Find Out What`s Behind, In Real Time

Transcript

SV-6900.BL Third Brake light Wide-angle camera with night vision INSTALLATION INSTRUCTIONS: The SV-6900.BL is a special designed commercial camera inset inside a brake light housing. It is specifically designed to be mounted in the third brake light position on a school bus or delivery truck. The wide-angle 150° CMOS color camera will give the driver the best viewing angle when backing up and it is also equipped with night vision for better illumination in low-light. FEATURES: • • • • • • • Replaces the existing third brake light or adds a third brake light to the vehicle 150° ultra wide-angle camera with night vision Easily mounts to vehicle with minimal installation time Constructed of high-grade ABS plastic Reverse image The OEM cam easily connects with other SecurView products such as any of the LCD monitors. It can also be integrated with your existing OEM or aftermarket LCD/TFT displays. The Securview™ SV-6900.BL is designed specifically for the Ford Transit Van vehicle and may not work well on other vehicles. Please check the vehicle before installing to make sure the camera can be properly placed INSTALLATION MOUNTING: 1. The SV-6900.BL is specifically designed to take the place of the third brake light on a school bus or delivery truck or to be mounted high up on the back of the vehicle giving it a third brake light as well as a reverse camera. The first thing to do is locate and remove the existing third brake light. 2. Most third brake lights will be held in place by screws from the outside. Make sure to carefully remove the screws and remove the third brake light housing. You may need to use a panel removing tool to help pry the brake light loose. Be careful not to scratch any of the surface paint on the outside of the vehicle 3. If you are adding the SV-6900.BL to a vehicle that does not have the third brake light already, then you will need to drill a hole to route the wire harnesses into the vehicle. Make sure to double check behind the mounting surface to make sure nothing will be spliced or damaged. 4. Make the necessary connections to the brake light wiring so that the SV-6900.BL lights can turn on when the brake is applied (See wiring section) 5. Route the wire harness into the vehicle through the pre-existing hole of grommet that the brake light wiring is coming though. 6. Remove the cover from the adhesive baking from the SV-6900.BL and place it into the mounting area. Use the provided screws to secure the camera into place on the vehicle. The SV-6900.BL can be used to either replace an existing third brake light or simply to add a third brake light while giving the driver the added convenience of a 150° CMOS reverse camera CAMERA: 1. The color CMOS camera is maintenance-free, waterproof (IP-68) and vibration resistant. 2. This camera is designed to work well in day time or night time conditions. 3. The camera is completely electronic. There are NO manual adjustments for focus, etc. WIRING: 1. Carefully route the wiring harness of the camera into the vehicle either using a pre-existing factory grommet or by drilling a hole. If drilling a hole, be careful not to damage anything behind the mounting surface. 2. Choose a convenient place to run the camera cable up the left or right side of the vehicle. As a rule of thumb, try to avoid main factory harness looms that may contain high levels or RF noise or interference. 3. On the brake light harness (The loomed wire harness with the white plastic connector) Connect the Red wire to the 12 volt brake light wire and connect the Black wire to chassis ground. This will make the lights for the SV-6900.BL illuminate when the brake pedal is pressed. 4. On the camera harness, Connect the Red wire to the 12 volt reverse light wire and connect the Black wire to chassis ground. 5. Run the Yellow RCA video cable to the monitor’s video input or reverse camera input. 6. The White RCA does not need to be connected RED WIRE POWER CONNECTOR Connect to +12V Reverse Light MONITOR BLACK WIRE Ground YELLOW RCA Connect to Monitor WHITE RCA No Connection RED WIRE BLACK WIRE Ground Connect to +12V Brake Light TECH SUPPORT: (800) 998-6880 SPECIFICATIONS: 1/4 Inch Color CMOS Sensor Dimension (In.): 1⅞"(L) × 7¾"(W) × 1⅝"(D) Weight: 10 Oz. Pixels: 512 (H) x 492 (V) Resolution: > 250,000 pixels 420 TV lines Minimum Illumination: 0.5 LUX / F 1.2 Lens Type: Wide Angle Horizontal Angle: 150° Vertical Angle: 90° Video Output: 1.0 V P-P composite (75 Ohm load) Supply Voltage: +12VDC Power Consumption: 150mA Shutter: 1/50 s – 1/100000s White Balance: Automatic Gamma Correction: 0.45 S/N Ratio: More than 48dB Operating Temp: -22° to 176° F (-30° to 80° C) Gain Control: Automatic DISCLAIMER: Under no circumstances shall the manufacturer or distributor of the Securview™ be held liable for consequential or incidental damages sustained in connection with the use of the Securview™ Rear Vision System. The Securview™ is designed as a safety enhancement device and is in no way intended as a replacement for rear-view mirrors, side-view mirrors or physically checking the surroundings when backing a vehicle. Always check surroundings for safety when backing! Objects on the monitor are closer than they appear. For the best fit, modification of the vehicle license may or may not be necessary. It is the sole responsibility of the vehicle owner to check and verify any and all State or Federal Motor vehicle codes with regards to modifications of vehicle license plates. The manufacturer of the Securview™ assumes no liability or responsibility whatsoever with regards modifications of the license plate. www.crimestopper.com [email protected] Phone (800) 998-6880 FAX (805) 581-9500 © 2012 Crimestopper Security Products 4-28-2012