Transcript
INSTALLATION INSTRUCTIONS
Suspended Ceiling Mount Kit for 8” to 32” ViewZ Monitors Model: VZ-CMK02
NORTH AMERICA
1220 N. Kraemer Blvd. Anaheim, CA 92806 USA USA and Canada Phone: 1-888-99-ViewZ Other Locations Phone: (001) 714-630-3380 Fax: (001) 714-630-2335
853177002878
VZ-CMK02
Contents Weight Limit...................................................................................................................................................................... 2 Warning Statements......................................................................................................................................................... 2 Installation Tools............................................................................................................................................................... 3 Parts List.......................................................................................................................................................................... 3 Mounting Hardware.......................................................................................................................................................... 4 Features........................................................................................................................................................................... 5 Installing the VZ-CMK02 Mount....................................................................................................................................... 6 Introduction................................................................................................................................................................ 6 Wood Stud Installation............................................................................................................................................... 6 Solid Ceiling Installation............................................................................................................................................. 8 Attaching the VZ-CMK01A............................................................................................................................................... 9 Mounting Hardware........................................................................................................................................................ 10 Selecting the Mounting Hardware............................................................................................................................ 10 Universal Spacer Installation....................................................................................................................................11 VZ-AP200 Adapter Plate Installation.........................................................................................................................11 Attaching the Flat Panel to the VZ-CMK02 Mount......................................................................................................... 12 Adjusting the Mount Tension.......................................................................................................................................... 13 Technical Specifications................................................................................................................................................. 13 Warranty......................................................................................................................................................................... 14 Disclaimer....................................................................................................................................................................... 14
Weight Limit Maximum Flat Panel Weight:
50 lbs.
THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF THE FLAT PANEL. IF NOT, THE CEILING STRUCTURE MUST BE REINFORCED.
Warning Statements PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE. PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED, AS OUTLINED IN THESE INSTALLATION INSTRUCTIONS. FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE, SERIOUS PERSONAL INJURY, OR EVEN DEATH. SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY. VIEWZ DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY VIEWZ PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS. At least two qualified people should perform the assembly procedure. Personal injury and/or property damage can result from dropping or mishandling the projector. If mounting to wall studs or ceiling studs, make sure that the mounting screws are anchored into the center of the wall studs or ceiling studs. Use of an edge-to-edge stud finder is recommended. Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires in wall. Cutting or drilling into an electrical line may cause serious personal injury. Make sure there are no water or natural gas lines inside the wall where the mount is to be located. Cutting or drilling into a water or gas line may cause severe property damage or personal injury. This product is intended for indoor use only. Use of this product outdoors could lead to product failure and/or serious personal injury. Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact. Contact ViewZ with any questions: (888) 99-ViewZ
[email protected]
Page 2
Visit the ViewZ website at http://www.viewzusa.com
Installation Instructions
VZ-CMK02
Installation Tools The following tools may be required, dependent upon your particular installation. Not all of these tools are provided by ViewZ, but you can purchase them at your local hardware store.
