Transcript
8
6
7
5
3
4
DWG NO.
NOTES: UNLESS OTHERWISE SPECIFIED
D
ZONE
CLEARANCE REQUIRED FOR FREE MOTION OF SYSTEM.
2
O-RING USED FOR SEALING SYSTEM TO MOUNTING STRUCTURE. STANDALONE UNIT MEETS IPX6 SEALING SPECIFICATION. MINIMUM MOUNTING SURFACE FLATNESS OF 1.5mm [0.60in] OVER SYSTEM DIAMETER REQUIRED FOR O-RING USE. WHEN MOUNTING TO IRREGULAR SURFACES, USE OF BEDDING COMPOUND RECOMMENDED.
4. 5
USE WITH FLIR MOUNTING HARDWARE KITS: 4115301 HARDWARE KIT - M-SERIES BASIC MOUNT 500-0396-00 TOP DOWN INSTALLATION KIT 500-0397-00 TOP DOWN INSTALLATION RISER KIT
1
120
REV
RELEASED PER ECN 106520 REVISED PER ECN #109004 REVISED PER ECN 112715
DATE
APPROVED
06/11/2009 02/19/2010 01/20/2011
MK MK MK
M-SERIES DUAL PAYLOAD
D
VISIBLE CAMERA 1
USE LOCTITE 242 WITH ALL METAL TO METAL THREADED CONNECTIONS.
7.3 184.2
WARNING DO NOT BOTTOM FASTENERS OUT IN BASE. BOLT LENGTH NOT TO EXCEED 6 mm INTO BASE. ELECTRONICS WILL BE DAMAGED BY BASE PENETRATION - VOIDING WARRANTY. BOLT TORQUE NOT TO EXCEED 12 N-m.
7.1 181.5
I.R. CAMERA
C
REV
1
REVISIONS DESCRIPTION
100 110 120
1
3
SH
432-0003-00
9.0 229.5
[11.6] 296.0
1
C
2 AS568A-427 EP O-RING [4.75in ID x 0.25in DIA. EP] 120mm ID x 7mm DIA. EP DWG NO.
AS568A-334 EP O-RING [2.63in ID x 0.19in DIA. EP] 67mm ID x 5mm DIA. EP
432-0003-00
7.0 177.8
CABLES SHOWN FOR REFERENCE ONLY. NOT TO SCALE, NOR CORRECT LENGTH.
B
3.9 100.0 BOLT CIRCLE
5
120
WARNING
6 HELICOILS 3
REV
6x M6x1.0
1in] POWER CABLE, UNTERMINATED TINNED 18AWG WIRE. 1in] NETWORK CABLE, RJ45 T568B, MALE. 1in] IR VIDEO CABLE, F-TYPE MALE. 1in] SWITCHED (IR OR VIS) VIDEO CABLE, F-TYPE MALE.
1
5.7 145.0 MIN BASE PLATE DIAMETER FOR EFFECTIVE O-RING SEAL.
25mm [15 25mm [18 25mm [21 25mm [23
SH
381 457 533 584
1.6 40.0 MIN CABLE PORT. 63.5 MAX THIRD ANGLE PROJECTION
THIS DOCUMENT IS CONTROLLED TO FLIR EAR TECHNOLOGY LEVEL 1.
IMPORTANT: CHASSIS GROUND SHALL BE TIED TO ONE MOUNTING FASTENER FOR HIGH CONDUCTIVE PATH TO VESSEL GROUND. MAX 0.25Ω.
A
METRIC
WARRANTY VOID IF SCREWS REMOVED.
