Fibre Optic Sliding Rear Angled P/panel

Transcript

1 2 3 4 DO NOT SCALE A B PRINTING INSTRUCTIONS:PRINT INSTRUCTION SHEET ON A4 SIZE STANDARD WEIGHT PAPER. DOUBLE SIDED PRINT COLOUR OF PRINT:- BLACK. C D FILE LOCATION: S:/USER INSTRUCTIONS/16XXXXX/1676740-C.doc Finish Dims not in tol. . . Scale . . . . . . . . . . . . . . . . . . . . . . . . . . C 9 02 BS 02/07/10 WD 02/07/10 BLN 02/07/10 BS 30/03/10 RJT 14/04/10 BLN 16/04/10 BS 23/02/10 RJT 25/02/10 BLN 25/02/10 B A Iss 52 12 2 1 28 5 28 20 81 27 20 01 MCO Drawn Date FORM E54 ISSUE:8 16.10.06 Checked Date We reserve all rights for this techn copyright. c This document must no without our agreement, and must not parties in any other way. We shall d rights and there may be other legal Material: Description: ical document, including patent righ t be reproduced or passed on to thir be misused by the recipient or by th emand damages for any infringement o consequences. A4 STANDARD ts and d parties ird f these Projection WEIGHT PAPER Dimensions in millimetres FIBRE OPTIC SLIDING REAR ANGLED P/PANEL Sheet Project: 1of 9 108451 Drawing No: Approved Date PROENG FILE: 1676740 Article No. Replacement for: 1676740 01 C Code 1676740 01B Sht Iss ® KRONE 2 HEREFORD ST BERKELEY VALE 2261 NSW AUSTRALIA TEL: (02) 4389 5000 FAX: (02) 4388 4499 E INSTALLATION INSTRUCTIONS LKH FIBRE TRAY PRODUCT No. 6877 1 001-10 6877 1 001-11 Components Supplied Sliding Rear Angled Fibre Patch panel 1RU x 1 Spiral Tube Wrap 0.5m x 2 Strain Relief Post x 2 M6 x 12mm Pan Head Screws x 4 Black Cable Entry Plug x 4 (not supplied with 6877 1 001-11) Cable Gland GN20 x 2 (not supplied with 6877 1 001-11) Part No: 1676740 Issue: C Sheet 1 of 8 INSTALLATION INSTRUCTIONS LKH FIBRE TRAY PRODUCT No. 6877 1 001-10 6877 1 001-11 M6 Shake proof Washer x 2 M6 x 10mm Pan Head Screws x 5 Non-adhesive Label x 1 PART No: 1682129 M6 Cage Nut x 4 Caution Minder Label x 2 M3 x 4mm Pan Head Screws x 2 Part No: 1676740 Issue: C Sheet 2 of 8 INSTALLATION INSTRUCTIONS LKH FIBRE TRAY PRODUCT No. 6877 1 001-10 6877 1 001-11 Assembly Instructions 1. Place the fibre tray on a flat clean surface. 2. Remove metal lid by removing the fasteners on each side and the thumbscrew on the front. 3. Determine the 2 positions where the cable will enter the fibre tray. Insert and fasten the cable glands into the desired positions as shown. 4. Wherever cable entries are not used, place cable entry plugs into the remaining positions as shown. 5. Position the strain relief posts to the fibre tray using the M6 x 10mm screws and M6 shake proof washer as shown. Fastener to remove lid M6 x 10mm inserted from the underside of tray Fastener to remove lid Part No: 1676740 Issue: C Sheet 3 of 8 INSTALLATION INSTRUCTIONS LKH FIBRE TRAY PRODUCT No. 6877 1 001-10 6877 1 001-11 Assembly Instructions (cont’d) 6. Connector panels (sold separately) can be assembled to the fibre tray as shown. Pulling the rivet head out allows the connector panels to be installed/removed. Pushing the rivet head back in allows the connector to be secured to the fibre tray. 7. Connector panels can be mounted either facing left or right depending on application required. Connector panels can both be facing in the same or opposing directions. Locating hole Push rivet Part No: 1676740 Issue: C Sheet 4 of 8 INSTALLATION INSTRUCTIONS LKH FIBRE TRAY PRODUCT No. 6877 1 001-10 6877 1 001-11 Fasten here Fasten here Assembly Instructions (cont’d) 8. Splice cassettes (sold separately: FST-HS-48) can be fixed into the centre of the fibre tray as shown using the M3 x 4mm fasteners supplied. Part No: 1676740 Issue: C Sheet 5 of 8 INSTALLATION INSTRUCTIONS 50 95 225 LKH FIBRE TRAY PRODUCT No. 6877 1 001-10 6877 1 001-11 Assembly Instructions (cont’d) 9. The mounting brackets can be orientated in 2 forward and 1 rearward facing positions. The fibre tray brackets are pre-assembled in the 95mm forward position as shown on the far left. To mount the bracket in the forward 50mm position (as shown – second from left) – remove the 3 fasteners and position the bracket forward in the last 3 mounting bracket holes. The patch panel must be supported at the rear when using the forward 50mm mounting position. The rear mounting position of 225mm (as shown far right) is possible by rotating the bracket 180˚ and aligning it to the desired mounting holes ensuring that all 3 fasteners are used. Part No: 1676740 Issue: C Sheet 6 of 8 INSTALLATION INSTRUCTIONS LKH FIBRE TRAY PRODUCT No. 6877 1 001-10 6877 1 001-11 Assembly Instructions (cont’d) 10. Ensure that the front thumbscrew and 2 side screws are retightened to close the fibre tray. 11. Mount the fibre tray to a 19 inch rack using the cage nuts and M6 x 12mm screws provided. 12. Once installation has finished – tear the supplied non-adhesive label along the perforated edge. Insert both labels into the front clear sleeves. 13. Earth the fibre tray using the M6 x 10mm pan head screw supplied. The earth point is located on the rear of the tray. Side screw for lid Earth to rear of fibre tray Insert paper labels into sleeves Thumbscrew Part No: 1676740 Issue: C Sheet 7 of 8 INSTALLATION INSTRUCTIONS LKH FIBRE TRAY PRODUCT No. 6877 1 001-10 6877 1 001-11 Spiral Wrap Installation 14. Thread the stripped optical fibre inside the spiral wrap for protection. The spiral wrap should be routed as shown in the image below to allow for the sliding tray to operate. 15. Expose the CSM and strain relief out from the side of spiral wrap and secure to the terminal posts. 16. Secure the end of the spiral wrap to the cable guide as shown using Velcro. Do not secure the spiral tube wrap to the inside of the cable guide. Velcro Tie the spiral tube wrap to the outside of the cable guide Pull the CSM through the side of the spiral wrap and secure it through the hole in the terminal post Spiral wrap Pull the Kevlar strain relief through the side of the spiral wrap and secure it to the terminal post by wrapping it around the M6 fastening screw before tightening. Optic fibre Part No: 1676740 Issue: C Sheet 8 of 8