2 1
Pencil
Power Drill
Tape Measure
⅛˝ Wood Drill Bit
Protective Eyewear
Concrete Drill Bit
Phillips Tip Screwdriver
Socket Wrench
Ladder
Parts List Your ViewZ product is shipped with all proper installation hardware and components. Make sure that none of these parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the installation and contact ViewZ (888) 99-ViewZ. VZ-CMK02 Mount Hardware
VZ-CMK-P3 (Qty 1)
M5 Flat Washers (Qty 4)
Universal Spacers (Qty 30)
Thread Depth Indicator (Supplied)
Installation Instructions
VZ-AP200 Adapter Plate (Qty 1)
VZ-CMK01A(Qty 1)
#14 x 2″ Wood Screws (Qty 4)
M3 Allen Wrench (Supplied)
M4 Flat Washers (Qty 4)
14mm Socket (Supplied)
Visit the ViewZ website at http://www.viewzusa.com
Page 3
VZ-CMK02
Parts List (cont’d) Mounting Hardware
M4 x 10mm Flat Head Screw (Qty 6)
M5 x 10mm Screw (Qty 4)
M4 x 16mm Flat Head Screw (Qty 6)
M5 x 16mm Screw (Qty 4)
M4 x 20mm Flat Head Screw (Qty 6)
M5 x 20mm Screw (Qty 4)
M4 x 30mm Flat Head Screw (Qty 6)
M5 x 30mm Screw (Qty 4)
M4 x 45mm Flat Head Screw (Qty 6)
M5 x 45mm Screw (Qty 4)
M6 x 10mm Screw (Qty 4)
M4 x 5mm Screw (Qty 4)
M6 x 16mm Screw (Qty 4)
M4 x 10mm Screw (Qty 4)
M6 x 20mm Screw (Qty 4)
M6 x 30mm Screw (Qty 4)
M6 x 45mm Screw (Qty 4)
Page 4
Visit the ViewZ website at http://www.viewzusa.com
Installation Instructions
VZ-CMK02
Features
Extendable Adjust for perfect placement and ease of viewing
Radial Glide® 360° rotation and 15° of adjustment in any direction
Cable Routing Allows for easy routing of power and signal cables
Dynamic Viewing 360° of left or right swivel
VESA Compatible Compatible with 75mm x 75mm, 100mm x 100mm, 200 mm x 100mm and 200mm x 200mm mounting patterns Installation Instructions
Visit the ViewZ website at http://www.viewzusa.com
Page 5
VZ-CMK02
Installing the VZ-CMK02 Mount Introduction Your VZ-CMK02 mount may be secured to either a single ceiling stud or a solid surface ceiling, such as concrete. The VZ-CMK02 allows tilt and pivot adjustments ±15° from center, 360° side-to-side swivel, and cable access. The VZ-CMK-P3 allows height adjustment from 24 to 46 inches. Plus it also features two cable access openings. Please read these installation instructions once thoroughly before attempting to install your ViewZ product. Please take a minute to familiarize yourself with the contents of the package and make sure you have all the parts and tools you need to safely complete the installation. In addition, some steps of this installation may require two people to prevent personal injury and/or damage to your projector. Please observe all warnings in the following installation procedure and utilize proper safety equipment at all times.
Wood Stud Installation Step 1
®® ¯¯
Use a stud finder to locate a ceiling stud closest to your desired installation location. Identify the center of the ceiling stud. Use a pencil to mark the location of the ceiling stud center. The target arrow indicates the direction of the non-viewing side of the flat panel.
CSe tud nte r Step 2
®®
Place the VZ-CMK-P3 ceiling plate into position against the ceiling with the mounting holes aligned with the center of the ceiling stud. Use a pencil and mark two (2) mounting hole locations through each of the mounting points A in the VZ-CMK-P3 ceiling plate.
Page 6
Visit the ViewZ website at http://www.viewzusa.com
Installation Instructions
VZ-CMK02 Step 3
®®
Set aside the VZ-CMK02 Mount. Drill a pilot hole in the center of each mark using a power drill and 1/8˝ drill bit.
Pilot Holes When a screw is driven into a material, such as wood, it can act as a wedge, generating outward pressure which can cause many materials to split. Drilling a small pilot hole in the material into which the screw will be driven causes less ‘wedging’ to take place, thereby reducing the likelihood of the material being split. It also reduces the possibility of the screw head from being sheared off by torque
Step 4
®® ¯¯
Realign the VZ-CMK02 with the pilot holes. Insert one (1) #14 x 2˝ screw through each of the mounting holes A in the bottom of the VZ-CMK-P3 ceiling plate and into the pilot holes. Manually tighten each screw until the VZ-CMK-P3 ceiling plate is secure against the ceiling. Do not overtighten the #14 x 2˝ screws.
Proceed to the “Attaching the Projector Plate” section.
Installation Instructions
Visit the ViewZ website at http://www.viewzusa.com
Page 7
VZ-CMK02
Solid Ceiling Installation Your VZ-CMK02 flat panel mount can be mounted to a solid surface ceiling with a minimum 6" thickness. Concrete wedge anchors must be used for concrete installation. It is recommended that ¼” wedge anchors be used. A concrete bit must be used to drill the pilot hole. Both wedge anchors and concrete drill bits are not supplied, but can be purchased at your local hardware store.