INTERPRET DRAWING PER ASME Y14.5M-1994 ---------------------------------------------UNLESS OTHERWISE SPECIFIED SURFACE ROUGHNESS 32 .X = .25 .XX = .13 ANGULAR = .5 FILLET RADII = .13 MAX
8
7
6
5
4
THE INFORMATION CONTAINED IN THIS DOCUMENT PERTAINS TO A DUAL USE PRODUCT CONTROLLED FOR EXPORT BY THE EXPORT ADMINISTRATION REGULATIONS (EAR). FLIR TRADE SECRETS CONTAINED HEREIN ARE SUBJECT TO DISCLOSURE RESTRICTIONS AS A MATTER OF LAW. DIVERSION CONTRARY TO US LAW IS PROHIBITED. US DEPARTMENT OF COMMERCE AUTHORIZATION IS NOT REQUIRED PRIOR TO EXPORT OR TRANSFER TO FOREIGN PERSONS OR PARTIES UNLESS OTHERWISE PROHIBITED. MATERIAL
FINISH
N/A
UNLESS OTHERWISE SPECIFIED ALL MEASUREMENTS ARE IN MM. ALL DIMENSIONS IN [ ] ARE INCHES. DO NOT SCALE DRAWING.
CALC WT:
3
FLIR Systems, Inc. 70 Castilian Drive Goleta, CA 93117
PROJECT NO.
N/A
4188.949 GRAMS
APPROVALS DWN
MKENT
DATE
06/10/2009 TITLE
M-SERIES ICD, SINGLE / DUAL PAYLOAD
CHK DSGN ENG
MKENT
A
06/10/2009
APP
SIZE
D
CAGE
064Y2
DWG NO.
SCALE 1:2 PRINTED: 1/20/2011 SHEET
2
REV
432-0003-00 120 1 OF 11
1
8
6
7
5
4
3
DWG NO.
SH
432-0003-00
2
REV
1
120
NOTES: UNLESS OTHERWISE SPECIFIED
D
1
CLEARANCE REQUIRED FOR FREE MOTION OF SYSTEM.
2
O-RING USED FOR SEALING SYSTEM TO MOUNTING STRUCTURE. STANDALONE UNIT MEETS IPX6 SEALING SPECIFICATION. MINIMUM MOUNTING SURFACE FLATNESS OF 1.5mm [0.60in] OVER SYSTEM DIAMETER REQUIRED FOR O-RING USE. WHEN MOUNTING TO IRREGULAR SURFACES, USE OF BEDDING COMPOUND RECOMMENDED.
3
4. 5
D
M-SERIES SINGLE PAYLOAD
USE WITH FLIR MOUNTING HARDWARE KITS: 4115301 HARDWARE KIT - M-SERIES BASIC MOUNT 500-0396-00 TOP DOWN INSTALLATION KIT 500-0397-00 TOP DOWN INSTALLATION RISER KIT USE LOCTITE 242 WITH ALL METAL TO METAL THREADED CONNECTIONS.
6.6 168.0
I.R. CAMERA
1
WARNING DO NOT BOTTOM FASTENERS OUT IN BASE. BOLT LENGTH NOT TO EXCEED 6 mm INTO BASE. ELECTRONICS WILL BE DAMAGED BY BASE PENETRATION - VOIDING WARRANTY. BOLT TORQUE NOT TO EXCEED 12 N-m.
1
[11.3] 287.0
C
C
7.8 198.5
2 7.0 177.8
DWG NO.
AS568A-427 EP O-RING [4.75in ID x 0.25in DIA. EP] 120mm ID x 7mm DIA. EP
B
432-0003-00
AS568A-334 EP O-RING [2.63in ID x 0.19in DIA. EP] 67mm ID x 5mm DIA. EP
CABLES SHOWN FOR REFERENCE ONLY. NOT TO SCALE, NOR CORRECT LENGTH. 381 25mm [15 1in] POWER CABLE, UNTERMINATED TINNED 18AWG WIRE. 457 25mm [18 1in] NETWORK CABLE, RJ45 T568B, MALE. 533 25mm [21 1in] IR VIDEO CABLE, F-TYPE MALE.
