Transcript
GB
USE AND MAINTENANCE MANUAL SILENT ELECTRIC ROTARY SCREW COMPRESSORS
AIRBLOK 75 - 100 DR/SD
WARNING: Read this manual carefully and in full before using the compressor. 1/50
IMPORTANT INFORMATION Read all the operational instructions, safety recommendations and all warnings provided in the instruction manual. Most accidents encountered when using the compressor are merely due to the failed observance of basic safety standards. Accidents are prevented by foreseeing potentially hazardous situations and observing the appropriate safety standards. The fundamental safety standards are listed in the “SAFETY” section of this manual and also in the section involving the use and maintenance of the compressor. Hazardous situations to be avoided in order to prevent serious personal injuries and machine damages are listed in the “WARNINGS” section of the instruction manual or are actually printed on the machine. Never use the compressor improperly but only as recommended by the Manufacturer. The Manufacturer reserves the right to up-date the technical information given in this manual without notice.
2/50
AIRBLOK 75 - 100 DR/SD
INDEX
I
GB
I
Index
0
Foreword ......................................................................................... 5
1
0.1
How to read and use the instruction manual ............................................. 5
0.1.a 0.1.b 0.1.c 0.1.d
Importance of the manual .................................................................................................... Conserving the manual ........................................................................................................ Consulting the manual ......................................................................................................... Symbols used ........................................................................................................................
General information........................................................................ 7 1.1 1.2 1.3
2
5
General description .................................................................................... 10 Intended use ................................................................................................ 10 Technical data ............................................................................................. 11
Transport, Handling, Storage ...................................................... 12 3.1 3.2 3.3
4
Identification data of the manufacturer and the compressor ................... 7 Information on machine technical/maintenance service .......................... 7 General safety warnings .............................................................................. 7
Preliminary machine information ................................................ 10 2.1 2.2 2.3
3
5 5 5 6
Transporting and handling the packed machine ..................................... 12 Packing and unpacking .............................................................................. 12 Storing the packed and unpacked compressor ....................................... 13
Installation ..................................................................................... 14 4.1 4.2 4.3 4.4
Admitted surrounding conditions ............................................................. 14 Space required for maintenance ............................................................... 14 Positioning the compressor ...................................................................... 15 Connecting the compressor to the sources of energy and relative inspections 16
4.4.1 4.4.2
Connecting the compressor to the electrical mains power supply ................................ 16 Connecting the dryer to the electrical mains ................................................................... 18
Using the compressor .................................................................. 19 5.1
Preparing to use the compressor .............................................................. 19
5.1.1 5.1.2
Operational principle .......................................................................................................... 19 Compressor operation with inverter versions “SD” (speed driven) .............................. 19
5.2
Controls, indicators and safety devices of the compressor ................... 20
5.2.1 5.2.2 5.2.3
Control panel ....................................................................................................................... 20 Auxiliary control devices .................................................................................................... 21 Description of the Electronic Control Unit ....................................................................... 21
5.3
Check the efficiency of the safety devices before starting ..................... 30
3/50
GB
I
INDEX
5.4 5.5
6
7
AIRBLOK 75 - 100 DR/SD
Starting the compressor ............................................................................ 30 Stopping the compressor .......................................................................... 30
Compressor maintenance............................................................ 31 6.1
Instructions relative to inspections and maintenance jobs. ................... 31
6.1.1 6.1.2 6.1.3 6.1.4 6.1.5 6.1.6 6.7.7 6.1.8 6.1.9 6.1.10 6.1.11
Changing the oil .................................................................................................................. Replacing the oil filter cartridge ........................................................................................ Replacing the filter cartridge of the oil separator ............................................................ Replacing the air filter cartridge ........................................................................................ .............................................................................................................................................. Cleaning the air/oil radiator ................................................................................................ Cleaning the dust-removal pre-filter ................................................................................. Grease the bearings of the motor ...................................................................................... .............................................................................................................................................. .............................................................................................................................................. ..............................................................................................................................................
6.2
Diagnosing the alarm status/inconveniences-faults ............................... 38
33 34 34 35 35 36 36 36 37 37 38
Drawings and diagrams ............................................................... 41 7.1 7.2 7.3
Wiring diagrams .......................................................................................... 41 Pneumatic diagrams ................................................................................... 46 Maintenance schedule
4/50
AIRBLOK 75 - 100 DR/SD
FOREWORD
0
Foreword
0.1
How to read and use the instruction manual
0.1.a
Importance of the manual
0
GB
This INSTRUCTION MANUAL has been written to guide you through the INSTALLATION, USE and MAINTENANCE of the compressor purchased. We recommend that you strictly observe all the indications given within as the ideal operational efficiency and lasting wear of the compressor depend on the correct use and methodical application of the maintenance instructions given hereafter. Remember that when any doubts or inconveniences arise it is a good rule to always contact the AUTHORISED SERVICE CENTRES. They are at your complete disposal for any explanations or jobs required. The Manufacturer therefore declines all liabilities regarding the incorrect use and poor maintenance of the compressor. The INSTRUCTION MANUAL is integral part of the compressor. Ensure that any up-dates forwarded by the Manufacturer are actually added to the manual. If the compressor is sold on at a later date the manual must be given to the new owner. 0.1.b
Conserving the manual Use and read the manual with care being careful not to damage any part of it. Do not remove, tear or re-write any parts of the manual for any reason whatsoever. Keep the manual in a dry and sheltered place.
0.1.c
Consulting the manual This instruction manual is made up of the following: • • •
FRONT COVER WITH MACHINE IDENTIFICATION DETAILED INDEX INSTRUCTIONS AND/OR NOTES ON THE COMPRESSOR
The model and serial number of the compressor to which the manual refers and that you have purchased is found on the FRONT COVER. The various SECTIONS in which all the notes relative to a certain subject are found in the INDEX. All the INSTRUCTIONS AND/OR NOTES ON THE COMPRESSOR aim at pointing out safety warnings and procedures required to use the compressor correctly.
5/50
GB 0.1.d
0
FOREWORD
AIRBLOK 75 - 100 DR/SD
Symbols used The SYMBOLS pointed out below are used throughout this manual and their purpose is that of drawing the operator’s attention, informing the latter how to behave and how to proceed in each operational situation.
READ THE INSTRUCTION MANUAL Read the use and maintenance manual carefully before installing and starting the compressor.
GENERAL HAZARDOUS SITUATION An additional note will point out the type of hazard involved. Meaning of the indications: Warning!
This points out a potentially hazardous situation, which if ignored, could cause personal injury and machine damage.
Note!
This enhances crucial information.
RISK OF ELECTRIC SHOCK Warning: the electrical power supply of the compressor must be disconnected before doing any jobs on the compressor.
RISK OF SCOLDING Warning: be careful when touching the compressor as some parts of it could be very hot.
6/50
AIRBLOK 75 - 100 DR/SD
GENERAL INFORMATION
1
General information
1.1
Identification data of the manufacturer and the compressor
1
GB
COMPRESSOR IDENTIFICATION NAMEPLATE (Example)
Silent electric rotary screw compressor.
1.2
Information on machine technical/maintenance service We remind you that our technical service department is at your complete disposal to help you resolve any problems that may possibly be encountered, or to provide you with any other information necessary. In the case of need contact: Our CUSTOMER TECHNICAL SERVICE department or your local dealer. The constant and efficient performance of the compressor is ensured only if original spare parts are used. We recommend therefore that you strictly observe the indications provided in the MAINTENANCE section and to use EXCLUSIVELY original spare parts. We suggest you visit our website: http://www.fiac-assistance.com The use of NON ORIGINAL spare parts automatically annuls the guarantee.
1.3
General safety warnings Note!
The procedures provided in this manual have been written to assist the operator throughout the use and maintenance of the compressor.
IMPORTANT INSTRUCTIONS FOR THE SAFE USE OF THE COMPRESSOR WARNING: THE INAPPROPRIATE USE AND POOR MAINTENANCE OF THIS COMPRESSOR MAY CAUSE PHYSICAL INJURY TO THE USER. YOU ARE RECOMMENDED TO CAREFULLY FOLLOW THE INSTRUCTIONS PROVIDED HEREAFTER TO AVOID SUCH RISKS. 1. DO NOT TOUCH MOVING PARTS Never put your hands, fingers or other parts of the body near moving parts of the compressor.
7/50
GB
1
GENERAL INFORMATION
AIRBLOK 75 - 100 DR/SD
2. NEVER USE THE COMPRESSOR WITHOUT THE SAFETY GUARDS FITTED Never use the compressor without all the safety guards fitted perfectly in their correct place (i.e. panelling, belt guard, safety valve). If these parts are to be removed for maintenance or servicing purposes, ensure that they are put back in their original place perfectly before using the compressor again. 3. ALWAYS WEAR SAFETY GOGGLES Always wear goggles or equivalent eye protection means. Never direct compressed air towards any part of your body or that of others. 4. PROTECT YOURSELF AGAINST ELECTRIC SHOCKS Avoid accidentally touching the metal parts of the compressor with your body, such as pipes, the tank or metal parts connected to earth. Never use the compressor where there is water or in damp rooms. For SD versions: Switch the electric control panel off and wait five minutes before removing the protection guards of the inverter to avoid possible electrical shocks. Using special testers, always ensure there is no voltage on the parts on which you are about to work. 5. DISCONNECT THE COMPRESSOR Disconnect the compressor from the electric power supply and completely discharge the pressure from the tank before carrying out any service, inspection, maintenance, cleaning, replacing or inspection jobs of each part. 6. ACCIDENTAL START-UP Never move the compressor while it is connected to the electrical power supply or when the tank is pressurised. Ensure that the main switch is turned OFF before connecting the compressor to the electrical power supply. 7. STORE THE COMPRESSOR APPROPRIATELY When the compressor is not in use, it must be stored in a dry room away from atmospheric agents. Keep it out of children’s reach. 8. OPERATIONAL AREA Keep the work area clean and remove any tools that are not required. Keep the work area sufficiently ventilated. Never use the compressor in the presence of flammable liquids or gas. The compressor may produce sparks while running. Do not use the compressor where there may be paints, gasoline, chemical compounds, glues and any other flammable or explosive material. 9. KEEP THE COMPRESSOR OUT OF CHILDREN’S REACH Prevent children or anyone else from touching the power supply cable of the compressor. All outsiders must be kept at a safe distance from the operational area. 10.WORK CLOTHES Do not wear unsuitable clothing, ties or jewellery as these may get caught up in moving parts. Wear caps to cover your hair if necessary. 11.PRECAUTIONS FOR THE POWER SUPPLY CABLE Do not disconnect the power supply plug by pulling on the cable. Keep the cable away from heat, oil and sharp edges. Do not stand on the electrical cable or squash it under heavy weights. 12.LOOK AFTER THE COMPRESSOR WITH CARE Follow the maintenance instructions. Inspect the power supply cable on a periodic basis and if damaged it must be repaired or replaced by an authorised service centre. Visually check the outside appearance of the compressor, ensuring that there are no visual anomalies. Contact your nearest service centre if necessary. 13.ELECTRICAL EXTENSIONS FOR OUTDOOR USE When the compressor is used outdoors, use only electrical extensions manufactured for outdoor use and marked as such. 14.WARNING Pay attention to everything you do. Use your common sense. Do not use the compressor if you are tired. The compressor must never be used if you are under the effect of alcohol, drugs or medicines, which could make you tired. 15.CHECK FAULTY PARTS OR AIR LEAKS Before using the compressor again, if a safety guard or other parts are damaged, they must be checked carefully to evaluate whether they may operate as established in complete safety. Check the alignment of moving parts, hoses, gauges, pressure reducers, pneumatic connections and every other part that may be crucial for the normal operational efficiency of the compressor. All damaged parts must be properly repaired or replaced by an authorised service centre or replaced following the instructions provided in instruction manual. 16.USE THE COMPRESSOR EXCLUSIVELY FOR THE APPLICATIONS SPECIFIED IN THIS INSTRUCTION MANUAL. The compressor is a machine that produces compressed air. Never use the compressor for purposes other than those specified in the instruction manual. 17.USE THE COMPRESSOR CORRECTLY Operate the compressor in compliance with the instructions provided in this manual. Do not allow children to use the compressor or those who are not familiar with it. 8/50
AIRBLOK 75 - 100 DR/SD
GENERAL INFORMATION
1
GB
18.ENSURE THAT EACH SCREW, BOLT AND GUARD IS FIRMLY SECURED IN PLACE. 19.KEEP THE IN-TAKE GRIDS CLEAN Keep the motor ventilation grids clean. Regularly clean these grids if the work area is particularly dirty. 20.OPERATE THE COMPRESSOR AT THE RATED VOLTAGE Operate the compressor at the voltage specified on the electrical data nameplate. If the compressor is used at a higher voltage than that rated, the motor could damage or burn out. 21.NEVER USE THE COMPRESSOR IF IT IS FAULTY If the compressor is noisy or vibrates excessively when running or it seems to be faulty, stop it immediately and check its efficiency or contact your nearest authorised service centre. 22.DO NOT CLEAN PLASTIC PARTS USING SOLVENTS Solvents such as gasoline, thinners, gas oil or other compounds that contain hydrocarbons may damage the plastic parts. Clean them with a soft cloth and soapy water or other suitable liquids. 23.USE ORGINAL SPARE PARTS ONLY The use of non-original spare parts involves the annulment of the guarantee and the abnormal running conditions of the compressor. Original spare parts are available c/o the authorised dealers. 24.DO NOT MODIFY THE COMPRESSOR Do not modify the compressor. Contact an authorised service centre for all repairs required. An unauthorised modification may impair the efficiency of the compressor and may also cause serious accidents for those who do not have the technical skill required to make such modifications. 25.TURN THE COMPRESSOR OFF WHEN IT IS NOT IN USE When the compressor is not in use turn the main ON/OFF switch OFF (position “0”). 26.DO NOT TOUCH HOT PARTS OF THE COMPRESSOR To avoid scolding do not touch pipes, the motor or any other hot part. 27.DO NOT DIRECT THE JET OF AIR DIRECTLY TOWARDS THE BODY To avoid all risks never direct the jet of air towards people or animals. 28.DO NOT STOP THE COMPRESSOR BY PULLING ON THE POWER SUPPLY CABLE Use the “O/I” (ON/OFF) switch to stop the compressor. 29.PNEUMATIC CIRCUIT Use recommended pneumatic hoses and tools that can withstand the same or a higher pressure than the maximum running pressure of the compressor. 30.SPARE PARTS Use only original and identical spare parts to replace worn or damaged ones. Repairs must be made exclusively by authorised service centres. 31.CORRECT USE OF THE COMPRESSOR The operator must be perfectly familiar with all the controls and compressor characteristics before starting to work with the machine. 32.MAINTENANCE JOBS The use and maintenance jobs of the commercial components fitted on the machine, but not indicated in this manual, are indicated in the enclosed documents. 33.DO NOT UNSCREW THE CONNECTION WHEN THE TANK IS PRESSURISED Do not unscrew the connection for any reason whatsoever with the tank pressurised without first checking if the tank is discharged. 34.DO NOT MODIFY THE TANK It is prohibited to intentionally drill, weld or deform the compressed air tank. 35.IF THE COMPRESSOR IS USED FOR PAINTING JOBS a) Do not work in closed rooms or near free flames. b) Ensure that the room in which you are working is sufficiently ventilated. c) Wear face and nose mask. 36.DO NOT PUT OBJECTS OR HANDS INSIDE THE PROTECTION GRID Do not put objects or hands inside the protection grid to avoid physical and material damages.
