networks Computer Peripheral’s module is lead free, RoHS compliant and is designed and tested in accordance with industry safety standards.
Functional Description The Transceivers convert information from electrical to optical format, and back again, at different data rates depending upon the chosen standard. The transmit path consists of an AC coupled 100 ohm differentially terminated driver coupled to a highly reliable 850nm VCSEL. The laser output may be disabled by pulling the TX_DISABLE line high. The laser is also disabled if this line is left floating, as it is pulled high inside the transceiver. The SFP+ MSA (Multiple Source Agreement) defines two RATE_SELECT lines, one for the transmitter (pin 9) and one for the receiver (pin 7). Depending upon the transceiver application, the transmitter RATE_SELECT line can switch between1 GBd and 10 GBd. The receiver path consists of a ROSA (receiver optical sub-assembly) for optical electrical conversion, followed by a limiting amplifier to boost the electrical signal. A LOSS_OF_SIGNAL (LOS) status line is provided to facilitate easy link detection. Depending upon the transceiver application, optimum receiver bandwidth may be configured using the receiver RATE_SELECT pin: for Ethernet applications to switch between 1 GBd and 10 GBd data rates, and for Fiber Channel applications switch ≤/> 4 GBd data rates.
Approved Networks, Inc.
www.ApprovedOptics.com
Page 1 of 8
88Y6057-A
SFP+, 10GBASE-SR 10G Ethernet Module 850mn, 300m, MMF, LC RoHS6
Electrical Characteristics Absolute Maximum Ratings Rating
Conditions
Symbol
Min
Max
Units
Storage Ambient Temperature Range
Jstg
-40
+85
°C
Powered Case Temperature Range
Jc
0
+75
°C
RH
0
95
%
-0.5
3.6
V
4.0
V
Operating Relative Humidity
Non condensing
Supply Voltage Range @ 3.3V
VCC3
Open Drain VCC Level
VOD
HBM human body model per JEDEC 1 JESD22-A114-B Static Discharge Voltage excluding HBM human body 2 High Speed Pins model EN61000-4-2 Criterion B: Air Static Discharge Voltage Module on 15 Discharge Direct SFP+ 8 Contact discharge Any stress beyond the maximum ratings may result in permanent damage to the device. Specifications are guaranteed only under recommended operating conditions.
Static Discharge Voltage Speed Pins on High
Approved Networks, Inc.
www.ApprovedOptics.com
Page 2 of 8
kV kV
kV
88Y6057-A SFP+, 10GBASE-SR 10G Ethernet Module 850mn, 300m, MMF, LC RoHS6
Recommended Operating Conditions
Parameter
Conditions
Symbol
Min.
Operating Case Temperature
altitude of < 3km
JCase
0
Typical
Power Supply
[email protected]
Vcc3
3.135
DC Common Mode Voltage
Vcm
0
3.30
Max.
Unit
+70
°C
3.465
V
3.6
V
Low Speed Characteristics Parameter
Conditions
Supply Current Transmitter
Supply Current Receiver
Power Consumption
@ VCCTX @ VCCRX
TX_Fault, RX_LOS
TX_Dis, RS0, RS1
Host Vcc Range 2V – 3.47V
Symb ol IVCCT X IVCC RX VOL
Low Voltage TTL
SCL, SDA
Host Vcc Range 3.14V – 3.47V
VIH VIL
Typ
Max
Unit s
120
0.65
mA
1 0.4 Host_ Vcc +0.3
0.8 VccT +0.3
-0.3
mA
125
0 Host_ Vcc – 0.5
VIL
VOH
Min
W V
2.0
-0.3
VccT*0.3
VIH
VccT*0.7
VccT +0.5
VOL
0.0
0.4
VOH
Host_ Vcc – 0.5
Host_ Vcc +0.3
SFI Module Transmitter Input Characteristics Parameter Supported Data Rate Reference Differential Input Impedance Input AC Common Mode Input Voltage
Approved Networks, Inc.
