Transcript
Firecom 600-0176-00 RevD:Layout 1 8/19/11 3:15 PM Page 2
PROGRAMMABLE SQUELCH A
OUT OF RANGE
SPECIFICATIONS Noise Reduction This Firecom Headset provides 24dB noise attenuation when properly fitted. Any modification to the Headset will reduce the Headset performance and hearing damage could occur. Always wear hearing protector in areas that have been identified as high noise locations.
Turn ON Headset and connect to the Up=PTT On Base Station. C
B Turn Headset OFF.
Power On
Maximum 1600 feet LINKS WIRELESS BASE
WARNING
POWER
1 2 3 4 5
INTERCOM
PAIR
Holding the toggle switch during turn ON for longer than 5 seconds will unpair the Headset from the Base.
turn ON the Headset. Toggle Up
toggle switch or PTT button D Release when the GREEN LED lights, watch the
• When approching range limit, headset beeps 1 time every 10 seconds before losing LINK to Base Station • Beep stops when user returns into range Automatic Sleep If the Headset does not reconnect to the base station within 5 minutes, it will enter a low power mode. Cycle power ON to the Headset in order to reconnect the link to the Base Station.
RED LED; it will flash the current squelch setting (i.e. 5 flashes=squelch setting 5).
On
change squelch settings; press toggle E Toswitch UP or hold PTT button down on the dome and count the number of Red LED flashes. Press the toggle UP or press the PTT button to change the setting to the next range and view the number of RED LED flashes. Once the squelch setting reaches level 9, the next position will return to level 1. For -57 headsets with toggle switch, go to step F. For all other headsets go to step G.
MAINTENANCE Care and Maintenance • Inspect ear seals and mic muff frequently for wear. Replace at 6 month intervals. If you see any defect such as holes or cracks in the ear domes, ear seals, or headband, headset should be immediately repaired or replaced. • Do not remove the foam speaker cover.
Programmable Squelch 130dB
130dB
125dB
125dB
9
120dB 115dB 6
110dB 4
• To ensure proper function, keep the microphone away from excessive moisture. Do not store Headset in high temperature environments or direct sunlight. • Wipe Headset and ear seals with a mild soap and water mixture only. The foam mic muff may be removed and cleaned in a mild detergent, or replaced by ordering from Firecom.
100dB 95dB
2 1
90dB
FACTORY SETTING
85dB
80dB
HIGH NOISE ENVIRONMENT
For -57 headsets with toggle switch: To change squelch settings of the bottom position; Press the toggle DOWN to change the setting to the next range and view the number of GREEN LED flashes. Once the squelch setting reaches level 9, the next position will return to level 1.
To save the setting, cycle power.
WARNING
85dB
-57 FACTORY SETTING LOW NOISE ENVIRONMENT
G
105dB
3
95dB
F
110dB
5
100dB
80dB
115dB
7
105dB
90dB
120dB
8
Never immerse any part of the headset in water.
Ear seals and mic muff removal
Federal law requires the following statements: “Although hearing protectors can be recommended for protection against the harmful effects of impulsive noise, the Noise Reduction Rating (NRR) is based on the attenuation of continuous noise and may not be an accurate indicator of the protection attainable against impulsive noise such as gunfire.”
Example 1. The environmental noise level as measured at the ear is 92dBA. 2. The NRR is 24dB. 3. The level of noise entering the ear is approximately equal to 92dBA – NRR or 68dB. “For noise environments dominated by frequencies below 500 Hz, the C- weighted environmental noise level should be used.” FCC/IC Compliance This device complies with FCC Part 15 Rules and IC RSS-213 Rules. Operation of this is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interference that may cause undesired operation. FCC/IC RF Exposure Warning • This product complies with FCC radiation exposure limits set forth for an uncontrolled environment. • This product may not be collocated or operated in conjunction with any other antenna or transmitter. • This headset has been tested and meets the FCC RF exposure guidelines. Max. SAR is 0.003 W/ kg.
7340 SW Durham Road • Portland, OR 97224 USA 1-800-527-0555 • Phone: 503-684-6647 • Fax: 503-620-2943 www.firecom.com • email:
[email protected] © 2011, A Division of Sonetics Corporation. Specifications subject to change without notice.
Weight (Over the Head) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3lb (0.58 Kg) Weight (Behind the Head) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2lb (0.53 Kg) RF - Range: 1600 feet open field - Digital encoding for secured communications - Interference free communications for up to 60 headsets operating in close proximity
WARRANTY Two-Year Limited Warranty to the Original Purchaser See addendum for full warranty details.