KEEP THESE USE AND MAINTENANCE INSTRUCTIONS CAREFULLY AND GIVE THEM TO PERSONNEL WISHING TO USE THE COMPRESSOR! WE RESERVE THE RIGHT TO MAKE MODIFICATIONS WHERE NECESSARY WITHOUT NOTICE
9/50
GB
2
PRELIMINARY MACHINE INFORMATION
AIRBLOK 75 - 100 DR/SD
2
Preliminary machine information
2.1
General description The rotary screw compressor has been specifically designed aiming at minimising maintenance and labour costs. The outside cabinet is completely covered in sound-proof and oil-proof panelling thus ensuring its extended and lasting wear. The components have been arranged so that all vital parts can be easily reached for maintenance purposes simply by opening dedicated panels with quick-release locking devices. The filters and adjustment and safety devices (oil filter, air filter, oil separator filter, regulator valve, minimum pressure valve, max. pressure safety valve, thermostat, belt tightener, screw compression unit, pressure switch and oil separator tank emptying and filling taps) are all fitted on the same side. Note!
The tanks of the compressors have been manufactured in compliance with the EEC/ 404/87 Directive for the European market. The compressors have been manufactured in compliance with the EC/37/98 Directive for the European market.
Note!
Check your model on the identification nameplate fitted on the compressor. It is also indicated in this manual.
ADVISED LUBRICANTS Always use oil for turbines with approximately 46 cSt at 40°C and a pour point of at least -8 +10°C. The flash point must be greater than +200°C. The oil in rotary screw compressors has the function of lubricating and cooling the screw unit. The oil also has a sealing function to ensure a perfect compression seal within the block. Therefore it is extremely important to choose the correct type of oil for this type of compressor.
NEVER MIX DIFFERENT OIL QUALITIES. SCREW OIL FOR DR/SD VERSIONS FIAC SYNT/RS D 46 OR IN ALTERNATIVE SHELL CORENA AS46 MOBIL RARUS SHC 1025 OR 100% SYNTHETIC OIL WITH THE SAME TECHNICAL CHARACTERISTICS AS THOSE LISTED ABOVE Use oil with VG32 rating for cold climates and VG68 for tropical climates. It is advisable to use synthetic oils for very hot and humid climates.
2.2
Intended use The silent rotary screw compressors have been designed and manufactured exclusively to produce compressed air. EVERY OTHER USE, DIFFERENT AND NOT FORESEEN BY ALL INDICATED, RELIEVES THE MANUFACTURER OF POSSIBLE CONSEQUENT RISKS. In any event the use of the compressor different to that agreed in the purchase order RELIEVES THE MANUFACTURER FROM ALL LIABILITIES WITH REGARD TO POSSIBLE MATERIAL DAMAGE AND PERSONAL INJURY. The electrical system is not designed for the use in environments subject to explosion or for flammable products.
NEVER DIRECT THE JET OF AIR TOWARDS PEOPLE OR ANIMALS. NEVER USE THE COMPRESSED AIR PRODUCED BY LUBRICATED COMPRESSORS FOR RESPIRATORY PURPOSES OR IN PRODUCTION PROCESSES WHERE THE AIR IS IN DIRECT CONTACT WITH FOODSTUFFS UNLESS IT HAS BEEN FIRST FILTERED AND CONDITIONED FOR SUCH PURPOSE.
10/50
Technical data
11/50
2200x1100x1950
IP
Protection rating
73
dB(A)
mm
Kg
Noise level (2000/14/CE)
Dimensions
Weight
1200
73
5/45
10 (DR)
Note! The technical data and dimensions of the machine are subject to variations at any time without notice
2200x1100x1950 1460
75
5/45
10 (DR)
S1
55
100/75
MEC280
≤1
12000
51
1” ½ G
335(DR)
10200(DR)
100÷335(SD)
2852÷10200(SD)
SCA14
10-145
2
The sound level may increase by 1 to 10 dB(A) depending on the room in which the compressor is installed.
1460
75
5/45
10 (DR)
S1
55
100/75
MEC280
≤1
12000
51
1” ½ G
445(DR)
12600(DR)
100÷445(SD)
2852÷12600(SD)
SCA14
8-116
AIRBLOK100 HP100
PRELIMINARY MACHINE INFORMATION
Sound level measured in a free range at a distance of 1 m: ±3dB(A) at the maximum working pressure.
1200
5/45
°C (min/max)
Ambient temperature limits
10 (DR)
S1
S1
N°
55
55
Max. starts per hour
Service
HP/kW
Output 75/55
MEC250
MEC250
IEC
2-pole electric motor 75/55
≤1
≤1
ppm
Oil residue in air
10100
m3/h
Fan capacity
51
1” ½ G
283(DR)
8015(DR)
100÷283(SD)
10100
51
l
317,7(DR)
cfm
Lubricant qty
9000(DR)
l/min
1” ½ G
100÷317,7(SD)
cfm
R
2830÷9000(SD)
l/min
Free air delivery ISO 1217
Air outlet fitting
SCA14
SCA14
Type of rotary screw end 2830÷8015(SD)
10-145
bar/psi
AIRBLOK75 HP75 8-116
Max. pressure
Model
2.3
AIRBLOK 75 - 100 DR/SD
GB
GB
3
2
PRELIMINARY MACHINE INFORMATION
AIRBLOK 75 - 100 DR/SD
Transport, Handling, Storage
In order to use the compressor in complete safety read the safety standards given in section 1.3. before reading this section.
3.1
Transporting and handling the packed machine
The packed compressor must be transported by qualified personnel using a forklift truck. Before moving the machine ensure that the load-bearing capacity of the forklift truck is sufficient to take the weight to be lifted. Position the forks exclusively as illustrated below. Once the forks have been positioned in the points indicated, lift slowly without jerking.
Never stand near the area where the compressor is being handled and never stand on the crate while it is being moved.
3.2
Packing and unpacking To avoid damages and to protect the compressor during transport it is usually placed on a wooden pallet, to which it is secured by screws and covered with cardboard. All the shipping and handling information and symbols are printed on the compressor packing. Upon consignment remove the top part of the packing and check if any damages have been encountered during transport. If any damages are found, caused during transport, immediately make a written claim, backed up with photos of the damaged parts if possible and forward everything to your insurance company, with copy to the Manufacturer and transporter.
12/50
AIRBLOK 75 - 100 DR/SD
PRELIMINARY MACHINE INFORMATION
2
GB
Using a forklift truck take the compressor as near as possible to the place where it is to be installed then carefully remove the protective packing without damaging it, following the instructions below: • Remove the securing screws and open cage 1. • Take the protective cardboard 2 off.
1
2
Note!
The compressor can be left on the packing pallet to make it easier to move.
Carefully ensure that the contents correspond with all written in the consignment documents. Dispose of the packing in compliance with current standards in force in the country of installation. Note!
3.3
The machine must be unpacked by qualified personnel using appropriate tools and equipment.
Storing the packed and unpacked compressor For the whole time that the compressor is not used before unpacking it, store it in a dry place at a temperature between +5°C and + 45°C and sheltered away from weather. For the whole time that the compressor is not used after unpacking it, while waiting to start it up or due to production stoppages, place sheets over it to protect it from dust, which may settle on the components. The oil is to be replaced and the operational efficiency of the compressor is to be checked if it is not used for long periods.
13/50
GB
4
4
INSTALLATION
AIRBLOK 75 - 100 DR/SD
Installation
In order to use the compressor in complete safety read the safety standards given in section 1.3. before reading this section.
4.1
Admitted surrounding conditions Position the machine as established when the order was placed. Failing this the Manufacturer is not liable for any inconveniences that may possibly arise. For SD versions, the cleanliness of the surrounding area is of extreme importance, as the compressor is equipped with suction filters on the electric fan of the electric control panel. Unless pointed out otherwise when placing the order, the compressor must work regularly in the surrounding conditions indicated below: ROOM TEMPERATURE The room temperature must not be lower than 5°C or higher than 45°C to ensure the ideal operational efficiency of the compressor. If the compressor works at a room temperature lower than the minimum value, the condensate could be separated within the circuit and therefore the water would mix with the oil, thus deteriorating the quality of the latter, failing to guarantee the even formation of the lubricating film between the moving parts with the possibility of seizure. If the compressor works at a room temperature higher than maximum value, the compressor would take in air that is too hot, which would prevent the heat exchanger from adequately cooling the oil in the circuit, raising the working temperature of the machine, thus causing the thermal safety device to trip, which stops the compressor due to an excessive temperature of the air/oil mixture at the screw outlet. The inverter dissipator could overheat, causing it to stop (for SD versions). The maximum temperature of the room is to be measured while the compressor is running. LIGHTING The compressor has been designed in compliance with legal prescriptions and in the attempt to minimise shadow zones to facilitate the operator’s job. The lighting system of the factory is to be considered as crucial for the operator’s safety. The room in which the compressor is installed must have no shadow zones, dazzling lights or stroboscopic effects due to the lighting. ATMOSPHERE WITH RISK OF EXPLOSION AND/OR FIRE The standard compressor is not pre-arranged or designed to work in rooms subject to the risk of explosion or fire. The performance of the compressor may decrease at the maximum permitted ambient temperature, with relative humidity higher than 80% and at an altitude of more than 1,000 mt. For SD versions, the maximum relative humidity at all altitudes is 95% without condensation.
4.2
Space required for maintenance The compressor must be installed in a large room that is well-aired, dust-free and sheltered away from rain and frost. The compressor takes in a large amount of air that is required to ventilate it internally. A dusty atmosphere would in time cause damages and inefficient performance. Part of the dust once inside is taken in by the air filter causing it to clog rapidly and another part of dust will settle on the components and will be blown against the cooling radiator, consequently compromising the efficiency of the heat exchanger. It is therefore obvious that the cleanliness of the area in which the compressor is installed is crucial for the correct efficiency of the machine, avoiding excessive running and maintenance costs. To facilitate maintenance jobs and to create a favourable circulation of air, the compressor must have a sufficient free space all around it (see fig.). The room must be provided with outlets that lead outdoors near the floor and ceiling that will allow the natural circulation of air. If this is impossible, some fans or extractors must be fitted to ensure an air flow rate 20% higher than the cooling air flow rate. Minimum recommended fan capacity: 2500 m3/h.
14/50
AIRBLOK 75 - 100 DR/SD
INSTALLATION
4
GB
1
min. 1000
min. 3200
200
H. min = 3500
2000 min. 5000 Ducts for the inlet and outlet of the air can be used in unfavourable environments. These ducts must be the same size as the in-take and delivery grid. If these ducts are longer than 3 meters contact the Authorised Service Centre. Note!
4.3
A conveyance system can be fitted to recover the hot ventilation air delivered, which can be used to heat the room or for other purposes. It is crucial that the cross section of the system that recovers the hot air is greater than the total cross section of the grid slots plus the system must be equipped with a forced extraction system (extractor fan 1) to favour a constant downflow. (minimum cross section 1200 cm²).
Positioning the compressor Once the position in which the compressor is to be installed has been identified ensure that the compressor is set on a flat surface. No special foundations or bases are required for the machine.
Do not secure the compressor rigidly to the floor.
15/50
GB
4
INSTALLATION
AIRBLOK 75 - 100 DR/SD
4.4
Connecting the compressor to the sources of energy and relative inspections.
4.4.1
Connecting the compressor to the electrical mains power supply
The compressor is to be connected to the electrical mains by the customer, to his exclusive liability, employing specialised personnel and in compliance with the Accident Prevention Norms EN 60204. INSTRUCTIONS FOR CONNECTING TO EARTH This compressor must be connected to earth while in use in order to safeguard the operator against electrical shocks. The electrical connection must be carried out by a skilled engineer. It is advisable never to dismantle the compressor or even to make any other connections. All repairs must be carried out exclusively by authorised service centres or other qualified centres. The earth wire of the power supply cable of the compressor must be connected only and exclusively to the PE pin of the terminal board of the actual compressor. Before replacing the plug of the power supply cable ensure that the earth wire is connected.
Avoid all risks of electrical shocks. Never use the compressor with damaged electrical cables. Regularly check the electrical cables. Never use the compressor in or near water or near a hazardous area where electrical shocks may be encountered ELECTRICAL CONNECTION The three-phase compressors (L1+L2+L3+PE) must be installed by a qualified engineer. The threephase compressors are supplied without plug and cable. The power supply cable must be fed into the electric cabinet through cable clamp 1 on the top of the electric cabinet.
1
Ensure that the cable cannot accidentally come into contact with moving or hot components, possibly secure with clips. The cross section of the wires of the power supply cable (Install in open catwalks and at maximum ambient temperature of 45°C) must be as follows: Power Hp 75 100
480V 35 mm2 50 mm2
Rated voltage 440V 35 mm2 70 mm2
380/415V 50 mm2 70 mm2
220/240V 95 mm2 120 mm2
You are recommended to install the socket and magnetothermal switch no further than 4 m from the compressor. The required characteristics of the magnetothermal switch are given in the table that follows. The fuses are already installed in the door locking switch and are the following type:
Power Hp
Rated voltage 380/415V Magneto thermal switch
75 100
160A 160A
220/240V Fuse
125A aM 160A aM 16/50
Magneto thermal switch
200A 315A
Fuse
200A aM 315A aM
AIRBLOK 75 - 100 DR/SD
INSTALLATION
for SD models: Power Hp
GB
Rated voltage 380/415V Magneto thermal switch
75 100
Note!
4
160A 160A
220/415V Fuse
125A aM 160A aM
Magneto thermal switch
200A 315A
Fuse
200A aM 315A aM
The parameters of the magneto thermal switches refer to switches type K.
Ensure the installed power in kW is at least double the input of the electric motor, for SD models, the installed power in kW must be the same as that absorbed by the compressor. All silent rotary screw compressors avail of Star/Delta starting, which enables the motor to start with as little electrical energy consumption upon start-up as possible. The mains voltage must correspond with that indicated on the electrical data nameplate of the machine; the admitted tolerance must remain within +/- 6%. EXAMPLE: Voltage, 400 Volt: minimum tolerance 376 Volt - maximum tolerance 424 Volt The plug of the power supply cable must never be used as a switch but must be plugged into a power socket that is controlled by an adequate differential switch (magneto thermal switch).
Never use the earth connection instead of the neutral. The earth connection must be achieved according to the EN 60204 industrial safety standards. Ensure that the mains voltage corresponds with that required for the correct operation of the compressor. CHECK THE ROTATION DIRECTION When connecting the compressor to the electrical mains for the first time ensure that the STOP ALARM is not triggered, which is pointed out by the red LED lit steady, by a buzzer and by a warning on the display 1 stating: ROTATION ALARM. This alarm points out the incorrect connection order of the electrical power supply cables (relative to the three phases) that causes the incorrect rotation direction of the screw unit. Once the cable connection has been rectified press the RESET key 3. Warning!