2 REV
3.9 100.0 BOLT CIRCLE
SH
5.7 145.0 MIN BASE DIAMETER FOR EFFECTIVE SEAL
120
6x M6x1.0
6 HELICOILS 3
WARNING
5
THIRD ANGLE PROJECTION
1.6 40.0 MIN CABLE PORT 63.5 MAX
METRIC
IMPORTANT: CHASSIS GROUND SHALL BE TIED TO ONE MOUNTING FASTENER FOR HIGH CONDUCTIVE PATH TO VESSEL GROUND. MAX 0.25Ω.
A
INTERPRET DRAWING PER ASME Y14.5M-1994 ---------------------------------------------UNLESS OTHERWISE SPECIFIED SURFACE ROUGHNESS 32 .X = .25 .XX = .13 ANGULAR = .5 FILLET RADII = .13 MAX
WARRANTY VOID IF SCREWS REMOVED.
SIZE
D
CAGE
064Y2
DWG NO.
432-0003-00
SCALE 1:5 PRINTED: 1/20/2011 SHEET
8
7
6
5
4
3
2
2 OF
1
REV
120
11
A
4
3
DWG NO.
432-0003-00
SH
1
3 REV 120
IMPORTANT NOTE: PAPER SIZE: 11x17in TEMPLATE SHOULD PRINT 1:1
D .3 6x 6.4 THRU HOLE EQUALLY SPACED ON 100 [3.94] BOLT CIRCLE
D
DUE TO VARIATION IN SOFTWARE AND PRINTERS, PLEASE VERIFY SCALE BELOW BEFORE MODIFYING MOUNTING SURFACE.
2.00IN
C
C 50.0MM
40.0 [1.57] MIN CABLE PORT. 63.5 [2.50] MAX
B
B
THIRD ANGLE PROJECTION
METRIC
7.1 179.4 M-SERIES O.D.
A
INTERPRET DRAWING PER ASME Y14.5M-1994 ---------------------------------------------UNLESS OTHERWISE SPECIFIED SURFACE ROUGHNESS 32 .X = .25 .XX = .13 ANGULAR = .5 FILLET RADII = .13 MAX
MOUNTING TEMPLATE M-SERIES GIMBAL
4
3
2
SIZE CAGE
B
SCALE 1:1
064Y2
DWG NO.
432-0003-00
PRINTED: 1/20/2011 SHEET
1
REV
120
3 OF 11
A
8
6
7
5
3
4
D
1.3 31.9
3.6 90.4
DWG NO.
SH
432-0003-00
4
REV
1
120
D
3.0 77.3
5.6 141.4
C
C
WITH CABLE INSTALLED, TURN NUT 1/4 TURN BEYOND HAND TIGHT.
GLAND SEAL DESIGNED FOR USE WITH DOUBLE SHIELDED CAT 5 ETHERNET CABLE. USE OF SINGLE SHIELDED CABLE MAY REQUIRE THE USE OF ADDITIONAL SEALANT SUCH AS SILICON OR RTV TO ENSURE SEALING OF ENCLOSURE. IP64 RATED BEHIND GASKET.
DWG NO.
IP66 RATED ABOVE GASKET.
INSERT NETWORK CABLE RJ45 THROUGH GLAND NUT AND SEAL BEFORE INSTALLING.
432-0003-00
B
APPLY ADHESIVE SIDE OF GASKET TO JCU BODY. SH
4 REV
120
2.4 60.9
MOUNTING PANEL THICKNESS RANGE 1.6-45 [0.063-1.750]. WHEN MOUNTING TO PANELS LESS THAN 6.3 [0.25] REVERSE PADDLES AS ILLUSTRATED.