Conditions
Symbol
Min
www.ApprovedOptics.com
Typ
Max
10.3125
11.3
100
Page 3 of 8
Units Gbd
Ω mV (RMS)
88Y6057-A SFP+, 10GBASE-SR 10G Ethernet Module 850mn, 300m, MMF, LC RoHS6
Differential Input Voltage Swing
0.01 –
Differential Input Sparameter
Differential to Common Mode Conversion 2) Total Jitter
Data Dependant Jitter Uncorrelated Jitter
VID
3.9GHz
3.9 –
Eye Mask
11.1GHz
SDD11
150
1)
-10
1)
TJ
DDJ
11.1Ghz
See SFP+ MSA
900
SCD11
0.01 –
mV dB dB
-10
dB
0.28
UI(p-p)
0.1
UI(p-p)
UJ
0.023
RMS
X1
0.14
UI
0.35
UI
X2
SFI Module Receiver Output Characteristics Parameter
Conditions
Symbol
Reference Differential Output Impedance
Termination Mismatch
Supported Data Rate
Output AC Common Mode Output Voltage Differential Output Amplitude RLoad=100Ohm , Differential
Typ
Max
1
10.312 5
11.3
Zd
Δ Zd
Min
100
VOSPP
350
650
Ω 5
%
15
mV (RMS)
800
mV
35
ps
-10
dB
1)
dB
-7
dB
6.5 – 11.1Ghz -3 1) Return Loss given by equation Sxx22(dB) = -8+13.33 Log10(f/5.5), with f in GHz; 2) Common mode reference impedance is 25Ω. Common mode return loss helps absorb
dB
Output Rise and Fall time Differential Input Sparameter Common Mode Output Return Loss2)
20% to 80% 0.01 – 3.9GHz
tRH, tFH
3.9 – 11.1GHz 0.01 – 6.5Ghz
SDD22 SCC22
24
reflection and noise improving EMI.
Gbd
Units
Approved Networks, Inc.
www.ApprovedOptics.com
Page 4 of 8
88Y6057-A SFP+, 10GBASE-SR 10G Ethernet Module 850mn, 300m, MMF, LC RoHS6
Optical Characteristics General Parameters
Parameter
Operating Range
Bandwidth Min Modal (MHz*km)
Conditions 62.5 µm MMF 50 µm MMF 62.5 µm MMF 50 µm MMF 50 µm MMF
160 400 200 500 2000
Optical Transmitter Parameter Optical Transmitter Nominal Wavelength
Conditions
Ethernet version
Fiber Channel version
Average Launch Power
Ethernet version
Extinction Ratio
Typical 1GBd
lOP
2 2 0.5 0.5 0.5
220 500 275 550 X
Fiber Channel version
Average Launch Power
Min
Spectral Width
Symbol
Typ
Max
λΤΡΠ
840
850
860
Pavg
POMA ER
Ethernet 1.25GBd Relative Intensity Noise
Min
RIN
0.65
m
Units
nm
0.45
-7.3
-5.2
-4.3 3.5
tbd
Units
26 66 33 82 300
Symbol
Δλ
Typical 10GBd
-1
dBm
dB
-128
dB/Hz
Optical Receiver Parameter Maximum Input Power
Conditions
Symbol
Center Wavelength
Receiver Sensitivity Ethernet Receiver Sensitivity Fiber Channel
Pavg, PRBS 2 -1, BER < 1*10-12@ 1.25GBd *) OMA, PRBS 231-1, BER < 1*
[email protected] OMA, PRBS 231-1, BER < 1*10-12@2GBd OMA, PRBS 231-1, BER < 1*10-12@4GBd OMA, PRBS 231-1, BER < 1*10-12@8GBd
Approved Networks, Inc.