The incorrect rotation direction for more than 20 seconds will irreparably damage the compressor.
2 1
Note!
3
In SD models, the “ROTATION ALARM” means that the motor of the fan is running in the wrong direction. This causes the incorrect cooling of the radiator with consequent “TEMPERATURE ALARM”.
17/50
GB 4.4.2
4
INSTALLATION
AIRBLOK 75 - 100 DR/SD
Connecting to the pneumatic mains
Always use pneumatic hoses for compressed air with the maximum pressure characteristics and cross section suitable for those of the compressor. Do not try to repair a faulty hose.
1
Connect the compressor to the pneumatic mains using the fitting 1 pre-arranged on the compressor. Use hosing with a greater or same diameter as the compressor outlet. Install two ball taps with capacity suitable for the compressor between the compressor and tank and between the tank and line. Do not install nonreturn valves between compressor and tank. The non-return valve is already installed inside the compressor.
18/50
AIRBLOK 75 - 100 DR/SD
5
USING THE COMPRESSOR
5
GB
Using the compressor
In order to use the compressor in complete safety read the safety standards given in section 1.3. before reading this section.
5.1
Preparing to use the compressor
5.1.1
Operational principle The air taken-in by the filter passes through a valve that controls its flow rate to the screw where, mixing with the oil, it is compressed. The air/oil mix produced by compression reaches a tank where the initial separation by gravity is achieved; as the oil is heavier, it settles on the bottom, it is then cooled and sent through a heat exchanger, filtered and injected into the screw again. The oil is required to reduce the heat produced by compression, to lubricate the bearings and to maintain the coupling of the screw lobes. The air is sent through an oil separator filter to be additionally purified from residue oil particles. It is cooled by means of another heat exchanger and is finally outlet to be used at low temperature and with acceptable oil residues (≤1p.p.m.). A safety system controls the crucial points of the machine and points out any abnormal conditions. The temperature of the air/oil mix at the screw outlet is controlled by a thermostatic probe, which stops the compressor if the temperature is too high (105°C). The electric motor is equipped with a trip switch that immediately stops the compressor in the case of an over current caused by a mechanical or electric fault.
5.1.2
Compressor operation with inverter versions “SD” (speed driven) Principle of the speed of the inverter controlled compressor The mains pressure is monitored by a pressure transducer and transmitted to the frequency converter by means of an analogue input. The rated value set is transmitted to the inverter, which compares the values and, based on the requirements, adjusts the speed of the motor and consequently the output of compressed air, thus adapting to the pressure requested (0,5 bar less than that set). Speed of the motor The operating frequency of the motor may vary from 15Hz (approx.) to 65Hz (approx.), depending on the models there may be some differences. Whatever the case, you are recommended never to modify the speed values set by the manufacturer. A slower or faster speed set negligently could irreparably damage the motor. The motor is designed to run continuously in the frequency range set during testing. The motor has a power “plus” to compensate for filter clogging or possible pressure leaks. Adjustment Min. P.: Shut-down pressure Max. P.: Transfer pressure to idle running Inverter controlled compressors entail the following three phases: - Operation with speed modulation following the pressure set - Idle operation - stand-by. The motor varies the speed by modifying the speed of the compressor unit, therefore modifying the air output.
19/50
GB
5
USING THE COMPRESSOR
AIRBLOK 75 - 100 DR/SD
When the request for air is greater, therefore the line pressure drops, the inverter increases the speed of the motor, also increasing the air output. When the request for air is lower, the inverter reduces the speed of the motor, also reducing the air output, therefore the mains pressure is held constant as the air consumption varies. If the request for air is very low, the compressor proceeds at the minimum speed admitted, therefore consuming just the consumption energy required. If the request for air is zero, the compressor enters “idle” running mode for roughly two minutes and then it enters “STAND-BY” mode. If the line pressure falls below the minimum pressure set, the compressor starts again to guarantee the required air output, restoring the pressure at the correct values.
5.2
Controls, indicators and safety devices of the compressor
5.2.1
Control panel The control panel is made up of a set of buttons required for the main operational and control functions of the compressor. 1 GREEN LED This points out that the compressor is powered. 2 START (I) This button is used to turn the compressor on. 3 STOP (O) Press this button to turn the compressor off (delayed). 4 DEFAULT Compressor programming is exited by pressing this push button. 5 PROGRAM Programming is enabled by pressing this push button. 6 MENU SCROLLING PUSH BUTTON These four push buttons are used to scroll the menus displayed. 7 RESET Press this push button to cancel a procedure or to reset an alarm, provided the cause that triggered it has been eliminated. 8 RED LED This points out that an alarm has tripped. 9 DIGITAL DISPLAY The various menus are displayed and the parameters are monitored in this display. 9 8
1
7
2
5
4
3
10 6
20/50
AIRBLOK 75 - 100 DR/SD
USING THE COMPRESSOR
5
GB
10 EMERGENCY PUSH BUTTON This mechanically blocking push button is used to immediately stop the compressor in the case of emergency. With the push button blocked it is impossible to start the compressor. To be able to start the compressor again, turn the emergency push button up then press the RESET button. 5.2.2
Auxiliary control devices 1 OIL THERMAL PROTECTION SWITCH RESET BUTTON This is positioned on the side of the electrical cabinet inside the compressor. Press this button to reset the oil thermal protection switch.
1
5.2.3
Description of the Electronic Control Unit Rotary screw compressors are equipped with an Electronic Control Unit, the control panel of which is described in point 5.2.1. The ECU controls machine operation in an efficient and safe manner. When the compressor is connected for the first time at the rated electrical voltage, ensure the STOPPED ALARM does not trigger, which is pointed out by the red LED that lights up steady (ALARM on dashboard), by a beeping buzzer and by a message that flashes on the display, indicating: ALARM ROTATION This alarm means that the electrical power supply cables are connected incorrectly (relative to the three phases), which would cause the screw unit to turn in the wrong direction. For SD models, the wrong rotation direction is that of the motor of the radiator fan. If this occurs, the machine is absolutely unable to start. Once you have connected the cables correctly, press the RESET key on the dashboard to set the compressor ready to start again correctly.
21/50
GB
5
USING THE COMPRESSOR
AIRBLOK 75 - 100 DR/SD
CHECKING THE SETTINGS 1) When the machine is ready, “PRESS START TO START” appears on the display. You can check the overall setting of the control unit by pressing the “UP arrow” or DOWN arrow” keys of the push button control panel: Note! Refer to the menu descriptions to better comprehend the meaning of the parameters listed hereafter. ALARM OIL TEMPERAT (---)
STAR-DELTA TIME (---)
No.PRESSURE ALARMS (---)
PRESS.SENSOR SETUP (---)
BUZZ. (y/n) (1/2) (---)
No. MOTOR THERM.ALARMS (---)
LANGUAGE CHOICE (0-4) (---)
IDLE RUN TIME (---)
No.MOTOR TEMP. ALARMS (---)
SELECT PSI/BAR 2/1 (---)
MAX P. CUSTOMER SETUP (---)
No. OIL LOW TEMP AL. (---)
SELECT FAR/CELS 2/1 (---)
MIN P. CUSTOMER SETUP (---)
HOURS WORKED (---)
REN.CONTR. (2/1) (y/n) (---)
MAINTENTENANCE TIME (---)
HOURS OF COMPRESSION (---)
ALARM PRESSURE (---)
No.OIL TEMP. ALARMS (---)
NET SWITCH OFF HOUR (---)
Press the DEFAULT key to exit.
2) Press the “left arrow” and the “right arrow” key on the push button control panel to view the following on the display for a few seconds: - Total hours of operation (OL) - Hours of operation under load (OC) - Number of hours left to maintenance (MANUT) Example: TH: LH:
150 - - MAINTEIN 100 - - 2850
Where: OL = 150 h OC = 100 h MANUT = 2850 h MENUS THE CLIENT CAN ACCESS PASSWORD “< + DEFAULT” “> + DEFAULT”
MENU AUTOTEST CLIENT
HOW TO ACCESS HOW TO EXIT Keys < and DEFAULT pressed together “STOP” key Keys > and DEFAULT pressed together “DEFAULT” key
AUTOTEST (“< + DEFAULT” simultaneously) To access the menu, press the < and DEFAULT keys simultaneously. The AUTOTEST function automatically checks the electrical connections of the machine. TESTING STOP TO EXIT To exit the AUTOTEST function, press the Stop button as indicated on the display. 22/50
AIRBLOK 75 - 100 DR/SD
USING THE COMPRESSOR
5
GB
CLIENT MENU (“> + DEFAULT” simultaneously) To access this menu, press keys > and DEFAULT simultaneously. The CLIENT MENU enables you to calibrate the following parameters: 1. Cut-in pressure of the compressor (Min. P.) 2. Cut-off pressure of the compressor (Max. P.) 3. Idle running time To scroll the parameters indicated, press the “DOWN arrow” and “UP arrow” keys of the push button control panel and press the “DEFAULT” key to exit.
1.
MIN.P.CUSTOMER SETUP (8.0)
To change the Min. P. value (equal to 8 bar in the example given), press “PROGRAM” and enter the replacement value in decimals, without commas using the “DOWN arrow” and “UP arrow” keys of the push button control panel and press “PROGRAM”. i.e.: To set Min. P. = 7.5 bar - press “PROGRAM” - enter “75” - press “PROGRAM” Note!
Min. P. Must be greater than or equal to 5.5 bar/79.8 psi (Max. P. – Min. P.) must be greater than or equal to 1 bar/14.5 psi
To exit the menu, press the “DEFAULT” key.
2.
MAX.P.CUSTOMER SETUP (10.0)
To change the Max. P. value (equal to 10 bar in the example given), press “PROGRAM” and enter the replacement value in decimals, without commas using the “DOWN arrow” and “UP arrow” keys of the push button control panel and press “PROGRAM. Note!
Max. P. must be at least 0.5 bar/7.2 psi lower than the Alarm P. (Max. P. – Min. P.) must be greater than or equal to 1 bar/14.5 psi
To exit the menu, press the “DEFAULT” key.
3.
IDLE RUN TIME (240)
Specify the idle running time of the compressor in seconds. To modify it, enter the new value using the “UP arrow” and “DOWN arrow” keys of the push button control panel, (in seconds) and then press “PROGRAM”. Note!
The minimum idle running time is 120 sec, the maximum value is 600 sec.
To exit the menu, press the “DEFAULT” key.
4.
METER SET ZERO KW (2321)
Specify the value of the kwh consumed up to the current time from the last reset. Enter “0” (Zero) to reset the meter. To exit the menu, press the “DEFAULT” key.
23/50
GB
5
USING THE COMPRESSOR
AIRBLOK 75 - 100 DR/SD
To summarise: CALIBRATION LIMITS - Max. P. < Alarm P. - 0.5 bar/7.2 psi - Min. P. > 5.5 bar/79.8 psi - DP = (Max. P. – Min. P.) > 1 bar/14.5 psi - 120 s < IDLE RUNNING TIME < 600 sec - “0” to reset the meter. The “Alarm P.” can be modified from the manufacturer’s “SETTING” menu. ALARMS The alarms that may trigger can be grouped in two categories: A) Stopped ALARM (red steady LED) B) Warning ALARM (red flashing LED) C) INVERTER stopped and warning ALARMS (Red steady or flashing LED)
A) Stopped ALARM This type of alarm stops the compressor and is pointed out by the red steady LED (ALARM on dashboard), by a beeping buzzer and by a flashing message on the display indicating the cause for the actual alarm. 1. When the Pressure exceeds the limit alarm pressure (case in which the increase in pressure is so quick that the max. cut-off pressure is unable to intervene) the following appears on the display: ALARM PRESSURE THE COMPRESSOR STOPS! To reset the machine: Once the pressure has dropped (P < Alarm P.) press the “RESET” key to set the compressor ready to start again. At this stage the following appears on the display: PRESS START TO START 2. When the limit oil-air temperature is exceeded (T>alarm T.=105°C/221°F) the following appears on the display:
ALARM TEMPERATURE THE COMPRESSOR STOPS! To reset the machine: Once the temperature has dropped by at least 10°C/18°F compared to the limit temperature, you can RESET the compressor internally (you need to open the front hatch and then press the board RESET button).
1
24/50
AIRBLOK 75 - 100 DR/SD
USING THE COMPRESSOR
5
GB
3. When the electric motor of the radial fun overheats, the following appears on the display: THE COMPRESSOR STOPS! ALARM THERMIC To reset the machine: Wait for the temperature of the fan motor to cool down to normal conditions Once you have eliminated the overheating causes, press the “RESET” key on the control dashboard. The thermal sensor is inside the fan motor, therefore you need to wait for it to cool down. 4. The following may appear on the display: THE COMPRESSOR DOES NOT START! ALARM ROTATION This alarm means that the electrical power supply cables have been connected incorrectly (relative to the three phases). When connected correctly, the screw unit and the fan motor will run in the correct direction. In SD models, only the fan motor can run in the incorrect direction. To reset the machine: Once you have connected the cables correctly, press the “RESET” key on the control dashboard. 5. The following may appear on the display:
ALARM LOW TEMPERATURE THE COMPRESSOR WILL NOT START BACAUSE THE SCREW UNIT IS TOO COLD (-6°C). To reset the machine: If the temperature increase to –5°C, press the “RESET” key to set the compressor ready to start. 6. The following may appear on the display: THE COMPRESSOR STOPS! The PTC in the motor points out an excessively high internal temperature. ALARM MOTOR TEMPERATURE To reset the machine: If the temperature of the motor drops back down to normal values, eliminate the triggering causes and press the “RESET” key to set the compressor ready to start again. B) Warning ALARM This type of alarm does not actually stop the compressor and is pointed out by the red flashing LED (ALARM on dashboard), by a beeping buzzer and by a flashing message on the display indicating the warning.
1.
WARNING AIR FILTER This points out that the air filter is clogged. Replace it or clean it as soon as possible.
25/50
GB
5
USING THE COMPRESSOR
AIRBLOK 75 - 100 DR/SD
WARNING OIL SEPAR. FILTER
2.
This points out that the oil separator filter in the separator tank is clogged. Replace the filter as soon as possible. WARNING MAINTENANCE TIME
3.
This points out that the pre-established maintenance time has expired. Carry out the maintenance jobs stated herein. To reset the maintenance hours, see item 1 and 2 of the “MAINTENANCE” menu. Note!
If the alarm flashes without the display indicating the cause, press the “UP” and “DOWN” arrow keys on the push button control panel together at the same time to view an indication on the cause.
C) INVERTER ALARMS (SD) Stopped and Started In the case of an anomaly or fault in the inverter, some alarms appear on the control unit on two different lines of the viewer: STATUS WORD1 and STATUS WORD2 with a number of special codes that identify the type of fault and possible solution. These alarms cause the compressor to stop. The alarm is pointed out by the red flashing LED and buzzer. A list of all the types of alarms that may trigger together with their possible solutions follows below. The following could appear on the display:
1.