METRIC THIRD ANGLE PROJECTION
A
INTERPRET DRAWING PER ASME Y14.5M-1994 ---------------------------------------------UNLESS OTHERWISE SPECIFIED SURFACE ROUGHNESS 32 .X = .25 .XX = .13 ANGULAR = .5 FILLET RADII = .13 MAX
DURING INITIAL TIGHTENING, ENSURE MOUNTING TABS ON SCREWS SWING FREE OF REAR HOUSING. WITH TABS RUN UP AGAINST REAR OF INSTRUMENT PANEL, TIGHTEN 1/4-1/2 TURN BEYOND HAND TIGHT.
M-SERIES JCU 8
7
6
5
4
3
2
SIZE
D
CAGE
064Y2
500-0385-00
PIECE PART.
SCALE 1:1 PRINTED: 1/20/2011 SHEET
4 OF
1
REV
120
11
A
4
D
CORNERS SHALL BE SHARP.
3
DWG NO.
432-0003-00
SH
1
5 REV 120
IMPORTANT NOTE:
2.9 72.4 OPTIONAL DRILL GUIDE
PAPER SIZE: 11x17in TEMPLATE SHOULD PRINT 1:1
D
DUE TO VARIATION IN SOFTWARE AND PRINTERS, PLEASE VERIFY SCALE BELOW BEFORE MODIFYING MOUNTING SURFACE. FITS JCU P.N. 500-0385-00
2.00IN
C 4.9 123.2 OPTIONAL DRILL GUIDE
5.100±.049 129.54±1.25 CUTOUT
5.6 141.4 OUTSIDE OF JCU
C
50.0MM
.25 6.4
B
B
3.100±.049 78.74±1.25 CUTOUT
THIRD ANGLE PROJECTION
METRIC
3.6 90.4 OUTSIDE OF JCU
A
4
INTERPRET DRAWING PER ASME Y14.5M-1994 ---------------------------------------------UNLESS OTHERWISE SPECIFIED SURFACE ROUGHNESS 32 .X = .25 .XX = .13 ANGULAR = .5 FILLET RADII = .13 MAX SIZE CAGE
3
2
MOUNTING TEMPLATE B SCALE M-SERIES JCU
1:1
064Y2
DWG NO.
432-0003-00
PRINTED: 1/20/2011 SHEET
1
REV
120
5 OF 11
A
8
6
7
D
5
4
3
DWG NO.
SH
432-0003-00
6
REV
1
120
D
M-SERIES SINGLE /DUAL PAYLOAD
JCU FLIR P.N. 500-0385-00
ATTACH GROUNDING STRAP TO MOUNTING STUD POWER CABLE 18AWG TINNED STRANDED WIRE RED WIRE: +12-24 VDC (3.8-1.9 AMP MAX) BLK WIRE: DC RETURN GRN WIRE: EARTH GROUND
C
C CONNECTOR RJ45 WATERPROOF ENCLOSURE FLIR PN 4115028
NETWORK CABLE FOR PoE DEVICES (IEEE802.3af) 8 CONDUCTOR T568B, ETHERNET, DOUBLE SHIELDED FLIR PN 308-0163-25 OR EQUIVALENT NOTE: TO MAINTAIN IEC 60945 EMI COMPLIANCE, USE OF DOUBLE SHIELDED CABLE REQUIRED.
BUTT SPLICE OR INSTALLER SUPPLIED CONNECTOR
DWG NO.
RG59U VIDEO CABLE F-TYPE MALE TERMINATION
SWITCHED (IR OR VIS) VIDEO CABLE (DUAL PAYLOAD ONLY)
INSTALLER SUPPLIED POWER CABLE
B
432-0003-00
DISPLAY
SH
GAUGE OF WIRE TO BE APPROPRIATE FOR SUPPLY VOLTAGE AND LENGTH OF CABLE RUN TO ENSURE ADEQUATE CURRENT CARRYING CAPABILITY.
6 REV
120
IR VIDEO CABLE
CONNECTOR F-TYPE FEMALE TO FEMALE FLIR PN 4115330
INSTALLER SUPPLIED VIDEO CABLE SHALL BE RATED RG59U OR BETTER
A
A
INTERCONNECT DIAGRAM SINGLE JCU SIZE
D
CAGE
064Y2
DWG NO.