Example Wedge Anchors and Concrete Bit (Commercially Available)
Step 1
®®
Place the VZ-CMK-P3 ceiling plate into position against the ceiling. Use a pencil and mark four (4) mounting hole locations through each of the mounting points B in the VZ-CMK-P3 ceiling plate. The target arrow indicates the direction of the non-viewing side of the flat panel.
Step 2
®® ¯¯
Drill a hole at each mark using the appropriate diameter concrete bit for your wedge anchor. Remove the nut and washer from the wedge anchors. Insert a wedge anchor into each hole. If necessary, a hammer can be used to lightly tap each wedge anchor into place.
Page 8
Visit the ViewZ website at http://www.viewzusa.com
Installation Instructions
VZ-CMK02 Step 3
®®
Move the VZ-CMK-P3 ceiling plate back into position. Thread a wedge anchor nut (and washer, if provided with the wedge anchor) onto each threaded wedge anchor shaft. Do not tighten any of the wedge anchor nuts (and any washers) until all nuts and washers are threaded onto the shafts. Do not overtighten the wedge anchor nuts.
Proceed to the “Attaching the VZ-CMK01A” section.
Attaching the VZ-CMK01A
®®
Screw the VZ-CMK01A coupling adapter to the VZCMK-P3 adapter or 1½" (NPT) Pipe. Secure the coupling with the M6 set screw (supplied). The VZ-CMK01A must be threaded on four complete turns before tightening down the set screw.
If you are having difficulty achieving four complete turns, insert a screwdriver through the access hole and apply pressure while turning the VZ-CMK01A (see below).
Installation Instructions
Visit the ViewZ website at http://www.viewzusa.com
Page 9
VZ-CMK02
Attaching the VZ-CMK01A
¯¯
Use the M3 Allen wrench to tighten the M6 x 6mm set screw located on the side of the VZ-CMK02 mount.
M3 Allen Wrench
Proceed to the “Mounting Hardware” section.
M6 x 6mm Set Screw
Mounting Hardware Selecting the Mounting Hardware
®® ¯¯ °° ±±
Insert a small straw or toothpick into the threaded inserts found on the back of the flat panel. Use a pencil to mark the depth of the threaded insert on the small straw or toothpick. Mark the straw or toothpick 1/8” above the depth of the threaded insert, as shown in Figure 1. Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick’s 1/8” allowance mark. Locate the correct diameter screw for the threaded insert. If the screw you selected is longer than the 1/8” allowance mark on the small straw or toothpick, as shown in Figure 2 and Figure 3, do not use this screw. The screw length must not bypass the mark.
²²
Marking the 1/8” Allowance
Test each size of the screws provided.
Small Straw or Toothpick
The correct screws should thread easily into the mounting point and not pull out when tension is applied. Does your flat panel have:
●● Recessed mounting points? ●● Uneven mounting points? ●● A curved back? ●● Any obstruction near the mounting point?
Small Straw or Toothpick
Depth Plus 1/8” Allowance Mark
Small Straw or Toothpick
Depth Plus 1/8” Allowance Mark
If Yes, you must install Universal Spacers. Proceed to the “Universal Spacer Installation” section. If No, skip to the “VZ-AP200 Adapter Plate Installation” section.
Page 10
Visit the ViewZ website at http://www.viewzusa.com
Installation Instructions
VZ-CMK02
Mounting Hardware (cont’d) Universal Spacer Installation ViewZ’s Universal Spacers allow you to attach the mounting bracket to flat panels which have recessed or uneven mounting points. Each Universal Spacer adds ¼˝ to the distance between the Adapter Plate and your flat panel. The Universal Spacers must be stacked and oriented as shown. The Universal Spacers must only be installed between the Adapter Plate and your flat panel. The Universal Spacers will fit M4, M5, M6 and M8 screw sizes. Does your flat panel have:
●● 75mm x 75mm VESA mounting points or
100mm x 100mm VESA mounting points? Proceed to the “Attaching the Flat Panel to the Mount” section.
●● 100mm x 200mm mounting points or 200mm x 200mm mounting points?
Proceed to the “VZ-AP200 Adapter Plate Installation” section.