STATUS WORD1: 00001 Short-circuit in motor cables or motor. THE COMPRESSOR STOPS! Solution: Check the motor cables and the motor. Ensure there are no correction condensers of the power factor or input circuits of the transistors in the motor cable. Or: There is a fault in output bridge of the transformer. THE COMPRESSOR STOPS! Solution: Contact the manufacturer. To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Press the “RESET” key on the control board to set the compressor ready to start again.
2.
STATUS WORD1: 00002 Excessive output current. The tripping limit for the overcurrent is 3.5xI2hd. THE COMPRESSOR STOPS!
26/50
AIRBLOK 75 - 100 DR/SD
USING THE COMPRESSOR
5
GB
Solution: Check the motor load. Check the motor and the motor cable (including the timing). Ensure there are no correction condensers of the power factor or input circuits of the transistors in the motor cable. To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Then press also the “RESET” key on the control board to set the compressor ready to start again.
3.
STATUS WORD1: 00004 Excessive dc voltage in the intermediary circuit. The tripping limit for the dc overvoltage is 1.3xU1max, where U1max is the maximum value of the mains voltage interval. For 400V units, U1max is 415V. For 500V units, U1max is 500v. The actual voltage of the intermediary circuit corresponds to the tripping level of the mains voltage, namely 728V dc. for 400V units and 877 dc. for 500V units. THE COMPRESSOR STOPS! Solution: Check for excessive static or transitory voltages in the mains. To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Then press also the “RESET” key on the control board to set the compressor ready to start again.
4.
STATUS WORD1: 00008
The temperature within the inverter is excessive. The tripping level of the temperature of the inverter module is 125°C. THE COMPRESSOR STOPS! Solution: Check the surrounding conditions. Ensure there is sufficient air circulation and check if the fan of the electric control panel is working. Ensure there is no dust on the fins of the inverter dissipator. Ensure the filters on the hatch of the electric control panel are not dirty. To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Then press also the “RESET” key on the control board to set the compressor ready to start .
5.
STATUS WORD1: 00016
The load on the input mains system is unbalanced. This may be determined by a fault in the motor, the motor cable or an internal anomaly. THE COMPRESSOR STOPS! Solution: Check the motor and the motor cable. Ensure there are no correction condensers of the power factor or input circuits of the transistors in the motor cable.
27/50
GB
5
USING THE COMPRESSOR
AIRBLOK 75 - 100 DR/SD
To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Then press also the “RESET” key on the control board to set the compressor ready to start. 6.
STATUS WORD2: 00001
The dc voltage of the intermediary circuit oscillates due to missing mains phase, blown fuse or fault inside the rectifier bridge. The device trips when the ripple of the dc voltage is equal to 13% of the dc voltage. THE COMPRESSOR STOPS! Solution: Check the mains fuses. Check for anomalies in the mains power supply. To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Then press also the “RESET” key on the control board to set the compressor ready to start.
7.
STATUS WORD2: 00004
The dc voltage of the intermediary circuit is insufficient due to a missing mains phase, blown fuse or an internal fault of a rectifier bridge. The tripping limit of the minimum dc voltage is 0.65xU1min, where U1min is the minimum value of the mains voltage interval. For 400V and 500V units, U1min is 380V. The actual voltage in the intermediary circuit corresponds to the tripping level of the mains voltage, namely 334Vcc. THE COMPRESSOR STOPS! Solution: Check the mains power supply and the fuses. To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Then press also the “RESET” key on the control board to set the compressor ready to start. 8.
STATUS WORD2: 00128 The temperature of the control board is lower than –5…..0°C or higher than +73……82°C. THE COMPRESSOR STOPS! Solution: Check if there is sufficient air circulation and if the fan of the inverter and that of the electric cabinet are working. Check the state of the filters of the electrical cabinet. To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Then press also the “RESET” key on the control board to set the compressor ready to start.
9.
STATUS WORD2: 01024
28/50
AIRBLOK 75 - 100 DR/SD
USING THE COMPRESSOR
5
GB
The analogue control signal is lower than the minimum value admitted due to an insufficient signal level or to an error in the connection of the control unit. THE COMPRESSOR STOPS! Solution: Check if the levels of the analogue control signal are correct. Check the control cabling. To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Then press also the “RESET” key on the control board to set the compressor ready to start. 10. STATUS WORD2: 04096
Loss of cyclic communication between the drive and the master station. THE COMPRESSOR STOPS! Solution: Check the fieldbus communication status. Check the connections of the cables. Check if the master is able to communicate. To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Then press also the “RESET” key on the control board to set the compressor ready to start. 11. STATUS WORD2: 16384
The motor nearly stalls, for example due to excessive loads or insufficient motor power. THE COMPRESSOR STOPS! Solution: Check the load of the motor and the drive data nameplate. To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Then press also the “RESET” key on the control board to set the compressor ready to start. 12. STATUS WORD2: 32768 A motor phase is lost due to a fault in the actual motor, motor cable or internal fault. THE COMPRESSOR STOPS! Solution: Check the motor and motor cable. To restore machine operation: Eliminate the cause for the fault. Press the RESET button on the keypad of the ACS800 INVERTER inside the electric cabinet. Then press also the “RESET” key on the control board to set the compressor ready to start.
29/50
GB 5.3
5
USING THE COMPRESSOR
AIRBLOK 75 - 100 DR/SD
Check the efficiency of the safety devices before starting OIL LEVEL Check the oil level as indicated in Section 6 “Compressor maintenance”.
DO NOT START THE COMPRESSOR WITH THE GUARDS OPEN TO AVOID INJURY DUE TO MOVING COMPONENTS OR ELECTRICALLY POWERED EQUIPMENT.
5.4
Starting the compressor
Following an electrical shortage the compressor will start only if the START (I) button is pressed. Ventilation must occur as illustrated below. It is of crucial importance that the compressor works with all the panels firmly closed. The failed observance of these and the following standards may lead to accidents that could cause personal injury and serious damages to the compressor or its equipment.
Before initially starting the compressor or following extended inoperation, you need to start the machine intermittently by pressing the START(I)-STOP(O) buttons alternately for 3 or 4 seconds. It is then advisable to run the compressor for a few minutes with the air outlet tap open. Gradually shut-off the air tap and load to the maximum pressure, checking if the inputs on each phase of the electric power supply are within the limits and if the pressure on the display of the board is correct and if the maximum pressure set triggers compressor idle running mode. At this stage, check if the compressor runs idle for roughly 2 minutes. The pressure on the gauge of the oil separator tank must be between 2 and 3 bar. At the end of this time, the compressor stops, triggered by the timer. Release the air from the tank to restore the starting pressure (9 bar), shut-off the air outlet tap and wait for the board to trigger the opening of the suction valve and the closure of the internal discharge.
5.5
Stopping the compressor Press the STOP (O) push button and the compressor will stop immediately. Note!
By disconnecting the power supply from the external switch the compressor is completely without power.
30/50
AIRBLOK 75 - 100 DR/SD
6
COMPRESSOR MAINTENANCE
6
GB
Compressor maintenance
In order to use the compressor in complete safety read the safety standards given in section 1.3. before reading this section.
6.1
Instructions relative to inspections and maintenance jobs. The table that follows summarises the periodic and preventative maintenance jobs required to keep the compressor in an efficient operational state in time. A brief description of the running hours after which the type of maintenance job is required.
Before performing any jobs within the sound-proof cabinet, ensure that: • The main line switch is turned off (position “0”) • The electrical compressor switch is Off in position “0” • The compressor is disconnected from the compressed air system • All the pressure has been released from the compressor and internal pneumatic circuit. The front panels are equipped with quick-release locks to facilitate maintenance and any other jobs necessary. Weekly: it is advisable to inspect the compressor, paying special attention to oil leaks and scale due to settled dust and oil. Note!
If the compressor is used for more than 3000 hours/year the jobs indicated herewith are to be performed more often. If the compressor is used in particularly hot and humid surroundings, or in any other harsh conditions, you need to reduce the maintenance interval times.
31/50
GB
6
COMPRESSOR MAINTENANCE
AIRBLOK 75 - 100 DR/SD
Interval (hours)
Jobs to be performed
See section
weekly
Check if the filters of the electric cabinet are clogged (for versions SD) ... Check if the anti-dust pre-filter is clogged ..............................
6.1.9 6.1.7
500 hours following first start-up
Check the oil level ................................................................. Check the electrical connections and tighten if necessary .....
6.1.1
every 2500 hours or at least once a year
Replace the oil filter cartridge ................................................ Replace the filter cartridge of the oil separator ...................... Replace the air filter cartridge ................................................ Check the joint ....................................................................... Clean the air/oil radiator ......................................................... Check filters in electrical cabinet and replace if necessary .... Grease the motor bearings .................................................... Clean inverter dissipator (for SD versions) ............................ Check the safety valve .......................................................... Check the electrical connections and tighten if necessary .....
6.1.2 6.1.3 6.1.4 6.1.5 6.1.6 6.1.9 6.1.8 6.1.11
every 5000 hours
Change the oil .......................................................................
6.1.1
every 7500 hours
Check the hydraulic seals ..................................................... Test motor trip switch (for DR versions) ................................ Test oil trip switch .................................................................. Overhaul the suction valve ....................................................
every 12500 hours
Check the hoses and replace if necessary............................ Overhaul oil separator flange ................................................ Grease the minimum pressure valve ..................................... Replace Fluorflon pipes 6x4 and 10x10 ................................ Replace the screw oil seal .................................................... Replace the bearings of the radiator fan motor (to be done by FIAC Technical Service centre) ............................................. Replace the delivery OR flange .............................................
every 20000 hours
Replace inverter fan (for SD versions) .................................. Replace the bearings of the motor (to be done by FIAC Technical Service centre) ........ Replace the bearings of the screw (to be done by FIAC Technical Service centre) ........
6.1.10 6.1.8
The above described maintenance schedule has been planned bearing in mind all the installation parameters and recommended use of the Manufacturer. The Manufacturer advises the customer to keep a record of all maintenance jobs performed on the compressor, see Section 7 – Drawings and diagrams. 32/50
AIRBLOK 75 - 100 DR/SD
6.1.1
COMPRESSOR MAINTENANCE
6
GB
Changing the oil Read all the information provided in Section 6.1 before proceeding with any maintenance jobs. Change the oil following the initial 500 hours of use and then every 5000 hours and in event once a year. Open the front panel to access the internal parts of the compressor. Unscrew cap 1 on the separator tank. Take cap 2 off. Screw the fitting with tail piece 3 (supplied with the compressor).
As the knurled fitting 1 is turned oil starts to seep out from the screw unit, therefore use a hose and container to collect the oil. Once all the oil has been drained remove the knurled fitting 3 and screw cap 2 manually. Top up with oil to half way up inspection glass 4, then screw cap 1 back on and close the compressor. Once the oil and oil filter have been changed leave the compressor to run for roughly 5 minutes then turn it off and check the oil level again. Check the oil level once a month. Ensure it is half way up inspection glass 4.
1
4
3
2
Never mix different types of oil, therefore always ensure that the circuit is completely empty before filling-up with oil. Each time the oil is changed the filter is also to be replaced. 33/50
GB 6.1.2
6
COMPRESSOR MAINTENANCE
AIRBLOK 75 - 100 DR/SD
Replacing the oil filter cartridge Read all indicated in Section 6.1 before starting any maintenance jobs. Replace the oil filter cartridge after the first 500 hours of use then every 2500 hours and in any event each time the oil is changed. Open the front panel. Disassemble filter cartridge 1, using a chain spanner and replace with a new one. Lubricate the sealing gasket before screwing the filter cartridge tight. Manually tighten the new filter cartridge.
1
6.1.3
Replacing the filter cartridge of the oil separator Read all indicated in Section 6.1 before starting any maintenance jobs. Open the front panel to gain access to inside the compressor. Disconnect the compressed air hoses from the hose fittings 1. Loosen nut 3 and disconnect pipe 2. Unscrew the nuts 4 and lift the cover 5 to access inside the separator tank. Replace the old filter with a new one 6. Follow the procedure in reverse order to fit the parts disassembled back in place.
1 3 2
6 4
5 34/50
AIRBLOK 75 - 100 DR/SD
6.1.4
COMPRESSOR MAINTENANCE
6
GB
Replacing the air filter cartridge Read all indicated in Section 6.1 before starting any maintenance jobs. Open the top panel to access inside the compressor. Take the cover off 1. Replace the cartridge of the air filter 2 and fit the cover back in place.
1
2
6.1.5
Joint On a periodic basis, visually inspect the joint 2 based on the hours of operation indicated in the maintenance table. Ensure it operates silently and that there are no splits or other damages in the orange flexible part. Proceed as follows: Check if there are any abnormal noises during operation. Stop the compressor. Disconnect the power supply of the compressor by switching the main ON/OFF switch OFF and make sure it cannot be switched ON again accidentally. Unscrew the protection grid 1. Manually turn the joint and check its state. If you notice any damages, contact an authorised Service centre of the Manufacturer to have it replaced! If no damages or problems are noticed, screw the protection grid back in place. Close the external maintenance panel.
1
2 35/50
GB 6.1.6
6
COMPRESSOR MAINTENANCE
AIRBLOK 75 - 100 DR/SD
Cleaning the air/oil radiator Read all indicated in Section 6.1 before starting any maintenance jobs. It is advisable to clean the radiator 1 on a weekly basis to remove impurities, blowing it with an air gun from inside. Open the left panel and blow compressed air from the inside of the radiator.
1
6.1.7
Cleaning the dust-removal pre-filter Read all indicated in Section 6.1 before starting any maintenance jobs. Clean the pre-filter 1 from impurities on a weekly basis. Slide the pre-filter 1 out and blow with compressed air or replace if necessary.
1
6.1.8
Grease the bearings of the motor. Put new lubrication grease in the motor bearings, using the special lubricator. To lubricate (with roughly 35g of grease), take the tap off the grease discharge on the shield. Always clean the grease cap and turn the shaft so that the grease spreads right around the bearing. When the motor is running, right after the bearing has been lubricated, the temperature of the actual bearing will increase by 10°-15° just momentarily, to then settle back down at the normal temperature when the grease has spread evenly and any excess grease has been expelled from the bearing tracks. If bearings are lubricated excessively they would overheat. When you have finished lubricating the bearing, put the grease discharge tap back in place.
Clean the supports and renew the grease Whatever the hours of operation, the grease is to be renewed after 1-2 years and also when generally overhauling the compressor. Once the motor has been dismantled, clean all parts of the bearing and the support to remove all the old grease, dry them, check the state of wear of the bearing and replace if necessary. Fill all the empty gaps inside the bearing with new grease. The gaps at the side of the support are not to be filled. Types of recommended grease To grease the bearings efficiently, use exclusively grease for high temperatures type Esso Unirex N3. The manufacturer declines all forms or liability with regard to damages to bearings caused by the use of alternative grease. Do not mix different types of grease (oil pulp, base oil), which reduces the quality of the oil and is therefore to be avoided. 36/50
AIRBLOK 75 - 100 DR/SD
COMPRESSOR MAINTENANCE
6
GB
Replace the bearings This job is to be done by the Technical Service centre after carefully inspecting the bearings. It is advisable to replace the bearings after: 36.000 hours of operation if the compressor is used in normal conditions (ambient temperature up to 25°C). 20.000 hours of operation if the compressor is used in harsher conditions (ambient temperature up to 40°C). 6.1.9
Cleaning the filters of the electrical cabinet Clean the filters (1) once a month by unscrewing and removing the guard (2) and blowing them with compressed air. If the machine works in a dusty environment, it is advisable to clean the filters more frequently based on their condition. Replace the filter after it has been cleaned five times or if the environment is particularly dusty.