432-0003-00
SCALE 1:2 PRINTED: 1/20/2011 SHEET
8
7
6
5
4
3
2
6 OF
1
REV
120
11
8
6
7
5
3
4
DWG NO.
SH
432-0003-00
7
REV
1
120
M-SERIES SINGLE / DUAL PAYLOAD
D
D
JCU 1
JCU 2 FLIR P.N. 500-0385-00
MANUFACTURER SPECIFIC ENVIRONMENTAL EXPOSURE RATINGS APPLY POWER CABLE 18AWG TINNED STRANDED WIRE RED WIRE: +12-24 VDC (3.8-1.9 AMP MAX) BLK WIRE: DC RETURN GRN WIRE: EARTH GROUND
C
C POE NETWORK SWITCH IEEE802.3af, T568B COMPLIANT INSTALLER SUPPLIED
ATTACH GROUNDING STRAP TO MOUNTING STUD
BUTT SPLICE OR INSTALLER SUPPLIED CONNECTOR
CONNECTOR RJ45 WATERPROOF ENCLOSURE FLIR PN 4115028
DWG NO.
NETWORK CABLE FOR PoE DEVICES (IEEE802.3af) 8 CONDUCTOR T568B, ETHERNET, DOUBLE SHIELDED FLIR PN 308-0163-25 OR EQUIVALENT NOTE: TO MAINTAIN IEC 60945 EMI COMPLIANCE, USE OF DOUBLE SHIELDED CABLE REQUIRED.
432-0003-00
RG59U VIDEO CABLE F-TYPE MALE TERMINATION INSTALLER SUPPLIED POWER CABLE
B
GAUGE OF WIRE TO BE APPROPRIATE FOR SUPPLY VOLTAGE AND LENGTH OF CABLE RUN TO ENSURE ADEQUATE CURRENT CARRYING CAPABILITY.
SH
DISPLAY
7 REV
120
SWITCHED (IR OR VIS) VIDEO CABLE (DUAL PAYLOAD ONLY)
CONNECTOR F-TYPE FEMALE TO FEMALE FLIR PN 4115330 IR VIDEO CABLE
A
A
INSTALLER SUPPLIED VIDEO CABLE SHALL BE RATED RG59U OR BETTER
INTERCONNECT DIAGRAM MULTIPLE JCU - POE SWITCH SIZE
D
CAGE
064Y2
DWG NO.
432-0003-00
SCALE 1:2 PRINTED: 1/20/2011 SHEET
8
7
6
5
4
3
2
7 OF
1
REV
120
11
8
6
7
D
5
3
4
DWG NO.
SH
432-0003-00
8
REV
1
120
D
M-SERIES SINGLE / DUAL PAYLOAD
JCU 1
JCU 2 FLIR P.N. 500-0385-00
MANUFACTURER SPECIFIC ENVIRONMENTAL EXPOSURE RATINGS APPLY POWER CABLE 18AWG TINNED STRANDED WIRE RED WIRE: +12-24 VDC (3.8-1.9 AMP MAX) BLK WIRE: DC RETURN GRN WIRE: EARTH GROUND
C
C NETWORK SWITCH, NON PoE INSTALLER SUPPLIED
ATTACH GROUNDING STRAP TO MOUNTING STUD BUTT SPLICE OR INSTALLER SUPPLIED CONNECTOR
POE INJECTOR IP20, RJ45 FEMALE FLIR PN 4113746
432-0003-00
POE INJECTOR POWER REQUIREMENT +9-36VDC (12V/1.85A - 24V/0.90A)
INSTALLER SUPPLIED POWER CABLE
B
NETWORK CABLE FOR PoE DEVICES (IEEE802.3af) 8 CONDUCTOR T568B, ETHERNET, DOUBLE SHIELDED FLIR PN 308-0163-25 OR EQUIVALENT NOTE: TO MAINTAIN IEC 60945 EMI COMPLIANCE, USE OF DOUBLE SHIELDED CABLE REQUIRED.
