Transcript
INSTRUCTIONS FOR INSTALLATION AND USE
FIBRE OPTIC LIGHT SOURCE TYPE FL 75 / FL75E
Operating instructions FL 75 - Ul. 02072004, Cat.No.: 99082033
Page 1 af 4
Contents Introduction ............................................................................... Page 2 Operation ................................................................................... Page 3 Maintenance .............................................................................. Page 3 Fault finding .............................................................................. Page 4 Spare parts ................................................................................. Page 4 Technical data............................................................................ Page 4 Instruktion sheet.........................................................................Page 5
Introduction Roblon light source type FL 75 is designed and constructed to provide an effective light source for fibre optic illumination systems. The light intensity and radiant heat outputs are optimised to ensure the longest possible lamp life. FL 75 fulfils a number of general fibre optic light source requirements, including:· High intensity light output. · The light output may be launched into a single fibre bundle, or into a multiple harness containing up to 800 x 1.0 mm separate cords, for star effect etc. · A motor driven variable colour or twinkle facility is optional. To obtain the best results, please read these notes carefully before putting the unit into service.
Operating instructions FL 75 - Ul. 02072004, Cat.No.: 99082033
Page 2 af 4
Connecting to power Carefully unpack the unit, which is supplied complete. If the unit has been ordered with colour or twinkle facility, this is also already fitted. Plug into the main power supply. 120v 50/60 Hz ONLY Operation Fully insert the chosen fibre bundle or harness into the light output point and secure firmly with the grub screw. The unit is now ready for use, and the lamp is started by pushing the small button situated above the power lead input at the rear. Maintenance The outside of the cabinet may be cleaned with a damp lint-free cloth. In a dusty environment it is recommended that the interior assembly be inspected every three months, to ensure that the cooling system is not impaired and that the lamp and reflector surfaces are clean. Dirty lamp and reflector surfaces will reduce the light output and the lamp life. They may be cleaned if necessary, with a soft dry brush, or a lint-free cloth and alcohol. Replace the lamp at 6000 hour operation intervals. N.B. Do not touch the lamp or reflector surfaces with bare fingers, as finger grease will cause hot spots and impair the function and lamp life. Changing the lamp: 1. Disconnect the unit from the main power supply. 2. Remove the covers. 3. Remove the retaining spring from the lamp. 4. Carefully remove the lamp and detach the lamp base. 5. Install a new lamp, Philips no. 14515, Cat.No. 65127595, reversing the above procedure. Take care not to touch the lamp or reflector surfaces with bare fingers. Should this accidentally happen, clean with alcohol as described above. 6. Replace the covers and check the operation. Changing the colour wheel etc: Disconnect the unit from the power supply, and remove the covers, to gain access to the colour wheel assembly.
Operating instructions FL 75 - Ul. 02072004, Cat.No.: 99082033
Page 3 af 4
Fault finding If the lamp will not light:Check the power supply. Check the fuse. Ensure that the lamp base is secure. Replace the lamp if necessary as previously described. If the light output is unsatisfactory:Ensure that the fibre cord or harness is fully inserted and secured. If the running time of the lamp is 6000 hours or more, replace it. If the performance is still unsatisfactory, please contact Roblon Fiber Optic Division. Spare parts Catalogue No.65127595 - 51000050
Philips no. 14515 lamp Standard colour wheel
Technical data Lamp: Focus point: Light intensity at focus: Power unit: Cooling:
Philips no. 14515, 12 volt 75 watt, low voltage halogen. 9 mm Ø - 28 mm Ø. Typically 550 lumen. Toroidal transformer 90VA. Radial fan.
Produced by Roblon Lighting Nordhavnsvej 1 9900 Frederikshavn Denmark
Tel: +45 9620 3300 Fax: +45 9620 3399
[email protected] www.roblon.com
Operating instructions FL 75 - Ul. 02072004, Cat.No.: 99082033
Page 4 af 4