VZ-AP200 Adapter Plate Installation
The VZ-AP200 LCD Mount Adapter is used attach flat panels with 100mm x 200mm and 200mm x 200mm mounting points to the VZ-CMK02 mount.
Determine which mounting points will be used. Refer to the “Technical Specifications” section for VZ-AP200 Adapter Plate mounting points.
®®
Place your monitor face-down on a soft and flat surface. ¯¯ Secure the VZ-AP200 Adapter Plate to the back of the monitor using the following hardware: If you are using the 200mm x 100mm mounting points, you must use the M4 x 10mm Phillips flat head screws to secure the VZ-AP200 Adapter Plate to the flat panel.
•
• If you are using the 200mm x 200mm mounting points...
...and you selected M4 screws from the “Selecting the Mounting Hardware” section, you must also use M4 flat washers. ...and you selected M5 screws from the “Selecting the Mounting Hardware” section, you must also use M5 flat washers. Proceed to the “Attaching the Flat Panel to the Mount” section.
Installation Instructions
Visit the ViewZ website at http://www.viewzusa.com
Page 11
VZ-CMK02
Attaching the Flat Panel to the VZ-CMK02 Mount 1) Insert two (2) M4 screws into the top two mounting points of your flat panel or VZ-AP200 Adapter Plate. Thread the M4 screws to one-half of their length into the flat panel or VZ-AP200 Adapter Plate, but do not tighten the M4 screws at this time. The length of the M4 screws are dependent upon whether or not you are using the VZ-AP200 Adapter Plate, as shown below. Make certain you use the correct length for your specific installation. If you are using the VZ-AP200 Adapter Plate, use the B mounting points. Refer to the “Technical Specifications” section for VZ-AP200 Adapter Plate mounting points. 2) Insert the heads of the M4 screws through the keyhole slots. 3) Insert two (2) M4 screws, of the proper length for your installation, into the bottom mounting points. 4) Tighten all M4 screws. Do not overtighten the mounting hardware. Proceed to the “Adjusting the Mount Tension” section. Flat Panel without VZ-AP200 Adapter Plate
Flat Panel with VZ-AP200 Adapter Plate
M4 x 5mm Screw
M4 x 10mm Screw
VZ-CMK02 Mount
Thread Insert in Flat Panel or Adapter Plate
Keyhole Slot
Page 12
M4 Screw Partially Threaded Into Flat Panel or Adapter Plate
Visit the ViewZ website at http://www.viewzusa.com
Installation Instructions
VZ-CMK02
Adjusting the Mount Tension Use a socket wrench and the supplied 14mm socket to loosen or tighten the tension nut. Turn the tension nut clockwise to increase tension. Turn the tension nut counter- clockwise to decrease tension. Do not overtighten the tension nut.
• •
Tension Adjustment
Technical Specifications All measurements are in inches [mm].
A: 75mm x 75mm VESA mounting points. B: 100mm x 100mm VESA mounting points. C: 200mm x 100mm mounting points. (M4 x 10mm Phillips flat head screws only) D: 200mm x 200mm mounting points. (If M4 screws are used, M5 washers must be used as well)
Installation Instructions
Visit the ViewZ website at http://www.viewzusa.com
Page 13
VZ-CMK02
Warranty VIEWZ LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Viewz warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What ViewZ Will Do At the sole option of ViewZ, ViewZ will repair or replace any product or product part that is defective. If ViewZ chooses to replace a defective product or part, a replacement product or part will be shipped to you at no charge, but you must pay any labor costs. What is Not Covered; Limitations VIEWZ DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS. VIEWZ DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. VIEWZ IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer purchaser must accompany all warranty claims. Warranty claims must also include a description of the problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to ViewZ Customer Service at 1-888-99-ViewZ. Warranty claims will not be accepted over the phone or by fax. ViewZ Attn: Warranty Claim 1220 N. Kraemer Blvd. Anaheim, CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Disclaimer ViewZ intends to make this manual accurate and complete. However, ViewZ makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. ViewZ makes no representation of warranty, expressed or implied, regarding the information contained herein. ViewZ assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
©ViewZ 2011
Page 14
Visit the ViewZ website at http://www.viewzusa.com
Installation Instructions