DWG NO.
CONNECTOR RJ45 WATERPROOF ENCLOSURE FLIR PN 4115028
GAUGE OF WIRE TO BE APPROPRIATE FOR SUPPLY VOLTAGE AND LENGTH OF CABLE RUN TO ENSURE ADEQUATE CURRENT CARRYING CAPABILITY.
SH
DISPLAY
8 REV
120
SWITCHED (IR OR VIS) VIDEO CABLE (DUAL PAYLOAD ONLY)
RG59U VIDEO CABLE F-TYPE MALE TERMINATION
CONNECTOR F-TYPE FEMALE TO FEMALE FLIR PN 4115330 IR VIDEO CABLE
INSTALLER SUPPLIED VIDEO CABLE SHALL BE RATED RG59U OR BETTER
A
A
INTERCONNECT DIAGRAM MULTIPLE JCU - POE INJECTOR SIZE
D
CAGE
064Y2
DWG NO.
432-0003-00
SCALE 1:2 PRINTED: 1/20/2011 SHEET
8
7
6
5
4
3
2
8 OF
1
REV
120
11
8
6
7
5
4
3
GIMBAL ASSEMBLY WEIGHT: 4746 GRAMS 10.5 LBS
DWG NO.
SH
432-0003-00
9
REV
1
120
CUSTOMER BULKHEAD SEAL, OPTIONAL PER APPLICATION.
SOC HD CAP SCREW M6 X 1.0 LENGTH: 6 MM + THICKNESS OF CUSTOMER DECKING 316 STAINLESS STEEL 6 PLACES APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT) TORQUE TO 9.5 N-m [7 LB-f]
D
WARNING
IMPORTANT: CHASSIS GROUND SHALL BE TIED TO ONE MOUNTING FASTENER FOR HIGH CONDUCTIVE PATH TO VESSEL GROUND. MAX 0.25Ω.
5
WASHER, OPTIONAL M6 316 STAINLESS STEEL
AS568A-427 EP O-RING [4.75in ID x 0.25in DIA. EP] 120mm ID x 7mm DIA. EP FITS IN LARGER DIAMETER GLAND OF GIMBAL ASSY
C
D
CUSTOMER STRUCTURE, SEALED ENCLOSURE, DRY SPACE SHOWN SECTIONED AND BROKEN AWAY
C
CUSTOMER DECKING, OR OTHER STRUCTURE
HOLES, MOUNTING 6.4 MM DIAMETER 6 PLACES
HOLES, MOUNTING 6.4 MM DIAMETER 6 PLACES HOLE CABLE PASS 40.0 MM DIAMETER MIN. 63.5 MM DIAMETER MAX. DWG NO.
B
432-0003-00
AS568A-427 EP O-RING [4.75in ID x 0.25in DIA. EP] 120mm ID x 7mm DIA. EP FITS IN LARGER DIAMETER GLAND OF GIMBAL ASSY
SH
HOLE CABLE PASS 40.0 MM DIAMETER MIN. 63.5 MM DIAMETER MAX.
9
IMPORTANT: CHASSIS GROUND SHALL BE TIED TO ONE MOUNTING FASTENER FOR HIGH CONDUCTIVE PATH TO VESSEL GROUND. MAX 0.25Ω.
