Transcript
Fiber Optic Rack Mount Enclosure, 3-Panel, 1 RMS I
N
S
T A
L
L
A T
I
O
N
I
N
S
T
R
U
C
T
I
O
N
S
Release Tab
Bracket Screws
Rack Screws
Rack Mount
Step 1. To open, push the release tab and slide out the tray from the rear to remove hardware. Installer rack mount brackets on the side. Note: Use #10 bracket screws.
Step 2. Mount the enclosure to a 19” distribution rack. Note: Use #12-24 rack screws.
Cable Management Spools
Circuit Label
Fiber Jumper Saddles
Velcro Tie Loops
Step 3. Install jumper saddles in slots on the front tray. Assemble cable management spools and install onto the slide out panel.
Step 4. Apply danger and circuit identification labels and Velcro® cable ties in the designated locations shown.
Fiber Optic Adapter
Flexi-panel door Push-pins
Step 5. Tilt locking lever and slide the tray back into the enclosure. Then install fiber optic adapter panels and cables. Note: Use cable ties to help manage cable routing.
888-ASK-4ICC
Step 6. Slide the tray in the enclosure and close the front with the flexi-panel door.
[email protected]
© Copyright 2012, ICC. ICC and ICC logo are registered trade name and trademark. All rights reserved. LGX is a registered trademark of OFS FITEL, LLC.
icc.com MSR-0413-1-Rev.B
Fiber Optic Rack Mount Enclosure, 3-Panel, 1 RMS I N
S
T A
L
L
A T
I
O
N
I
N
S
T
R
U
C
T
I
O
N
S
A C F
B
H
I G
D J E
ICFOR103BK A Fiber Enclosure, 1 piece B Cable Ties, 2 pieces C Pem Stud and Nuts, 1 pem stud and 2 nuts D Velcro® Tie Loops, 4 pieces E Cable Management Spool Kit, 8 spools and 4 F Fiber Jumper Saddles, 7 pieces
F
E
A T
U
R
E
G Rack Mount Bracket Kit •#10-32 X 3/8 Mounting Bracket Screws, 10 pieces •Mounting Brackets, 2 pieces H Circuit Identification Label, 1 piece I Danger Label, 1 piece J #12-24 x 5/8 Rack Screws, 4 pieces
S
A
N
D
B
E
N
E
F
I
T
S
S
O
R
I
E
S
S
• Enclosure is designed with a slide-out tray • It is designed to be rack mounted and fits standard 19” EIA rack mount widths • Made of durable 18 gauge steel with a black powder coated finish • Configure with three LGX compatible fiber optic adapter panels • 1 rack mount space (RMS) • 1.75” H x 17” W x 14” D
O
LC Fiber MPO Plug & Play Cassettes • 10G 50/125um (OM3) • Multimode, metal sleeves • Factory terminated and tested • Test results are included ICFC24ML1G ICFC12ML1G
P
T
I
O
N
A
L
A C
LC Quad Fiber Adapter • 6-Quad LC adapters • Supports up to 24-fibers • Multimode, metal sleeves ICFOPL161G
10G aqua
C
E
LC Fiber Adapter Panels • 6-Duplex LC adapters • Supports up to 12-fibers • Multimode / Single-mode • Ceramic sleeves ICFOPL16BK
12-LC duplex 6-LC duplex
Blue
SC Fiber Adapter Panels • 6-Duplex SC adapters • Supports up to 12-fibers ICFOPC16BK Blue • Multimode, metal sleeves ICFOPC26BK Blue • Multimode / Single-mode • Ceramic sleeves
888-ASK-4ICC
[email protected]
© Copyright 2012, ICC. ICC and ICC logo are registered trade name and trademark. All rights reserved. LGX is a registered trademark of OFS FITEL, LLC.
icc.com MSR-0413-1-Rev.B