1
2
2
6.1.10
Replacing the inverter fan and radiator fan bearings The fan of the inverter and the supplementary fan above it are to be replaced every 20000 hours of operation.The bearings of the radiator fan are to be replaced, in normal conditions of use, every 12500 hours, whereas they are to be replaced every 6000 hours in the case of harsher working conditions (ambient temperature up to 40°C). To remove the fan, unscrew the screws that secure it in place (1). Disconnect the cable. Connect the fan following the instructions in reverse order. Contact an authorised centre for its replacement.
1 37/50
GB 6.1.11
6
COMPRESSOR MAINTENANCE
AIRBLOK 75 - 100 DR/SD
Cleaning the dissipator (only for version SD) Dust transported by the cooling air may settle on the fins of the dissipator. If the dissipator is not cleaned regularly, the drive may encounter alarms and faults due to overheating. In “normal” surroundings (neither dusty or clean), the dissipator must be cleaned and inspected on a yearly basis, but more often in dusty surroundings. Clean the dissipator as follows: Remove the cooling fan.
Blow DRY compressed air from the bottom upwards and simultaneously use a vacuum cleaner on the air outlet to clean away the dust. Cover any equipment nearby with sheets to protect them against the dust expelled. Re-install the cooling fan.
6.2
Diagnosing the alarm status/inconveniences-faults
Before doing any job on the compressor ensure that: • The main ON/OFF switch is turned Off (position “0”) • The electric compressor switch is disabled in position “0” • The compressor is shut-off from the compressed air system • The compressor and the internal pneumatic circuit are completely de-pressurised If you are unable to rectify the anomaly encountered on your compressor contact your nearest authorised service centre. COMPRESSOR Anomalies
Cause
Solution
The machine stops, as the oil Excessive temperature of air/ Check the oil level. Check if the radiator is alarm has triggered (red oil mix outlet from the screw clean. Check if the dust removal pre-filter is LED). (105 °C). clean. Check the ambient temperature and the minimum distance of the compressor from the walls in the room. Check if the mobile soundproof panels are firmly secured in place (pressurisation of the ventilation air). Ambient temperature too high, air discharge channels too narrow or too long. Check oil level and if the type of oil is correct. Check if the oil filter is clogged. To start the machine again, open the front panel of the compressor, press the reset key on the right side of the electrical system (see button 1 point 5.2.2) and the RESET key of the board, then press START.
38/50
AIRBLOK 75 - 100 DR/SD
Anomalies
COMPRESSOR MAINTENANCE
Cause
6
GB
Solution
The machine stops, as the Compressor motor trip switch Ensure the electrical power supply is correct, compressor motor trip switch tripped. checking if the three power supply phases has tripped (red LED). are around about the same value. Ensure the cables are firmly connected to the terminal board and make sure the electrical cables have not melted. Ensure the suction grid of the cooling fan of the motor is not dirty or obstructed with foreign objects (paper, leaves, rags). To start the machine again, wait for the motor to cool down. The machine works with two phases due a fault in the motor or due to a blown fuse, therefore have the motor repaired by an authorised Fiac SpA centre if necessary or replace the blown fuse. If the machine fails to depressurise, check the depressurisation line and excessive ambient temperature, in which case ventilate the room and lower the temperature to below 45°C. The machine stops, as the Radiator fan motor trip switch Ensure the electrical power supply is correct, checking if the three power supply phases radiator fan motor trip switch tripped. are around about the same value. Ensure has tripped (red LED). the cables are firmly connected to the terminal board and make sure the electrical cables have not melted. Ensure the suction grid of the cooling fan of the motor is not dirty or obstructed with foreign objects (paper, leaves, rags). To start the machine again, wait for the motor to cool down. The machine works with two phases due a fault in the motor or due to a blown fuse, therefore have the motor repaired by an authorised Fiac SpA centre if necessary or replace the blown fuse. If the ambient temperature is too high, ventilate the room and lower the temperature to below 45°C. The compressor is running The suction valve fails to open. Check if the pressure probe is working but fails to load. correctly and also if the commanding solenoid valve (NC solenoid valve) is working regularly. Check the running direction of the motor and modify if necessary to avoid irreparable damages to the compressor. The nonreturn valve or minimum pressure valve could be faulty, therefore have them replaced by an authorised service centre. Tighten any loose pipes and joints. It could also be that the air demand is excessive, therefore you need to install another compressor in parallel. The compressor could be faulty, therefore contact an authorised Service centre to have it repaired.
39/50
GB
6
COMPRESSOR MAINTENANCE
Anomalies
AIRBLOK 75 - 100 DR/SD
Cause
Solution
The machine stops, as the The pressure exceeds the pressure safety switch has alarm pressure. tripped (red LED).
Check the line pressure, release the pressure to take it back to the set working values.
The machine fails to start when starting it up for the first time. Rotation alarm (red LED).
The screw unit and the motor of the radiator fan run in the opposite direction (for DR versions).
Invert two phases of the power supply on switch IG.
The motor of the radiator fan runs in the opposite direction (for SD versions).
Invert two phases of the power supply on switch IG.
Maintenance alarm (red The preset maintenance time flashing LED) has expired.
Follow the instructions given herein in Point 6.1.
The oil level is too high, suction valve faulty.
Drain the oil until the correct level is restored, contact an authorised Service centre for the valve.
The machine fails to depressurise during idle running mode, the oil separator cartridge is clogged.
Contact the Service centre.
Oil not suitable for the use of the compressor, air-oil separator cartridge torn. The screws of the cover of the oil separator tank are loose, oil level too high.
Replace the oil with one suitable for the type of use. Replace the cartridge of the oil separator, tighten the screws of the cover of the oil separator, and restore the correct oil level.
Oil leak from air filter.
Safety relief valve.
Excessive oil consumption.
40/50
AIRBLOK 75 - 100 DR/SD
7
Drawings and diagrams
7.1
Wiring diagrams
DRAWINGS AND DIAGRAMS
KEY OF THE WIRING DIAGRAMS (versions DR) QS: FUV:
Main ON/OFF switch Fan motor fuses 10.3x38 : aM 6A (100HP 400V) Fan motor fuses 10.3x38 : aM 4A (75HP 400V) Fan motor fuses 10.3x38 : aM 10A (100HP 230V) Fan motor fuses 10.3x38 : aM 8A (75HP 230V) MV: Fan motor MC: Compressor motor KR: Fan motor phases sequence relay F1-F2: Fuses 5x20 1A (T) F3: Fuse 5x20 1A (F) F4: Fuse 5x20 800mA (T) T: Transformer K1: Compressor motor line contact maker K2: Compressor motor delta contact maker K3: Compressor motor star contact maker K4: Fan motor contact maker R1-R2-R3: Voltage restrictors (excluding 75HP at 400V 50/60Hz) D: ECU Y1-Y2: Solenoid valve Y3-KTS: Condensate discharge solenoid valve SE: Emergency push button SR: Oil alarm reset button SA: Air filter vacuum gauge STV: Fan motor internal protection trip switch SD: Oil separator tank pressure switch BP: Pressure sensor BT: Temperature sensor RT: Compressor motor thermistors
41/50
7
GB
GB
7
DRAWINGS AND DIAGRAMS
AIRBLOK 75 - 100 DR/SD
42/50
AIRBLOK 75 - 100 DR/SD
DRAWINGS AND DIAGRAMS
43/50
7
GB
GB
7
DRAWINGS AND DIAGRAMS
AIRBLOK 75 - 100 DR/SD
KEY OF THE WIRING DIAGRAMS (versions SD) QS: FU: KG: U: FUV: KV: MV: MC: KR: F1-F2: F3: F4: F5: T: SE: MVA: C: D: Y1-Y2: Y3-KTS: SR: SD: SA: STV: BP: BT: RT:
Main ON/OFF switch Fuses NH1 400A ultra rapid 660V (100HP) Fuses NH000 200A ultra rapid 660V (75HP) Main contact maker Inverter Fan motor fuses 10.3x38 : aM 6A (100HP) Fan motor fuses 10.3x38 : aM 4A (75HP) Fan motor contact maker Fan motor Compressor motor Fan motor phases sequence relay Fuses 5x20 1A (T) Fuse 5x20 1A (F) Fuse 5x20 800mA (T) Fuse 5x20 500mA (T) Transformer Emergency button Electric control panel fan motor Electric control panel fan motor condenser ECU Solenoid valve Condensate discharge solenoid valve Oil separator button Oil separator pressure switch Air filter vacuum gauge Fan motor internal protection trip switch Pressure sensor Temperature sensor Compressor motor thermistors
44/50
AIRBLOK 75 - 100 DR/SD
DRAWINGS AND DIAGRAMS
45/50
7
GB
air delivery to radiator battery
idle running and adjustment valve pilot circuit
oil priming circuit
oil by pass circuit
oil recovery circuit
oil injection circuit
2
3
4
5
6
7
Oil drainage tap
11
oil air mix delivery circuit
Oil level indicator
10
1
Oil separator tank
9
RADIATOR BATTERY UNIT
Separator filter
8
D
Safety valve
7
OIL SEPARATOR UNIT
Gauge
6
C
Minimum valve
5
COMPRESSOR UNIT
Air radiator
4
B
Pressure switch
3
ADJUSTMENT VALVE UNIT
Silencer
2
Adjustment valve Idle running choker Solenoid valve (only for V100)
21 22 23
Direct transmission
19 Screw compressor unit
Electric motor
18
20
Cooling fan
Machine temperature probe
16 17
Oil radiator
15
Oil filter
Thermostatic valve
13 14
Thermostatic bulb
12
7.2
7
A
Air filter
1
GB DRAWINGS AND DIAGRAMS AIRBLOK 75 - 100 DR/SD
Pneumatic diagrams
46/50
AIRBLOK 75 - 100 DR/SD
DRAWINGS AND DIAGRAMS
47/50
7
GB
CODE CODICE
7385770000 7385900000 7030490000 7030730000 7012640000 7010530000 7030610000 7030600000 5070380008 7020140000 7010540000 5167050008 7020070000 7014470000 7580220000 7456270000 7010560000 7423210000 7423220000 7423130000 7423130000 7085940000 4112070000 7079690000 7564020000 7161700000 7030730000 7030490000 7012640000 7071350000 4094170000 7082600000 7043210000 7232370000 7212240000 7212050010 5167060008 7192620000 7081760000 7030930000 7024200000 7030490000 7030730000 7030020000 7030130000 7011290000 7470630000 7079560000 7211410000 7192610000
REF. RIF.
1 1A 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 17A 17B 17C 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
1 1 4 4 4 8 8 8 1 8 1 1 2 2 1 1 4 1 1 1 1 1 1 1 1 1 4 4 4 1 1 1 1 1 1 1 1 1 1 1 8 8 8 2 2 2 1 1 1 1
QT QT
Electric motor compressor - Motore elettrico compressore 380÷415V 50Hz Electric motor compressor - Motore elettrico compressore 380÷415V 60Hz Toothed washer - Rondella dentata Ø16 Washer - Rondella Ø16 Screw - Vite M16x50 Screw - Vite M18x70 Washer - Rondella Ø18 Toothed washer - Rondella dentata Ø18 Bell - Campana di fissaggio motore/vite Nut - Dado M18 Eyebolt - Golfare M24 Wire screen - Rete di protezione Nut - Dado M8 Grub screw - Grano M8 Joint - Giunto Delivery flange - Flangia di mandata Screw - Vite M16x90 Air end - Vite completa SCA14G (8bar 50Hz) Air end - Vite completa SCA14G (10bar 50Hz) Air end - Vite completa SCA14G (8bar 60Hz) Air end - Vite completa SCA14G (10bar 60Hz) Joint - Riduzione Sensor - Sensore temperatura Gasket - Guarnizione Sensor - Sensore intasamento Suction valve - Valvola di aspirazione Washer - Rondella Toothed washer - Rondella dentata Screw - Vite Oil seal kit (See kit assembling table) - Kit paraolio (Vedi tavola assemblaggio kit) Brearings and oil seal kit (See kit assembling table) - Kit cuscinetti e paraolio (Vedi tavola assemblaggio kit) Suction valve maintenance kit (See kit assembling table) - Kit manutenzione valvola aspirazione (Vedi tavola assemblaggio kit) Clamp - Fascetta Hose - Tubo Air filter - Filtro aria Air filter cartridge - Cartuccia filtro aria Support - Staffa Minimum pressure valve - Valvola di minima pressione Joint - Nipplo Washer - Rondella Nut - Dado M16 Toothed washer - Rondella dentata Ø16 Washer - Rondella Ø16 Washer - Rondella Toothed washer - Rondella dentata Screw - Vite Separator tank - Serbatoio separatore Gasket - Guarnizione Separator filter - Filtro separatore Safety valve - Valvola di sicurezza
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.03.L.04)
CODE CODICE
7250700000 7014350000 7056260010 7011160000 7231920000 7030390000 7180140000 7562600000 7090060000 5166790008 7011160000 7030360000 7020080000 7020060000 7012290000 7239010000 7231240000 7231940000 7231930000 7030580000 7081011300 7081530000 7211430000 7212430000 7030930000 7081520000 7011040000 7030020000 7062900000 7062890000 7070380000 7070390000
REF. RIF.
47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 75A 76 77
1 8 1 4 1 2 1 1 1 1 4 4 4 2 4 1 1 1 1 4 4 2 1 1 2 2 4 4 1 1 1 1
QT QT
DESCRIPTION DESCRIZIONE
8 BAR SCA14G 10 BAR SCA14G
Pressure switch - Pressostato intasamento filtro disoleatore Screw -Vite S.T.E.I. M16x70 Joint - Raccordo Screw - Vite Hose - Tubo di mandata Washer - Rondella Oil level sight glass - Spia livello olio Relief valve - Valvola di scarico Oil plug - Tappo olio Support - Supporto filtro olio Screw - Vite Toothed washer - Rondella dentata Washer - Rondella Nut - Dado Screw - Vite Hose - Tubo disoleatore/radiatore Hose - Tubo olio radiatore/filtro Hose - Tubo mandata aria Hose - Tubo iniezione Washer - Rondella Joint - Raccordo Joint - Raccordo Oil filter - Filtro olio Support - Supporto filtro olio Washer - Rondella Joint - Raccordo Screw - Vite Washer - Rondella Spacer - Distanziale Spacer - Distanziale (10bar 60Hz) OR gasket - Guarnizione OR OR gasket - Guarnizione OR
AIRBLOK75 DR AIRBLOK75 DR
1/4 1/4
AIRBLOK75 DR SCA14G
1/4
CODE CODICE
7014420000 7012240000 7014140000 7018590000 7459920000 7459920020 7519530000 5166800008 7280110000 5011980008 5166670008 5166660008 5166830008 5166730008 5166820008 7155500000 5166840008 5166810008 5166720008 5166680008 5166690008 5166700008 5166710008 5166850008 5167090008 7212240000 7012300000 7031030000 7012300000 7300080000 7014420000 7433220000 5011950008
REF. RIF.
