Transcript
Flatliner PRO
Dying battery
12 VDC
The Flatliner PRO is a powerful, reliable and versatile power supply
This option offers creative guitarists the opportunity to simulate the
Some effects need higher voltages. Examples are: Boss ACA-type
for guitar and bass effects. Unlike many other power supplies
special effect that an almost empty battery causes in some fuzz and
effects, made before august 1997, need 12VDC for proper
Flatliners use toroidal transformers and have all isolated outlets
overdrive effects. The Flatliner PRO's dying battery outlets provide
functioning. You can connect these effects to the 12V DC outputs
to guarantee HUMless operation.
variable voltages from 3V-9V and 3-12V respectively in combination with
of the Flatliner PRO. All Boss PSA types and post-august 1997 ACA
It is designed to fit all existing effectpedals that need 9, 12, 18 or
a variable output resistances, to achieve the exact same electrical
effects you can connect to the 9VDC outputs.
F L AT L I N E R
24VDC and 9 or 12 VAC.
behaviour as a partly discharged battery.
The Flatliner PRO has 2 variable outputs that can simulate 'dying
More about the dying batteries option on www.burkey.nl.
18V/24VDC
Because all outputs are isolated it is possible to join two 9VDC or
batteries'.
Connecting
12 VDC outputs in a serial connection to double the voltage to 18
What's in the box ?
All Flatliner connectors and standard cables are of the standard size 2.1 x
or 24 VDC. (you need cable SC-YS Green)
" Flatliner PRO Power Supply
5.5 mm unless indicated.
" AC power cord
Some effects however require different connectors like a 3.5 mm
400mA
" 7 cables with 5.5x2.1 connectors center negative
phoneplug or 2.5 x 5.5 mm barrel (Line 6, some EHX, Digitech
For a pedals that need over 200mA current you can make a
" 1 cable with 5.5x2.1 connector center positive (Red Connector)
Whammy...).
parallel connection (Cable SC-YP Blue) between 2 equal DC outlets (9 or 12VDC) to double the current to 400mA.
" 1 cable with 3.5 mm connector for 9/12VAC output " Fuses 1x1AT 2x250mAT (230V) or 2x500mAT (115V)
Polarity
" Manual and Warranty Card
The polarity of the DC-outputs is center-negative standard for effectpedals.
which is
9/12 VAC Most tube-driven pedals* and the Line 6 Pods, Digitech Whammy,
PRO
NOTE !
Some pedals have reversed polarity (Fulltone '69,Line 6, Octafuzz, some
EHX Wiggler and many others, require 9VAC or 12 VAC output. Use
Please read this manual before using your Flatliner PRO for the first
EHX). To prevent damage to your pedals it is important to check the
the provided cable with 3.5 mm connector for 9/12VAC output.
time, to prevent damage to the Flatliner PRO or your pedals due to
polarity of the input jack of the pedal. A special cross-cable (SC-1R) is
improper usage!
provided with the Flatliner PRO to connect to a center positive
effectpedal. If you need more cables you can order them at our website
FUSES
Ready for use
(www.burkey.nl).
Your Flatliner PRO is protected against overheating and has a
All 9 outputs can operate simultaneously, without hum, noise or
short-circuit protection. This protection ensures that your
danger of overheating.
Standard 9VDC
The Flatliner PRO is designed for use on pedalboards and is
The Flatliner PRO has 8 DC outputs for the use of 5.5x2.1 mm
When you need to change a fuse just gently push and turn the
compact, rugged and indestructable built to guarantee many, many
barrel connectors (Boss-type). These are standard connectors
fuseholder left to open. Be sure to replace te same type fuse.
years of carefree and safe power. With our Flatliner PRO you have a
which fit most common effectpedals. The Line 6 modelling pedals
expensive effectpedals are safely powered.
well-organized and reliable setup ready for the wildest
can be powered through the 9V (MM4, FM4) or 12VDC (DM4,DL4)
More information is on our website www.burkey.nl. Additional
performances.
outputs. Since these effects draw more current (150-185 mA) than
cables can be ordered at our shop.
average you can connect one effect to one output. The Flatliner
Power features
*) Tube-driven pedals often need high currents at warming up. This may result in a
F L AT L I N E
- 5 isolated outputs 9 VDC 200mA short-circuit protected - 1 isolated output 12 VDC 200mA short-circuit protected
- 1 isolated variable output 3-9 VDC 200mA short-circuit protected dying battery option
PRO can power several Line 6 effects simultanously.
Note: Line 6 modelling pedals outputs are reversed polarity (center
blown fuse. In case your pedal blows the fuse at power on, you may use a fuse up to
1.5 AT.
positive). See the 'specials' list on www.burkey.nl for more
information about non-standard power requirements.
F L A T L I N E R
- 1 Isolated variable output 3-12 VDC 200mA short-circuit protected dying battery option - 1 isolated output 9V/12V AC 1000 mA fused 1AT
P O W E R
B Y
B U R K E Y