840
PIN
850
-1
Units
860
-13.0
-12.0
tbd
-11.1
-11.2
www.ApprovedOptics.com
Page 5 of 8
dBm nm
PIN
Max
Typ
λΧ 31
PMAX
Min
dBm
dBm
88Y6057-A SFP+, 10GBASE-SR 10G Ethernet Module 850mn, 300m, MMF, LC RoHS6
OMA, PRBS 231-1, BER < 1*10-12@10GBd OMA, PRBS 231-1, BER < 1*
[email protected] Pavg, PRBS 231-1, BER < 1*10-12@ 10.3125GBd OMA, PRBS 231-1, BER < 1*10-12@2GBd OMA, PRBS 231-1, BER < 1*10-12@4GBd OMA, PRBS 231-1, BER < 1*10-12@8GBd OMA, PRBS 231-1, BER < 1*
[email protected]
Stressed Receiver Sensitivity Ethernet Stressed Receiver Sensitivity Fiber Channel (OM3 fibers)
Loss of Signal
-10.8
-9.0
-11.1
PIN
PIN
tbd -7.5
-8.3
-17.5
Pav_as
POMA_deas
-12
Pav_deas
-17
Ethernet:1.25GBd *)
-30
Regulatory Compliance Module Safety
Approved Optics SFP+ modules are designed to meet international requirements and standards in terms of product safety. Tests were performed according to IEC 60950-1:2001 (CB scheme).The module is RoHS compliant according to the European Parliament requirements on the restriction of the use of hazardous substances in electrical and electronic equipment (RoHS). The modules optical output power meet Class 1 requirements for laser safety.
Requirements
Module Safety RoHS Compliance Laser Eye Safety
Standard
Status
IEC 60950-1:2001 EN 609501:2001 RoHS Directive 2002/95/EC Amendment 4054 (2005/747/EC) CDRH 21 CFR 1040.10 and 1040.11 IEC 60825-1 Rev2 2007
TUV Report / Certificate available CB Report / Certificate available RoHS 6/6 compliant Certificate of compliance available Laser Class 1 according to FDA Laser Class 1 according to IEC Rev2
ESD & Electromagnetic compatibility
Approved Optics SFP+ modules are designed to withstand high ESD voltages. Its excellent performances in terms of EMI allow system designers to integrate the module in high density applications.
Approved Networks, Inc.
www.ApprovedOptics.com
Page 6 of 8
dBm
dBm
dBm
88Y6057-A SFP+, 10GBASE-SR 10G Ethernet Module 850mn, 300m, MMF, LC RoHS6
Requirements Electro Static Discharge to the Electrical Pins (ESD)
Standard
EIA/JESD22-A114-B MILSTD 883C Method 3015.7
Immunity to ESD (housing, receptacle)
IEN 61000-4-2 IEC61000-4-2
Electromagnetic Emission (EMI)
Status
FCC Part 15, Class B EN 55022 Class B CISPR 22
Approved Networks, Inc.
Exceeds requirements Class 1B (>1000V) Exceeds requirements Discharges ranging from 2kV to 25kV without damages to the transceiver Exceeds requirements Class B with more than 6dB margin
www.ApprovedOptics.com
Page 7 of 8
88Y6057-A SFP+, 10GBASE-SR 10G Ethernet Module 850mn, 300m, MMF, LC RoHS6
Contact Information
Approved Networks is a leading supplier of Network Transceivers and Connectivity products to Channel Partners, Resellers, and OEMs. With more than 9 years of direct industry experience, Approved Optics, Inc., our products are resident in the most demanding and mission critical functional networks Worldwide. We serve as a Master Distributor to the largest CM’s in the world and deploy the most rigorous testing and firmware management programs to bring the highest level of functional product to the market at a cost that makes sense. Corporate offices: Approved Networks, Inc. Tel: 800.590.9535 Web: www.ApprovedOptics.com
Approved
Networks, Inc.
www.ApprovedOptics.com
Page 8 of 8