Power - 3.7V rechargeable lithium polymer battery - >24 hours battery life when operating @25°C - Over voltage, under voltage, over current and over temperature protection - AC Charge source: supplied 12v, 500mA wall charger - DC Charge source: 5v to16v, 1.5A minimum - Charge time: 2 hours Environmental - IP-65 rated, when worn - Operating temperature -40°F (-40°C) to +158°F (+70°C) - Storage temperature -40°F (-40°C) to +185°F (+85°C) - Charging Temperature 32°F (0°C) to +104°F (+40°C)
SAE - Salt Spray per J1455, Sec. 4.3 - Vibration per J1455 Sec. 4.9 - Conducted Immunity per J1113-11 - Electrostatic Discharge per J1113-13 - Radiated Emissions per J1113-41 - Radiated Immunity per J1113-21
Power Off
To Order Firecom Accessories: Visit www.firecom.com Call: 1-800-527-0555
600-0176-00 RevD
Technical Spec
MIL SPEC - Humidity per MIL-STD 810F and 810G - Temperature Shock per MIL-STD 810F and 810G - Chemical Exposure per MIL-STD 810F and 810G
Power On
Up Center Down
H E A D S E T S
“The level of noise entering a person’s ear, when a hearing protector is worn as directed, is closely approximated by the difference between the A-weighted environmental noise level and the NRR.”
While holding the toggle switch UP or C Up=PTT On hold PTT button down on the dome
C
W I R E L E S S
UHW-Series Under the Helmet • FHW-Series Over the Head
ISO - Conducted Transients per 7637-2
Service phone: 503-684-6647 Service email:
[email protected]
Firecom 600-0176-00 RevD:Layout 1 8/19/11 3:15 PM Page 1
HEADSET FEATURES
CHARGING & INSTALLATIONS
BATTERY INDICATORS
PAIRING
LED Indicators: Charging Depleted Battery
0%
Power/Volume control
Charging Port Toggle-To-Talk Switch UP=Radio Center=Factory pre-set: Low Squelch DOWN=Factory pre-set: High Squelch
Charging Port
PTT Button
Mic Placement Place mic no more than 1/8" from lips. Placement of mic is critical for proper operation.
To avoid unpairing of existing Headsets, previously paired Headsets must be ON and connected before pairing a new Headset.
100%
Steady Green (Fully Charged)
Flashing Red (While Charging)
No Light (First 20 Minutes of Charging)
Power/Volume control
WARNING
2 Hours
20 Minutes
power ON to Base Station, press the “Pair” button until A With Yellow LINK(S) LED’s flash.
>75%
Wall Adapter Charging Only charge the Headset using the supplied 12VDC regulated wall adapter. Using unregulated wall adapters will damage the Headset charging circuit and components and void the warranty.
LINKS WIRELESS BASE
50-75%
Battery Level Indicator Number of RED and GREEN Flashes at Turn ON
POWER
INTERCOM
LINKS 1 2 3 4 5
PAIR
25-50% <25%
Headset to Base Station; hold toggle switch UP, then B Toturnpairpower ON to Headset or hold PTT button down on the dome while turning power ON to Headset. When BOTH Red/Green Headset LED’s are alternating, release toggle switch or PTT button. Headset will connect to base in 30 seconds.
Low Battery (2 hour battery life)
WARNING If the microphone is positioned incorrectly, you may experience a reduction or interruption in the audio and or deterioration in clarity of intercom and radio communication.
1 2 3 4 5
Vehicle Battery
Headset with Toggle Switch RED to Battery+
Headset Adjustments
Red LED Flashing Slow
3 Beeps Every 10 Minutes
Toggle Up
Power On
1.5A Fuse
Very Low Battery (15 Minutes battery life)
Behind-the-Head Headset
BLACK to Chassis Ground Adjustable headstrap
Vehicle Charging Note: Make fuse no further than 18" from the battery. Note: Only replace fuse with the same type, 1.5A AGU.
Headset with PTT Button
Up=PTT On C
PTT Button
Red LED Flashing Fast
1. The unterminated end of the supplied charging cable assembly and fuse assembly must be wired to the vehicle per the diagram above. 2. Observe correct polarity when connecting the charger cable to 12V from the vehicle. Connect the RED wire to +12V and the BLACK wire to battery chassis ground. This will result in a positive center terminal of the charger jack as shown in the illustration.
Over-the-Head Headsets
Adjustable headband Power/Volume control
Adjustable Boom
BLACK
RED
3. Charge Headset completely before use with vehicle power 12V supply or supplied wall mount charger. 4. For maximum battery shelf life, turn OFF the Headset.
6 Beeps Every Minute
Battery Life vs Temperature
C
30 Battery Capacity in Hours
Adjustable Boom
Power On
When the Headset Green LED remains steadily ON the headset is successfully paired to the base. If the Headset Green LED flashes rapidly then repeat the pairing procedure.
25 20 15 10 5
Paired
0 Degrees Centigrade
-40
Degrees Fahrenheit
-40
Up=PTT On -20 C -30
-22
-4
-10
0
14
32
C
Up=PTT On 20 . . . . . 60 10
50
68 . . . . .140
Not Paired