REV
120
WASHER, OPTIONAL M6 316 STAINLESS STEEL
SOC HD CAP SCREW M6 X 1.0 LENGTH: 6 MM + THICKNESS OF CUSTOMER DECKING 316 STAINLESS STEEL 6 PLACES APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT) TORQUE TO 9.5 N-m [7 LB-f]
GIMBAL ASSEMBLY WEIGHT: 4746 GRAMS 10.5 LBS
WARNING 5
HIDDEN CABLING MOUNTING SCHEME:
HIDDEN CABLING MOUNTING SCHEME:
A
MOUNTING DIRECTLY TO CUSTOMER STRUCTURE, ACTUAL STRUCTURES MAY VARY. CAMERA BALL DOWN CONFIGURATION
MOUNTING DIRECTLY THRU CUSTOMER DECKING, OR OTHER SURFACES. STRUCTURE OPPOSITE GIMBAL TO BE SEALED ENCLOSURE AND A DRY SPACE. CAMERA BALL UP CONFIGURATION
ENTIRE ASSEMBLY VIEW CAN BE ROTATED 180° FOR BALL UP INSTALLATION.
ENTIRE ASSEMBLY VIEW CAN BE ROTATED 180° FOR BALL DOWN INSTALLATION.
NOTE HOME DIRECTION FOR BALL UP/ DOWN, INSTALL AS INDICATED ON BASE OF UNIT.
NOTE HOME DIRECTION FOR BALL UP/ DOWN, INSTALL AS INDICATED ON BASE OF UNIT.
8
7
6
A
SIZE
D
SCALE: 3/8
5
4
CAGE
064Y2
DWG NO.
432-0003-00
SCALE 1:2 PRINTED: 1/20/2011 SHEET
3
2
9 OF
1
REV
120
11
8
7
5
4
3
DWG NO.
SH
432-0003-00
10
REV
1
120
NUT, HEX (NYLOCK AND ACORN NUTS, OPTIONAL) M6 X 1.0 316 STAINLESS STEEL 6 PLACES APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT)
IMPORTANT: CHASSIS GROUND SHALL BE TIED TO ONE MOUNTING FASTENER FOR HIGH CONDUCTIVE PATH TO VESSEL GROUND. MAX 0.25Ω.
D
6
WASHER, OPTIONAL M6 316 STAINLESS STEEL 6 PLACES
D
CONDUIT AND FITTINGS CUSTOMER SUPPLIED PARTS SHOWN, EXAMPLE ONLY
IMPORTANT: CHASSIS GROUND SHALL BE TIED TO ONE MOUNTING FASTENER FOR HIGH CONDUCTIVE PATH TO VESSEL GROUND. MAX 0.25Ω.
HOLES, MOUNTING 6.4 MM DIAMETER 6 PLACES
NUT, HEX (NYLOCK AND ACORN NUTS, OPTIONAL) M6 X 1.0 316 STAINLESS STEEL 6 PLACES APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT)
WASHER, OPTIONAL M6 316 STAINLESS STEEL 6 PLACES CONDUIT HUB HOLE CABLE PASS 40.0 MM DIAMETER MIN. 63.5 MM DIAMETER MAX.
C
MOUNT, CAMERA CUSTOMER SUPPLIED UNIT SHOWN EXAMPLE ONLY
SPACER, THRU 6.4 ID X 17.3 OD X 3.2 THICK 316 STAINLESS STEEL 6 PLACES
C
HOLE CABLE PASS 40.0 MM DIAMETER MIN. 50.4 MM DIAMETER MAX. (FOR O-RING SEAL)
HOLES, MOUNTING 6.4 MM DIAMETER 6 PLACES
MOUNT, CAMERA CUSTOMER SUPPLIED UNIT SHOWN EXAMPLE ONLY
STUD, MALE M6 X 1.0 (LENGHT 16 MM + THICKNESS OF MOUNT) 316 STAINLESS STEEL 6 PLACES APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT)
5
B
WARNING
432-0003-00
WARNING
DWG NO.