100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132
16 98 24 6 4 1 1 1 2 4 2 2 3 3 1 1 1 1 1 1 1 1 1 1 2 1 16 16 8 1 4 1 1
QT QT
Screw - Vite Screw - Vite Screw - Vite Hinge - Cerniera Key hole - Serratura Key - Chiave Oil level panel - Pannello spia olio Panel - Pannello Handle - Maniglia Support - Supporto montanti Angular - Angolare Angular - Angolare Panel - Pannello Column - Montante Rear panel - Pannello posteriore Electronic card panel - Pannello scheda elettronica Panel - Pannello Central panel - Pannello centrale Column - Montante Column - Montante Column - Montante Column - Montante Column - Montante Pre-filter panel - Pannello prefiltro Angular - Angolare prefiltro Pre-filter - Prefiltro Screw - Vite Washer - Rondella Screw - Vite Emergency push-button - Pulsante di emergenza Screw - Vite Electronic card - Scheda elettronica Base - Basamento
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.03.L.04)
REF. RIF.
CODE CODICE
QT QT
AIRBLOK75 DR AIRBLOK75 DR DESCRIPTION DESCRIZIONE
8 BAR SCA14G 10 BAR SCA14G
2/4 2/4
AIRBLOK75 DR SCA14G
2/4
CODE CODICE
7507480000 7020060000 7030020000 7018690000 7030020000 7201360000 7201420000 7200360000 7030130000 7011050000 5166930008 7030020000 5167030008 7012240000 5166950008 5167260008 5166750008 5166740008 5166760008 5166780008 5166880008 5166890008 5166910008 7014140000 7018590000 7011040000 5166990008 5167270008 7459920020 7433370000 5166870008 5166770008 7014450000 5166920008 5166970008 7248090000 5167010008
REF. RIF.
200 201 202 203 204 205 205A 205B 206 207 208 209 210 211 212 212A 213 214 215 216 217 218 219 220 221 222 223 223A 224 225 226 227 228 229 230 231 232
1 6 10 2 12 1 1 1 6 26 1 10 1 26 1 1 1 2 1 1 1 1 1 8 4 16 1 1 2 1 1 1 8 1 2 1 1
QT QT
Radiator - Radiatore Nut - Dado Washer - Rondella Eyebolt - Golfare M10 Washer - Rondella Fan - Ventola radiale V230-V400 / 50Hz Fan - Ventola radiale V400 / 60Hz Fan - Ventola radiale V460 / 60Hz Toothed washer - Rondella dentata Screw - Vite Plate - Piastra Washer - Rondella Ø6 Cover - Coperchio laterale Screw - Vite Fan box - Box ventola Fan box - Box ventola V400-v460 / 60Hz Support - Angolare Support - Angolare superiore Support - Angolare Support - Angolare superiore di irrigidimento Panel - Pannello superiore Panel - Pannello radiatore Panel - Pannello Screw - Vite Hinge - Cerniera Screw - Vite Support - Supporto Support - Supporto V400-V460 / 60Hz Key hole - Serratura Handle - Maniglia blocca porta Panel - Pannello Support - Angolare Screw - Vite M5x50 Electric box - Cassetta elettrica Support - Supporto Grille - Griglia Grille - Griglia
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.03.L.04)
REF. RIF.
CODE CODICE
QT QT
AIRBLOK75 DR AIRBLOK75 DR DESCRIPTION DESCRIZIONE
8 BAR SCA14G 10 BAR SCA14G
3/4 3/4
AIRBLOK75 DR SCA14G
3/4
CODE CODICE
7413700000 7509290000 7081130000 7030030000 7031010000 7020070000 7433450000 7084270000 7300230000 7432310000 7432720000 7432720000 7431630000 7433290000 7432750000 7432400000 7432400000 7433330000 7564260000 7432260000 7433030000 7082050000 7082640000 7083110000 7080180000 5167100008 7012240000 7084950000 7080800000 7562980000 7081160000 7191010000 7082300000 7194330000 7080780000 7230070000 7564330000 7082570000 7194340000 7085600000 7081010000 7500570000 5165700008 7080810000 7080810000 7500440000 7011030000 7012240000 5166940008 4086450000
REF. RIF.
300 301 302 303 304 305 306 307 308 309 310 310A 310B 310C 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346
1 1 4 4 4 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 2 8 3 3 3 6 1 1 1 1 1 1 1 4 1 3 1 1 1 2 2 6 1 1
QT QT
Electric board - Apparecchiatura elettrica V400 50/60Hz Electric board plate - Piastra impianto elettrico Screw - Vite M8x40 Washer - Rondella Toothed washer - Rondella dentata Nut - Dado M8 Blocking door - Bloccaporte Joint - Raccordo 1/8" RESET push-button - Pulsante di RESET Contactor - Contattore A50 (K3) Fuse - Fusibile 1A ritardato Fuse - Fusibile 1A ritardato Fuse - Fusibile 1A ritardato Fuse - Fusibile 800mA ritardato Connector - Morsettiera Contactor - Contattore A75 (K2) Contactor - Contattore A75 (K1) Fuse - Fusibile 1A Transormer - Trasformatore 160VA (T) Contactor - Contattore A9 (K4) Relay - Rele sequenza fasi (KR) Joint - Raccordo "T" 1/4" Joint - Raccordo "L" 1/8" Joint - Raccordo "T" 1/8" Joint - Raccordo Support - Supporto filtri Screw - Vite Joint - Raccordo "L" 1/8" Ø10 Joint - Raccordo "L" 1/8" Ø6 Filter - Filtro condensa Joint - Raccordo Valve - Valvola unidirezionale Joint - Raccordo "T" 1/8" Ø6 Solenoid valve - Elettrovalvola Joint - Raccordo "L" 1/8" Ø6 Rilsan FLUORFLON hose - Tubo Rilsan FLUORFLON Ø10 Pressure transducer - Trasduttore di pressione Joint - Raccordo diritto 1/8" Ø6 calzamento Solenoid valve - Elettrovalvola Joint - Raccordo Joint - Raccordo 1/2" Stretch eleminator - Pressacavo M63x1,5 Support - Supporto Joint - Raccordo "L" 1/4" Ø6 Joint - Raccordo Stretch eleminator - Pressacavo M20x1,5 Screw - Vite TE M6x10 Screw - Vite Support - Supporto Solenoid valve - Elettrovalvola
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.03.L.04)
CODE CODICE
7230050000 7082980000 7082300000 7500430000 6002580012
REF. RIF.
347 348 349 350 351
1 1 1 8 1
QT QT
DESCRIPTION DESCRIZIONE
8 BAR SCA14G 10 BAR SCA14G
Rilsan FLUORFLON hose - Tubo Rilsan FLUORFLON Ø6 Joint - Raccordo diritto 1/4" Joint - Raccordo Stretch eleminator - Pressacavo M16x1,5 Joint - Raccordo "T" 1/2"
AIRBLOK75 DR AIRBLOK75 DR
4/4 4/4
AIRBLOK75 DR SCA14G
4/4
CODE CODICE
7385780000 7385890000 7030490000 7030730000 7012640000 7010530000 7030610000 7030600000 5070380008 7020140000 7010540000 5167050008 7020070000 7014470000 7580230000 7456270000 7010560000 7423240000 7423200000 7423190000 7423210000 7085940000 4112070000 7079690000 7564020000 7161700000 7030730000 7030490000 7012640000 4094520000 4094530000 7082600000 7043210000 7232370000 7212240000 7212240010 5167060008 7192620000 7081760000 7030930000 7024200000 7030490000 7030730000 7030020000 7030130000 7011290000 7470630000 7079560000 7212170000 7192610000
REF. RIF.
1 1A 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 17A 17B 17C 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
1 1 4 4 4 8 8 8 1 8 1 1 2 2 1 1 4 1 1 1 1 1 1 1 1 1 4 4 4 1 1 1 1 1 1 1 1 1 1 1 8 8 8 2 2 2 1 1 1 1
QT QT
Electric motor 400V compressor - Motore elettrico compressore 400V 50Hz Electric motor 400V compressor - Motore elettrico compressore 400V 60Hz Toothed washer - Rondella dentata Ø16 Washer - Rondella Ø16 Screw - Vite M16x50 Screw - Vite M18x70 Washer - Rondella Ø18 Toothed washer - Rondella dentata Ø18 Bell - Campana di fissaggio motore/vite Nut - Dado M18 Eyebolt - Golfare M24 Wire screen - Rete di protezione Nut - Dado M8 Grub screw - Grano M8 Joint - Giunto Delivery flange - Flangia di mandata Screw - Vite M16x90 Air end - Vite completa SCA14G (8bar 50Hz) Air end - Vite completa SCA14G (10bar 50Hz) Air end - Vite completa SCA14G (8bar 60Hz) Air end - Vite completa SCA14G (10bar 60Hz) Joint - Riduzione Sensor - Sensore temperatura Gasket - Guarnizione Sensor - Sensore intasamento Suction valve - Valvola di aspirazione Washer - Rondella Toothed washer - Rondella dentata Screw - Vite Oil seal kit (See kit assembling table) - Kit paraolio (Vedi tavola assemblaggio kit) Brearings and oil seal kit (See kit assembling table) - Kit cuscinetti e paraolio (Vedi tavola assemblaggio kit) Suction valve maintenance kit (See kit assembling table) - Kit manutenzione valvola aspirazione (Vedi tavola assemblaggio kit) Clamp - Fascetta Hose - Tubo Air filter - Filtro aria Air filter cartridge - Cartuccia filtro aria Support - Staffa Minimum pressure valve - Valvola di minima pressione Joint - Nipplo Washer - Rondella Nut - Dado M16 Toothed washer - Rondella dentata Ø16 Washer - Rondella Ø16 Washer - Rondella Toothed washer - Rondella dentata Screw - Vite Separator tank - Serbatoio separatore Gasket - Guarnizione Separator filter - Filtro separatore Safety valve - Valvola di sicurezza
DESCRIPTION DESCRIZIONE
VALID FROM 18/11/2004 - VALIDO DAL 18/11/2004 (REV.04.M.04)
CODE CODICE
7250710000 7014350000 7056260010 7011160000 7231920000 7030390000 7180140000 7562600000 7090060000 5166790008 7011160000 7030360000 7020080000 7020060000 7012290000 7239010000 7231240000 7231940000 7231930000 7030580000 7081011300 7081530000 7212430000 7211430000 7030930000 7081520000 7011040000 7030020000 7062910000 7070380000 7070390000
REF. RIF.
47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77
1 8 1 4 1 2 1 1 1 1 4 4 4 2 4 1 1 1 1 4 4 2 1 1 2 2 4 4 1 1 1
QT QT
DESCRIPTION DESCRIZIONE
8 BAR 10 BAR
SCA14G SCA14G
Pressure switch - Pressostato intasamento filtro disoleatore Screw -Vite S.T.E.I. M16x70 Joint - Raccordo Screw - Vite Hose - Tubo di mandata Washer - Rondella Oil level sight glass - Spia livello olio Relief valve - Valvola di scarico Oil plug - Tappo olio Support - Supporto filtro olio Screw - Vite Toothed washer - Rondella dentata Washer - Rondella Nut - Dado Screw - Vite Hose - Tubo disoleatore/radiatore Hose - Tubo olio radiatore/filtro Hose - Tubo mandata aria Hose - Tubo iniezione Washer - Rondella Joint - Raccordo Joint - Raccordo Support - Supporto filtro olio Oil filter - Filtro olio Washer - Rondella Joint - Raccordo Screw - Vite Washer - Rondella Spacer - Distanziale OR gasket - Guarnizione OR OR gasket - Guarnizione OR
AIRBLOK100 DR AIRBLOK100 DR
1/4 1/4
AIRBLOK100 DR
SCA14G
1/4
CODE CODICE
7014420000 7012240000 7014140000 7018590000 7459920000 7459920020 7519530000 5166800008 7280110000 5011980008 5166670008 5166660008 5166830008 5166730008 5166820008 7155500000 5166840008 5166810008 5166720008 5166680008 5166690008 5166700008 5166710008 5166850008 5167090008 7212240000 7012300000 7031030000 7012300000 7300080000 7014420000 7433220000 5011950008
REF. RIF.
100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132
16 98 24 6 4 1 1 1 2 4 2 2 3 3 1 1 1 1 1 1 1 1 1 1 2 1 16 16 8 1 4 1 1
QT QT
Screw - Vite Screw - Vite Screw - Vite Hinge - Cerniera Key hole - Serratura Key - Chiave Oil level panel - Pannello spia olio Panel - Pannello Handle - Maniglia Support - Supporto montanti Angular - Angolare Angular - Angolare Panel - Pannello Column - Montante Rear panel - Pannello posteriore Electronic card panel - Pannello scheda elettronica Panel - Pannello Central panel - Pannello centrale Column - Montante Column - Montante Column - Montante Column - Montante Column - Montante Pre-filter panel - Pannello prefiltro Angular - Angolare prefiltro Pre-filter - Prefiltro Screw - Vite Washer - Rondella Screw - Vite Emergency push-button - Pulsante di emergenza Screw - Vite Electronic card - Scheda elettronica Base - Basamento
DESCRIPTION DESCRIZIONE
VALID FROM 18/11/2004 - VALIDO DAL 18/11/2004 (REV.04.M.04)
REF. RIF.
CODE CODICE
QT QT
DESCRIPTION DESCRIZIONE
AIRBLOK100 DR 8 BAR AIRBLOK100 DR 10 BAR
SCA14G SCA14G
2/4 2/4
AIRBLOK100 DR
SCA14G
2/4
CODE CODICE
7507480000 7020060000 7030020000 7018690000 7030020000 7201360000 7201420000 7200360000 7030130000 7011050000 5166930008 7030020000 5167030008 7012240000 5166950008 5167260008 5166750008 5166740008 5166760008 5166780008 5166880008 5166890008 5166910008 7014140000 7018590000 7011040000 5166990008 5167270008 7459920020 7433370000 5166870008 5166770008 7014450000 5166920008 5166970008 7248090000 5167010008
REF. RIF.
200 201 202 203 204 205 205A 205B 206 207 208 209 210 211 212 212A 213 214 215 216 217 218 219 220 221 222 223 223A 224 225 226 227 228 229 230 231 232
1 6 10 2 12 1 1 1 6 26 1 10 1 26 1 1 1 2 1 1 1 1 1 8 4 16 1 1 2 1 1 1 8 1 2 1 1
QT QT
Radiator - Radiatore Nut - Dado Washer - Rondella Eyebolt - Golfare M10 Washer - Rondella Fan - Ventola radiale V230-V400 / 50Hz Fan - Ventola radiale V400 / 60Hz Fan - Ventola radiale V460 / 60Hz Toothed washer - Rondella dentata Screw - Vite Plate - Piastra Washer - Rondella Ø6 Cover - Coperchio laterale Screw - Vite Fan box - Box ventola Fan box - Box ventola V400-v460 / 60Hz Support - Angolare Support - Angolare superiore Support - Angolare Support - Angolare superiore di irrigidimento Panel - Pannello superiore Panel - Pannello radiatore Panel - Pannello Screw - Vite Hinge - Cerniera Screw - Vite Support - Supporto Support - Supporto V400-V460 / 60Hz Key hole - Serratura Handle - Maniglia blocca porta Panel - Pannello Support - Angolare Screw - Vite M5x50 Electric box - Cassetta elettrica Support - Supporto Grille - Griglia Grille - Griglia
DESCRIPTION DESCRIZIONE
VALID FROM 18/11/2004 - VALIDO DAL 18/11/2004 (REV.04.M.04)
REF. RIF.
CODE CODICE
QT QT
DESCRIPTION DESCRIZIONE
AIRBLOK100 DR 8 BAR AIRBLOK100 DR 10 BAR
SCA14G SCA14G
3/4 3/4
AIRBLOK100 DR
SCA14G
3/4
CODE CODICE
7413710000 7509290000 7081130000 7030030000 7031010000 7020070000 7433450000 7084270000 7300230000 7432400000 7432780000 7432720000 7431640000 7433290000 7432750000 7432410000 7432410000 7433340000 7564260000 7432260000 7433030000 7082850000 7082640000 7083110000 7080180000 5167100008 7012240000 7084950000 7080800000 7562980000 7081160000 7191010000 7082300000 7194330000 7080780000 7230070000 7564330000 7082590000 7194340000 7085600000 7081010000 7500570000 5165700008 7080810000 7080810000 7500440000 7011030000 7012240000 5166940008 4086450000
REF. RIF.
300 301 302 303 304 305 306 307 308 309 310 310A 310B 310C 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346
1 1 4 4 4 4 1 2 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 3 1 1 2 7 3 3 3 6 1 1 2 1 1 4 1 2 1 3 1 1 1 2 2 6 1 1
QT QT
Electric board - Apparecchiatura elettrica V400 50/60Hz Electric board plate - Piastra impianto elettrico Screw - Vite M8x40 Washer - Rondella Toothed washer - Rondella dentata Nut - Dado M8 Blocking door - Bloccaporte Joint - Raccordo 1/8" RESET push-button - Pulsante di RESET Contactor - Contattore A76 (K3) Fuse - Fusibile 1A ritardato Fuse - Fusibile 1A ritardato Fuse - Fusibile 1A ritardato Fuse - Fusibile 800mA ritardato Connector - Morsettiera Contactor - Contattore A95 (K2) Contactor - Contattore A95 (K1) Fuse - Fusibile 6A Transformer - Trasformatore (T) Contactor - Contattore A9 (K4) Relay - Rele sequenza fasi (KR) Joint - Raccordo "T" 1/4" Joint - Raccordo "L" 1/8" Joint - Raccordo "T" 1/8" Joint - Raccordo Support - Supporto filtri Screw - Vite Joint - Raccordo "L" 1/8" Ø10 Joint - Raccordo "L" 1/8" Ø6 Filter - Filtro condensa Joint - Raccordo Valve - Valvola unidirezionale Joint - Raccordo "T" 1/8" Ø6 Solenoid valve - Elettrovalvola Joint - Raccordo "L" 1/8" Ø6 Rilsan FLUORFLON hose - Tubo Rilsan FLUORFLON Ø10 Pressure transducer - Trasduttore di pressione Joint - Raccordo diritto 1/8" Ø6 Solenoid valve - Elettrovalvola Joint - Raccordo Joint - Raccordo 1/2" Stretch eleminator - Pressacavo M63x1,5 Support - Supporto Joint - Raccordo "L" 1/4" Ø6 Joint - Raccordo Stretch eleminator - Pressacavo M20x1,5 Screw - Vite TE M6x10 Screw - Vite Support - Supporto Solenoid valve - Elettrovalvola
DESCRIPTION DESCRIZIONE
VALID FROM 18/11/2004 - VALIDO DAL 18/11/2004 (REV.04.M.04)
CODE CODICE
7230050000 7082980000 7082300000 7500430000 6002580012
REF. RIF.
347 348 349 350 351
1 1 1 8 1
QT QT
SCA14G SCA14G
Rilsan FLUORFLON hose - Tubo Rilsan FLUORFLON Ø6 Joint - Raccordo diritto 1/4" Joint - Raccordo Stretch eleminator - Pressacavo M16x1,5 Joint - Raccordo "T" 1/2"
DESCRIPTION DESCRIZIONE
AIRBLOK100 DR 8 BAR AIRBLOK100 DR 10 BAR
4/4 4/4
AIRBLOK100 DR
SCA14G
4/4
CODE CODICE
7385770000 7030490000 7030730000 7012640000 7010530000 7030610000 7030600000 5070370008 7020140000 7010540000 5167050008 7020070000 7014470000 7580220000 7456270000 7010560000 7423130000 7085940000 4112070000 7079690000 7564020000 7161700000 7030730000 7030490000 7012640000 7071350000 4094170000 7082600000 7043210000 7232370000 7212240000 7212050010 5167060008 7192620000 7081760000 7030930000 7024200000 7030490000 7030730000 7030020000 7030130000 7011290000 7470630000 7079560000 7211410000 7192610000 7250700000 7014350000 7056260010 7011160000
REF. RIF.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
1 4 4 4 8 8 8 1 8 1 1 2 2 1 1 4 1 1 1 1 1 1 4 4 4 1 1 1 1 1 1 1 1 1 1 1 8 8 8 2 2 2 1 1 1 1 1 8 1 4
QT QT
Electric motor 400V compressor - Motore elettrico compressore 400V Toothed washer - Rondella dentata Ø16 Washer - Rondella Ø16 Screw - Vite M16x50 Screw - Vite M18x70 Washer - Rondella Ø18 Toothed washer - Rondella dentata Ø18 Bell - Campana di fissaggio motore/vite Nut - Dado M18 Eyebolt - Golfare M24 Wire screen - Rete di protezione Nut - Dado M8 Grub screw - Grano M8 Joint - Giunto Delivery flange - Flangia di mandata Screw - Vite M16x90 Air end - Vite completa SCA14 Joint - Riduzione Sensor - Sensore temperatura Gasket - Guarnizione Sensor - Sensore intasamento Suction valve - Valvola di aspirazione Washer - Rondella Toothed washer - Rondella dentata Screw - Vite Oil seal kit (See kit assembling table) - Kit paraolio (Vedi tavola assemblaggio kit) Brearings and oil seal kit (See kit assembling table) - Kit cuscinetti e paraolio (Vedi tavola assemblaggio kit) Suction valve maintenance kit (See kit assembling table) - Kit manutenzione valvola aspirazione (Vedi tavola assemblaggio kit) Clamp - Fascetta Hose - Tubo Air filter - Filtro aria Air filter cartridge - Cartuccia filtro aria Support - Staffa Minimum pressure valve - Valvola di minima pressione Joint - Nipplo Washer - Rondella Nut - Dado M16 Toothed washer - Rondella dentata Ø16 Washer - Rondella Ø16 Washer - Rondella Toothed washer - Rondella dentata Screw - Vite Separator tank - Serbatoio separatore Gasket - Guarnizione Separator filter - Filtro separatore Safety valve - Valvola di sicurezza Pressure switch - Pressostato intasamento filtro disoleatore Screw -Vite S.T.E.I. M16x70 Joint - Raccordo Screw - Vite
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.04.L.04)
CODE CODICE
7231920000 7030390000 7180140000 7562600000 7090060000 5166790008 7011160000 7030360000 7020080000 7020060000 7012290000 7239010000 7231240000 7231940000 7231930000 7030580000 7081011300 7081530000 7211430000 7212430000 7030930000 7081520000 7011040000 7030020000 7062890000 7070380000 7070390000 7082050000 7111010000 7500570000 7500440000
REF. RIF.
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81
1 2 1 1 1 1 4 4 4 2 4 1 1 1 1 4 4 2 1 1 2 2 4 4 1 1 1 1 1 1 1
QT QT
Hose - Tubo di mandata Washer - Rondella Oil level sight glass - Spia livello olio Relief valve - Valvola di scarico Oil plug - Tappo olio Support - Supporto filtro olio Screw - Vite Toothed washer - Rondella dentata Washer - Rondella Nut - Dado Screw - Vite Hose - Tubo disoleatore/radiatore Hose - Tubo olio radiatore/filtro Hose - Tubo mandata aria Hose - Tubo iniezione Washer - Rondella Joint - Raccordo Joint - Raccordo Oil filter - Filtro olio Support - Supporto filtro olio Washer - Rondella Joint - Raccordo Screw - Vite Washer - Rondella Spacer - Distanziale OR gasket - Guarnizione OR OR gasket - Guarnizione OR Joint - Raccordo Pressure gauge - Manometro Stretch eliminator - Pressacavo Stretch eliminator - Pressacavo
DESCRIPTION DESCRIZIONE
AIRBLOK75 SD 8 BAR SCA14 1/4 AIRBLOK75 SD 10 BAR SCA14 1/4
AIRBLOK75 SD SCA14 1/4
CODE CODICE
7014420000 7012240000 7014140000 7018590000 7459920000 7459920020 7519530000 5166800008 7280110000 5011980008 5166670008 5166660008 5166830008 5166730008 5166820008 7155500000 5166840008 5166810008 5166720008 5166680008 5166690008 5166700008 5166710008 5166850008 5167090008 7212240000 7012300000 7031030000 7012300000 7300080000 7014420000 7433220000 5011950008
REF. RIF.
100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132
16 98 24 6 4 1 1 1 2 4 2 2 3 3 1 1 1 1 1 1 1 1 1 1 2 1 16 16 8 1 4 1 1
QT QT
Screw - Vite Screw - Vite Screw - Vite Hinge - Cerniera Key hole - Serratura Key - Chiave Oil level panel - Pannello spia olio Panel - Pannello Handle - Maniglia Support - Supporto montanti Angular - Angolare Angular - Angolare Panel - Pannello Column - Montante Rear panel - Pannello posteriore Electronic card panel - Pannello scheda elettronica Panel - Pannello Central panel - Pannello centrale Column - Montante Column - Montante Column - Montante Column - Montante Column - Montante Pre-filter panel - Pannello prefiltro Angular - Angolare prefiltro Pre-filter - Prefiltro Screw - Vite Washer - Rondella Screw - Vite Emergency push-button - Pulsante di emergenza Screw - Vite Electronic card - Scheda elettronica Base - Basamento
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.04.L.04)
REF. RIF.
CODE CODICE
QT QT
DESCRIPTION DESCRIZIONE
AIRBLOK75 SD 8 BAR SCA14 2/4 AIRBLOK75 SD 10 BAR SCA14 2/4
AIRBLOK75 SD SCA14 2/4
CODE CODICE
7507480000 7020060000 7030020000 7018690000 7030020000 7201360000 7201420000 7200360000 7030130000 7011050000 7201400000 7030020000 5167030008 7012240000 5166950008 5167260008 5166750008 5166740008 5166760008 5166780008 5166880008 5166890008 5166900008 7014140000 7018590000 7011040000 7212420000 7459920020 7433370000 5166860008 5166770008 7014450000 5166920008 7212410000 7212410010 7212420010 5166990008 5167270008 5166970008 7248090000 5167010008 7500440000
REF. RIF.
200 201 202 203 204 205 205A 205B 206 207 208 209 210 211 212 212A 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 233A 234 235 236 237
1 6 10 2 12 1 1 1 6 26 1 10 1 26 1 1 1 2 1 1 1 1 1 8 4 16 2 2 1 1 1 8 1 1 1 2 1 1 2 1 1 1
QT QT
Radiator - Radiatore Nut - Dado Washer - Rondella Eyebolt - Golfare M10 Washer - Rondella Fan - Ventola radiale V230-V400 / 50Hz Fan - Ventola radiale V400 / 60Hz Fan - Ventola radiale V460 / 60Hz Toothed washer - Rondella dentata Screw - Vite Fan - Ventola V230/50-60Hz Washer - Rondella Ø6 Cover - Coperchio laterale Screw - Vite Fan box - Box ventola Fan box - Box ventola V400-460 / 60Hz Support - Angolare Support - Angolare superiore Support - Angolare Support - Angolare superiore di irrigidimento Panel - Pannello superiore Panel - Pannello radiatore Panel - Pannello Screw - Vite Hinge - Cerniera Screw - Vite Electric fan filter - Filtro elettroventola Key hole - Serratura Handle - Maniglia blocca porta Panel - Pannello Support - Angolare Screw - Vite M5x50 Electric box - Cassetta elettrica Electric fan filter - Filtro elettroventola completo Filter - Filtro Filter - Filtro Support - Supporto Support - Supporto V400-460 / 60Hz Support - Supporto Grille - Griglia Grille - Griglia Stretch eliminator - Pressacavo M20x1,5
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.04.L.04)
REF. RIF.
CODE CODICE
QT QT
DESCRIPTION DESCRIZIONE
AIRBLOK75 SD 8 BAR SCA14 3/4 AIRBLOK75 SD 10 BAR SCA14 3/4
AIRBLOK75 SD SCA14 3/4
7413680000 7413800000 7509290000 7081130000 7030030000 7031010000 7020070000 7433350000 7084270000 7300230000 7433390000 7194330000
300 300A 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 315A 316 316A 317 317A 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345
7080780000 7230070000 7564330000 7082570000 7194340000 7085600000 7081010000 7500570000 5165700008 7080810000 7080810000 7500440000 7011030000 7012240000 5166940008
7432260000 7432970000 7564340000 7564390000 7433330000 7436080000 7433310000 7436090000 7082050000 7082640000 7083110000 7084370000 5167100008 7012240000 7084750000 7080800000 7562980000 7081160000 7191010000 7082300000
CODE CODICE
REF. RIF.
1 1 1 4 4 4 4 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 2 4 1 1 1 1 1 3 1 2 1 3 1 1 1 2 2 6 1
QT QT
Electric board - Apparecchiatura elettrica V400 50/60Hz Electric board - Apparecchiatura elettrica V460 60Hz Electric board plate - Piastra impianto elettrico Screw - Vite M8x40 Washer - Rondella Toothed washer - Rondella dentata Nut - Dado M8 Blocking door - Bloccaporte Joint - Raccordo 1/8" RESET push-button - Pulsante di RESET Contactor - Contattore Solenoid valve - Elettrovalvola Fuse carrier - Base portafusibili Fuse carrier - Portafusibili ventola Fan contactor - Contattore ventola Inverter - Inverter Transformer - Trasformatore Transformer - Trasformatore V460 / 60Hz Fan fuse - Fusibile ventola Fan fuse - Fusibile ventola V460 / 60Hz Inverter fuse - Fusibile inverter Inverter fuse - Fusibile inverter V460 / 60Hz Joint - Raccordo "T" 1/4" Joint - Raccordo "L" 1/8" Joint - Raccordo "T" 1/8" Joint - Raccordo Support - Supporto filtri Screw - Vite Joint - Raccordo "L" Ø10 Joint - Raccordo "L" 1/8" Ø6 Filter - Filtro condensa Joint - Raccordo Valve - Valvola unidirezionale Joint - Raccordo "T" 1/8" Ø6 Connector - Morsetto Joint - Raccordo "L" 1/8" Ø6 Rilsan FLUORFLON hose - Tubo Rilsan FLUORFLON Ø10 Pressure transducer - Trasduttore di pressione Joint - Raccordo diritto 1/8" Ø6 Solenoid valve - Elettrovalvola Joint - Raccordo Joint - Raccordo Stretch eleminator - Pressacavo M63x1,5 Support - Supporto Joint - Raccordo "L" 1/4" Ø6 Joint - Raccordo Stretch eleminator - Pressacavo M20x1,5 Screw - Vite TE M6x10 Screw - Vite Support - Supporto
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.04.L.04)
CODE CODICE
4086450000 7230050000 7082980000 7082300000 7500430000 7433030000 7433190000 7436070000 7431640000 7080800000 7012280000
REF. RIF.