STUD, MALE M6 X 1.0 (LENGHT 19 MM + THICKNESS OF MOUNT) 316 STAINLESS STEEL 6 PLACES APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT)
5 SH
10
AS568A-334 EP O-RING [2.65in ID x 0.19in DIA. EP] 67mm ID x 5mm DIA. EP FITS IN SMALLER DIAMETER GLAND OF GIMBAL ASSY
REV
120
GIMBAL ASSEMBLY WEIGHT: 4746 GRAMS 10.5 LBS GIMBAL ASSEMBLY WEIGHT: 4746 GRAMS 10.5 LBS
A
A EXPOSED CABLING MOUNTING SCHEME:
EXPOSED CABLING MOUNTING SCHEME:
CUSTOMER PROVIDED MOUNTING BRACKET / SURFACE CAMERA BALL DOWN CONFIGURATION
CUSTOMER PROVIDED MOUNTING BRACKET / SURFACE CAMERA BALL DOWN CONFIGURATION
NOTE HOME DIRECTION FOR BALL UP/ DOWN, INSTALL AS INDICATED ON BASE OF UNIT.
8
7
6
SIZE
D
NOTE HOME DIRECTION FOR BALL UP/ DOWN, INSTALL AS INDICATED ON BASE OF UNIT.
5
4
3
CAGE
064Y2
DWG NO.
432-0003-00
SCALE 1:2 PRINTED: 1/20/2011 SHEET
2
10 OF
1
REV
120
11
8
6
7
5
3
4
DWG NO.
SH
432-0003-00
11
REV
1
120
CHASSIS GROUND SHALL BE TIED TO MOUNTING FASTENER FOR HIGH CONDUCTIVE PATH TO VESSEL GROUND. MAX 0.25Ω. (CUSTOMER SUPPLIED) GIMBAL ASSEMBLY WEIGHT: 4746 GRAMS 10.5 LBS
D
D
DETAIL A SCALE 1 : 1 ALTERNATE TO MOUNT SHOWN IN ASSEMBLY PELAGIC BASE CONNECTOR COMPARTMENT FLIR P/N 500-0397-00
GROUNDING SCHEME
AS568A-427 EP O-RING [4.75in ID x 0.25in DIA. EP] 120mm ID x 7mm DIA. EP FITS IN LARGER DIAMETER GLAND OF GIMBAL ASSY
C
C M6 SCREWS, FLAT HEAD SOC CAP OR, 1/4"-20 SCREWS, FLAT HEAD SOC CAP OR, #14 X 1.5 SCREWS, FLAT HEAD PHILLIPS SHEET METAL TYPE AND LENGTH DEPENDANT ON MOUNTING SURFACE 316 STAINLESS STEEL 6 PLACES APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT) TOP DOWN BASE FLIR P/N 500-0396-00 SEE FLIR P/N 500-0397-00 (ALTERNATE)
AS568A-440 EP O-RING [6.75in ID x 0.25in DIA. EP] 171mm ID x 7mm DIA. EP FITS IN LARGER DIAMETER GLAND OF GIMBAL ASSY DWG NO.
CHASSIS GROUND
B
WARNING
432-0003-00
SOC HD CAP SCREW M6 X 1.0 X 10 MM LONG 316 STAINLESS STEEL 6 PLACES APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT) TORQUE TO 9.5 N-m [7 LB-f] 5
SH
HOLE CABLE PASS 40.0 MM DIAMETER MIN. 63.5 MM DIAMETER MAX.
11 REV
120
CUSTOMER DECKING, OR OTHER STRUCTURE
HIDDEN CABLING MOUNTING SCHEME
A
A
FLIR PROVIDED MOUNTING BRACKET(S) CAMERA BALL UP CONFIGURATION ENTIRE ASSEMBLY VIEW CAN BE ROTATED 180° FOR BALL DOWN INSTALLATION NOTE HOME DIRECTION FOR BALL UP/ DOWN, INSTALL AS INDICATED ON BASE OF UNIT.
SIZE
D
SCALE: 3/8
8
7
6
5
CAGE
064Y2
DWG NO.
432-0003-00
SCALE 1:5 PRINTED: 1/20/2011 SHEET
4
3
2
11 OF
1
REV
120
11