346 347 348 349 350 351 351A 352 353 354 355
1 1 1 1 8 1 1 1 1 1 2
QT QT
Solenoid valve - Elettrovalvola Rilsan FLUORFLON hose - Tubo Rilsan FLUORFLON Ø6 Joint - Raccordo diritto 1/4" Joint - Raccordo Stretch eleminator - Pressacavo M16x1,5 Relay - Rele sequenza fasi V400 / 50Hz Relay - Rele sequenza fasi V440-480 / 60Hz Fuse - Fusibile 500V 1A ritardato Fuse - Fusibile 1A rapido Joint - Raccordo Screw - Vite
DESCRIPTION DESCRIZIONE
AIRBLOK75 SD 8 BAR SCA14 4/4 AIRBLOK75 SD 10 BAR SCA14 4/4
AIRBLOK75 SD SCA14 4/4
CODE CODICE
7385780000 7030490000 7030730000 7012640000 7010530000 7030610000 7030600000 5070380008 7020140000 7010540000 5167050008 7020070000 7014470000 7580230000 7456270000 7010560000 7423190000 7085940000 4112070000 7079690000 7564020000 7161700000 7030730000 7030490000 7012640000 4094520000 4094530000 7082600000 7043210000 7232370000 7212240000 7212240010 5167060008 7192620000 7081760000 7030930000 7024200000 7030490000 7030730000 7030020000 7030130000 7011290000 7470630000 7079560000 7212170000 7192610000 7250700000 7014350000 7056260010 7011160000
REF. RIF.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
1 4 4 4 8 8 8 1 8 1 1 2 2 1 1 4 1 1 1 1 1 1 4 4 4 1 1 1 1 1 1 1 1 1 1 1 8 8 8 2 2 2 1 1 1 1 1 8 1 4
QT QT
Electric motor 380÷415V - 460V compressor - Motore elettrico compressore 380÷415V - 460V Toothed washer - Rondella dentata Ø16 Washer - Rondella Ø16 Screw - Vite M16x50 Screw - Vite M18x70 Washer - Rondella Ø18 Toothed washer - Rondella dentata Ø18 Bell - Campana di fissaggio motore/vite Nut - Dado M18 Eyebolt - Golfare M24 Wire screen - Rete di protezione Nut - Dado M8 Grub screw - Grano M8 Joint - Giunto Delivery flange - Flangia di mandata Screw - Vite M16x90 Air end - Vite completa SCA14G 53/37 Joint - Riduzione Sensor - Sensore temperatura Gasket - Guarnizione Sensor - Sensore intasamento Suction valve - Valvola di aspirazione Washer - Rondella Toothed washer - Rondella dentata Screw - Vite Oil seal kit (See kit assembling table) - Kit paraolio (Vedi tavola assemblaggio kit) Brearings and oil seal kit (See kit assembling table) - Kit cuscinetti e paraolio (Vedi tavola assemblaggio kit) Suction valve maintenance kit (See kit assembling table) - Kit manutenzione valvola aspirazione (Vedi tavola assemblaggio kit) Clamp - Fascetta Hose - Tubo Air filter - Filtro aria Air filter cartridge - Cartuccia filtro aria Support - Staffa Minimum pressure valve - Valvola di minima pressione Joint - Nipplo Washer - Rondella Nut - Dado M16 Toothed washer - Rondella dentata Ø16 Washer - Rondella Ø16 Washer - Rondella Toothed washer - Rondella dentata Screw - Vite Separator tank - Serbatoio separatore Gasket - Guarnizione Separator filter - Filtro separatore Safety valve - Valvola di sicurezza Pressure switch - Pressostato intasamento filtro disoleatore Screw -Vite S.T.E.I. M16x70 Joint - Raccordo Screw - Vite
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.03.L.04)
CODE CODICE
7231920000 7030390000 7180140000 7562600000 7090060000 5166790008 7011160000 7030360000 7020080000 7020060000 7012290000 7239010000 7231240000 7231940000 7231930000 7030580000 7081011300 7081530000 7212430000 7211430000 7030930000 7081520000 7011040000 7030020000 7062910000 7070380000 7070390000 7082050000 7111010000 7500570000 7500440000
REF. RIF.
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81
1 2 1 1 1 1 4 4 4 2 4 1 1 1 1 4 4 2 1 1 2 2 4 4 1 1 1 1 1 1 1
QT QT
Hose - Tubo di mandata Washer - Rondella Oil level sight glass - Spia livello olio Relief valve - Valvola di scarico Oil plug - Tappo olio Support - Supporto filtro olio Screw - Vite Toothed washer - Rondella dentata Washer - Rondella Nut - Dado Screw - Vite Hose - Tubo disoleatore/radiatore Hose - Tubo olio radiatore/filtro Hose - Tubo mandata aria Hose - Tubo iniezione Washer - Rondella Joint - Raccordo Joint - Raccordo Support - Supporto filtro olio Oil filter - Filtro olio Washer - Rondella Joint - Raccordo Screw - Vite Washer - Rondella Spacer - Distanziale OR gasket - Guarnizione OR OR gasket - Guarnizione OR Joint - Raccordo Pressure gauge - Manometro Stretch eliminator - Pressacavo M63x1,5 Stretch eliminator - Pressacavo M20x1,5
DESCRIPTION DESCRIZIONE
AIRBLOK100 SD 8 BAR AIRBLOK100 SD 10 BAR
SCA14G SCA14G
1/4 1/4
AIRBLOK100 SD SCA14G 1/4
CODE CODICE
7014420000 7012240000 7014140000 7018590000 7459920000 7459920020 7519530000 5166800008 7280110000 5011980008 5166670008 5166660008 5166830008 5166730008 5166820008 7155500000 5166840008 5166810008 5166720008 5166680008 5166690008 5166700008 5166710008 5166850008 5167090008 7212240000 7012300000 7031030000 7012300000 7300080000 7014420000 7433220000 5011950008
REF. RIF.
100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132
16 98 24 6 4 1 1 1 2 4 2 2 3 3 1 1 1 1 1 1 1 1 1 1 2 1 16 16 8 1 4 1 1
QT QT
Screw - Vite Screw - Vite Screw - Vite Hinge - Cerniera Key hole - Serratura Key - Chiave Oil level panel - Pannello spia olio Panel - Pannello Handle - Maniglia Support - Supporto montanti Angular - Angolare Angular - Angolare Panel - Pannello Column - Montante Rear panel - Pannello posteriore Electronic card panel - Pannello scheda elettronica Panel - Pannello Central panel - Pannello centrale Column - Montante Column - Montante Column - Montante Column - Montante Column - Montante Pre-filter panel - Pannello prefiltro Angular - Angolare prefiltro Pre-filter - Prefiltro Screw - Vite Washer - Rondella Screw - Vite Emergency push-button - Pulsante di emergenza Screw - Vite Electronic card - Scheda elettronica Base - Basamento
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.03.L.04)
REF. RIF.
CODE CODICE
QT QT
DESCRIPTION DESCRIZIONE
AIRBLOK100 SD 8 BAR AIRBLOK100 SD 10 BAR
SCA14G SCA14G
2/4 2/4
AIRBLOK100 SD SCA14G 2/4
CODE CODICE
7507490000 7020060000 7030020000 7018690000 7030020000 7201380000 7201420000 7200360000 7030130000 7011050000 7201400000 7030020000 5167030008 7012240000 5166960008 5167260008 5166750008 5166740008 5166760008 5166780008 5166880008 5166890008 5166900008 7014140000 7018590000 7011040000 7212420000 7459920020 7433380000 5166860008 5166770008 7014450000 5166920008 7212410000 7212410010 7212420010 5167000008 5167270008 5166980008 7248100000 5167020008 7500440000
REF. RIF.
200 201 202 203 204 205 205A 205B 206 207 208 209 210 211 212 212A 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 233A 234 235 236 237
1 6 10 2 12 1 1 1 6 26 1 10 1 26 1 1 1 2 1 1 1 1 1 8 4 16 2 2 1 1 1 8 1 1 1 2 1 1 2 1 1 1
QT QT
Radiator - Radiatore Nut - Dado Washer - Rondella Eyebolt - Golfare M10 Washer - Rondella Fan - Ventola radiale 400V / 50Hz Fan - Ventola radiale 400V / 60Hz Fan - Ventola radiale 460V / 60Hz Toothed washer - Rondella dentata Screw - Vite Fan - Ventola Washer - Rondella Ø6 Cover - Coperchio laterale Screw - Vite Fan box - Box ventola Fan box - Box ventola 400V-460V / 60Hz Support - Angolare Support - Angolare superiore Support - Angolare Support - Angolare superiore di irrigidimento Panel - Pannello superiore Panel - Pannello radiatore Panel - Pannello Screw - Vite Hinge - Cerniera Screw - Vite Electric fan filter - Filtro elettroventola Key hole - Serratura Handle - Maniglia blocca porta Panel - Pannello Support - Angolare Screw - Vite M5x50 Electric box - Cassetta elettrica Electric fan filter - Filtro elettroventola completo Filter - Filtro Filter - Filtro Support - Supporto Support - Supporto 400V-460V / 60Hz Support - Supporto Grille - Griglia Grille - Griglia Stretch eliminator - Pressacavo M20x1,5
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.03.L.04)
REF. RIF.
CODE CODICE
QT QT
DESCRIPTION DESCRIZIONE
AIRBLOK100 SD 8 BAR AIRBLOK100 SD 10 BAR
SCA14G SCA14G
3/4 3/4
AIRBLOK100 SD SCA14G 3/4
7413690000 7413800000 7509290000 7081130000 7030030000 7031010000 7020070000 7433360000 7084270000 7300230000 7433400000 7194330000
300 300A 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 315A 316 316A 317 317A 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345
7080780000 7230070000 7564330000 7082570000 7194340000 7085600000 7081010000 7500570000 5165700008 7080810000 7080810000 7500440000 7011030000 7012240000 5166940008
7432260000 7432970000 7564340000 7564390000 7433340000 7436080000 7433320000 7436090000 7082050000 7082640000 7083110000 7084370000 5167100008 7012240000 7084750000 7080800000 7562980000 7081160000 7191010000 7082300000
CODE CODICE
REF. RIF.
1 1 1 4 4 4 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 2 4 1 1 1 1 1 1 1 2 1 3 1 1 1 2 2 6 1
QT QT
Electric board - Apparecchiatura elettrica V400 50/60Hz Electric board - Apparecchiatura elettrica V460 60Hz Electric board plate - Piastra impianto elettrico Screw - Vite M8x40 Washer - Rondella Toothed washer - Rondella dentata Nut - Dado M8 Blocking door - Bloccaporte Joint - Raccordo 1/8" RESET push-button - Pulsante di RESET Contactor - Contattore Solenoid valve - Elettrovalvola Fuse carrier - Base portafusibili Fuse carrier - Portafusibili ventola Fan contactor - Contattore ventola Inverter - Inverter Transformer - Trasformatore Transformer - Trasformatore V460 / 60Hz Fan fuse - Fusibile ventola V400 / 50Hz Fan fuse - Fusibile ventola V460 / 60Hz Inverter fuse - Fusibile inverter Inverter fuse - Fusibile inverter V460 / 60Hz Joint - Raccordo "T" 1/4" Joint - Raccordo "L" 1/8" Joint - Raccordo "T" 1/8" Joint - Raccordo Support - Supporto filtri Screw - Vite Joint - Raccordo "L" 1/8" Ø10 Joint - Raccordo "L" 1/8" Ø6 Filter - Filtro condensa Joint - Raccordo Valve - Valvola unidirezionale Joint - Raccordo "T" 1/8" Ø6 Connector - Morsetto Joint - Raccordo "L" 1/8" Ø6 Rilsan FLUORFLON hose - Tubo Rilsan FLUORFLON Ø10 Pressure transducer - Trasduttore di pressione Joint - Raccordo diritto 1/8" Ø6 Solenoid valve - Elettrovalvola Joint - Raccordo Joint - Raccordo Stretch eleminator - Pressacavo M63x1,5 Support - Supporto Joint - Raccordo "L" 1/4" Ø6 Joint - Raccordo Stretch eleminator - Pressacavo M20x1,5 Screw - Vite TE M6x10 Screw - Vite Support - Supporto
DESCRIPTION DESCRIZIONE
VALID FROM 18/10/2004 - VALIDO DAL 18/10/2004 (REV.03.L.04)
CODE CODICE
4086450000 7230050000 7082980000 7082300000 7500430000 7433030000 7433190000 7436070000 7431640000 7080800000 7012280000
REF. RIF.
346 347 348 349 350 351 351A 352 353 354 355
1 1 1 1 8 1 1 1 1 1 2
QT QT
SCA14G SCA14G
Solenoid valve - Elettrovalvola Rilsan FLUORFLON hose - Tubo Rilsan FLUORFLON Ø6 Joint - Raccordo diritto 1/4" Joint - Raccordo Stretch eleminator - Pressacavo M16x1,5 Relay - Rele sequenza fasi V400 / 50Hz Relay - Rele sequenza fasi V440-480 / 60Hz Fuse - Fusibile 1A 500V ritardato Fuse - Fusibile 1A rapido Joint - Raccordo Screw - Vite
DESCRIPTION DESCRIZIONE
AIRBLOK100 SD 8 BAR AIRBLOK100 SD 10 BAR
4/4 4/4
AIRBLOK100 SD SCA14G 4/4
CODE CODICE
7082600000 7071350000 4094170000
REF. RIF.
1 2 3+2
Suction valve kit - Kit valvola di aspirazione Oil seal kit - Kit paraolio Oil seal kit+bearings kit - Kit paraolio+kit cuscinetti
DESCRIPTION DESCRIZIONE
SCA14
CODE CODICE
7082600000 4094520000 4094530000
REF. RIF.
1 2 3+2
Suction valve kit - Kit valvola di aspirazione Oil seal kit - Kit paraolio Oil seal kit+bearings kit - Kit paraolio+kit cuscinetti
DESCRIPTION DESCRIZIONE
SCA14G
MAINTENANCE SCHEDULE COMPRESSOR MODEL ____________________
SERIAL NO __________________
Date
Job description
Hours of use
Operator’s signature
............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................
......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... ......................................................... .........................................................
..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... ..................................... .....................................
............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................ ............................
Revisione 1.2 (01/2005) - Cod. 7.34.760.0000
